Na原子链表面等离激元特性的含时密度泛函研究

本文用含时密度泛函理论研究了线性Na原子链的表面等离激元机理.主要在原子尺度下模拟计算了体系随着原子数增加及原子间距变化的集体激发过程.研究发现线性原子链有一个普遍的特性——存在一个纵模和两个横模.两个横模一般在实验上很难被观测到.纵模随着原子链长度增加,能量红移的同时,该纵模主峰的强度呈线性增长.随着原子个数的增加,端点模式(TE)开始蓝移,能量和偶极强度都逐渐趋向饱和.横模能量被劈裂的原因概括如下:(一)每个位置的电子受到的势不同,在两端的电子受到的势要比在中间的电子受到的势要高,因此两端的电荷积累也比中间多;(二)端点存在悬挂键,所以中间的电子-电子间相互作用与端点的不一样,这两方面又都与原子间距d有关.     

Single-emissive-layer all-perovskite white light-emitting diodes employing segregated mixed halide perovskite crystals

Metal halide perovskites have demonstrated impressive properties for achieving efficient monochromatic light-emitting diodes. However, the development of white perovskite light-emitting diodes (PeLEDs) remains a big challenge. Here, we demonstrate a single-emissive-layer all-perovskite white PeLED using a mixed halide perovskite film as the emissive layer. The perovskite film consists of separated mixed halide perovskite phases with blue and red emissions, which are beneficial for suppressing halide anion exchange and preventing charge transfer. As a result, the white PeLED shows balanced white light emission with Commission Internationale de L''Eclairage coordinates of (0.33, 0.33). In addition, we find that the achievement of white light emission from mixed halide perovskites strongly depends on effective modulation of the halide salt precursors, especially lead bromide and benzamidine hydrochloride in our case. Our work provides very useful guidelines for realizing single-emissive-layer all-perovskite white PeLEDs based on mixed halide perovskites, which will spur the development of high-performance white PeLEDs.

We demonstrated a single-emissive-layer all-perovskite white light-emitting diode based on a mixed halide perovskite film.     

(111)择优取向ZnS薄膜的制备及特性研究

采用激光分子束外延技术在Al2O3衬底上成功外延生长了ZnS薄膜.用X射线衍射、扫描电子显微镜和光致发光谱表征了衬底温度对薄膜结构、形貌和光学特性的影响.结果表明所生长的ZnS薄膜为闪锌矿,具有(111)择优长向,随衬底温度的升高,X射线衍射峰的半高宽先减小后增大,在衬底温度为300℃时,半高宽最窄.薄膜结构致密,表面不平整度随衬底温度的升高而增大.薄膜的带隙随衬底温度的升高出现蓝移,可见光区域透射率最高达到98;,在360 nm激发波长下,观测到402 nm和468 nm两个发光带,衬底温度为300℃时,发光最强.     

Fluid‐structure coupling of linear elastic model with compressible flow models

Cavitation erosion is caused in solids exposed to strong pressure waves developing in an adjacent fluid field. The knowledge of the transient distribution of stresses in the solid is important to understand the cause of damaging by comparisons with breaking points of the material. The modeling of this problem requires the coupling of the models for the fluid and the solid. For this purpose, we use a strategy based on the solution of coupled Riemann problems that has been originally developed for the coupling of 2 fluids. This concept is exemplified for the coupling of a linear elastic structure with an ideal gas. The coupling procedure relies on the solution of a nonlinear equation. Existence and uniqueness of the solution is proven. The coupling conditions are validated by means of quasi‐1D problems for which an explicit solution can be determined. For a more realistic scenario, a 2D application is considered where in a compressible single fluid, a hot gas bubble at low pressure collapses in a cold gas at high pressure near an adjacent structure.     

Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Identifying the viscoelastic properties of soft matter from the indentation response of a hard film-soft substrate system

The indentation technique is widely used in measuring the mechanical properties of soft matter at the microscale or nanoscale,but still faces challenges by these unique properties as well as the consequent strong surface adhesion, including the strong nonlinear effect, unclear judgment of the contact point, difficulties in estimating the contact area, and the risk of the indenter piercing the sample. Here we propose a two-step method to solve these problems: lay a hard film on a soft matter, and obtain the viscoelastic properties of this soft matter through the indentation response of this composite structure. We first establish a theoretical indentation model of the hard film-soft substrate system based on the theory of plates, elastic-viscoelastic correspondence principle and Boltzmann superposition principle. To verify the correctness of this method, we measure the mechanical properties of the methyl vinyl silicone rubber(MVSR) covered by a Cu nanofilm. Finally, we test the effectiveness and error sensitivity of this method with the finite element method(FEM). The results show that our method can accurately measure the mechanical properties of soft matter, while effectively circumventing the problems of the traditional indentation technique.