镍负载量对邻氯硝基苯加氢制邻氯苯胺Ni/TiO2催化剂性能的影响

 用等体积浸渍法制备了一系列不同镍负载量的负载型Ni/TiO2催化剂,并将其应用于邻氯硝基苯加氢制邻氯苯胺的反应. 采用N2吸附、 X射线衍射、程序升温还原、透射电镜、 H2化学吸附及间歇加压釜式反应器活性评价等方法,考察了镍负载量对Ni/TiO2催化剂的物化性质及邻氯硝基苯加氢反应性能的影响. 结果表明,随着镍负载量的增加, Ni/TiO2催化剂上邻氯硝基苯的转化率逐渐提高; 当镍负载量超过30%时,催化剂的活性和选择性不再明显变化. 当催化剂中镍负载量高于20%时,在温度343 K、 氢压1.0 MPa和催化剂/邻氯硝基苯质量比1/10的条件下反应210 min后,邻氯硝基苯的转化率和邻氯苯胺的选择性均高于99%, 催化剂具有良好的应用前景. 分析表明,影响Ni/TiO2催化剂性能的主要因素为催化剂表面镍晶粒的活性表面积以及载体TiO2与金属镍之间的强相互作用.     

金属有机骨架材料负载镍纳米颗粒催化硝基苯加氢

以MIL-53(Al)、MIL-96(Al)和MIL-120(Al) (MIL: Material Institute of Lavorisier)三种金属有机骨架材料为载体, 采用浸渍法制备了负载廉价金属镍纳米颗粒的催化剂. 将其用于催化硝基苯加氢合成苯胺反应, 发现以MIL-53(Al)为载体制得的催化剂表现出优异的催化性能. 采用不同的镍前驱体, 如硝酸镍、醋酸镍、乙二胺合镍, 制备了一系列Ni/MIL-53(Al)催化剂. 通过X射线衍射、傅里叶变换红外光谱、电感耦合等离子体、N₂物理吸附、H₂程序升温还原、透射电镜等技术对其进行了表征, 研究了镍前驱体对金属-载体相互作用、镍颗粒尺寸以及分散程度的影响.结果表明:以乙二胺合镍为镍前驱体制得的催化剂具有金属-载体相互作用适中、镍纳米颗粒更小(4-5 nm)和分布更均匀的特点, 在硝基苯加氢反应中表现出优异的催化性能, 硝基苯转化率达到100%.回收重复使用5次后, 此催化剂仍保持催化活性,硝基苯转化率达92%.     

镍基催化剂上苯酐选择性加氢合成苯酞

分别以SiO2,TiO2,γ-Al2O3,TiO2-SiO2和TiO2-Al2O3为载体,以硝酸镍为镍源,采用等体积浸渍法制备了一系列镍基催化剂,并将其用于苯酐选择性加氢合成苯酞反应.结果表明,以TiO2-SiO2为载体制备的镍催化剂上Ni0活性组分分散度较高,催化剂表现出较高的活性和苯酞选择性.在此基础上,采用溶胶-凝胶法制备出了一系列Ni/TiO2-SiO2催化剂,考察了催化剂制备中各因素(包括溶剂、焙烧温度、还原温度和镍前驱体类型等)对其催化苯酐加氢反应性能的影响.结果表明,将镍前驱体溶于不同溶剂制备的催化剂性能差异很大,其中以水为溶剂制备的催化剂活性较高,且性能优于等体积浸渍法制备的相应催化剂.焙烧温度和还原温度过高会导致活性组分镍晶粒度变大,致使催化剂活性明显降低.镍源对Ni/TiO2-SiO2催化剂的性能影响较大,以硫酸镍为镍源制备的催化剂几乎无活性,而以氯化镍和硝酸镍为镍源制备的催化剂表现出较高的催化活性和选择性,其中以氯化镍制备的催化剂性能略高于硝酸镍,苯酐转化率为100%,苯酞选择性为88.5%.     

石墨烯负载镍催化CO_2加氢甲烷化

采用改进的Hummers法制备了氧化石墨烯(GO),经水合肼还原得到石墨烯(RGO),通过浸渍法制备了石墨烯负载的镍基催化剂(Ni/RGO);对其催化二氧化碳甲烷化反应的性能进行了研究,并与以碳纳米管(CNTs)和活性炭(AC)为载体负载的Ni基催化剂进行了比较.由于催化剂的载体分别为RGO,CNTs和AC,所以Ni将会表现出不同的形态.利用红外光谱(FTIR)、比表面积(BET)测试、程序升温还原(H2-TPR)、X射线衍射(XRD)分析和透射电子显微镜(TEM)等表征手段对其结构及物理性质进行了表征.结果表明,Ni/RGO具有相对较大的比表面积(316 m~2/g),Ni在Ni/RGO上的颗粒尺寸(5.3 nm)小于其在Ni/CNTs(8.9 nm)和Ni/AC(11.6 nm)上的颗粒尺寸;该催化剂在二氧化碳甲烷化反应中具有更高的催化活性和选择性,而且具有良好的使用寿命.     

TiO_2-Al_2O_3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO2-Al2O3复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H2原位还原法制备.通过N2吸附(BET)、X射线衍射(XRD)、透射电镜(TEM)、程序升温还原(TPR),X射线光电子能谱(XPS)和等离子体发射光谱(ICP-AES)表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能.结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al2O3的孔特征,具有较大的比表面积和较宽的孔分布,TiO2主要以表面富集的形式分散在管状的γ-Al2O3表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni2P和Ni12P5;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO2趋于在块状的Al2O3表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni2P.不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n(Ti)/n(Al)=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340℃,3 MPa,氢油体积比500,液时空速3 h-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

6-(3-氨基苯基)-4, 5-二氢哒嗪-3(2H)-酮的合成

以苯、丁二酸酐为原料,经傅克酰基化,硝化,与水合肼反应三步反应合成6-(3-氨基苯基)-4,5-二氢哒嗪-3(2H)-酮(1),总收率为58.3%。由3-(3-硝基苯甲酰基)丙酸(3)合成化合物1的过程中,在雷尼镍(Raney Ni)的催化下与水合肼反应,一步完成了苯环上硝基的还原和成环。重点考察了该步反应的物料配比、反应时间对产率的影响。结果表明,水合肼与化合物3的摩尔比11.7∶1,回流反应4 h,产率为82.7%。     

水合肼在还原制备苯胺类化合物中的专利技术进展

从专利角度出发,对水合肼作为还原剂,硝基苯类化合物还原制备苯胺类化合物的方法进行综述。对水合肼还原制备硝基苯的专利申请情况、主要申请人的申请情况进行了分析,对镍、钯、铁以及活性炭等催化剂在水合肼还原制备苯胺类化合物中的应用进行归纳和总结,且对活性炭作为催化剂的反应进行了概述,且对其发展趋势进行了展望。     

镍硅基催化剂上偏三甲苯的加氢脱烷基反应

分别采用溶胶-凝胶法和浸渍法制备了一系列Ni/SiO_2催化剂,将其用于催化偏三甲苯(1,2,4-TMB)的加氢脱烷基反应.结果表明,在制备过程中,无水柠檬酸(CA)的加入量对催化剂的结构、表面性质、粒径及催化性能均有较大影响.催化剂表面L酸位上1,2,4-TMB几乎不发生歧化和异构化反应.镍硅体系催化剂上主要副反应为苯环加氢,通过调整还原镍的粒径可有效控制苯环加氢,从而提高了二甲苯(BTX)的选择性.在最佳反应条件下,10Ni/Si-2.0催化剂上1,2,4-TMB的转化率最高为29.4%,BTX的选择性为99.9%.     

NiPt/SBA-15纳米催化剂的制备及其催化水合肼分解产氢性能研究

本研究采用浸渍还原法制备了不同金属比例的NiPt双金属负载SBA-15（介孔二氧化硅）催化剂,对其催化水合肼脱氢性能进行了研究。研究结果表明,在催化剂的制备过程中Pt和Ni形成了合金,两种金属的电子协同效应可以有效地促进催化剂的催化性能,SBA-15与金属活性组分之间的相互作用有助于改善催化剂的催化性能和循环稳定性。Pt6Ni4/SBA-15催化剂催化水合肼脱氢的反应活化能为45.6 kJ/mol,TOF值为2123.3 h-1,优于大部分已经报道的催化剂。     

镍负载量对乙醇水蒸气重整制氢催化性能和催化剂的影响

采用稳态实验对镍负载量对Ni/MgO催化剂在乙醇水蒸气重整反应的影响进行了研究。结果表明，在101.3kPa下，镍负载量越高，催化剂的活性越高。对于催化剂的选择性，存在一个最佳镍负载量为10%Ni/MgO。按选择性从大到小排序，不同镍负载量的催化剂为：10Ni/MgO>15Ni/MgO>12.5Ni/MgO>7.5Ni/MgO≈5Ni/MgO。热分析表明，焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。XRD和TPR 表征结果显示，催化剂的晶体结构和还原特性也与催化剂上镍的负载量有关。焙烧过程中样品10Ni/MgO上镍前体与载体前体发生了两种相互作用, 并且其氧化态与其他催化剂相比具有特殊的结构和还原性。说明催化剂的选择性不仅受活性相Ni的影响而且受Ni活性相周围环境的影响。     

Preparation of Sulphur-containing Aromatic Amines by Reduction of the Corresponding Aromatic Nitro Compounds with Hydrazine Hydrate over Iron Oxide Hydroxide Catalyst

The sulphur-containing aromatic amines are an important class of compounds frequently used as key intermediates in the synthesis of pharmaceutical products1,2, dyestuffs3-6 and polymers7. The usual methods for preparing sulphur-containing aromatic amines …     

Reduction of Sulphur-containing Aromatic Nitro Compounds with Hydrazine Hydrate over Iron(III) Oxide-MgO Catalyst

Sulphur-containing aromatic amines were prepared efficiently in good to excellent yields by reduction of the corresponding sulphur-containing aromatic nitro compounds with hydrazine hydrate in the presence of iron(III) oxide-MgO catalyst. The catalyst exhibited high activity and stability for the reduction of sulphur-containing aromatic nitro compounds. The yields of sulphur-containing aromatic amines were up to 91-99 % at 355 K after reduction for 1-4 h over this catalyst.     

Reduction of nitro derivatives of 1,3,4-oxadiazole

A method for the synthesis of amino derivatives of 1,3,4-oxadiazole by the reduction of the corresponding nitro compounds with hydrazine hydrate in the presence of Raney nickel in dioxane-ethanolic solution has been developed.     

Selective reduction of aromatic nitro compounds containing o- and n-benzyl groups with hydrazine and raney nickel

The selectiity in the catalytic reduction of aromatic nitro compounds containing O-benzyl, N-benzyl or chlorine with hydrazine and Raney nickel was studied.     

芳香硝基化合物还原制备芳胺的研究进展

综述了芳香硝基化合物还原制备芳胺的方法及近年的研究进展.其方法主要包括催化氢化法、CO/H2O还原法、金属还原法、硫化碱还原法、金属氢化物还原法、电化学还原法和光化学还原法.其中催化氢化法中的氢气还原法和水合肼还原法符合绿色化学的理念,并且反应收率高,选择性好,具有很高的应用价值.     

Reduction of 2-amino-3- and -5-nitropyridine derivatives with hydrazine hydrate

The reactions of 2-amino-3-nitropyridine and 2-amino-5-nitropyridine with hydrazine hydrate resulted in elimination of the amino group and reduction of the nitro group with formation of 3-aminopyridine. A probable reaction mechanism involves addition of hydrazine hydrate at the N-C² bond, followed by elimination of ammonia and reduction of the nitro group to amino. 2-Amino-4-methyl-3-nitropyridine and 2-amino-5-methyl-3-nitropyridine reacted with hydrazine hydrate in a similar way.     

One-step double reduction of aryl nitro and carbonyl groups using hydrazine

Single-step reduction of aryl nitro and carbonyl groups to the corresponding synthetically useful alkyl-anilines occurs with excellent yields by treatment with hydrazine and a base in a solvent-free reaction. The method has been applied to a broad range of compounds with different properties. Investigations into the mechanism of the reduction reveal that each group is reduced independently. A mechanism is proposed for this novel reduction of aromatic nitro groups.     

Highly efficient reduction of nitro compounds: Recyclable Pd/C-catalyzed transfer hydrogenation with ammonium formate or hydrazine hydrate as hydrogen source

Herein, we described a highly efficient heterogeneous Pd/C-catalyzed transfer hydrogenation of nitro compounds for the synthesis of primary amines, using ammonium formate and hydrazine hydrate as hydrogen source independently. The products were obtained with up to >99% yield. Furthermore, gram scale and recycling of catalyst had been tested with well results.     

Colloid and nanosized catalysts in organic synthesis: IV. Reduction of nitroarenes with hydrazine hydrate catalyzed with metal nanoparticles

Reduction of a series of nitroarenes with hydrazine hydrate catalyzed with colloid iron, cobalt, nickel, and copper particles has been studied. High catalytic activity of nickel and iron nanoparticles has been demonstrated. Special features of nitrobenzene reduction in the presence of cobalt particles have been revealed.     

A novel titanium-supported nickel electrocatalyst for cyclohexanol oxidation in alkaline solutions

A novel titanium-supported nickel electrode (Ni/Ti) is fabricated by a simple hydrothermal process using hydrazine hydrate as a reduction agent. Its electrocatalytic activity towards cyclohexanol oxidation has been investigated by cyclic voltammetry (CV), chronoamperometry (CA), quasi-steady state polarization and electrochemical impedance spectroscopy (EIS). Effects of various parameters such as potential scan rate and cyclohexanol concentration on the electro-oxidation of cyclohexanol are investigated. Results show that the Ni/Ti electrode behaves as an efficient catalyst for the electro-oxidation of cyclohexanol in basic media and its electrocatalytic activity towards cyclohexanol oxidation is higher than a nickel oxyhydroxide modified nickel electrode (NOMN). It is confirmed that during the anodic potential sweep the electro-oxidation of cyclohexanol follows the formation of NiOOH on the electrode surface and is then catalysed by NiOOH. The rate-determining step for cyclohexanol oxidation is the reaction between the high oxidation state nickel (Ni³⁺) and the adsorbed cyclohexanol on the surface of the Ni/Ti.