微波消解样品-电感耦合等离子体质谱法测定植物灰分中微量元素

应用电感耦合等离子体质谱法(ICP-MS)同时测定植物灰分中21种微量元素和15种稀土元素.用微波消解样品,对微波消解植物灰分样品的条件进行了试验.其优选微波消解条件为:微波压力为2 MPa,消解时间为10 min,以硝酸、盐酸、氢氟酸、高氯酸(体积比为6比2比1比1)的混合酸消解样品,对0.100 0 g植物标准物质(GBW 07603)进行10次平行测定,微量元素测定结果的相对标准偏差(n=10)在0.87%～5.96%之间,稀土元素测定结果的相对标准偏差(n=10)在2.14%～8.00%之间.     

高压密闭消解-电感耦合等离子体质谱法测定煤中稀土元素

煤作为有机物与无机物的复杂混合物,含有多种微量元素,不同的微量元素信息代表不同的地质意义,稀土元素可以提供丰富的沉积环境与物源信息。采用高压消解罐,选用硝酸和氢氟酸混合酸消解样品,建立了电感耦合等离子体质谱法测定16种稀土元素的方法。讨论了样品量、消解试剂、质谱干扰等影响因素,各元素的方法检出限在0.001～0.016μg/g,NIST SRD 1632d煤标准样品实测值和标准值一致,标准样品测定结果与实测样品结果相对标准偏差(RSD,n=11)小于5%,可满足煤中稀土元素的准确测定,为煤类样品中稀土元素测定提供了新的参考方法。     

高压密闭消解-电感耦合等离子体质谱(ICP-MS)法测定煤中稀土元素

煤作为有机物与无机物的复杂混合物,含有多种微量元素,不同的微量元素信息代表不同的地质意义,稀土元素可以提供丰富的沉积环境与物源信息。采用高压消解罐,选用硝酸和氢氟酸混合酸消解样品,建立了电感耦合等离子体质谱法测定16种稀土元素的方法。讨论了样品量、消解试剂、质谱干扰等影响因素,各元素的方法检出限在0.001～0.016μg/g,NIST SRD 1632d煤标准样品实测值和标准值一致,标准样品测定结果与实测样品结果相对标准偏差(RSD,n=11)小于5%,可满足煤中稀土元素的准确测定,为煤类样品中稀土元素测定提供了新的参考方法。     

微波消解-石墨炉原子吸收光谱法测定植物染发剂中的铅镉铜

建立了微波消解-石墨炉原子吸收光谱法测定植物染发剂中重金属铅、镉和铜的方法.采用L9(34)正交设计讨论了固液比、消解剂体积比、消解时间和消解压力对样品消解效果的影响,最佳的消解条件:固液比(g/mL)为1∶12,HNO3/H2O2(V/V)为4∶1,消解时间为5min,消解压力1.5MPa.在最佳微波消解条件下,进行了精密度实验、回收率实验,相对标准偏差为1.05%~3.35%,回收率为96.67%~105.43%.微波消解法处理植物染发剂样品,试剂用量少、消解完全、快速、简便,而且测定结果的精密度、准确度较好.     

微波消解-FAAS法测定大别山区三种中药中的微量元素

采用微波消解-火焰原子吸收光谱(FAAS)法对大别山区3种中药(何首乌、黄精和拐枣)中的微量元素进行测定。用微波消解仪处理样品,对消解条件及消解程序进行优化,在最佳微波消解条件下,结合FAAS法测定上述3种中药中Ca、Mg、Cu、Zn、Fe、Mn 6种元素的含量。结果表明,微波消解的最佳条件为:何首乌和拐枣采用HNO3-H2O2混酸体系,配比分别为5∶2和5∶3,固液比1∶20,最高功率(700W)时的保温时间分别为8min和6 min;黄精采用HNO3-HCl,混酸体系,配比5∶2,固液比1∶28,保温时间为8 min。所建立的定量分析方法回收率为95.63%～101.36%,相对标准偏差小于3.0%,线性相关系数大于0.999,方法检出限为0.18～2.20 ng/mL。3种中药中均含有丰富的微量元素,尤其是黄精中Fe、Ca和Mn的含量较高;何首乌中Mg、Zn和Fe含量相对较高;拐枣中Fe和Ca含量相对较高。研究结果可为上述3种中药中微量元素的含量与其药效的相关性提供科学依据。     

微波消解-火焰原子吸收光谱法测定土壤中重金属元素的含量

将微波消解运用于火焰原子吸收光谱法对土壤中Mn,Pb,Cu和Cr微量元素含量的测定.通过正交实验进行了微波消解条件的优化,还进行了消解结果精密度实验,该方法的加标回收率为98.3%～107.3%,相对标准偏差(RSD)小于0.25%,具有较好的准确度和精密度.     

催化剂中钨的测定溶样方法的改进

研究了新的溶样方法——微波消解法，并将其与常规光度法相结合测定催化剂中钨。考察了测定条件，研究了消解用酸的种类、用量和不同的消解程序对消解效果的影响，确定了微波消解催化剂的最佳消解程序。将经微波消解处理的催化剂样品用常规光度法测定钨的含量，其相对误差小于2．0%，相对标准偏差小于1．3%。将微波消解法与常压敞口消解法进行对比，测定结果基本一致。微波消解法酸用量减少了约5．0倍，消解速度提高了3．5～6．7倍。该方法具有省时、省酸、样品损失少、无环境污染、测定结果准确可靠等优点。     

微波消解-连续流动火焰光度法测定烤烟中的钾含量

用HNO3-H2O2体系于微波消解仪中密闭消解烟草样品,以连续流动火焰光度法快速测定烤烟中的钾含量,方法回收率在99.47%～100.08%之间,相对标准偏差小于2%,与标准值的相对误差为1.19%.并与硫酸常压消化方式相比,操作步骤少,速度快,精密度和准确度高.     

微波消解-电感耦合等离子体质谱法测定砂仁中的铜、铅、砷、镉

建立了微波消解样品,电感耦合等离子体质谱法(ICP–MS)测定黔西南高砷土壤种植的砂仁中痕量铜、铅、砷、镉的分析方法。对微波消解条件进行了优化。为了避免消解试剂对质谱测定的干扰,选择硝酸–双氧水混合溶液(体积比为3∶1)作为微波消解试剂,采用ICP–MS测定消解液中铜、铅、砷、镉的含量。利用校正方程对砷、镉的质谱干扰进行校正。铜、铅、砷、镉4种元素的线性相关系数均大于0.999 2,检出限分别为0.073,0.048,0.39,0.062μg/L,测定结果的相对标准偏差小于4.5%(n=5)。各元素的加标回收率在96.0%～105.0%之间。该方法样品处理快速、简单,溶解率高,测定结果准确、可靠,适用于成批量砂仁样品中铜、铅、砷、镉微量元素的测定。     

微波消解-电感耦合等离子体质谱法测定地质样品中稀土元素

建立了微波消解-电感耦合等离子体质谱(ICP-MS)测定地质样品中稀土元素的方法,采用HNO3-HF体系-微波消解进行样品前处理,经赶酸后再用5 m L 1∶1 HNO3提取,整个过程安全、高效、无损失。利用ICP-MS进行测定,可以有效降低多原子离子质谱干扰,在优化仪器参数后,用内标铑(Rh)进行校正,弥补基体抑制效应和灵敏度漂移,测试结果更加准确。方法用于岩石标准物质(GBW07109,GBW07110和GBW07111)测试,其测定值与标准值相一致。结果表明,该方法的检出限低,准确度高,操作简单快捷,可同时测定多种元素,能满足批量测定地质样品中稀土元素含量的要求。     

Furyl- and thienyl-silatranes and germatranes

We review our research on the synthesis and study of the physical and biological properties of furyl- and thienylgermatranes and -silatranes.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 6, pp. 725–732, June, 1992.     

Review and patents and literature

The use of the insect cell/baculovirus expression system for producing recombinant proteins of bacterial, plant, insect, and mammalian origin has become widespread. The popularity of this eukaryotic expression system is due to many factors, including (1) potentially high protein expression levels, (2) ease and speed of genetic engineering, (3) ability to accommodate large DNA inserts, (4) protein processing similar to higher eukaryotic cells (e.g., mammalian cells), and (5) ease of insect cell growth (e.g., suspension growth). The following review of the literature discusses two engineering aspects of recombinant protein synthesis by insect cell cultures: bioreactor scale-up and insect cell line selection. Following this review patent abstracts and additional literature pertaining to expression of recombinant proteins in insect cell culture are listed.     

Ground- and excited-state aromaticity and antiaromaticity in benzene and cyclobutadiene

The aromaticity and antiaromaticity of the ground state (S 0), lowest triplet state (T 1), and first singlet excited state (S 1) of benzene, and the ground states (S 0), lowest triplet states (T 1), and the first and second singlet excited states (S 1 and S 2) of square and rectangular cyclobutadiene are assessed using various magnetic criteria including nucleus-independent chemical shifts (NICS), proton shieldings, and magnetic susceptibilities calculated using complete-active-space self-consistent field (CASSCF) wave functions constructed from gauge-including atomic orbitals (GIAOs). These magnetic criteria strongly suggest that, in contrast to the well-known aromaticity of the S 0 state of benzene, the T 1 and S 1 states of this molecule are antiaromatic. In square cyclobutadiene, which is shown to be considerably more antiaromatic than rectangular cyclobutadiene, the magnetic properties of the T 1 and S 1 states allow these to be classified as aromatic. According to the computed magnetic criteria, the T 1 state of rectangular cyclobutadiene is still aromatic, but the S 1 state is antiaromatic, just as the S 2 state of square cyclobutadiene; the S 2 state of rectangular cyclobutadiene is nonaromatic. The results demonstrate that the well-known "triplet aromaticity" of cyclic conjugated hydrocarbons represents a particular case of a broader concept of excited-state aromaticity and antiaromaticity. It is shown that while electronic excitation may lead to increased nuclear shieldings in certain low-lying electronic states, in general its main effect can be expected to be nuclear deshielding, which can be substantial for heavier nuclei.     

Hard and soft acids and bases: structure and process

Under investigation is the structure and process that gives rise to hard-soft behavior in simple anionic atomic bases. That for simple atomic bases the chemical hardness is expected to be the only extrinsic component of acid-base strength, has been substantiated in the current study. A thermochemically based operational scale of chemical hardness was used to identify the structure within anionic atomic bases that is responsible for chemical hardness. The base's responding electrons have been identified as the structure, and the relaxation that occurs during charge transfer has been identified as the process giving rise to hard-soft behavior. This is in contrast the commonly accepted explanations that attribute hard-soft behavior to varying degrees of electrostatic and covalent contributions to the acid-base interaction. The ability of the atomic ion's responding electrons to cause hard-soft behavior has been assessed by examining the correlation of the estimated relaxation energies of the responding electrons with the operational chemical hardness. It has been demonstrated that the responding electrons are able to give rise to hard-soft behavior in simple anionic bases.     

Determination and study on residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil

A QuEChERS (quick, easy, cheap, effective, rugged, and safe) method for the determination of benazolin-ethyl and quizalofop-p-ethyl in rape and soil by high-performance liquid chromatography-tandem mass spectrometry has been developed in this study. The residue and dissipation of benazolin-ethyl and quizalofop-p-ethyl in rape and soil were determined with the developed method. The half-lives of benazolin-ethyl in rape straw and soil were 3.7–5.1 days and 14.3–26.3 days, respectively. The half-lives of quizalofop-p-ethyl in rape straw and soil were 5.0-6.1 days and 0.3–9.7 days, respectively. The residue of benazolin-ethyl and quizalofop-p-ethyl in rapeseed and soil were below the detection limit (i.e., 0.5?mg?kg^?1, the maximum residue level of European Union for quizalofop-p-ethyl).     

Syntheses and structures of P-anilino-P-chalcogeno- and P-anilino-P-iminodiazasilaphosphetidines and their group 12 and 13 metal compounds

The P-anilino-P-chalcogeno(imino)diazasilaphosphetidines [Me(2)Si(mu-N(t)Bu)(2)P=E(NHPh)] (E = O (3), S (4), Se (5), N-p-tolyl (6)) were synthesized by oxidizing the P-anilinodiazasilaphosphetidine [Me(2)Si(N(t)Bu)(2)P(NHPh)] (2) with cumene hydroperoxide, sulfur, selenium, and p-tolyl azide, respectively. The lithium salt of 4 reacted with thallium monochloride to produce ([Me(2)Si(mu-N(t)Bu)(2)P=S(NPh)-kappaN-kappaS]Tl)(7), which features a two-coordinate thallium atom. Treatment of 4-6 with AlMe(3) gave the monoligand dimethylaluminum complexes ([Me(2)Si(mu-N(t)Bu)(2)P=E(NPh)-kappaN-kappaE]AlMe(2)) (E = S (8), Se (9), N-p-tolyl (10)), respectively. In these complexes the aluminum atom is tetrahedrally coordinated by one chelating ligand and two methyl groups, as a single-crystal X-ray analysis of 8 showed. A 2 equiv amount of 4-6 reacted with diethylzinc to produce the homoleptic diligand complexes ([Me(2)Si(mu-N(t)Bu)(2)P=E(NPh)-kappaN-kappaE](2)Zn)(E = S (11), Se (12), N-p-tolyl (13)). A crystal-structure analysis of 11 revealed a linear tetraspirocycle with a tetrahedrally coordinated, central zinc atom.