The coexistence of γ(γ′) and θ alumina observed by STM and LEED on top of oxide layer grown on CoAl(1 0 0)

We report the coexistence of γ(γ′) and θ alumina grown on the CoAl(1 0 0) surface. Both phases were observed after annealing of alumina at 1150 K by means of scanning tunnelling microscopy (STM). The crystal structures of γ(γ′) and θ alumina were indexed based on low energy electron diffraction (LEED) and STM experimental data.     

彩色透明微晶玻璃的吸收光谱

在Li2O-Al2O3-SiO2系统玻璃中掺入少量晶核剂TiO2,ZrO2,P2O5，再掺入稀土离子和过渡金属离子作为着色剂，在高温下溶制得到彩色透明玻璃，对上述玻璃进行微晶化处理，用差热分析（DTA）确定其晶化温度，测定与讨论了所获彩色透明微晶玻璃在紫外波段至近红外波段的吸收光谱特性，研究结果表明，玻璃微晶化后，由于基质玻璃对光的微弱散射，引起吸收的增强，但不改变稀土离子和过渡金属离子的本征吸收峰位。     

Optical properties of a high-efficiency glass ceramic X-ray storage phosphor

The turbidity, photoluminescence, and photo-stimulated luminescence (PSL) of fluorozirconate glass containing barium chloride nano- and micro-crystals have been measured for samples prepared by isochronal (70 min) annealing over a temperature range of 220–283°C, and correlated with the microstructure as determined by X-ray diffraction measurements. Crystallization of hexagonal phase barium chloride commences at around 220°C, but until 275°C the material retains excellent transparency although it displays negligible PSL. Between 275°C and 277°C, the hexagonal phase converts to the orthorhombic phase, the transparency abruptly decreases, and the PSL rises to a value of around 13% of that found for the commercial storage phosphor BaFBr:Eu. For a slightly higher temperature of 280°C, new phases appear which correspond to the onset of bulk crystallization, and at 283°C the relative PSL rises to 33%, while the transparency falls further. The trade-off between optical transparency and PSL over this narrow temperature window for X-ray imaging plate applications is briefly discussed.     

压电陶瓷压电特性的激光调制法测量研究

介绍可测量压电陶瓷压电特性的激光干涉调制测量方法.采用相干检测原理对信号进行提取,不仅可以抑制噪声对干涉信号的影响,而且还可以大大降低光电探测器和电路的1/f噪声.与通常干涉仪测量方法相比,这种方法具有测量灵敏度高等优点.利用该方法对压电陶瓷压电特性进行了测量,讨论了激励电压信号的频率、幅度对压电陶瓷压电常数d₃₁的影响,并对其压电迟滞曲线进行了测量.     

A Novel Method to Synthesize Polyorganozircosilazane

A new kind of polyorganozircosilazane as Si/Zr/C/N-based ceramic precursor was synthesized from the condensation reaction of hexamethyleyclotrisilazane lithium salts(D3^NLi）and zirconium tetrachloride(ZrCl4).In the presence of N,N,N’,N’-tetramethyl ethylene diamine(TMEDA),polyorganozircosilazane was obtained in high yield.     

甲醇与乙醇一步合成异丁醛用CuO-ZnO/Al2O3催化剂

在ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３催化剂上，甲醇与乙醇在常压和２１０￣３６０℃温度下一步反应合成异丁醛。利用正交设计方法，研究了ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３体系催化剂组成和制备条件等因素对催化剂催化性能的影响。结果表明，催化剂中ＣｕＯ含量对催化剂的催化活性影响最大，而ＺｎＯ含量则主要影响催化剂对异丁醛的选择性。催化剂制备条件，如沉淀温度、陈化时间等，也不同程度也影响催化剂的催化性能。ＸＲＤ和ＢＥＴ表征结果     

γ-Al2O3对NiB合金的催化及表面性能的影响

集），Dalian（大连）：1994，p.262||8LiuWeicheng（刘伟成），YanJingqing（晏荆青），JiangBingnan（姜炳南）．CuihuaXuebao（催化学报），1990，||11（2）：929HuCW，WangWZXuGY，etal．J．Nat．GasChem，1994,（3）：194||     

Mesoporous electrode material from alumina-stabilized anatase TiO2 for lithium ion batteries

A mesoporous electrode material whose structure is composed of anatase nanocrystals stabilized by alumina is reported. Powder X-ray diffraction shows the anatase phase only, but micro-Raman spectroscopy shows that the materials have a core-shell morphology with grains of bulk anatase covered by a thin rutile layer on the surface. This structure is unique when compared to analogous materials stabilized by zirconia (PNNL-1). Nitrogen adsorption isotherms demonstrate a monotonous increase in surface area and mesopore volume with increasing Al content. Thin film electrodes from these materials were characterized by lithium insertion electrochemistry. Cyclic voltammograms exhibit significant differences in Li accommodation in Al-free and Al-stabilized materials.     

Determination of cake thickness and porosity during cross-flow ultrafiltration on a plane ceramic membrane surface using an electrochemical method

The thickness and the porosity of a deposit during ultrafiltration experiments are determined using an electrochemical method. Twenty microelectrodes are mounted flush to a ceramic plane membrane and maps of deposit thickness are determined for three inlet/outlet distributors configurations. Combining an electrochemical method and a step transient method, the determination of the thickness and the porosity of a particles deposit is performed. These local thickness and porosity values are analyzed thanks to wall shear stress local measurements obtained in a previous work [Sep. Sci. Technol. 37 (10) (2002) 2251]. The results emphasize the heterogeneity of the deposit thickness, especially in zones of low wall shear stress. Furthermore, the porosity values of the deposit are ranged between 0.3 and 0.8 as a function of the location at the membrane surface.