Skyrmion transport driven by pure voltage generated strain gradient

The magnetic skyrmion transport driven by pure voltage-induced strain gradient is proposed and studied via micromagnetic simulation. Through combining the skyrmion with multiferroic heterojunction, a voltage-induced uniaxial strain gradient is adjusted to move skyrmions. In the system, a pair of short-circuited trapezoidal top electrodes can generate the symmetric strain. Due to the symmetry of strain, the magnetic skyrmion can be driven with a linear motion in the middle of the nanostrip without deviation. We calculate the strain distribution generated by the trapezoidal top electrodes pair, and further investigate the influence of the strain intensity as well as the strain gradient on the skyrmion velocity. Our findings provide a stable and low-energy regulation method for skyrmion transport.     

Strain effects on multiferroic BiFeO3 films

The field of multiferroics has experienced a rapid progress resulting in the discovery of many new physical phenomena. BiFeO₃ (BFO) compound, which is one of the few room-temperature single-phase multiferroics, has contributed subsequently to this progress. As a result, significant review articles have been devoted specifically to this famous system. This chapter is dedicated to the strain effects on the structure stability and property changes of BFO thin films. It is a short and non-exhaustive topical overview that may be seen as an invitation for interested readers to go beyond. There is a very active and prolific research in this field and we apologize to the authors whose relevant work is not cited here. After a short introduction, we will thus review the effect of strain on BFO films by describing the consequences on the structure and the phase transitions as well as on polar, magnetic and magnetoelectric properties.     

Norbornene derivatives from a metal‐free,strain‐promoted cycloaddition reaction: New building blocks for ring‐opening metathesis polymerization reactions

The preparation of new ring opening metathesis polymerization (ROMP) monomers using a 1,3‐dipolar cycloaddition between aryl azides and norbornadiene is described. Various norbornenetriazolines, obtained through a solvent‐and catalyst‐free reaction, can subsequently be incorporated into polymer backbones through ROMP reactions. Furthermore, thermal decomposition of the triazoline moiety can allow for further polymer functionalization. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2357–2362     

用等厚干涉测定液体折射率

介绍一种采用等厚干涉原理测定液体折射率的简单可靠的方法。     

Comparison of growth stress measurements with modelling in thin iron oxide films

High temperature oxidation of metals leads to residual stresses both in the metal and in the growing oxide. In this work, the evolution of this residual stresses is theoretically predicted in the growing oxide layers. The origin of these stresses is based on a microstructural model. Using experimental results providing from the oxidation kinetics, and an analysis proposed to describe the growth strain occurring in the thin layers, a set of equations is established allowing determining the stresses evolution with oxidation time. Then, the model is compared with experimental results obtained on both α-Fe and phosphated α-Fe, oxidised at different temperatures. Numerical data are extracted from experiments either with an asymptotic formulation or with an inverse method. These two methods give good agreement with experiments and allow extracting the model parameters.     

宽带膜厚实时监控过程中膜层折射率的确定方法

为了准确计算出镀膜过程中每层膜的折射率，介绍了实时监控过程中确定膜层折射率的2种方法：一种是由实测的透射比光谱直接反算出膜层的折射率；另一种是用最小二乘法的优化算法实时拟合折射率。试验结果表明：在线反算适合单点监控，所得折射率误差小于2%。然而在实际镀膜过程中,由于宽带内膜层参数误差较大,一般大于25%。为此，采用最小二乘法拟合，即在整个宽光谱范围内采集每个波长点的信息，所得结果误差很小，一般都在2％～5%之间,有时可达到10%,在很大程度上提高了实际镀膜时膜厚监控的精度。     

注浆覆岩离层力学机理及其离层发育分类研究

依据覆岩离层生成的力学机理,结合煤层开采程度的不同,将可注浆层位的离层划分为三类.以岩石的应变为指标,确立了覆岩离层可注浆层位岩梁的断裂步距表达式,理论上证明了划分注浆层位的合理性.根据岩石的全应力应变试验,结合现场实际观测数据,对以应变为指标的岩梁断裂步距表达式做了初步验证.结果表明:可注浆层位的分类和断裂步距表达式的确定对注浆减沉工程具有指导意义.     

Strain hardening of polycarbonate in the glassy state: Influence of temperature and molecular weight

This study is concerned with the temperature and molecular weight dependence of the strain-hardening behavior of polycarbonate. It is shown that the strain-hardening modulus reduces with increasing temperature and decreasing molecular weight. This result is interpreted in terms of temperature accelerated relaxation of the entanglement network. Moreover, it is shown that frozen-in orientations, induced by homogeneous deformations above the glass transition temperature, lead to anisotropic yield behavior that can be fully rationalized (and modelled) in terms of a superimposed stress contribution of the prestrained network. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2041–2049, 2004     

厚度对非极性聚合物薄膜驻极体电荷储存及电荷动态特性的影响

以Du Pont公司的商用Teflon FEP A型薄膜为例，通过热脉冲技术、等温表面电位衰减测量和开路热刺激放电电流谱分析等实验结果，讨论了经常温和高温电晕充电后样品厚度对薄膜驻极体的沉积电荷密度、薄膜驻极体的内电场、体电导率以及电荷储存稳定性的影响.通过热脉冲技术组合电导率温度曲线的测量，研究了在不同温度条件下样品厚度对沉积电荷层的平均电荷重心移动的影响.结果表明：在充电参数一定的条件下，随着膜厚的降低，储存电荷密度上升，但电荷稳定性有所下降.因此，合理地调控薄膜厚度，可以有效地优化驻极体的电荷储存能 关键词： 厚度 驻极体 电荷储存能力 电荷稳定性