Mössbauer study of nanodimensional nickel ferrite – mechanochemical synthesis and catalytic properties

Iron–nickel spinel oxide NiFe₂O₄ nanoparticles have been prepared by the combination of chemical precipitation and subsequent mechanical milling. For comparison, their analogue obtained by thermal synthesis is also studied. Phase composition and structural properties of iron–nickel oxides are investigated by X-ray diffraction and Mössbauer spectroscopy. Their catalytic behavior in methanol decomposition to CO and methane is tested. An influence of the preparation method on the reduction and catalytic properties of iron–nickel samples is established.     

Singlewall carbon nanotubes covered with polystyrene nanoparticles by in‐situ miniemulsion polymerization

This work is to make carbon nanotubes dispersible in both water and organic solvents without oxidation and cutting nanotube threads. Polystyrene‐singlewall carbon nanotube (PS‐SWNT) composites were prepared with three different methods: miniemulsion polymerization, conventional emulsion polymerization, and mixing SWNT with PS latex. The two factors, crosslinking and surface coverage of PS are important factors for the mechanical and electrical properties, including dispersion states of SWNT in various solvents. The PS‐SWNT composite prepared via a conventional emulsion polymerization showed SWNT bundles entirely covered with PS, whereas the PS‐SWNT composite prepared via a miniemulsion polymerization showed SWNT partially covered with crosslinked PS nanoparticles. The method of mixing SWNTs with PS latex did not show the well dispersed state of carbon nanotubes because PS was not crosslinked and was dissolved in a solvent, and nanotubes separated from PS precipitated. So the PS nanoparticle‐SWNT composite had lower electrical resistance, and higher mechanical strength than the other composites made by the latter two methods. As the amount of SWNT increases, the bare surface area of SWNT increases and the electrical conductivity increases in the composite made by the miniemulsion polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 573–584, 2006     

Facile syntheses of surface-functionalized micelles and shell cross-linked nanoparticles

Block copolymer micelles and shell cross-linked nanoparticles (SCKs) presenting Click-reactive functional groups on their surfaces were prepared using two separate synthetic strategies, each employing functionalized initiators for the controlled radical polymerization of acrylate and styrenic monomers to afford amphiphilic block copolymers bearing an alkynyl or azido group at the α-terminus. The first route for the synthesis of the azide-functionalized nanostructures was achieved via sequential nitroxide-mediated radical polymerization (NMP) of tert-butyl acrylate and styrene, originating from a benzylic chloride-functionalized initiator, followed by deprotection of the acrylic acids, supramolecular assembly of the block copolymer in water and conversion of the benzylic chloride to a benzylic azide. In contrast, the second strategy utilized an alkynyl-functionalized reversible addition fragmentation transfer (RAFT) agent directly for the RAFT-based sequential polymerization of tetrahydropyran acrylate and styrene, followed by selective cleavage of the tetrahydropyran esters to give the α-alkynyl-functionalized block copolymers. These Click-functionalized polymers, with the functionality located at the hydrophilic polymer termini, were then self-assembled using a mixed-micelle methodology to afford surface-functionalized “Clickable” micelles in aqueous solutions. The optimum degree of incorporation of the Click-functionalized polymers was investigated and determined to be ca. 25%, which allowed for the synthesis of well-defined surface-functionalized nanoparticles after cross-linking selectively throughout the shell layer using established amidation chemistry. Functionalization of the chain ends was shown to be an efficient process under standard Click conditions and the resulting functional groups revealed a more “solution-like” environment when compared to the functional group randomly inserted into the hydrophilic shell layer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5203–5217, 2006     

Synthesis of silicon nitride based ceramic nanoparticles by the pyrolysis of silazane block copolymer micelles

Diblock copolymer poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane)‐block‐polystyrene (polyVSA‐b‐polySt) and triblock copolymer poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane)‐block‐polystyrene‐block‐poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane) (polyVSA‐b‐polySt‐b‐polyVSA), consisting of silazane and nonsilazane segments, were prepared by the living anionic polymerization of 1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane and styrene. PolyVSA‐b‐polySt formed micelles having a poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane) (polyVSA) core in N,N‐dimethylformamide, whereas polyVSA‐b‐polySt and polyVSA‐b‐polySt‐b‐polyVSA formed micelles having a polyVSA shell in n‐heptane. The micelles with a polyVSA core were core‐crosslinked by UV irradiation in the presence of diethoxyacetophenone as a photosensitizer, and the micelles with a polyVSA shell were shell‐crosslinked by UV irradiation in the presence of diethoxyacetophenone and 1,6‐hexanedithiol. These crosslinked micelles were pyrolyzed at 600 °C in N₂ to give spherical ceramic particles. The pyrolysis process was examined by thermogravimetry and thermogravimetry/mass spectrometry. The morphologies of the particles were analyzed by atomic force microscopy and transmission electron microscopy. The chemical composition of the pyrolysis products was analyzed by X‐ray fluorescence spectroscopy and Raman scattering spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4696–4707, 2006     

Comprehensive study on the formation of polyelectrolyte complexes from (quaternized) poly[2‐(dimethylamino)ethyl methacrylate] and poly(2‐acrylamido‐2‐methylpropane sodium sulfonate)

Polyelectrolyte complexes (PECs) have been prepared from well‐defined (quaternized) poly[2‐(dimethylamino)ethyl methacrylate] (PDMAEMA) and high molecular weight poly(2‐acrylamido‐2‐methylpropane sodium sulfonate) (PAMPSNa) after a thorough study of their viscometric properties. The effect of pH and quaternization degree of PDMAEMA on PECs stoichiometry has been examined. PEC‐based materials have been characterized in terms of thermal stability, equilibrium swelling degree, and free/bound water composition. The stoichiometry and swellability of the physically crosslinked hydrogels obtained from fully quaternized PDMAEMA/PAMPSNa complexes do not depend on pH. In contrast, PECs made of non quaternized PDMAEMA and PAMPSNa are highly affected by pH, and could reversibly disintegrate at pH ≥ 9. Partially quaternized PDMAEMA/PAMPSNa PECs exhibit intermediate properties and form stable loose structures in the whole investigated pH range. Finally, stable dispersions of PECs nanoparticles have been successfully produced from dilute solutions of the complementary polyelectrolytes. The nanoparticle average diameter as determined by dynamic light scattering proved to depend on the molar fraction of DMAEMA‐based subunits and on the initial polyelectrolyte concentration. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5468–5479, 2006     

Probing the use of small‐angle light scattering for characterizing structure of titanium dioxide/low‐density polyethylene nanocomposites

Small‐angle light scattering (SALS) measurements were used to study the structure of titanium dioxide (TiO₂)/low‐density polyethylene (LDPE) nanocomposites. The results showed that the scattering from LDPE crystalline structures and the scattering from TiO₂ nanoparticles can be resolved and separated. It is shown that the independent effects of crystallization conditions and the presence of nanoparticle aggregates on the spherulitic structure of the LDPE matrix can be determined by analyzing the scattering patterns using the methods proposed. From the SALS results, we conclude that the nanoparticle surface chemistry affects both nucleation of spherulites and their structure particularly under rapid cooling conditions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1084–1095, 2006     

Activity evaluation of carbon paste electrodes loaded with pt nanoparticles prepared in different radiolytic conditions

Three Pt-based catalysts prepared in different radiolytic conditions and supported on graphite powder were packed into a carbon paste electrode configuration. They were compared to each other, to the commercial (Pt) deposited on activated carbon powder (Johnson Matthey) and to pure Vulcan XC-72 for their respective abilities toward the hydrogen evolution reaction (HER). The Tafel parameters were determined for all these electrodes. From the I–V curves and their quantitative treatment, the following order of activity emerged unambiguously and reads: (PtCO)₂ (fcc structure) > (PtCO)₁ (Chini cluster) > (Pt)_neat > (Pt)_JM (Johnson Matthey) ≫ (Vulcan XC-72). As expected, all the Pt-loaded electrodes were more efficient than Vulcan XC-72. The classification appears to be linked with the mean nanoparticle size, and for comparable sizes, with the surface morphology of the materials. The results and the stability of the electrodes suggest that the small particle sizes and the good dispersity on the carbon support were maintained during the HER.     

韧性金属裂纹尖端损伤区内应变场测量——数字散斑相关法应用

本文用数字散斑相关方法测量了五种不同幂硬化指数韧性金属材料(铝和铜),双边裂纹尖端细观区域内应变场.对所得结果用韧性损伤模型进行了分析.在此法中以金属自然表面结构为散斑场,不同加载状态的散斑场进行比较,得到相对变形与应变.图象之间相关性 C 是变形参数或是位移及其导数的泛函.使其相关性 C 取最大值的试凑变形即为其真实变形场.这一方法在细观测量中应用得到满意的结果.     

Overview: The Potential of silanes for chromate replacement in metal finishing industries

Trialkoxysilanes (or silanes) have emerged as a very promising alternative for chromates in metal finishing industries. Compared to the conventional chromating processes, the major merits of silane-based surface treatments include: eco-compliance, easy-control processing, comparable corrosion protection of metals as well as paint adhesion to a variety of topcoats. In this overview paper, we report the recent status of silane studies including results of corrosion performance tests, the mechanism of corrosion protection of metals by silanes and the themal stabilities of silane films. We also address the new fields that we are beginning to explore such as nano-structured silane films, “self-healing” silane films, and “super-primers”.     

Potentiometric studies on the complexation equilibria between some trivalent lanthanide metal ions and biologically active 2-hydroxy-1-naphthaldehyde thiosemicarbazone (HNATS)

Summary The chelation behaviour of some trivalent lanthanide and yttrium metal ion with biologically active 2-hydroxy-1-naphthaldehyde thiosemicarbazone (HNATS) has been investigated by potentiomotric measurements at 20±0.5°C in 75% (v/v) dioxane-water medium at various ionic strengths of sodium perchlorate. The method of Bjerrum and Calvin, as modified by Irving and Rossotti has been used to find out the values of (average number of ligand bound per metal ion) andpL (free ligand exponent). The formation constants of metal chelates have been computed on a PC-XT computer, using a program patterned after that of Sullivan et al. to give _n values using weighted least squares method. TheS _min values (S _min =²) have been calculated. The order of formation constants of chelates was found to be: La³⁺3+3+3+3+3+3+3+3+3+. The formation constants of the chelates formed have been correlated to size and ionization potentials of the metal ions.

---

Potentiometrische Untersuchungen der Komplexierungsgleichgewichte zwischen einigen trivalenten Metallionen und biologisch aktivem 2-Hydroxy-1-naphthaldehyd-thiosemicarbazon (HNATS)

Zusammenfassung Es wurde das Chelierungsverhalten einiger trivalenter Lanthanidenionen mit biologisch aktivem 2-Hydroxy-1-naphthaldehyd-thiosemicarbazon (HNATS) mittels potentiometrischer Messungen bei 20±0.5°C in 75% (v/v) Dioxan-Wasser bei verschiedener Ionenstärke an Natriumperchlorat untersucht. Die Methode nach Bjerrum und Calvin in der Modifikation nach Irving und Rossotti wurde zur Ermittlung der Werte (mittlere Anzahl an Liganden pro Metallion) undpL (Exponent an freiem Liganden) verwendet. Die Komplexbildungskonstanten wurden in Anlehnung an Sullivan et al. an einem PC-XT Computer errechnet. DieS _min-Werte (S _min=²) wurden ebenfalls bestimmt. Die Reihung der Chelatbildungskonstanten war: La³⁺3+3+3+3+3+3+3+3+3+. Die Bildungskonstanten sind mit der Größe und dem Ionisierungspotential der Metallionen zu korrelieren.