高压变质二氧化硅矿物的合成及表征

根据高能机械球磨与地球板块碰撞之间具有的碰撞局域性和剪切应力相似的特点, 采用高能机械球磨和静高温高压技术, 以α-石英与石墨混合粉末为原料, 提出了人工合成地表柯石英的一种新方法. 利用高能机械球磨制备了α-石英和石墨纳米非晶混合粉末, 其高温高压合成柯石英的最低条件是970 K和3.7 GPa. 合成的柯石英有10个Raman峰, 分别位于120, 152, 179, 206, 270, 329, 357, 428, 467和521 cm-1, 是目前最全的柯石英Raman谱.     

Synthesis of ZrSiO4 and Coesite in SiO2-ZrO2 System Under High Pressure

ZrSiO4 and coesite were obtained under high-pressure and high-temperature from the nano precursor of a-SiO2 and ZrO2. XRD and Raman measurements indicate that ZrSiO4 was formed at a temperature higher than 920 ℃ under a pressure of 3.6 GPa. As the pressure increased to 3.9 GPa, the ZrSiO4 formation temperature was reduced to 815 ℃. The formation temperature for coesite was 990 ℃ under 3.9 GPa. The lower formation temperature for ZrSiO4, as compared to that for coesite, provided an experimental evidence that the coesite in the Earth＇s surface usually occurs as inclusions in ZrSiO4.     

Raman mapping of coesite inclusions in garnet from the Kokchetav Massif (Northern Kazakhstan)

Coesite inclusions occur in a wide range of lithologies and coesite is therefore a powerful ultrahigh-pressure (UHP) indicator. The transformation of coesite to quartz is evidenced by three optically well identifiable characteristics (e.g. palisade textures, radial crack patterns, polycrystalline quartz pseudomorphs). Under overpressure monomineralic coesite (on an optical basis), lacking the above transformation characteristics may survive. Raman micro-spectroscopy was applied on monomineralic coesite inclusions in garnet porphyroblasts from diamond-bearing garnet-clinozoisite-biotite gneisses of the Barchi-Kol area (Kokchetav Massif, Northern Kazakhstan). These coesite inclusions are euhedral and display a characteristic anisotropic hallo. However, Raman maps and separate spectra of these inclusions display shifted bands for coesite and quartz. Microscopically undetectable, quartz shows on the Raman map as a thin shell around coesite inclusion. Shift of the main coesite band allows to estimate their overpressure: coesite inclusions record 0-2.4 GPa in garnet and zircon. The quartz shell remains under lower pressure 0-1.6 GPa. The possible application of coesite and quartz Raman geobarometers for UHP metamorphic rocks is discussed.     

Hydrogen capacity of palladium-loaded carbon materials

Several samples of palladium-loaded single-wall carbon nanotubes and palladium-loaded MAXSORB activated carbon were prepared by means of the reaction of the raw carbon support with Pd2(dba)3.CHCl3. When carbon nanotubes were used as the support, the palladium content in the samples reached 13-31 wt % and fine particles of 5-7 nm average size were obtained. In the case of the samples with MAXSORB as the support, the palladium content was higher (30-50 wt %) and the particle size larger (32-42 nm) than in the nanotube samples. At 1 atm and room temperature, the hydrogen capacity of the palladium-loaded samples exceeds 0.1 wt % and is much higher than the capacity of the raw carbon supports (less than 0.01 wt %). The maximum hydrogen capacity at 1 atm and room temperature was found to be 0.5 wt %. A maximum hydrogen capacity of 0.7 wt % was obtained at 90 bar in a palladium-loaded MAXSORB sample, while the capacities for the raw carbon nanotubes and MAXSORB at the same pressure were 0.21 and 0.42 wt %, respectively. At low pressure, it was observed that the H/Pd atomic ratios in the palladium-loaded samples were always higher than in the bulk Pd. The spillover effect is considered as a possible cause of the high H/Pd atomic ratios. On the other hand, the effect of the pressure increase on the spillover was observed to be very low at high pressure and room temperature.     

A High‐Pressure Polymorph of Phosphorus Oxonitride with the Coesite Structure

The chemical and physical properties of phosphorus oxonitride (PON) closely resemble those of silica, to which it is isosteric. A new high‐pressure phase of PON is reported herein. This polymorph, synthesized by using the multianvil technique, crystallizes in the coesite structure. This represents the first occurrence of this very dense network structure outside of SiO₂. Phase‐pure coesite PON (coe‐PON) can be synthesized in bulk at pressures above 15 GPa. This compound was thoroughly characterized by means of powder X‐ray diffraction, DFT calculations, and FTIR and MAS NMR spectroscopy, as well as temperature‐dependent diffraction. These results represent a major step towards the exploration of the phase diagram of PON at very high pressures and the possibly synthesis of a stishovite‐type PON containing hexacoordinate phosphorus.     

Effect of operating conditions and potassium content on Fischer-Tropsch liquid products produced by potassium-promoted iron catalysts

The dependencies of Fischer-Tropsch synthesis liquid hydrocarbon product distribution on operating pressure and temperature have been studied over three potassium-promoted iron catalysts with increasing potassium molar content. The study followed an experimental planning and the results were analyzed based on surface response methodology. The effects of different operating conditions and potassium contents on the liquid product distribution were compared based on number average carbon number and dispersion. Results showed that high pressures （25 to 30 arm） favored the production of waxes that could be converted into liquid fuels through hydrocracking, while greater direct selectivity towards diesel was favored by low pressure （20 arm） using catalysts with low potassium to iron molar ratios. The liquid product distribution produced using an iron catalyst with high potassium content presented higher number-average number of carbons when compared to the distribution obtained using an iron catalyst with low potassium content.     

高压微波制备Pt／C催化剂的工艺研究

利用高压微波消解仪密闭带压、升温速率可控的特点,选择XC-72碳黑为载体,乙二醇为碳黑分散溶剂和还原剂,研究反应温度、升温速率、水含量、Pt含量及表面活性剂等工艺条件对Pt粒子尺寸及其分散度的影响．研究结果表明,快速升温到190℃、控制反应体系中水含量和Pt含量等工艺条件,可以得到Pt粒子平均粒径小于3．1nm的Pt／C催化剂,且Pt粒子分布均匀,无团聚．     

An attempt to correlate fat and protein content of biological samples with residual carbon after microwave-assisted digestion

The residual carbon content of a variety of bovine-derived samples and forage was determined by inductively coupled plasma optical emission spectrometry with radial view configuration (ICP-OES) after microwave-assisted digestion under high pressure in a closed vessel. The original carbon concentration in the samples was determined by elemental analysis. The highest amount of original carbon content (64%) was found in viscera. After digestion, up to 75% of it was destroyed. Viscera presented the highest ether extract and blood exhibited a high crude protein content of up to 99%. The efficiency in destroying the organic matter in biological materials seemed to be related to their fat content and showed no significant difficulty for protein-rich samples. The correlation coefficient between the fat content of the samples and the residual carbon after acid decomposition was 0.9173 indicating a fair fit. However, no correlation was observed between % RC and the protein content.     

Aromatic Compounds Production from Sorbitol by Aqueous Catalytic Reforming

The rules on regulating aromatic compounds production was investigated by aqueous cat-alytic reforming of sorbitol. It was found that aromatics, ketones, furans, organic acids were main compounds in organic phase. The obvious e ect of metal content showed that the highest carbon selectivity of aromatics was 34.36% when 3wt% Ni content was loaded on HZSM-5 zeolite modi ed by MCM-41. However, it was decreased only to 4.82% when Ni content was improved to 20wt%. Meanwhile, di erent reaction parameters also displayed important impacts on carbon selectivity. It was improved with the increase of temperature, while it was decreased as liquid hourly space velocity and hydrogen pressure was increased. The results showed that appropriate higher temperature, longer contact time and lower hy-drogen pressure were in favor of aromatics information, which suggested a feasible process to solve energy crisis.     

Upgrading of woody biomass by torrefaction under pressure

In this study, the upgrading by torrefaction of leucaena, woody biomass, at 200–250 °C under volumetric pressure up to 4 MPa was examined. It was found that the yield of torrefied leucaena decreased with the increase in torrefaction temperature, whereas at the same temperature the yield of torrefied leucaena increased with the increase in torrefaction pressure. From the elemental analyses, the higher carbon content in torrefied leucaena can be achieved by the rising of torrefaction pressure. As large as 92.6% of carbon was recovered in the torrefied leucaena prepared at 250 °C and 4 MPa. On the other hand, the oxygen content decreased to 31.1% for the leucaena torrefied at 250 °C and 4 MPa. The higher heating value (HHV) of leucaena torrefied at high pressure increased significantly when compared to that of leucaena torrefied at atmospheric pressure. As large as 94.3% of energy yield was achieved with the mass yield of 74.4% for the torrefaction at 250 °C and 4 MPa. From the subsequent pyrolysis and combustion in TGA, leucaena torrefied under pressure showed the difference of weight decreasing curves comparing to that of leucaena torrefied at atmospheric pressure. It was found that the weight of leucaena torrefied at high pressure started to decrease at temperature lower than 200 °C. The char yield at 800 °C for the leucaena torrefied at high pressure increased with the increase in torrefaction pressure. These results suggested that the structure of leucaena was changed by the torrefaction under pressure and the cross-linking reactions during the pyrolysis were enhanced by the pressure during the torrefaction resulting in increase in char yields. The substantial increase in char combustion rate was also found for leucaena torrefied under pressure.     

Influence of the characteristics of soil and fly ash on the supercritical carbon dioxide extraction of dioxins.

Several investigations on the extraction of dioxins from soil and fly ash with supercritical fluid have been reported; however, few of them describe the influence of components on the extraction. We extracted dioxins from eight samples with different values of organic carbon content and surface area with supercritical CO(2) at a temperature of 463 K, a pressure of 40 MPa, and using 10% toluene as an entrainer. We researched the influence of the characteristics of soil and fly ash on supercritical CO(2) extraction of dioxins. The results revealed that the extraction efficiencies of PCDD/DFs and PCBs were high for all soil samples, while that of fly ash samples decreased with the increase in organic carbon content and surface area. The extraction efficiencies of dioxins from four standard samples, activated carbon, humic acid, alumina, and florisil, were also examined. The results revealed that the extraction efficiencies were strongly influenced by activated carbon like components present in the samples.     

Examination of sorption and desorption of hydrogen on several samples of polish hard coals

Performed tests showed that at 298?K hard coals sorb relatively small amounts of hydrogen. Those amounts depend on carbon and oxygen content in tested coals. The most considerable amounts of hydrogen are sorbed by coals characterized by strong surface hydrophobicity and high content of aliphatic hydrocarbons. The hydrophilic nature of coal surface does not lead to higher sorption of hydrogen. It was found that the change in amount of sorbed hydrogen is closely related to the moisture. For high moisture coal a significant decrease in hydrogen sorption is observed. Also tests on hydrogen desorption on hard coals were carried out using method of lowering hydrogen pressure above the sorbent. Obtained results showed that tested coals desorb various amounts of hydrogen. Process of sorption is reversible only for some coals, while for the others the desorption isotherm partially lies beneath the sorption isotherm, which indicates that in addition to hydrogen some other chemical substances are emitted from coal.     

Gas permeation properties of asymmetric carbon hollow fiber membranes prepared from asymmetric polyimide hollow fiber

Asymmetric carbon hollow fiber membranes were prepared by pyrolysis of an asymmetric polyimide hollow fiber membrane, and their mechanical and permeation properties were investigated. The carbon membrane had higher elastic modulus and lower breaking elongation than the polyimide membrane. Permeation experiments were performed for single gases such as H₂, CO₂, and CH₄, and for mixed gases such as H₂/CH₄ at high feed pressure ranging from 1 to 5 MPa with or without toluene vapor. The permeation properties of the carbon membranes and the polyimide membrane were compared. There was little change in the properties of the carbon membranes with a passage of time. The properties were hardly affected by the feed pressure, whether the feed was accompanied with the toluene vapor or not, because the carbon membranes were not affected by compaction and plasticization.     

青少年高血压与头发中微量元素关系的分析

为研究青少年高血压与头发微量元素的关系，对50例血压偏高及50例血压正常的青少年头发进行了5种元素的测定。结果表明，高血压组的青少年Zn和Ca含量高于正常组，Fe和Cu则低于正常组，而Mg则无显著差异。     

Influence of activated carbon in zeolite X/activated carbon composites on CH<Subscript>4</Subscript>/N<Subscript>2</Subscript> adsorption separation ability

A series of zeolite X/activated carbon composites with different ratio of zeolite X and activated carbon were prepared, which were adjusted by adding solid pitch powder and silicon dioxide as additional carbonaceous and silica source, respectively. The corresponding modified samples were obtained by treatment with the ammonium chloride solution. CH₄ and N₂ adsorption isotherms on all composites were determined within the pressure of 0–100 kPa at 298 K, and fitted with Henry model and Freundlich model. The results showed the adsorption separation abilities for CH₄ and N₂ were strongly influenced by activated carbon content, micropore structure and surface properties. The increase of activated carbon content increased the BET surface area, micropore surface area and micropore volume, leading to an enhanced CH₄ adsorption capacity and CH₄/N₂ adsorption selectivity. Compared with the unmodified composites, the modified composites showed higher CH₄/N₂ adsorption selectivity, and CH₄ adsorption capacity decreased slightly, which can be attributed to the reduction of the micropore structure parameters, the surface basic amount and basic strength. Furthermore, the modified composite HAX-3 presented the highest CH₄/N₂ selectivity of 3.4, and high CH₄ adsorption capacities, which is favorable for application in pressure swing adsorption processes.     

Surface modification of carbonyl iron powders with silicone polymers in supercritical fluid to get higher dispersibility and higher thermal stability

The surface of carbonyl iron powder (CIP) was modified in supercritical fluid with silicone polymers containing reactive Si‐OCH₃ groups. Fourier‐transformed infrared spectroscopy, X‐ray photoelectron spectroscopy, X‐ray diffraction, and thermo gravimetric analysis were adopted to characterize CIP. The dispersibility of CIP in epoxy resin matrix was evaluated by castor oil absorption factor, dynamic viscosity, Mooney viscosity, and scanning electric micrograph. The electromagnetic reflectivity of the CIP‐filled epoxy resin coatings was also checked. It was confirmed that comparing with those treated at atmosphere, the supercritical treated CIP presented higher surface carbon content, higher dispersibility, higher thermal stability, and its original crystalline structure did not change greatly. Even though it experienced a high temperature and a high pressure (250 °C, 7.8 Mpa) during supercritical treatment, it was not oxidized, and its electromagnetic reflectivity did not decrease. Copyright © 2016 John Wiley & Sons, Ltd.     

A facile soft-template synthesis of nitrogen doped mesoporous carbons for hydrogen sulfide removal

A series of nitrogen-doped mesoporous carbons (NMCs) were prepared using Pluronic F127 as a structure directing agent, phloroglucinol and formaldehyde as carbon precursor and dicyandiamide as nitrogen source. The obtained nitrogen-doped mesoporous carbons possess high nitrogen content of 6.37–19.28 wt%. Due to the feature of high nitrogen contents, NMCs show superior H₂S adsorption performance with breakthrough sulfur capacity of 0.48 mmol g^?1 at room temperature and ambient pressure. It is revealed that in addition to the nitrogen content, nitrogen configuration and porosity of the carbon materials also influence significantly their sulfur capacity. This work offers a facile strategy for the synthesis of porous carbon materials with excellent performance in the adsorptive removal of H₂S.     

Absorption and foaming of plastics using carbon dioxide

In this study, carbon dioxide was used as a foaming agent for common plastics, such as acrylonitrile–butadiene–styrene (ABS) polymer, polystyrene (PS), polypropylene (PP), high-density polyethylene (HDPE), and high impact polystyrene (HIPS). Carbon dioxide was first absorbed by the sample plastics placed within a pressure vessel at various pressure levels and absorption time intervals. The Henry’s constant of the absorbed carbon dioxide in the plastics was determined. The diffusion coefficient of carbon dioxide in polymer was also identified by curve-fitting with the relationship between the absorbed amount and time. The results showed that ABS, PS, and HIPS absorbed more gas than did PP and HDPE, because PP and HDPE exhibit higher crystallinity. Generally, a polymer can take up saturation absorption of gas under higher pressure. After absorption, the foaming process occurred at various temperatures and time intervals. The cell structure, density, and size of the plastic foams were then investigated using scanning electron microscopy. A longer foaming period and higher temperature increase the size of the cell and decrease the cell density (the number of bubbles per unit volume). A dense skin layer without bubbles appeared directly adjacent to the surface of the foamed plastics. Its thickness decreased if the foaming process took place at higher temperatures.     

KOH对超临界水中褐煤连续制氢的影响

采用连续式超临界水反应装置,以20%的水煤浆为反应原料,考察了不同KOH/煤质量比、温度、压力对褐煤制氢过程的影响。实验结果表明,在水煤浆中添加KOH可以提高碳气化率及H2的体积分数和产率,在600℃、25 MPa、KOH/煤质量比为4.1%时,与未加KOH相比,气相产物收率由29.6%提高到49.5%,碳气化率由23.0%增大到31.5%;H2的产率由135.4 mL/(g daf coal)提高到239.1 mL/(g daf coal)。随着温度的升高,H2产率逐渐增大,650℃时达到287.8 mL/(g daf coal),是500℃时的5.4倍;高温、高压下,KOH对煤气化过程的催化作用更为明显。     

煤质对H2/Ar等离子体热解制乙炔的影响

选取12种不同变质程度的煤，通过等离子体热解实验考察了煤的挥发分产率、煤中氧质量分数、灰分产率对乙炔收率和结焦的影响。研究结果表明，挥发分产率为30%～40%的烟煤，热解时具有较高的乙炔收率；含氧量越高的煤，生成的碳氧化物越多，相应的乙炔收率较低；煤中的矿物质与乙炔收率之间并不存在相关性，但煤中的矿物质有利于CO的生成。影响结焦量的主要因素与煤的矿物质密切相关，煤中掺入二氧化硅和天然河沙能够明显增加结焦量，改变结焦形态。