硼酸根与甲阶酚醛树脂中酚羟基和邻位羟甲基的螯合反应

通过溶液pH值的测定和红外光谱分析，研究硼砂与甲阶酚醛树脂水溶液的反应表明：在水溶液中硼砂能与甲阶酚醛树脂很快地发生反应；硼砂水解产生的B／（OH)4^-，以定量的方式与树脂中酚羟基和邻位羟甲基以共价配键相结合，形成具有四面体结构的螯合物，并放出H^ 离子。     

硼酸盐固化酚醛树脂

硼酸与多元醇的络合反应已被用于硼酸浓度的滴定分析、硼选择性树脂等[1 ] 。Ecolotec树脂是一种用硼酸盐固化的碱性酚醛树脂 ,制备时以KOH溶液为溶剂 ,以硼砂为交联剂 ,通入CO2 降低溶液 pH值而交联 ,因其固化快、无污染 ,可用作铸造用冷芯盒树脂砂粘结剂。加入硅烷偶联剂与增塑剂能大幅度提高树脂砂固化后的抗拉强度[2 ] ,以碱金属氧化物与氢氧化物作为促硬剂 ,也可以提高树脂砂强度[3] 。赵鹏等[4] 合成了G盐改性酚醛树脂 ,由该树脂得到的树脂砂固化后 2 4h强度高于Ecolotec树脂。谭晓明等[5 ,6] 发现 ,树脂与硼酸根离子的配位反应是…     

硼酸与多羟基化合物配位反应的热化学研究

用量热法在298.2 K测定了B(OH)~-_4与多羟基化合物的反应焓。计算了硼酸与多羟基化合物的配位焓和配离子的标准生成焓。根据配位焓确定了B(OH)~-_4与甘露醇、山梨醇、丙三醇、葡萄糖等多羟基化合物配位反应的配位数，B(OH)~-_4与甘露醇、山梨醇的配位数是2；与丙三醇、葡萄糖的配位数是1．     

褪色光度法测定芬顿体系中产生的羟自由基

建立了检测Fenton反应产生羟自由基的新方法。在pH3．5条件下，经自由基与甲基紫发生反应使甲基紫褪色，在580nm处用分光光度计测定其△A值的变化，可间接测定羟自由基的生成量。通过对测定条件的研究，得到最佳实验条件。甲基紫光度法稳定性好，可作为一种简便的筛选羟自由基清除剂的方法。     

4-取代-2,6-二(羟甲基)苯酚的选择氧化

酚类由于本身容易氧化,仅在非常温和的条件下才能直接使4-取代-2,6-二(羟甲基)苯酚中的羟甲基氧化成醛基。文献报道了用活性二氧化锰可以将2,6-二(羟甲基)-4-甲基苯酚氧化成2-羟基-5-甲基-1,3-苯二甲醛,但要使两个羟甲基中只有一个被氧化却是困难的。文献报道了由芳氧基溴化镁与甲醛作用制备水杨醛类化合物的方法,并认为中间产物是邻羟甲基苯酚的镁盐,后者与甲醛之间通过负氢离子转移的分子间氧化还原反应生成相应     

读者园地

问:三价金属离子与茜素络合剂如何进行反应?山东读者———张凡答:茜素络合剂(Alizarin Complexan)为羟基蒽醌类显色剂,是茜素(1,2-二羟基蒽醌)的衍生物,其化学名为二羧基甲氨甲基-1,2-二羟基蒽醌,或3-氨基-甲基茜素-N,N-二乙酸。由于其分子中含具有络合作用的亚甲基二乙酸,故俗称为茜素络合剂,其化学结构式如下:其中含4个可电离的H,故在书写时常简写作H4L。在水溶液中随pH值的增加,试剂分子中的4个H可相继脱去而形成不同价态的阴离子。在pH4左右时,首先脱去一个羧基上的H,成为H3L-阴离子,使溶液呈黄色;当pH值增至8左右,在2位上的羟基…     

三羟甲基氨基甲烷的合成

通过对羟甲基化反应条件的研究,找出了有效提高合成三羟甲基硝基甲烷产率的方法,即n(硝基甲烷)∶n(甲醛)=1∶3.2,Ca(OH)2溶液作催化剂,调节pH值至9左右,控温30℃反应4小时,得到三羟甲基硝基甲烷,产率达91.3%。在乙醇和二氯甲烷的溶剂中以水合肼为还原剂,加入催化剂还原硝基。将还原芳香族硝基化合物的方法应用到多羟基脂肪族硝基化合物上。     

新型聚合硼酸酯表面活性剂PBE的合成及其性能

以偶氮二异丁腈为引发剂,用N-羟甲基丙烯酰胺、硼酸三乙酯和N,N-二羟乙基十二烷基胺直接聚合合成了新型聚合硼酸酯表面活性剂PBE。采用红外光谱、核磁共振和凝胶色谱测试技术对其进行了结构表征;考察了PBE及其硼酸酯单体MBE的抗水解性、热稳定性、乳化力等性能,并由表面张力测定研究了PBE在不同溶液pH值下的表面性质。结果表明,由直接聚合合成反应,经提纯后可得白色或淡黄色固体粉末PBE,反应收率为77.2%,产物重均分子量可达Mw=28400g/mol。PBE抗水解性能强,热分解温度可达320℃,稳定性相比单体MBE有所提高。PBE的HLB值在10~13,其对石蜡油、松节油、甲苯和石油醚的乳化力明显优于单体MBE和乳化剂Tween-85。在25℃时,随溶液pH值的增大,PBE临界胶束浓度CMC明显降低,pH值在6~7时,CMC降低幅度最大,但溶液pH对γCMC影响较小;其中pH=7时,PBE临界胶束浓度CMC达到0.12g/L,γCMC为31.2mN/m,其表面活性与常规低分子量表面活性剂的应用水平相似,而优于聚乙烯醇、聚氧化乙烯-氧化丙烯嵌段共聚物Pluronic104等常规高分子表面活性剂。     

硼酸钠/甲阶酚醛树脂配合物的热固化过程和耐热性

硼酸钠/甲阶酚醛树脂配合物的热固化过程和耐热性     

基于取代硼酸化学的新颖生物分子萃取、分离和样品预浓缩方法

取代硼酸与邻二羟基化合物的化学反应早在160年前就被人们所认识.取代硼酸能与邻二羟基化合物专一性地反应,生成五元或六元环的酯.该反应为pH控制的可逆反应:反应物在碱性pH值下结合,产物在酸性pH值下解离.这样的特征使得取代硼酸可以作为分子识别的优良配基.根据这一反应,用于检测和分离邻二羟基化合物的化学传感器和硼亲和色谱分别在上世纪60年代和80年代出现.     

Studies on synthesis,characterization and adhesive strength evaluation of KFA substituted resole adhesives

Preliminary investigations revealed the presence of appreciable amount of gum rich in lignin and tannin in kendu fruit (Diospyros Cordifolia Roxb). The kendu fruit adhesive (KFA) was used to substitute phenol in resole formulations to achieve cost effectiveness. Substituted resole formulations with 50 and 100% KFA were prepared in alkaline medium through stepwise addition process. Unsubstituted and KFA substituted resole adhesives were then characterized by FT‐IR, thermogravimetric analysis, differential scanning calorimetry and X‐ray diffraction analysis. The adhesive strength of the above mentioned formulations were evaluated by comparing the results of mechanical tests as per the ASTM specifications using UTM‐LR‐100K LLOYD Instruments, UK. Analytical characterizations revealed the substitutions of phenol by KFA in the substituted resole formulations. The results of adhesive strength test revealed that the 50% KFA substituted PF resin exhibits better adhesive strength than the virgin phenol‐formaldehyde and 100% KFA‐formaldehyde resole formulation. Copyright © 2001 John Wiley & Sons, Ltd.     

FTIR研究不同固化程度SiO_2/酚醛杂化材料官能团的变化

采用FTIR光谱吸收峰的波数位移、A/A1612表示的吸收强度和半峰宽Δ1/2(O—H)/Δ1/2(C C)表示的谱带宽度,比较不同固化程度SiO2/酚醛树脂杂化材料官能团的变化.在相同固化条件下(120℃,2 h),杂化材料的氢键作用比酚醛树脂的强得多,羟基含量更高,而且杂化材料发生邻位取代缩合反应的比例特别高.正是因为杂化材料中未反应的官能团多,作为底漆使用时能与面漆中的官能团反应,实现无层间界面交联,获得层间结合力.过固化过程(160℃,1 h)能够有效降低杂化材料中的羟基含量,但醚键含量比酚醛树脂的高得多,而且过固化过程中酚环主要发生对位取代缩合反应.杂化材料固化后的颜色比热固性酚醛树脂的淡得多,与热塑性酚醛树脂的相当.在相同氧化程度下,杂化材料中无游离酚,比酚醛树脂更环保.     

Effect of three boron flame retardants on thermal curing behavior of urea formaldehyde resin

The purpose of the study was to investigate the effects of three kinds of flame retardant (FR), boric acid, zinc borate, and borax on the thermal curing behavior of urea–formaldehyde (UF) resin. Both pH value and gel time were measured to study the curing characters of the UF resin with different loading levels of FR. In addition, differential thermal analysis was also used to obtain kinetic analyses parameter. The results showed that boric acid decreased pH value of UF resin, and reduced gel time of the UF resin. There are no significant changes of the UF resin curing characters with different loading levels of FR. The activation energies for curing reaction of UF resins in the presence of boric acid, zinc borate, and borax, were 84.37, 84.41, and 118.4 kJ/mol, respectively, higher than that of the control one (75.38 kJ/mol). All FRs showed adverse effect on the curing behavior of the UF resin.     

Addition Mechanisms of Phenol toward Formaldehyde under Acidic Condition： a Theoretical Investigation

The reaction mechanisms of phenol with formaldehyde in the first and second addition at the ortho- and para-position in acid solution were theoretically investigated at the PW91/DNP level with solvent effects included. The reaction of phenol with protonated methanediol firstly forms an adduct intermediate, via a SN2 mechanism with a water molecule as the leaving group. From the adduct intermediate, there are two reaction channels involving a proton transfer to form the addition products. One is that a proton directly transfers via a four-membered ring transition state with a notable energy barrier (Four-member mechanism). Another mechanism involving a water molecule as catalyst to mediate the proton transfer (WCP mechanism), is a barrierless process, indicating that the formation of the adduct intermediate, the first reaction step, is rate-limiting. The reaction products are free hydroxymethyl phenols and/or hydroxybenzy carbocation (HOC6H4CH2+) which plays an important role in the following formation of methylene and methylene ether linkages. The second addition reactions between formaldehyde and hydroxymethyl phenol at all possible reaction sites of the phenol ring in acid solution were also investigated and discussed.     

高残炭硼酚醛树脂的制备

酚醛树脂(PF)因其具有良好的耐热性能和机械性能而被广泛应用。但其耐热性能已经满足不了现代航空航天技术的需求,研究发现,采用硼酸对酚醛树脂进行改性,可以制得具有优良耐高温性能的硼酚醛树脂(BPF)。采用硼酸酯法合成硼酚醛树脂,n(苯酚)∶n(甲醛)=1∶1.5时耐热性最佳。热分析结果表明,合成的BPF在1000℃条件下的残炭率为78%,其耐热性能明显优于传统的酚醛树脂。同时讨论了不同硼酸含量对BPF耐热性能的影响,当n(硼酸)∶n(苯酚)0.33∶1时,残炭率趋于稳定。此外,利用差示扫描量热仪(DSC)方法确定BPF预固化温度为160℃,后固化温度为220℃。     

Analysis of resoles by gel-permeation chromatography

Resoles, the complex, heat-sensitive product mixture from the alkali-catalyzed reactions of phenol with formaldehyde were investigated by gel-permeation chromatography (GPC). The low molecular weight species of these resins which consisted of mono-and dinuclear methylol phenols were resolved into multiple peaks. Model compounds were used to identify the peaks of the specific methylol phenols or methylene etherbridged diphenols. Differences in the refractive index of individual species restricted the quantitative analysis of low molecular weight components in the resole. The effects of sodium and barium hydroxides and hexamethylene-tetramine as catalysts, reaction temperature, and time on the total composition of a resole are demonstrated with the gel-permeation chromatographic spectrum and with the aid of NMR. Formation of a “secondary” resole by methylolation of the bisphenol of formaldehyde was also monitored by GPC.     

毛细管电泳中葡萄糖-羟丙基甲基纤维素体系分离脱氧核糖核酸

葡萄糖作为羟丙基甲基纤维素（Hydroxpropylmethyl cellulose,HPMC)筛分体系的添加剂,可以改善该体系在低浓度时分离脱氧核糖核酸（DNA）的能力。研究了硼酸浓度和pH值对葡萄糖－羟丙基甲基纤维素体系分离性能的影响;并将葡萄糖与其它添加剂如甘油、甘露醇对分离的影响作了比较,葡萄糖特有的环状结构使得其对羟丙基甲基纤维素体系分离能力的提高更为显著。     

Structural characteristics of p‐t‐Octylphenol formaldehyde resole resins using molecular simulation

p‐t‐Octylphenol formaldehyde resole resins have two linkage types of methylene‐ and dimethylene ether‐linkages and have three terminal types of hydrogen, methylol, and o‐methylene quinone. Variation of structural characteristics of the resins due to different types of linkages and terminals were studied using molecular dynamics and molecular mechanics. The structural characteristics of the methylene‐bridged resins were intramolecular hydrogen bonds between hydroxyl groups of the adjacent p‐t‐octylphenols. In the dimethylene ether‐bridged resin, the intramolecular hydrogen bonds between oxygen atoms of the dimethylene ether‐linkages and hydroxyl groups of the neighboring phenolic units were found. For the resins with both methylol terminals, one of both terminals of the resins was hidden at the center of the molecule when the resin size is large. The number of hydrogen bonds in the resins with the methylol terminal was larger than for the resins with the o‐methylene quinone terminal. Variation of the structural characteristics of the resins by dehydration of the terminal methylol was discussed. Using the calculated results, dissociation of the dimethylene ether linkage and crosslinking reaction of rubber chains by the resin were explained. Copyright © 2002 John Wiley & Sons, Ltd.     

Curing kinetics of boron‐containing phenol–formaldehyde resin formed from paraformaldehyde

A boron‐containing phenol–formaldehyde resin (BPFR) was synthesized from boric acid, phenol, and paraformaldehyde. The curing reaction of BPFR was studied by Fourier‐transform infrared spectrometry and differential scanning calorimetry. According to the heat evolution behavior during the curing process, several influencing factors on isothermal curing reaction were evaluated. The results show that the isothermal kinetic reaction of BPFR follows autocatalytic kinetics mechanism, and kinetic parameters m, n, k₁, and k₂, were derived, respectively. In the latter reaction stage, the curing reaction becomes controlled mainly by diffusion. © 2002 Wiley Periodicals, Inc. Int J Chem Kinet 34: 638–644, 2002