Influence of the Interaction between Two Neighboring Periodically Curved Fibers on the Stress Distribution in a Composite Material

A method is developed for a stress analysis in an infinite elastic body containing two neighboring periodically cophasaly curved fibers located along two parallel lines. The stress distribution is studied when the body is loaded at infinity by uniformly distributed normal forces in the fiber direction. The investigation is carried out within the framework of a piecewise homogeneous body model with the use of exact three-dimensional equations of elasticity theory. Numerical results related to the stress distribution considered and the influence of interaction between the fibers on this distribution are given.     

Design and Fabrication of Composite Smart Structures with High Electric and Mechanical Performances for Future Mobile Communication

In this paper, we have developed a load-bearing outer skin for antennas, which is termed a composite smart structure (CSS). The CSS is a multilayer composite sandwich structure in which antenna layers are inserted. A direct-feed stacked patch antenna is considered. A design procedure including the structure design, material selection, and design of antenna elements in order to obtain high electric and mechanical performances is presented. An optimized honeycomb thickness is selected for efficient radiation and impedance characteristics. High gain conditions can be obtained by placing the outer facesheet in the resonance position, which is at about a half wavelength distance from the ground plane. The measured electrical performances show that the CSS has a great bandwidth (over 10%) and a higher gain than an antenna without a facesheet and has excellent mechanical performances, owing to the composite laminates and honeycomb cores. The CSS concept can be extended to give a useful guide for manufacturers of structural body panels and for antenna designers.     

FeCoB-SiO2磁性纳米颗粒膜的微波电磁特性

采用交替沉积磁控溅射工艺制备了超薄多层的FeCoB SiO2 磁性纳米颗粒膜 .利用x射线衍射仪、扫描探针显微镜、透射电子显微镜分析了薄膜的微结构和形貌特征 .采用振动样品磁强计、四探针法、微波矢量分析仪及谐振腔法测量薄膜试样的磁电性能和微波复磁导率 .重点对SiO2 介质相含量、薄膜微结构对电磁性能产生重要影响的机理做了分析和探讨 .结果表明 :这类FeCoB SiO2 磁性纳米颗粒膜具有良好的软磁性能和高频电磁性能 ,2GHz时的磁导率 μ′高于 70 ,可以应用于高频微磁器件或微波吸收材料的设计     

红光激发下掺Ho3+氟化物薄膜的上转换发光

利用激光脉冲沉淀法制备了稀土Ho~(3 )掺杂的氟化物薄膜。观测到处于薄膜中的Ho~(3 )离子在632.8nm红光激发下的上转换发射。这些上转换发射包括:~5S_2→~5I_7,~5F_4→~5I_7和~5S_2→~5I_8。     

热丝加热电流对CH薄膜沉积速率和表面形貌的影响

 热丝辅助裂解法是结合气相沉积制备聚对二甲苯薄膜和热丝化学气相沉积而形成的一种制-CH薄膜的新方法。热丝辅助裂解法的最大特点就是在保持低衬底温度情况下可以获得高沉积速率，而热丝加热电流对薄膜沉积速率和薄膜表面形貌具有重要影响。研究表明，热丝加热电流越大，薄膜沉积速率越高，在加热电流9A时，薄膜沉积速率可达0.002mm/min，同时薄膜表面粗糙度随之增加，薄膜表面也开始出现其它元素污染，因此，一般热丝加热电流选择为7A附近。     

蓝光相变光盘的多层膜结构设计

为了使光盘获得优良的记录／读出性能并能够长期稳定地使用，必须优化设计相变光盘的多层膜结构。采用自行设计的模拟分析相变光盘读出过程设计软件，从光学角度出发模拟计算了蓝光(405nm)相变光盘的膜层结构，研究了多层膜系的反射率和反射率对比度等光学参量与各层膜厚度和槽深的关系。研究得出的最佳多层膜结构为：下介电层／记录层／上介电层／反射层的厚度对于台记录为100nm／10nm／25nm，／60nm，而对于槽记录则为140nm／15nm／30nm，／60nm，槽深为50nm。模拟计算结果对于将来高密度蓝光相变光盘的制备具有一定的指导意义。     

Load-Carrying Capacity of Circular Plates Made of a Fiber-Reinforced Composite

The load-carrying capacity of circular plates made of a fiber-reinforced composite and loaded with axisymmetric transverse forces under axisymmetric boundary conditions is investigated. The plates can be freely supported or clamped along their contour. To the known yield condition used, in the plane of main bending moments, there correspond irregular hexagons, which depend on the mechanical properties of composite constituents and some characteristic geometrical parameters. It is shown that, depending on the ratio of ultimate radial and circumferential bending moments, in the plastic state, the circular plates (the central part of the clamped plates) take the form of a cone or a frustum of cone. For each of the cases, the limit load is found, which is a function of the above-mentioned mechanical parameters. The statically allowable fields of bending moments and the corresponding allowable fields of deflection rates are determined. The solutions found are exact. Special cases for the freely supported plates are analyzed, and the results obtained are presented in the form of graphs.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 177–192, March–April, 2005.     

Photo-induced evolution of copper sheets from cluster molecules and its application to photolithographic copper patterning

UV photoexcitation of (t-butylethynyl copper)₂₄ cluster films induces segregation of the crystals into metallic and organic phases and leads to evolve the metallic sheets sandwiched by organic polymers. The growth of the metallic crystals in the plane of the photo-electromagnetic field is attributed due to plasmon-plasmon interaction among nanoparticles embedded in dielectric polymer matrices. The surface enhanced photochemical reaction of residual cluster molecules on the photon incident direction is expected to take an important role for joining the metal particles to produce a metallic sheet. We can apply this phenomenon for photolithographic copper pattern generation on a flexible base plate.     

集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．