同步辐射小角x射线散射方法研究由城市固体垃圾制备的活性炭

应用同步辐射小角x射线散射方法研究了由不同城市固体垃圾制备而成的活性炭的孔结构-结果发现利用木类、纸张、塑料这三类典型垃圾组分的热解残余物为原料制备中孔发达的活性炭是可行的-活性炭的形态和结构取决于垃圾热解残余物的组分和热解程度等因素- 关键词： 小角x射线散射 活性炭 分形维数 平均孔径     

Axisymmetric frictionless contact of functionally graded materials

The main interest of this study is a new method to solve the axisymmetric frictionless contact problem of functionally graded materials (FGMs). Based on the fact that an arbitrary curve can be approached by a series of continuous but piecewise linear curves, the FGM is divided into a series of sub-layers with shear modulus varying linearly in each sub-layer and continuous at the sub-interfaces. With this model, the axisymmetric frictionless contact problem of a functionally graded coated half-space is investigated. By using the transfer matrix method and Hankel integral transform technique, the problem is reduced to a Cauchy singular integral equation. The contact pressure, contact region and indentation are calculated for various indenters by solving the equations numerically. An erratum to this article can be found at     

N[a,b]类中边界Nevanlinna-Pick插值(I)

用所谓的Hankel向量方法求解N[a,b]函数类中带边界插值数据的Nevanlina-Pick插值(BNP(N[a,b]))问题,并建立BNP(N[a,b])问题与[a,b]上的某种带约束条件的Hausdorff矩量问题之间等价的可解条件以及解之间明确的一一对应关系.这使得当BNP(N[a,b])问题有多解时,能通过带约束条件的矩量问题的可解性准则和解获得BNP(N[a,b])问题的可解性准则和解的参数化描述,而在唯一解的情况下,通过BNP(N[a,b])问题解的存在唯一性准则和唯一解来获得带约束条件的     

注入控制铜蒸气激光方向性时间过程测量

实验研究了注入控制对铜蒸气激光非稳腔输出光束质量的影响，从输出光发散角时间分辨过程的测量结果说明注入加速被注入腔内激光发散角的减小过程。由于被注入腔内放大自发辐射的存在，为得到较好的注入控制效果，注入光的脉宽和进入被注入腔的延时必须恰当。     

The role of binder mobility in spontaneous adhesive contact and implications for cell adhesion

The standard view of mechanical adhesive contact is as a competition between a reduction in free energy when surfaces with bonding potential come into contact and an increase in free energy due to elastic deformation that is required to make these surfaces conform. An equilibrium state is defined by an incremental balance between these effects, akin to the Griffith crack growth criterion. In the case of adhesion of biological cells, the molecules that tend to form surface-to-surface bonds are confined to the cell wall but they are mobile within the wall, adding a new phenomenon of direct relevance to adhesive contact. In this article, the process of adhesive contact of an initially curved elastic plate to a flat surface is studied for the case in which the binders that account for adhesion are able to migrate within the plate. This is done by including entropic free energy of the binder distribution in the total free energy of the system. By adopting a constitutive assumption that binders migrate at a speed proportional to the local gradient in chemical potential, the transient growth of an adhesion zone due to binder transport is analyzed. For the case of a plate of very large extent, the problem can be solved in closed form, whereas numerical methods are invoked for the case of a plate of limited extent. Results are presented on the rate of growth of an adhesion zone in terms of system parameters, on the evolution of the distribution of binders and, in the case of a plate of limited extent, on the long-term limiting size of the adhesion zone.     

THE GENERALIZED MAXIMUM ANGLE CONDITION FOR THE Q1 ISOPARAMETRIC ELEMENT

We consider the quadrilateral Q1 isoparametric element and establish an optimal error estimate in H^1 norm for the interpolation operator under a weaker mesh condition which admits anisotropic quadrilaterals and allows the quadrilateral to become a regular triangle in the sense of maximum angle condition [5, 11].     

Modification of surface properties of electrospun polyamide nanofibers by means of a perfluorinated acridine

Polyamide 6 (PA6) nanofibers were prepared from formic acid solutions by using electrospinning technique. The fibers were smooth, defects free and with diameters smaller than 200 nm. Small amounts of a perfluorinated acridine were added as dopant to the feed solution to modify the wettability of the fibers. The effect of doping on the contact angle values is well apparent. The contact angle values go from 50° of pure PA6 to 120° when 6% of acridine is added. A comparison between fibers and films of pure and doped polyamide 6 was carried out in order to determine the effect of morphology on wettability. Thermal annealing near the T_g of the polymer promoted the segregation of the molecules to the surface, reaching contact angles of 131° with smaller amounts (4%) of acridine. The surface segregation was also promoted by time aging.     

Atom transfer radical polymerization directly from poly(vinylidene fluoride): Surface and antifouling properties

The direct preparation of grafting polymer brushes from commercial poly (vinylidene fluoride) (PVDF) films with surface‐initiated atom transfer radical polymerization (ATRP) is demonstrated. The direct initiation of the secondary fluorinated site of PVDF facilitated grafting of the hydrophilic monomers from the PVDF surface. Homopolymer brushes of 2‐(N,N‐dimethylamino)ethyl methacrylate (DMAEMA) and poly (ethylene glycol) monomethacrylate (PEGMA) were prepared by ATRP from the PVDF surface. The chemical composition and surface topography of the graft‐functionalized PVDF surfaces were characterized by X‐ray photoelectron spectroscopy, attenuated total reflectance/Fourier transform infrared spectroscopy, and atomic force microscopy. A kinetic study revealed a linear increase in the graft concentration of poly[2‐(N,N‐dimethylamino)ethyl methacrylate] (PDMAEMA) and poly[poly(ethylene glycol) monomethacrylate] (PPEGMA) with the reaction time, indicating that the chain growth from the surface was consistent with a controlled or living process. The living chain ends were used as macroinitiators for the synthesis of diblock copolymer brushes. The water contact angles on PVDF films were reduced by the surface grafting of DMAEMA and PEGMA. Protein adsorption experiments revealed a substantial antifouling property of PPEGMA‐grafted PVDF films and PDMAEMA‐grafted PVDF films in comparison with the pristine PVDF surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3434–3443, 2006     

A procedure for measuring the flexibility of single wood-pulp fibres

A way of determining the flexibility of wood-pulp fibres is developed, which involves i) a precise measurement of the topology of single-fibres by using a confocal laser scanning microscope and ii) the measurement of the elastic modulus of the fibres by using a single-fibre fatigue cell. Reported in this paper are the initial results of tests carried out on black spruce fibres, which have been subjected to three different levels of mechanical refining energy, namely ∼1100, 2300, and 3500 kWh/t. It is found that the fibre flexibility rises significantly between the first and second energy levels, but it does not change to the same degree between the second and third ones. The described procedure of measuring the flexibility of fibres may be used to establish the appropriate refiner energy necessary for the production of a specific grade of paper. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 1, pp. 115–128, January–February, 2006.