Fe3O4@Cu2O纳米粒子的制备及其催化性能研究

利用室温液相还原、晶种生长的方法,成功的制备了大小形貌均一、性能稳定且具有磁性的Fe3O4@Cu2O复合纳米粒子,并且对制备的Fe3O4@Cu2O纳米粒子进行了光催化性能的研究.在以紫外光为光源的照射下,合成的Fe3O4@Cu2O纳米粒子对有机染料甲基蓝溶液起到很好的降解作用.更重要的是,在外加磁场的作用下,Fe3O4@Cu2O纳米粒子容易回收,具有良好的可循环利用性能.     

LaPO4∶Eu3+—Fe3O4光-磁复合材料的合成与性能研究

采用2步水热法合成了LaPO4∶Eu3+-Fe3O4复合材料.在LaPO4∶Eu3+-Fe3O4复合材料中,LaPO4∶Eu3+为单斜晶相,呈纳米棒状,纳米棒的直径和长度分别为20~100nm和0.2~1μm;Fe3O4为正交晶相、呈20~30nm的颗粒状,Fe3O4粒子紧紧附着在LaPO4∶Eu3+纳米棒的表面;样品的磁性和发光性质研究表明所合成的LaPO4∶Eu3+—Fe3O4复合材料既具有发光性质又具有磁性.     

纳米Fe3O4/聚苯乙烯均匀分散体系的制备及结构

用化学共沉淀法制备了Fe3O4纳米颗粒,以油酸为表面活性剂,苯乙烯为载液,制备了稳定的纳米Fe3O4可聚合磁流体,将可聚合磁流体经自由基引发聚合制成纳米Fe3O4/聚苯乙烯均匀分散体系,用WAXRD研究了Fe3O4纳米粒子的结晶情况;用FTIR研究了油酸表面改性前后Fe3O4粒子表面官能团的变化;用TEM研究了Fe3O4颗粒的粒径大小及其在苯乙烯单体和聚苯乙烯中的分散情况;用DSC和TGA研究了纳米Fe3O4/聚苯乙烯均匀分散体系的玻璃化转变温度(Tg)和热稳定性,结果表明,合成的纳米Fe3O4为立方晶型,平均粒径在10nm左右,油酸分子在Fe3O4表面是化学吸附,经表面处理的Fe3O4超细颗粒在苯乙烯和聚苯乙烯基体中分散较均匀.界面粘结较好,含1.8％Fe3O4纳米颗粒的聚苯乙烯的最大热失重温度比聚苯乙烯提高了13K,Fe3O4/聚苯乙烯复合体系的饱和磁化强度σs为17.43emu/g.     

Fe3O4纳米晶的简单调控合成、表征及磁性能

采用醋酸铵作保护剂在200℃下制备了单分散的400 nm粒径的Fe3O4空心纳米球.通过改变实验条件,对产品的形貌、内部结构和粒径进行了调控合成,得到了粒径范围在100～200 nm的实心纳米球和片形结构的Fe3O4纳米材料.采用SEM、TEM和XRD等对样品进行了表征.结果表明,所得尖晶石型Fe3O4纳米晶粒径均匀,分散度好.利用振动样品磁场计检测了不同形貌样品的磁性能.结果显示,Fe3O4纳米空心球的饱和磁化强度和矫顽力均大于Fe3O4纳米片的对应值.     

柠檬酸盐改性Fe3O4水溶液分散性研究

四氧化三铁(Fe3O4)的水溶液分散性是影响其在生物医学中使用效果的关键因素。以FeSO4和乙二醇为原料,通过柠檬酸根离子改性,采用水热法合成了水溶液分散性良好的Fe3O4粒子。采用X-射线衍射(XRD)、扫描电镜(SEM)和红外光谱(FT-IR)分析等测试手段对制备的Fe3O4的物相、形貌、尺寸、表面吸附官能团进行了表征。研究了柠檬酸盐对样品形貌、尺寸、结晶性和水溶液分散性的影响。与未改性的Fe3O4相比,柠檬酸盐改性后的Fe3O4粒子表现出优异的水溶液分散性。     

Fe3O4纳米晶的粒径控制合成、表征及其吸波性能

采用十二烷基磺酸钠和聚乙二醇作为保护剂, 成功地制备出Fe3O4纳米晶. 通过改变实验条件, 可在10~200 nm范围内有效调控Fe3O4纳米晶的粒径. 采用X射线衍射仪、透射电子显微镜和扫描电子显微镜等对样品的微观结构、粒径和形貌进行了分析. 结果表明, 所得尖晶石型Fe3O4纳米晶粒径均匀, 形貌均为球形. 利用振动样品磁场计测量了不同粒径样品的磁性能. 结果显示, 粒径小时, 随着粒径的增加, Fe3O4的饱和磁化强度Ms逐渐增加, 但当粒径增加到80 nm时, Ms达到最大值; 随着粒径的减小, 矫顽力也随之减小. 利用矢量网络分析仪对不同粒径样品的电磁性能和吸波性能进行了研究, 结果表明, 当Fe3O4纳米晶的粒径小于100 nm时, 吸波性能良好, 其中, 粒径为20 nm的样品吸收峰的峰值在8 GHz附近达到了-32 dB.     

Fe3O4@SiO2@YF3∶Eu3+磁-光双功能复合粒子的制备与性能

采用水热法合成了Fe3O4@SiO2@YF3∶Eu3+磁-光双功能复合粒子,对其结构和性能进行了表征。XRD分析表明:Fe3O4表面包覆上了结晶良好的正交晶系的YF3。TEM照片表明:复合粒子为球形,构成核的Fe3O4颗粒的尺寸在200～350 nm之间,Fe3O4@SiO2@YF3∶Eu3+核壳结构复合粒子的尺寸约为230～380 nm,与包覆前的Fe3O4相比较,包覆后,颗粒尺寸增大,并且YF3∶Eu3+是以棒状结构连接在Fe3O4球型颗粒的表面。磁性和荧光光谱分析表明:该复合颗粒同时具有良好的发光性和磁性,使其在生物医学领域具有潜在的应用。     

中空球状Fe3O4颗粒的合成及对刚果红溶液吸附-脱附能力的研究

通过简单的水热过程合成具有优良磁学性能的中空Fe3O4单晶颗粒。空心球状颗粒外部直径约500 nm,内径约200 nm,是由粒径为50 nm的颗粒团聚而成。随着反应时间的增加,相邻的Fe3O4纳米晶沿着(311)晶面取向团聚,经过奥斯瓦尔德熟化过程最终形成中空的球状颗粒。实验合成的Fe3O4粒子表现出特殊的磁学性能,具有相对较低的饱和磁化强度和较高的矫顽力。通过对刚果红溶液的吸附-脱附实验证明,中空结构Fe3O4颗粒对刚果红溶液有更高的吸附和脱附能力,在废水处理过程中,采用Fe3O4作为吸附剂,可以更高效的去除溶解的有机污染物,同时可以回收再利用,提高废水净化率,也进一步扩展了磁性材料的应用领域。     

无溶剂Fe3O4纳米流体的制备及表征

采用共沉淀法合成Fe3O4纳米粒子, 将含有硅氧烷基的离子型改性剂二甲基十八烷基氯化铵与Fe3O4纳米粒子进行接枝反应, 再用脂肪醇聚氧乙烯醚磺酸盐的长链阴离子交换Cl-, 在Fe3O4纳米粒子表面生成具有阴、 阳离子双电层结构的表面处理层, 得到无溶剂Fe3O4纳米流体. 研究结果表明, 在Fe3O4纳米粒子表面成功接枝了有机物长链, 改性的Fe3O4纳米粒子呈单分散分布, 其损耗剪切模量G″明显大于储能剪切模量G', 具有明显的流体行为, 在室温下即可流动.     

纳米四氧化三铁(Fe3O4)的制备和形貌

纳米Fe₃O₄因其特殊的理化性质和在生物医学领域潜在的应用价值而得到广泛研究。本文综述了纳米Fe3O4的制备方法，包括直流电弧等离子体法、热分解方法、沉淀法、水热法、电化学法、微乳液法、溶胶-凝胶法、有机物模板法、回流法等，结合作者在Fe3O4纳米粒子制备方面的最新工作，介绍了Fe3O4纳米粒子的新颖形貌。对纳米级Fe3O4制备研究的发展趋势进行了展望。     

PREPARATION OF Fe3O4/PSt MAGNETIC PARTICLES IN THE PRESENCE OF MAGNETIC FLUID IN ETHANOL/WATER MIXTURE*

Fe_3O_4/Polystyrene(PSt) magnetic particles with core/shell structure have been prepared in thepresence of Fe_3O_4 magnetic fluid in ethanol/water medium by dispersion polymeriation of styrene. A Fe_3O_4particle formation mechanism was proposed. According to this mechanism, the size of particle nuclei isdetermined by the extent of aggregation of Fe_3O_4 /oligomer. Magnetic particles with diameter ranging from 5to 200 μm were prepared under different reaction conditions. Some polymerization parameters such as theconcentration of monomer, stabilizer, initiator, and ethanol which affect particle size and size distribution arediscussed and their effect on particle formation are explained by the proposed mechanism.     

单分散NixZn1-xFe2O4纳米颗粒的制备及其磁热效应

以乙酰丙酮金属盐为前驱体,三乙二醇为溶剂,采用多元醇法制备了镍锌不同配比的Ni_xZn_(1-x)Fe_2O_4(x=0,0.3,0.5,0.7和1.0)铁氧体,并通过X射线衍射仪(XRD),透射电子显微镜(TEM)和振动样品磁强计(VSM)等对样品的结构、形貌、磁性能和磁热性能进行了表征。结果表明:Ni_xZn_(1-x)Fe_2O_4铁氧体分散性较好,尺寸均一,形状近似球形,平均粒径为4~5 nm。Ni_xZn_(1-x)Fe_2O_4纳米颗粒在室温下表现出亚铁磁性,饱和磁化强度随着镍含量的增加先增大后减小,当x=0.5时达到最大值29.38 emu·g~(-1)。在382k Hz交变磁场作用下,Ni_(0.5)Zn_(0.5)Fe_2O_4铁氧体温度可升温至313 K,表现出较好的磁热性能。     

Synthesis of Fe3O4 particle-chain microwires in applied magnetic field

Fe₃O₄ particle-chain microwires are firstly synthesized under magnetic field by a simple coprecipitation method. The increase of magnetic field caused the lengthening of the wires, and doubled densities of starting solution lead to a halved diameter. It was supposed that the magnetic field gradient and the particular growing process of particles are the main factors of the formation of these microwires. Magnetic hysteresis curves of Fe₃O₄ microwires were also measured.     

柠檬酸根对纳米Fe3O4颗粒的生长及性能的影响

现代诊断学的发展使得超小超顺磁性的Fe₃O₄粒子在医学领域具有重要应用价值。实验中利用某些羧酸盐对铁氧化物晶粒成长的抑制作用，在共沉淀法中引入柠檬酸根，制备出平均粒径小于5 nm的Fe₃O₄纳米分散体系。研究了不同柠檬酸根浓度对生成粒子的大小、结晶和表面吸附情况的影响。对Fe₃O₄颗粒在不同条件下的磁性与胶体稳定性进行了讨论。     

Synthesis and morphology of an iron oxide/polystyrene/poly(isopropylacrylamide‐co‐methacrylic acid) thermosensitive magnetic composite latex with potassium persulfate as the initiator

In this work, an iron oxide (Fe₃O₄)/polystyrene (PS)/poly(N‐isopropylacryl amide‐co‐methacrylic acid) [P(NIPAAM–MAA)] thermosensitive magnetic composite latex was synthesized by the method of two‐stage emulsion polymerization. The Fe₃O₄ particles were prepared by a traditional coprecipitation method and then surface‐treated with either a PAA oligomer or lauric acid to form a stable ferrofluid. The first stage for the synthesis of the thermosensitive magnetic composite latex was to synthesize PS in the presence of a ferrofluid by emulsion polymerization to form Fe₃O₄/PS composite latex particles. Following the first stage of reaction, the second stage of polymerization was carried out with N‐isopropylacryl amide and methacrylic acid as monomers and with Fe₃O₄/PS latex as seeds. The Fe₃O₄/PS/[P(NIPAAM–MAA)] thermosensitive magnetic particles were thus obtained. The effects of the ferrofluids on the reaction kinetics, morphology, and particle size of the latex were discussed. A reaction mechanism was proposed in accordance with the morphology observation of the latex particles. The thermosensitive property of the thermosensitive magnetic composite latex was also studied. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3062–3072, 2007     

可循环磁性Pt/Fe3O4-MCNT催化剂上的肉桂醛选择性加氢反应

采用多步法依次将制备的Fe₃O₄纳米颗粒和Pt纳米颗粒负载到多壁碳纳米管(MCNT)上得到Pt/Fe₃O₄-MCNT磁性催化剂,以X射线衍射(XRD)、透射电镜(TEM)、超导量子干涉磁强计(SQUID)和热重-差热分析(TG-DTA)对Pt/Fe₃O₄-MCNT磁性催化剂的结构和磁性质进行了表征。研究发现预制备的Fe₃O₄纳米颗粒与Pt纳米颗粒均匀地分散于MCNT上,新制备以及多次使用后的Pt/Fe₃O₄-MCNT室温下都具有良好的超顺磁性。研究了Pt/Fe₃O₄-MCNT磁性催化剂上的肉桂醛选择性加氢反应,结果显示催化剂具有良好的C=O加氢活性,肉桂醛转化率在50%左右时,肉桂醇选择性可达96%以上。尺寸均一的Pt粒子均匀的分散在催化剂上可能是催化剂具有良好的C=O加氢选择性的重要原因。在外加磁场作用下催化剂可以高效地从液相反应体系中分离,经多次循环使用后仍具有良好的催化性能。     

Novel polyaniline-LiNi0.5La0.02Fe1.98O4 nanocomposites prepared via an in situ polymerization

Polyaniline (PANI)-LiNi_0.5La_0.02Fe_1.98O₄ nanocomposites were synthesized by an in situ polymerization of aniline in the presence of LiNi_0.5La_0.02Fe_1.98O₄ ferrite. The products were characterized by Fourier transform infrared (FTIR), atomic force microscopy (AFM), powder X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). FTIR spectra and XRD indicated the formation of the PANI-LiNi_0.5La_0.02Fe_1.98O₄ composites. AFM study was shown that the average size of samples was less than 100 nm and the ferrite particles had an effect on the morphology of composites. The nanocomposites under applied magnetic field exhibited the hysteresis loops of the ferrimagnetic nature, the saturation magnetization and the coercivity varied with the ferrite content. The bonding model for the composites was also studied.     

Thermosensitive and control release behavior of poly(N-isopropylacrylamide-co-acrylic acid)/nano-Fe3O4 magnetic composite latex particle that is synthesized by a novel method

In this study, a novel method was used to synthesize the poly(N-isopropylacrylamide-co-acrylic acid)/Fe₃O₄ (poly(NIPAAm-AA)/Fe₃O₄) magnetic composite latex. The crosslinked poly(NIPAAm-AA) polymer latex particles were first synthesized by the method of soapless emulsion polymerization, then Fe²⁺ and Fe³⁺ ions were introduced to bond with the -COOH groups of AA segments in poly(NIPAAm-AA) polymer latex particles. Further by a reaction with NH₄OH, Fe₃O₄ nanoparticles were generated in situ. The concentrations of acrylic acid (AA), crosslinking agent (N,N′-methylene bisacrylamide (MBA)), and Fe₃O₄ nanoparticles were important factors to influence the morphology and lower critical solution temperature (LCST) of poly(NIPAAm-AA)/Fe₃O₄ magnetic composite latex particles. The poly(NIPAAm-AA)/Fe₃O₄ latex particles were used as a thermosensitive drug carrier to load caffeine. The control release of caffeine was studies. Morphology-based schematic models were proposed to explain the control release behavior of the composite particles with different compositions. Moreover, the protein (albumin, acetylated from bovine serum (BSA)) was bound on the surface of poly(NIPAAm-AA)/Fe₃O₄ composite latex particles. The effects of AA, crosslinking agent and Fe₃O₄ contents on the amount of BSA binding were investigated at different temperatures and pH values. The composition-morphology-BSA conjugation relationship was established.     

可控粒径纳米Fe_3O_4的制备及其磁性研究

本文用空气氧化法,在可见光作用下,添加配合剂(EDTA、柠檬酸、酒石酸、谷氨酸)在室温进行了不同粒径纳米Fe3O4的制备及其磁性能研究。结果表明:在可见光作用下,随EDTA、柠檬酸、酒石酸、谷氨酸等配合剂的添加,得到纳米Fe3O4的粒径有所减小、分散性有所提高;配合剂及可见光共存时,体系反应速率得到提高,高的反应速率使纳米Fe3O4晶粒减小;控制适当的光照度和添加剂的量,室温可得到11.8~29.6nm的Fe3O4颗粒。不同粒径纳米Fe3O4分别呈现出超顺磁性、铁磁性特征。