稀土固体超强酸SO_4~(2-)/TiO_2-Ce~(4+)直接法催化合成聚乳酸

滴定沉淀法制备了SO42-/TiO2-Ce4+稀土固体超强酸催化剂,得到了可作为直接法合成聚乳酸催化剂的制备工艺:硫酸浸渍浓度1.0 mol/L,Ce4+浓度0.08 mol/L,浸渍时间10 h,焙烧温度500℃,焙烧时间3 h,并将该固体超强酸催化剂用于直接催化合成聚乳酸。考察了聚合温度、聚合时间、催化剂用量及聚合压力对聚乳酸合成的影响,得到了最佳工艺条件为:催化剂用量为乳酸质量的0.174%,先在120℃,2 000 Pa下预聚5 h,然后在180℃,1 000 Pa下聚合15 h,最后在120℃,500 Pa下聚合20 h,得到的聚乳酸分子量为1.39×104。     

共沸除氯工艺制备稀土固体超强酸SO42-/SnO2-Nd2O3及其表征

采用共沸除氯工艺制备固体超强酸SO42-/SnO2-Nd2O3,可免除抽滤,大大节省催化剂的制备时间。将其应用于α-蒎烯的异构化反应,考察了催化剂的最佳制备条件,并利用FT-IR、XRD、TG-DTA、BET等技术对催化剂进行了表征。结果表明,稀土Nd2O3的引入,延缓了SnO2晶化,提高了SO42-/SnO2的催化活性;催化剂最佳制备条件为:Nd2O3引入量为SnO2的3 mol%,浸渍液浓度1.0 mol/L,焙烧温度500℃,焙烧时间2 h。     

固体超强酸SO_4~(2-)/SnO_2-Al_2O_3的红外光谱研究

以四氯化锡、硫酸铝为原料,氨水为沉淀剂,采用共沉淀法制得新型固体超强酸SO42-/SnO2-A l2O3。采用FT-IR技术考察了金属元素摩尔比、焙烧温度、浸渍液以及掺杂稀土氧化物对该固体超强酸结构和性能的影响。FT-IR结果表明在该固体超强酸中,锡和硫酸根是以螯合和桥式两种方式配位结合,其中起催化活化作用的主要是和硫酸根以螯合双齿结合的锡;和SO42-/ZrO2型超强酸相比,SO42-/SnO2-A l2O3超强酸的硫酸根FT-IR特征吸收峰发生蓝移,显示出更强的酸性。锡铝摩尔比为9∶1、焙烧温度为773K、焙烧时间为3h时,制得的SO42-/SnO2-A l2O3样品对酯化反应的催化性能最好。     

稀土固体超强酸so2-4/tio2-ce4+直接法催化合成聚乳酸

滴定沉淀法制备了SO2-4/TiO2-Ce4+稀土固体超强酸催化剂,得到了可作为直接法合成聚乳酸催化剂的制备工艺:硫酸浸渍浓度1.0 mol/L,Ce4+浓度0.08 mol/L,浸渍时间10 h,焙烧温度500 ℃,焙烧时间3 h,并将该固体超强酸催化剂用于直接催化合成聚乳酸.考察了聚合温度、聚合时间、催化剂用量及聚合压力对聚乳酸合成的影响,得到了最佳工艺条件为:催化剂用量为乳酸质量的0.174%,先在120 ℃,2 000 Pa下预聚5 h,然后在180 ℃,1 000 Pa下聚合15 h,最后在120 ℃,500 Pa下聚合20 h,得到的聚乳酸分子量为1.39×104.     

固体超强酸SO2-4/SnO2-Al2O3的红外光谱研究

以四氯化锡、硫酸铝为原料,氨水为沉淀剂,采用共沉淀法制得新型固体超强酸SO2-4/SnO2-Al2O3.采用FT-IR技术考察了金属元素摩尔比、焙烧温度、浸渍液以及掺杂稀土氧化物对该固体超强酸结构和性能的影响.FT-IR结果表明在该固体超强酸中,锡和硫酸根是以螯合和桥式两种方式配位结合,其中起催化活化作用的主要是和硫酸根以螯合双齿结合的锡;和SO2-4/ZrO2型超强酸相比,SO2-4/SnO2-Al2O3超强酸的硫酸根FT-IR特征吸收峰发生蓝移,显示出更强的酸性.锡铝摩尔比为9∶1、焙烧温度为773K、焙烧时间为3h时,制得的SO2-4/SnO2-Al2O3样品对酯化反应的催化性能最好.     

Sno2+Sb203中间层的制备条件对Ti/SnO2+Sb2O3/PbO2阳极性能的影响

研究了聚合前驱体制备的SnO2+Sb2O3中间层的焙烧温度、锑含量对Ti/SnO2+Sb2O3/PbO2阳极性能的影响. 用XRD、ESEM和探针法对锡锑中进行了表征,应用阳极寿命快速检测法测定了Ti/SnO2+Sb2O3/PbO2电极在1.0 mol/L H2SO4溶液中的寿命,并用极化曲线和电荷容量表征了锡锑中间层对钛基PbO2阳极性能的影响. 实验结果表明,聚合前驱体制备中间层的焙烧温度和锑含量对Ti/SnO2+Sb2O3/PbO2电极的寿命和性能有显著的影响. 在锡锑中间层的制备温度为500 ℃、n(Sn):n(Sb)=9:1时,制得的Ti/SnO2+Sb2O3/PbO2电极用阳极寿命快速检测法测得的电极寿命达30h,具有良好的稳定性.     

稀土固体超强酸SO_4~(2-)/TiO_2/La~(3+)催化合成丙酸苄酯

采用浸渍法制备了稀土固体超强酸SO2 -4/TiO2 /La3 + ,并运用IR、XRD和Hammett指示剂法对其进行了表征。以制备的固体超强酸SO2 -4/TiO2 3 + 为催化剂、丙酸和苯甲醇为原料合成了丙酸苄酯。考察了催化剂的制备条件及合成条件对酯化率的影响 ,结果显示催化剂最佳制备条件 :钛前体氧化物的浸渍液为含 0 0 7mol·L-1La3 + 的硫酸溶液 ,焙烧时间 3h ,焙烧温度 5 0 0℃。最佳反应条件 :醇酸摩尔比为 1∶2、催化剂用量为苯甲醇用量的 9 3%、反应时间 3h、反应温度 12 0℃ ,酯化率达 84 0 %以上。用IR、1H NMR等手段对产品进行了表征。     

SO_4~(2-)/Ce-TiO_2光催化降解二甲基二氯乙烯基磷酸酯

以钛酸四丁酯 (Ti(OBu) 4 )、Ce(NO3 ) 3 、H2 SO4为主要原料 ,采用溶胶 凝胶法制备了SO2 -4/Ce TiO2 光催化剂 ,用XRD、IR、BET、XPS、TG DTA等测定技术对所制得的试样进行了表征 ,并将其用于光催化降解二甲基二氯乙烯基磷酸酯的稀释液。结果表明 ,SO2 -4/Ce TiO2 中TiO2 以锐钛矿晶型存在 ,并且具有超强酸特征 ,当n(Ce) /n(TiO2 ) =0 0 0 5 ,c(H2 SO4) =0 5mol/L时 ,焙烧温度为 5 0 0℃是最佳制备条件 ,其光催化降解性能较Ce TiO2 有明显提高。     

SnO_2 Sb_2O_3中间层的制备条件对Ti/SnO_2 Sb_2O_3/PbO_2阳极性能的影响

研究了聚合前驱体制备的SnO2 Sb2 O3 中间层的焙烧温度、锑含量对Ti/SnO2 Sb2 O3 /PbO2 阳极性能的影响。用XRD、ESEM和探针法对锡锑中间层进行了表征 ,应用阳极寿命快速检测法测定了Ti/SnO2 Sb2 O3 /PbO2 电极在 1 0mol/LH2 SO4溶液中的寿命 ,并用极化曲线和电荷容量表征了锡锑中间层对钛基PbO2 阳极性能的影响。实验结果表明 ,聚合前驱体制备中间层的焙烧温度和锑含量对Ti/SnO2 Sb2 O3 /PbO2 电极的寿命和性能有显著的影响。在锡锑中间层的制备温度为 5 0 0℃、n(Sn)∶n(Sb) =9∶1时 ,制得的Ti/SnO2 Sb2 O3 /PbO2 电极用阳极寿命快速检测法测得的电极寿命达 30h ,具有良好的稳定性     

SO_4~(2-)/SnO_2催化剂的制备及其对苯硝化反应的催化活性

采用(NH4)2SO4溶液浸渍法制备了一系列SO42-/SnO2催化剂(Cat-n,n=5,10,15,20),其结构经IR表征。以Cat-10(焙烧温度500℃)催化苯液相硝化反应的研究结果表明,引入SO24-后催化剂的活性显著增加,硝基苯产率63.8%。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.