Low-temperature destruction of carbon tetrachloride over lanthanide oxide-based catalysts: from destructive adsorption to a catalytic reaction cycle

The catalytic destruction of carbon tetrachloride in the presence of steam, CCl(4) + 2 H(2)O-->4 HCl + CO(2), was investigated at 200-350 degrees C over a series of lanthanide (La, Ce, Pr and Nd) and alkaline-earth metal (Mg, Ca, Sr and Ba) oxide-based catalysts with kinetic experiments, Raman spectroscopy, X-ray photoelectron spectroscopy, IR spectroscopy, X-ray diffraction, and DFT calculations. This new catalytic reaction was achieved by combining destructive adsorption of CCl(4) on a basic oxide surface and concurrent dechlorination of the resulting partially chlorinated solid by steam. The combination of the two noncatalytic reactions into a catalytic cycle provided a rare opportunity in heterogeneous catalysis for studying the nature and extent of surface participation in the overall reaction chemistry. The reaction is proposed to proceed over a terminal lattice oxygen site with stepwise donation of chlorine atoms from the hydrocarbon to the surface and formation of the gas-phase intermediate COCl(2), which is readily readsorbed at the catalyst surface to form CO(2). In a second step, the active catalyst surface is regenerated by steam with formation of gas-phase HCl. Depending on the reaction conditions, the catalytic material was found to transform dynamically from the metal oxide state to the metal oxide chloride or metal chloride state due to the bulk diffusion of oxygen and chlorine atoms. A catalyst obtained from a 10 wt % La(2)O(3)/Al(2)O(3) precursor exhibited the highest destruction rate: 0.289 g CCl(4) h(-1) g(-1) catalyst at 350 degrees C, which is higher than that of any other reported catalyst system.     

Single molecule spectroscopy as a probe for dye-polymer interactions

Experimental (Single Molecule Spectroscopy) and theoretical (quantum-chemical calculations and Monte Carlo and molecular dynamics simulations) techniques are combined to investigate the behavior and dynamics of a polymer-dye molecule system. It is shown that the dye molecule of interest (1,1'-dioctadecyl-3,3,3',3'-tetramethylindo-dicarbocyanine) adopts two classes of conformations, namely planar and nonplanar ones, when embedded in a poly(styrene) matrix. From an in-depth analysis of the fluorescence lifetime trajectories, the planar conformers can be further classified according to the way their alkyl side chains interact with the surrounding poly(styrene) chains.     

Computational Fluid Dynamic Design of Jet Stirred Reactors for Measuring Intrinsic Kinetics of Gas‐Phase and Gas‐Solid Reactions

Nonreactive and reactive computational fluid dynamic simulations were applied to optimize the design of a laboratory scale jet stirred reactor for measuring intrinsic kinetics of gas‐phase and gas‐solid reactions, i.e. kinetics determined by chemical steps only and not by heat or mass transfer. In the past these reactors were designed and tested based on empirical design criteria and residence time distribution experiments. This work shows that these do not always capture important local effects that are vital for kinetic studies. First the degree of macro–mixing was evaluated for three different geometries (down case, 45° case and 90° case) by performing in silico residence time distribution experiments at 900 K, showing that with these type of experiments only minor differences are observed. However, the ethane steam cracking simulations revealed major differences, with the 45° case being the most uniform in terms of temperature and the 90° case being by far the worst. The species nonuniformity in all geometries was acceptable and was in some cases even partly masked by important shortcut streams such as those observed in the 90° case. The existing gradients on the substrate surface are sufficiently small to be neglected in modeling efforts. As temperature is the major parameter determining the rate of the surface reactions, the 45° case is suggested as the best geometry for measuring intrinsic kinetics.     

Accurate mass determination,quantification and determination of detection limits in liquid chromatography–high-resolution time-of-flight mass spectrometry: Challenges and practical solutions

Uniform guidelines for the data processing and validation of qualitative and quantitative multi-residue analysis using full-spectrum high-resolution mass spectrometry are scarce.     

On the use of AES data analysis to determine local enrichments of conversion coating elements at intermetallic particles on rolled Al

In this paper, the behaviour of the industrial applied Ti/Zr conversion coating (CC) pretreatment on rolled automotive aluminium samples (AA5182) is analysed. Due to its nanometre lateral and depth resolution, Auger electron spectroscopy (AES) is used to analyse the CC distribution at surface cathodic intermetallic particles. As a result of its high surface sensitivity, the AES technique is very susceptible to differences in the top contamination layer thickness. It is demonstrated that AES point measurements performed on aluminium model samples coated with 1.5 and 3 nm of Ti (oxide) layer cannot differentiate the two-layer thicknesses if a difference in the top contamination thickness is not taken into account. A data analysis methodology is introduced, based on the ratio of normalized peak areas (enrichment ratios), to eliminate the effect of the contamination layer thickness. The experimental validation of the methodology is performed on the model samples, demonstrating errors of 2% on the enrichment ratios on similar samples with different contamination layer thicknesses, while the conventional spectra quantification results in errors of 49%. The methodology is also theoretically substantiated within certain constraints. By the use of the AES methodology, an enriched Ti and Zr deposition is confirmed at the cathodic intermetallic particles at the surface of the industrial no-rinse CC sprayed automotive aluminium sheet samples.     

Synthesis,Crystal Structure,and Selected Properties of [Au(S2CNH2)2]SCN: A Precursor for Gold Macro-Needles Consisting of Gold Nanoparticles Glued by Graphitic Carbon Nitride

A new preparation route is developed for the synthesis of needle-like crystals of [Au(S₂CNH₂)₂]SCN, which avoids disproportionation of the Au^I salt used as a starting material. In the crystal structure, the two crystallographically independent Au^III centers are in a square-planar environment of two S₂CNH₂ ligands. The Hirshfeld surface analysis reveals the presence of noncovalent intermolecular S⋅⋅⋅S interactions, which are essential for the spatial arrangement of the molecules. Density functional theory (DFT) calculations including dispersion and damping corrections result in a unit cell volume very close to the value determined experimentally. Thermal decomposition in an inert atmosphere generates black needles with lengths of up to 500 μm. X-ray powder diffraction and pair distribution function analyses demonstrate that the needles are composed of nanosized crystals with a volume-weighted average domain size of 20(1) nm. According to results of X-ray photoemission experiments, the black needles are covered by a nitrogen-rich carbon nitride with composition near (CN)₂N. ¹³C solid-state NMR investigations indicate that two different carbon species are present, with signals corresponding well to heptazine units as in melon and triazine units as in poly(triazin imide) type compounds. Scanning transmission electron microscopy tomography evidences that the needles are composed of slightly elongated nanoparticles.     

Graph Duality in Surface Dynamics

Journal of Nonlinear Science - We compare one-dimensional representations for the isotopy stable dynamics of homeomorphisms in two dimensions. We consider the skeleton graph representative, which...