Viscosity,particle size distribution,and structural investigation of tetramethyloxysilane/2‐hydroxyethyl methacrylate sols during the sol–gel process with acid and base catalysts

The tetramethoxysilane (TMOS)/2‐hydroxylethyl methacrylate (HEMA) hybrid gels were synthesized with acid and base catalysts, via the in situ polymerization of HEMA, with and without the cosolvent methanol. With methanol in the TMOS/HEMA sol, the enhanced esterification and depolymerization reactions of the silanols resulted in a slower growth of silica particles. The silica particles that were synthesized with an acid catalyst were less than 40 nm. The thermal resistance of the poly(2‐hydroxyethyl methacrylate) (PHEMA) chains was enhanced by the addition of colloidal silica. The Fourier transform infrared characterizations and the exothermal peaks on the differential scanning calorimetry traces of these hybrid gels indicated chemical hybridization occurring as a result of condensation of the colloid silica and PHEMA at higher temperatures. Hence, the residual weight content of the hybrid gel after its synthesis with the base catalyst was even higher than the content of TMOS in the hybrid sol. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3476–3486, 2004     

Estimation of kinetics parameters for the adsorption of human serum albumin onto hydroxyapatite-modified silver electrodes by piezoelectric quartz crystal impedance analysis.

The adsorption of human serum albumin onto hydroxyapatite-modified silver electrodes has been in situ investigated by utilizing the piezoelectric quartz crystal impedance technique. The changes of equivalent circuit parameters were used to interpret the adsorption process. A kinetic model of two consecutive steps was derived to describe the process and compared with a first-order kinetic model by using residual analysis. The experimental data of frequency shift fitted to the model and kinetics parameters, k1, k2, psi1, psi2 and qr, were obtained. All fitted results were in reasonable agreement with the corresponding experimental results. Two adsorption constants (7.19 kJ mol(-1) and 22.89 kJ mol(-1)) were calculated according to the Arrhenius formula.     

螺旋线径向挤压变形对其慢波结构冷测特性的影响

 介绍了用MAFIA软件的准周期边界条件计算螺旋线行波管慢波结构的色散和耦合阻抗，以及用ANSYS软件对螺旋线径向挤压变形建模的方法，并对螺旋线受挤压径向变形对其冷测特性的影响进行了详细的分析。结果表明:螺旋线径向挤压变形会导致相速增大，而在通常的变形范围内耦合阻抗也会增加；当变形继续增大时耦合阻抗上升到最大值后开始下降。     

激光限制结晶技术制备nc-Si/SiO2多层膜

在等离子体增强化学气相淀积系统中，采用aSi:H层淀积和原位等离子体氧化相结合的逐层生长技术制备了aSi:H/SiO_2多层膜.在激光诱导限制结晶原理基础上，使用KrF准分子脉冲激光为辐照源，对aSi:H/SiO_2多层膜进行辐照，使纳米级厚度的aSi:H子层晶化.Raman散射谱和电子衍射谱的结果表明，经过激光辐照后纳米Si颗粒在原始的aSi:H子层内形成，晶粒尺寸可以根据aSi:H层的厚度精确控制.还研究了样品的光致发光（PL）特性以及激光辐照能量密度对PL性质的影响. 关键词： 脉冲激光 多层膜 限制结晶     

ns脉冲激光对K9玻璃的破坏实验

 采用高速PIN光电探测器和高带宽的数字存储示波器，实时检测透射光脉冲和散射光脉冲的变化特征，并将之用作材料破坏的光学判据，测量得到K9玻璃在1.06μm纳秒脉冲激光作用下的能量损伤阈值约18mJ，相应的能量密度阈值为1.0kJ/cm²。通过分析透射光脉冲和散射光脉冲的特征，给出了材料的破坏时刻，并推断出K9玻璃所能承受的极限光强为10¹⁵W/m²。研究了能量透过率与泵浦能量的关系，并初步探讨了透明材料的破坏机理。结果表明：在多纵模激光的作用下，透明光学材料破坏是电离击穿与自聚焦效应综合作用的结果。     

连续照明时成像对比度与气象条件的关系

 通过同轴激光连续照明成像模型分析了大气后向散射对成像对比度的影响，得出了考虑散射因素时成像对比度的计算公式。基于不同气象条件下大气粒子散射特点，讨论了霾和雾两种不同天气时成像对比度随照明距离的变化规律，并与实验结果进行了对比，计算结果与实验吻合较好。     

利用爆磁压缩发生器产生高功率脉冲高电压

 爆磁压缩发生器产生脉冲高电压技术可以用于产生高功率微波及强电磁脉冲的实验研究。给出了利用螺旋型爆磁压缩发生器（HEMG）驱动电爆炸丝功率调节系统产生高功率脉冲高电压的实验方法和主要的结果。在利用HEMG驱动电爆炸丝断路开关（EEOS）产生脉冲高电压实验中，获得了最高电压700~800kV,功率大于20GW的脉冲输出。     

超短脉冲超强激光与固体靶相互作用中高能离子的产生

 用2D3V PIC粒子模拟方法得到了超短脉冲超强激光与固体靶相互作用中高能离子产生的图像，并对其机理进行了研究。在靶前后表面都观察到了高能离子的产生，并诊断了离子能谱。模拟结果表明，在靶前表面所产生的高能离子，角分布较大，在向靶内输运过程中会损失能量；在靶后表面产生的高能离子，定向性很好，能获得很高的能量。模拟得到的离子能量和实验观测结果在量级上相符。     

行波管内不连续性的简易模型分析

 根据行波管内微波信号在输能装置和切断衰减器处两个不连续性之间来回反射的物理现象，建立行波管输出段的简易网络串模型，并对行波管输出段传输特性参数的幅频特性、相频特性进行计算分析。结果表明：输能装置和切断衰减器的不连续性是造成幅相一致性行波管相位不可补偿的重要因素之一。     

The Research on Polymer Microcapsulation for Cell Technology

Microcapsulation is a technology that enwrapped the solid or liquid or some gas matter with membrane materials to form microparticles(i.e.microcapsules). The materials of microcapsule is composed of naturnal polymers or modified naturnal polymers or synthesized polymers. The water-soluble core matter can only use oil-soluble wall materials, and vice versa.Synthesized methods of polymer microcapsulesSynthesized methods with monomers as raw materialsThis kind of methods include suspension polymerization, emulsion polymerization, dispersal polymerization, precipitation polymerization,suspension condensation polymerization, dispersal condensation polymerization, deposition condensation polymerization, interface condensation polymerization, and so on.Synthesized methods with polymers as raw materialsThese methods are suspension cross-linked polymerization, coacervation phase separation,extraction with solvent evaporation, polymer deposition, polymer chelation, polymer gel,solidification of melting polymer, tray-painted ways, fluidized bed ways, and so forth.Polymer materials to synthesize microcapsules2.1. Naturnal polymer materialsThe characteristics of this kind of materials are easy to form membrane, good stability and no toxicity. The polymer materials include lipids(liposome), amyloses, proteins, plant gels, waxes, etc.2.2. Modified polymer materialsThe characteristics of these materials are little toxicity, high viscidity(viscosity), soluble salt materials. But they cannot be used in water, acidic environment and high temperature environment for a long time. The materials include all kind of derivants of celluloses.2.3. Synthesized polymer materialsThe characteristics of the materials are easy to form membrane, good stability and adjustment of membrane properties. The synthesized polymer materials include degradable polymers(PLA, PGA,PLGA, PCL, PHB, PHV, PHA, PEG, PPG and the like) and indegradable polymers(PA, PMMA,PAM, PS, PVC, PB, PE, PU, PUA, PVA and otherwise).The applications of polymer microcapsules in cell technologyThe "artificial cell" is the biological active microcapsule used in biological and medical fields.The applications of cells (including transgenic cells, the same as artificial cells) technology include several aspects as follows:3.1. Microcapsulation of artificial red cell3.2. Microcapsule of artificial cell of biological enzyme3.3. Microcapsule of artificial cell of magnetic material3.4. Microcapsule of artificial cell of active carbon3.5. Microcapsule of active biological cell