液相色谱-串联质谱法测定桃中31种农药残留

取均质后的桃皮或桃肉,在匀浆机上用乙腈提取;加入氯化钠及硫酸镁振荡盐析;取上清液与PSA混匀并离心进行净化。取经滤膜过滤的滤液与水混匀后供液相色谱-串联质谱分析。用Agilent Eclipse plus C18 RRHT色谱柱为分离柱,用含甲酸的5mmol·L-1甲酸铵溶液与乙腈以不同比例的混合液作流动相进行梯度淋洗。质谱测定中采用电喷雾正离子源动态多反应监测模式进行检测。所测31种农药在一定质量分数范围内保持线性关系,方法的检出限(3S/N)在0.04~20μg·kg-1之间,回收率在73.6%~119%之间,测定值的相对标准偏差(n=6)在0.70%~17%之间。     

基于脉冲微反装置的Au/HZSM-5催化剂上正丁烷反应性能研究

以HZSM-5沸石分子筛为载体,尿素为沉淀剂,采用常压沉积-沉淀法和负压沉积-沉淀法制备了系列Au/HZSM-5沸石催化剂并采用常规催化剂表征方法对其进行了表征.用脉冲微反装置评价了纯正丁烷(99.9%)在氢型和金改性的纳米HZSM-5催化剂上的反应活性和烯烃选择性.结果表明,在550℃下,负压沉积-沉淀法制备的不同金负载量的纳米HZSM-5催化剂上的转化率和烯烃选择性都远高于常压沉积沉淀法制备的催化剂.改性量为2.0%的Au/HZSM-5-A(负压)催化剂正丁烷转化率达到了58.0%、烯烃选择性为57.2%.脱氢和脱甲基活化是正丁烷的重要活化方式,也是影响其烯烃选择性的主要因素.金改性在提高正丁烷转化率的同时,也促进了正丁烷的脱氢和脱甲基活化.纳米HZSM-5因晶粒度小,孔道短和微孔扩散阻力低而有利于正丁烷转化.负压有利于清除HZSM-5内部的无定型杂质和脱气净化处理,有利于金的负载量和分散度.     

固相萃取/超高效液相色谱-串联质谱法测定化妆品中12种合成着色剂

建立了固相萃取/超高效液相色谱-串联质谱法(SPE/UPLC-MS/MS)同时测定指甲油、眼影、唇膏等化妆品中12种合成着色剂(酸性紫49、颜料红57、颜料红53∶1、酸性黄36、结晶紫、罗丹明B、分散黄3、颜料橙5、苏丹红Ⅰ、苏丹红Ⅱ、苏丹红Ⅳ和溶剂蓝35)的分析方法。样品用四氢呋喃(THF)、二甲基亚砜(DMSO)和甲醇分步超声波辅助萃取,HLB固相萃取柱净化后,在Acquity UPLC BEH-C18(2.1 mm×50mm,1.7μm)色谱柱上分离,乙腈和0.05%甲酸溶液为流动相梯度洗脱,采用多反应监测(MRM)模式进行检测,基质外标法定量。结果表明:12种着色剂在6 min内均显示较好峰形,其线性范围为0.5~800μg·L-1,相关系数均大于0.99。定量下限(LOQ,S/N10)为1.4~2 000μg·kg-1。在指甲油、眼影和唇膏中分别添加0.025~20 mg·kg-1浓度的着色剂进行加标回收实验,测定回收率为60.8%~118.0%,相对标准偏差(RSD)为2.3%~10.8%。该方法快速、简便、灵敏,适用于油状、粉状及膏状化妆品中禁限用着色剂的定量和确证分析。     

液相色谱-串联质谱法测定人参中申嗪霉素的残留

建立了液相色谱-电喷雾串联质谱测定人参中申嗪霉素残留量的分析方法。人参样品经水浸泡,乙腈提取,分散固相萃取净化,色谱分离后,采用ESI-MS/MS在正离子多反应监测(MRM)模式下进行检测,选择定量离子对为m/z 225.1/179.1,定性离子对为m/z 225.1/125.1,外标法定量。该方法对于人参中申嗪霉素的定量下限为0.01 mg/kg,在0.5~10μg/L质量浓度范围内,峰面积与含量呈良好线性关系,相关系数大于0.99。对人参中申嗪霉素在0.01,0.02,0.10 mg/kg加标水平下的回收率为82%~100%,相对标准偏差均不大于6.8%。结果表明,该方法操作简单、快速,灵敏度和准确度高,可满足人参中申嗪霉素残留量的检测要求。     

高效液相色谱-电喷雾串联质谱法测定畜禽粪便中四环素类抗生素

建立了高效液相色谱-电喷雾串联质谱法(HPLC-MS/MS)测定畜禽粪便中四环素类抗生素的分析方法。样品经甲醇-乙酸-水(体积比6∶3∶1)溶液提取,OASIS HLB小柱净化后,采用Waters Symmetry C18色谱柱(150×3.9mm,5μm)进行分离,以0.3%甲酸水溶液-0.3%甲酸乙腈溶液梯度洗脱,电喷雾正离子模式多反应监测(MRM)模式定量分析。在优化的色谱条件下,四环素、土霉素和金霉素在0.05~1.0mg/L范围内具有良好的线性,其检出限分别为0.025、0.084、0.098mg/kg;样品回收率为80%~103%。实验结果表明,该方法较液相色谱法具有更高的准确性和灵敏度,可满足畜禽粪便中四环素类抗生素残留的检测要求。     

焙烧温度对1,4-丁烯二醇加氢Cu/Raney-Ni催化剂结构和性能影响

在Ni-Al合金粉上浸渍硝酸铜溶液,经不同温度焙烧得到Cu改性Ni-Al合金粉,采用质量分数10%NaOH溶液浸渍上述改性合金粉得Cu/Raney-Ni催化剂。采用EDX、XRD、N_2吸附-脱附、TEM和NH_3-TPD等手段表征了Ni-Al合金粉及相应Raney-Ni催化剂的元素含量、晶体结构、孔结构特征、表面形貌和表面酸碱性,并以1,4-丁烯二醇加氢制1,4-丁二醇为探针反应,考察了焙烧温度对Raney-Ni催化剂加氢性能的影响。表征分析表明,焙烧温度500℃所制备的CRT500催化剂比表面积较大,为64.96m~2/g;弱酸中心比例较高,达81.2%。结果表明,焙烧温度升高,BED可实现完全转化,BDO选择性和收率均先升高后降低。其中,CRT500加氢性能较好,BED转化率为100.00%,BDO选择性为61.88%。进一步升高焙烧温度,催化剂RCT550和RCT600的BDO选择性和收率反而降低,这是由于高温下催化剂易发生团聚或烧结。结合催化剂表征可知,CRT500具有较好的加氢性能,这与该催化剂具有合适的Ni/Al物质的量比(3.84)、弱酸中心所占比例较大和活性组分Ni分散性好等因素有较大关联。     

北京大学分析化学系列小班阅读讨论课的教学实践

简介了北京大学化学与分子工程学院分析化学系列基础课(定量分析化学、仪器分析、中级分析化学)开展小班阅读讨论课教学的实践。     

De Novo Construction of Catenanes with Dissymmetric Cages by Space‐Discriminative Post‐Assembly Modification

Considerable efforts have been made to increase the topological complexity of mechanically interlocked molecules over the years. Three‐dimensional catenated structures composed of two or several (usually symmetrical) cages are one representative example. However, owing to the lack of an efficient universal synthetic strategy, interlocked structures made up of dissymmetric cages are relatively rare. Since the space volume of the inner cavity of an interlocked structure is smaller than that outside it, we developed a novel synthetic approach with the voluminous reductant NaBH(OAc)₃ that discriminates this space difference, and therefore selectively reduces the outer surface of a catenated dimer composed of two symmetric cages, thus yielding the corresponding catenane with dissymmetric cages. Insight into the template effect that facilitates the catenation of cages was provided by computational and experimental techniques.     

Chemical modification of carbon fiber with diethylenetriaminepentaacetic acid/halloysite nanotube as a multifunctional interfacial reinforcement for silicone resin composites

In the present research, a multifunctional hierarchical reinforcement was prepared by chemical modification of carbon fibers (CFs) with halloysite nanotubes (HNTs) by the bridging diethylenetriaminepentaacetic acid (DTPA) for improving interfacial microstructures and properties of composites. Surface structures and groups of modified HNTs and CFs were characterized systematically. The uniform distributions of the introduced DTPA and HNTs helped to increase fiber polarity, surface energy, and wettability. As a consequence, significant enhancements of interfacial properties and hydrothermal aging resistance of composites were achieved, and interfacial reinforcing mechanisms have also been studied. Moreover, the storage modulus showed a 17.95% improvement, and the glass transition temperature was enhanced by 17°C by dynamic mechanical analysis testing.     

Systematic Research and Evaluation Models of Nanomotors for Cancer Combined Therapy

Limited tumor permeability of therapeutic agents is a great challenge faced by current cancer therapy methods. Herein, a kind of near infrared light (NIR)‐driven nanomotor with autonomous movement, targeted ability, hierarchical porous structure, multi‐drugs for cancer chemo/photothermal therapy is designed, prepared and characterized. Further, we establish a method to study the interaction between nanomotors and cells, along with their tumor permeability mechanism, including 2D cellular models, 3D multicellular tumor spheroids and in vivo models. In vivo tumor elimination results verify that the movement behaviour of the nanomotors can greatly facilitate them to eliminate tumor through multiple therapeutic methods. This work tries to establish systematic research and evaluation models, providing strategies to understand the relationship between motion behaviour and tumor permeation efficiency of nanomotors in depth.