GZO/Al复合背电极对非晶硅太阳能电池的影响

随着能源紧缺与环境污染问题的日益严重,太阳能的开发利用越来越受到重视,其中非晶硅薄膜太阳能电池由于其制备工艺简单、价格低廉等优点被广泛地研究.为了使非晶硅薄膜太阳能电池得到更好地利用,提高其转换效率和稳定性显得尤为重要.引入复合背电极是提高非晶硅太阳能电池性能的有效手段,其中对GZO/Al复合背电极的研究还未见报道.在该工作中,利用磁控溅射法在非晶硅电池上制备了GZO/Al复合背电极,研究了复合背电极的制备条件及其对非晶硅太阳能电池性能的影响.结果显示,当GZO层的溅射功率为90 W、Al层的溅射功率为90 W时,具有复合背电极的太阳能电池表现出较好的光电转换性能,其短路电流(ISC)、开路电压(VOC)、填充因子(FF)和电池的光电转换效率(η)分别为8.92 mA、1.55 V、54.48;和7.53;.相较于单层Al背电极的太阳能电池,其光电转换效率大幅提高了47.6;(相对效率).     

Polypyrrole Shell@3D‐Ni Metal Core Structured Electrodes for High‐Performance Supercapacitors

Three‐dimensional (3D) nanometal films serving as current collectors have attracted much interest recently owing to their promising application in high‐performance supercapacitors. In the process of the electrochemical reaction, the 3D structure can provide a short diffusion path for fast ion transport, and the highly conductive nanometal may serve as a backbone for facile electron transfer. In this work, a novel polypyrrole (PPy) shell@3D‐Ni‐core composite is developed to enhance the electrochemical performance of conventional PPy. With the introduction of a Ni metal core, the as‐prepared material exhibits a high specific capacitance (726 F g^?1 at a charge/discharge rate of 1 A g^?1), good rate capability (a decay of 33 % in C_sp with charge/discharge rates increasing from 1 to 20 A g^?1), and high cycle stability (only a small decrease of 4.2 % in C_sp after 1000 cycles at a scan rate of 100 mV s^?1). Furthermore, an aqueous symmetric supercapacitor device is fabricated by using the as‐prepared composite as electrodes; the device demonstrates a high energy density (≈21.2 Wh kg^?1) and superior long‐term cycle ability (only 4.4 % and 18.6 % loss in C_sp after 2000 and 5000 cycles, respectively).     

某型电动飞机螺旋桨振动特性实验研究

某型电动飞机采用螺旋桨产生拉力,为了防止螺旋桨工作时共振,利用ES-2-150振动实验系统进行了两叶木质螺旋桨和碳纤维螺旋桨的振动特性实验,采用谐振搜索与驻留方法测量出木质螺旋桨的第一阶固有频率为36.07Hz,碳纤维螺旋桨的第一阶固有频率为73.58Hz。螺旋桨爬升状态转频为39Hz,这与木质螺旋桨的第一阶固有频率非常接近,导致木质螺旋桨在爬升状态出现比较严重的振动故障。因此,某型电动飞机最终选择两叶碳纤维螺旋桨作为其拉力产生装置。     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．     

Physicochemical properties and bio-interfacial interactions of surface modified PDLLA-PAMAM linear dendritic block copolymers

Here, we demonstrate the applicability of self-assembling linear-dendritic block copolymers (LDBCs) and their nanoaggregates possessing varied surfaces as therapeutic nanocarriers. These LDBCs are comprised of a hydrophobic, linear polyester chemically coupled to a hydrophilic dendron polyamidoamine (PAMAM)—the latter of which acts as the surface of the self-assembled nanoaggregate in aqueous media. To better understand how surface charge density affects the overall operability of these nanomaterials, we modified the nanoaggregate surface to yield cationic (NH₃⁺), neutral (OH), and anionic (COO⁻) surfaces. The effect of these modifications on the physicochemical properties (i.e., size, morphology, and surface charge density), colloidal stability, and cellular uptake mechanism of the polymeric nanocarrier were investigated. This comparative study demonstrates the viability of nanoaggregates formed from PDLLA-PAMAM LDBCs to serve as nanocarriers for applications in drug delivery.     

基于深度学习的ELM实时识别研究

基于深度学习的方法，在HL-2A装置上开发出了一套边缘局域模(ELM)实时识别算法。算法使用5200次放电数据(约24.19万数据切片)进行学习，得到一个深度为22层的卷积神经网络。为衡量算法的识别能力，识别了HL-2A装置自2009年实现稳定ELMy H模放电以来所有历史数据(约26000次放电数据)，共识别出1665次H模放电，其中误识别35次，误报率为2.10%。在实际的1634次H模放电中，漏识别4次，漏识别率为0.24%。该误报率和漏报率可以满足ELM实时识别的精度要求。识别算法在实时控制环境下，对单个时间点的平均计算时间为0.46ms，可以满足实时控制的计算速度要求。     

基于时变Copula模型的 基金收益率相依关系的应用研究

基于时变Copula模型,获得预测方差,确定单个基金收益率序列的边缘分布.利用常见的静态Copula和时变Copula模型对基金收益率序列间两两相依关系进行建模并进行对比分析.应用研究表明,基于MCMC方法的时变Copula模型能更有效地度量基金收益率序列的风险.     

Investigation of mononuclear,dinuclear, and trinuclear transition metal (II) complexes derived from an asymmetric Salamo‐based ligand possessing three different coordination modes

A new asymmetric Salamo‐based ligand H₂L was synthesized using 3‐tert‐butyl‐salicylaldehyde and 6‐methoxy‐2‐[O‐(1‐ethyloxyamide)]‐oxime‐1‐phenol. By adjusting the ratio of the ligand H₂L and Cu (II), Co (II), and Ni (II) ions, mononuclear, dinuclear, and trinuclear transition metal (II) complexes, [Cu(L)], [{Co(L)}₂], and [{Ni(L)(CH₃COO)(CH₃CH₂OH)}₂Ni] with the ligand H₂L possessing completely different coordination modes were obtained, respectively. The optical spectra of ligand H₂L and its Cu (II), Co (II) and Ni (II) complexes were investigated. The Cu (II) complex is a mononuclear structure, and the Cu (II) atom is tetracoordinated to form a planar quadrilateral structure. The Co (II) complex is dinuclear, and the two Co (II) atoms are pentacoordinated and have coordination geometries of distorted triangular bipyramid. The Ni (II) complex is a trinuclear structure, and the terminal and central Ni (II) atoms are all hexacoordinated, forming distorted octahedral geometries. Furthermore, optical properties including UV–Vis, IR, and fluorescence of the Cu (II), Co (II), and Ni (II) complexes were investigated. Finally, the antibacterial activities of the Cu (II), Co (II), and Ni (II) complexes were explored. According to the experimental results, the inhibitory effect was found to be enhanced with increasing concentrations of the Cu (II), Co (II), and Ni (II) complexes.     

激光能量对反钙钛矿GaCMn_3薄膜结构与物性的影响

本文采用脉冲激光沉积方法在LaAlO3(001)单晶衬底上制备了反钙钛矿GaCMn3薄膜,通过控制制备过程中脉冲激光的能量,研究了不同激光能量条件对GaCMn3薄膜结构与物理性能的影响.分别利用X射线衍射仪、原子力显微镜、超导量子干涉仪和物理性能测试系统,对所制备的薄膜的晶体结构、表面形貌和磁性、电输运性质进行了研究.结果表明,制备的样品均为具有多个晶面取向的反钙钛矿薄膜,且薄膜结构和物性明显随制备激光能量的变化而变化.当激光能量为450mJ时,制备的薄膜多晶面取向性最弱,结晶性和表面形貌最优良.实验所得的薄膜均表现出顺磁-铁磁-反铁磁相转变,然而转变过程比块材较平缓,同时薄膜的电阻率并未表现出块材中的突变特征,我们推测该现象很可能是由衬底的应力及衬底的晶格膨胀对薄膜反常晶格变化的抑制作用造成的.     

QEPAS系统中石英音叉模态仿真计算与研究

对石英音叉增强型光声光谱(QEPAS)系统中常用的石英音叉进行了有限元模态计算，获得石英音叉前6阶振型与模态频率，认知了第4阶对称摆动振型为有效振动，利用单因素法分析了石英音叉的音臂长度l₁、音臂宽度w₁、音臂厚度t、音臂切角θ、音臂圆孔直径d及音臂圆孔高度h对低阶有效共振频率(Fre)的影响，敏感度依次为： l₁> w₁>d>θ>t>h，考虑实际设计情形，筛选出了l₁，w₁，d与h四个石英音叉设计变量，采用Box-Behnken实验设计方案与RSM(response surface methodology)方法，以Fre为函数目标，建立l₁，w₁，d与h的二次回归响应面模型，得到了参数之间的交互作用，利用Design-Expert软件对响应面模型进行设计参数反求，结果表明，在15 000 Hz≤Fre≤25 000 Hz计算区域内误差较小，基本满足QEPAS系统的计算需求，所提出的研究与设计方法具有一定通用性，可为QEPAS系统中石英音叉结构参数设计提供参考。