壳聚糖固定化血管紧张素转化酶及其性质

以壳聚糖微球为载体, 戊二醛为交联剂固定化血管紧张素转化酶, 研究了酶固定化的最优条件和固定化酶的性质. 结果表明, 在戊二醛质量分数为2.5%、给酶量为8 mg/mL时, 固定化酶的比活性最大, 为0.085 U/g. 固定化酶在40~50 ℃, pH在7~9之间有最大活性, 其米氏常数Km为2.39 mmol/L. 同时, 固定化酶具有良好的稳定性, 可重复利用.     

基于固定化酶的乙酰胆碱酯酶抑制剂体外筛选模型的建立

以可重复使用的固定化酶代替游离态酶, 建立一种基于比色分析的乙酰胆碱酯酶(AChE)抑制剂体外筛选新模型. 采用以氨基化硅胶为载体固定的AChE优化了实验条件, 用AChE抑制剂阳性对照物他克林和毒扁豆碱对该模型进行验证, 还对模型技术参数进行评价, 并将新模型用于单体化合物及天然产物粗提物AChE抑制活性评价. 结果表明, 最佳实验条件为: 固定化酶用量55 μL, 底物浓度5 mmol/L, 甲醇、 乙醇及体积分数不高于6%的二甲基亚砜水溶液均可作为样品溶剂; 模型验证及模型技术参数评价结果良好, 该模型对AChE抑制剂筛选有较好的特异性和灵敏度, 可用于筛选AChE抑制剂. 该模型具有适用性强、 固定化酶可重复使用及结果可靠等优点, 是单体化合物及天然产物粗提物AChE抑制剂活性评价的有效方法.     

自组装磁性聚苯乙烯微球固定化木瓜蛋白酶

通过逐层自组装（Layer-By-Layer self-assembly）的方式在自制的经过磺化的聚苯乙烯微球上连接高分子电解质和磁性物质制备了磁性微球,并用此磁性微球固定化木瓜蛋白酶。研究了固定化酶的最优工艺条件（固定化率最高）为：0.5g液态分散磁球(固含量为7.9%),温度30℃,给酶量15mg,pH值为6.0,固定化时间1.0h,此时可达非常高的固定化率93.0%。并且研究了固定化酶的性质：最佳使用温度为50℃,最佳使用pH值8.0,使用3次或80℃保存1.5~2.0h活性大约降为一半。     

固定化木瓜蛋白酶的制备和性质研究

多孔硅球固定化木瓜蛋白酶具有热增活性 .本文在前文研究的基础上 ,用载体交联法制备了甲壳胺固定化木瓜蛋白酶和纤维素固定化木瓜蛋白酶 .考察了固定化pH值、戊二醛浓度和给酶量对固定化木瓜蛋白酶活力的影响 .研究了固定化木瓜蛋白酶的性质 ,特别是热稳定性和耐热性 ,并与溶液酶和多孔硅球固定化木瓜蛋白酶进行了比较 .所制得的甲壳胺固定化木瓜蛋白酶和纤维素固定化木瓜蛋白酶的最适反应温度均达到了 80℃ ;90℃温育 1h后固定化酶的活力保持在 95 %以上 ;70℃温育处理 5h和 6h后固定化酶的活力也仍能保持在 90 %以上 .固定化木瓜蛋白酶的热稳定性和耐热性得到了显著提高     

壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶及其性质

以具柔性亲水手臂的壳聚糖-精氨酸树脂为载体,用戊二醛交联胰凝乳蛋白酶,获得壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶. 最佳固定化条件为:m(酶)∶ m(载体)=20∶ 1 000、戊二醛体积分数为1.0%、pH=5.20、30 ℃交联60 min. 固定化酶活力达850 U/g,Km为1.83 mmol/L,比游离酶增大33.6%,比交联壳聚糖固定化酶低24.0%. 壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶水解时间进程曲线与游离酶基本一致,均在反应30 min达到最大速率,最适温度为70 ℃,比游离酶升高10 ℃;在75 ℃时的半衰期可达6.0 h,比游离酶提高约4.3倍;最适pH值为5.92,比游离酶向酸性偏移2pH单位. 4 ℃贮存半衰期为49 d.     

壳聚糖固定化乳酸脱氢酶的制备及酶学性质研究

以磁性壳聚糖作为载体,戊二醛作为交联剂,对乳酸脱氢酶(LDH)进行固定化.固定化的最适条件为:戊二醛浓度6%,pH值7.5,酶的偶联时间2 h.对游离及固定化LDH酶学性质的研究表明,酶促反应的最适pH值为9.2,最适温度分别为37℃和50℃,对乳酸的表观米氏常数分别为1.6 mmol/L和0.9 mmol/L.游离酶和固定化酶在40℃放置150 min后,其活力分别为最初的56.5%和76.1%.固定化酶在4℃贮存4周后,活力仍保留50%以上.固定化酶在室温下与底物重复反应6次后,活力仍保留60%以上,说明固定化酶具有较好的热稳定性、贮存稳定性和复用性.     

壳聚糖固定化醇脱氢酶的制备及其酶学性质研究

报道了醇脱氢酶(ADH)的固定化和酶学性质研究。以壳聚糖作为载体,戊二醛作为交联剂。固定化ADH的最适条件为:以6%戊二醛将壳聚糖交联2 h,与ADH反应2.5 h。对游离和固定化ADH酶学性质的研究表明:酶促反应的最适pH均为8.2,最适温度分别为37℃和40℃,对乙醇的表观米氏常数Km分别为33.9 mmol/L和46.2 mmol/L。与游离酶相比,固定化酶具有良好的操作稳定性。     

京尼平交联磁性壳聚糖微球的制备及其脂肪酶的固定化

采用反相悬浮法与溶胶凝胶法结合制备磁性壳聚糖微球,并以此为载体,京尼平为交联剂,脂肪酶为模型酶进行固定化,研究了酶固定化的最优条件和固定化酶的性质。结果表明,在京尼平浓度为0.6 g/L、交联温度为55 ℃、交联时间8 h,固定化酶的比活力最大,为4.31 U/g。固定化酶在25~35 ℃,pH值在8.0有最大活性,其米氏常数Km为0.26 mol/L。同时,固定化酶具有良好的热稳定性及pH稳定性,可重复利用,且能进行磁分离。     

阳离子交换树脂吸附交联固定鸡肝酯酶的实验研究

研究了基于酶抑制原理的农药残留生物传感器中固定化酶的制备方法.以离子交换树脂作为固定化载体,戊二醛为交联剂,采用吸附交联相结合的方法制备了固定化鸡肝酯酶.在 10℃下吸附75min,以及酶活力浓度固定在6U/ml±2U/ml,在交联过程中戊二醛浓度0.04%,10℃下交联1h的条件下可以获得最佳的固定效果.并且,用吸附交联制得的固定化酶相对于用吸附法制得固定化酶用于流动分析过程,其热稳定性和耐冲刷性更好.同时,在保存阶段也具有更好的稳定性.     

含氨基和环氧基双功能基的聚合物刷磁性微球的制备及对青霉素G酰化酶的固定化

在内部分散超顺磁性Fe3O4纳米粒子的二乙烯苯交联聚丙烯酸微球表面引入原子转移自由基聚合(ATRP)引发剂,引发聚合向微球表面分别引入P(GMMA-r-DMAEMA-r-GMA)、P(GMMA-r-DMAEMA)和P(GMMA-r-GMA)无规共聚物刷(GMMA为甲基丙烯酸甘油单酯,DMAEMA为甲基丙烯酸-N,N-二甲氨基乙酯,GMA为甲基丙烯酸缩水甘油酯),聚合物刷中GMMA链节的作用是使聚合物刷具有亲水性,DMAEMA引入氨基,GMA引入环氧基.研究了青霉素G酰化酶在这些载体上的固定化和其酶活性.结果表明,同时引入环氧基和氨基的P(GMMA-r-DMAEMA-r-GMA)刷磁性微球固定化青霉素G酰化酶的活性和活性收率都最高,其固定化动力学比只含环氧基P(GMMA-r-GMA)刷磁性微球的好.固定化酶比自由酶更耐热,固定化酶的最佳pH值比自由酶的略高,固定化酶重复使用10次后其活性保留70%.     

一种简化的重氮化法制备固定化酶的载体合成方法

重氮化法是固定化酶时常用的一种方法。用多孔玻璃等无机物作载体时,一般是先用g-氨丙基三乙氧基硅烷与多孔玻璃等载体反应[1,2],生成烷基胺玻璃,然后与对硝基苯酰氯反应,产物经过还原,生成带有芳胺的衍生物,最后进行重氮化。本文通过烷基胺与对氨基苯甲酸反应,直接生成芳胺的衍生物,比常用的方法缩短了一步。通过在新合成的载体上对木瓜蛋白酶进行固定化,研究了固定化条件对酶活力回收的影响,最适固定化条件如下:pH为7.0,时间为6h,酶量为240mg/g载体,并比较了固定化酶和溶液酶的有关性质,考察了固定化酶的操作稳定性。结果表明,用这种方法合成的载体固定化酶,其对热稳定性、操作稳定性及产率都比较理想。     

Covalent immobilization of glucose oxidase onto new modified acrylonitrile copolymer/silica gel hybrid supports

New polymer/silica gel hybrid supports were prepared by coating high surface area of silica gel with modified acrylonitrile copolymer. The concentrations of the modifying agent (NaOH) and the modified polymer were varied. GOD was covalently immobilized on these hybrid supports and the relative activity and the amount of bound protein were determined. The highest relative activity and sufficient amount of bound protein of the immobilized GOD were achieved in 10% NaOH and 2% solution of modified acrylonitrile copolymer. The influence of glutaraldehyde concentration and the storage time on enzyme efficiency were examined. Glutaraldehyde concentration of 0.5% is optimal for the immobilized GOD. It was shown that the covalently bound enzyme (using 0.5% glutaraldehyde) had higher relative activity than the activity of the adsorbed enzyme. Covalently immobilized GOD with 0.5% glutaraldehyde was more stable for four months in comparison with the one immobilized on pure silica gel, hybrid support with 10% glutaraldehyde and the free enzyme. The effect of the pore size on the enzyme efficiency was studied on four types of silica gel with different pore size. Silica with large pores (CPC-Silica carrier, 375 A) presented higher relative activity than those with smaller pore size (Silica gel with 4, 40 and 100 A). The amount of bound protein was also reduced with decreasing the pore size. The effect of particle size was studied and it was found out that the smaller the particle size was, the greater the activity and the amount of immobilized enzyme were. The obtained results proved that these new polymer/silica gel hybrid supports were suitable for GOD immobilization.     

Enzyme inhibitor screening by electrospray mass spectrometry with immobilized enzyme on magnetic silica microspheres

In this study, a novel technique for screening inhibitors by electrospray mass spectrometry (ESI-MS) with immobilized enzyme on magnetic microspheres has been demonstrated. First, the model enzyme acetylcholinesterase (AChE) is immobilized onto the 3-glycidoxypropyltrimethoxysilane (GLYMO)-modified magnetic silica microspheres. AChE activity was monitored by biochemical assay that is based on mixing of AChE immobilized microspheres and model substrate acetylcholine, separating and detecting the product through ESI-MS. Stability of the enzyme-immobilized microspheres was investigated. No apparent loss of enzyme activity was observed after fivefold reuse of AChE-immobilized microspheres. The enzyme-immobilized bioassay was used to effectively identify AChE inhibitors among two standard samples, huperzine A and huperzine B, and their source herbal Huperzia serrata, all of which were spiked into the substrate. The inhibition was determined by measuring a decrease of product formation using ESI-MS.     

Properties of Immobilized Laccase on Mesostructured Cellular Foam Silica and its Use in Dye Decolorization

Laccase was immobilized on mesostructured cellular foam (MCF), a kind of mesoporous silica with large pore size by adsorption–cross linking method. The effects of immobilization time, temperature, pH, amount of enzyme and content of glutaraldehyde on the immobilization were optimized. The activities and stabilities towards pH and temperature of the immobilized enzyme were studied, and significantly improved enzymatic properties and good operational stability were obtained for the immobilized laccase. Dye decolorization tests showed that the immobilized enzyme could decolorize Alizarin Red and Indigo Blue solution fast and efficiently in the presence of ABTS.     

壳聚糖–精氨酸树脂固定化胰凝乳蛋白酶及其性质

以自制的多孔、具柔性亲水手臂的壳聚糖–精氨酸树脂为载体,戊二醛为交联剂固定胰凝乳蛋白酶,确定了酶与载体的最佳比例为20 mg酶/g湿树脂,交联剂的最佳用量为10 mL 1.0%戊二醛/1.5 g湿树脂,交联时间为60 min,所得固定化酶的活力回收率达68.95%。固定化胰凝乳蛋白酶的Km为8.36 mg/mL,比游离酶增大1.52倍,其酶促反应10 min达到最大速率,具有接近游离酶的催化时间进程曲线;其最适温度为70 ℃,比游离酶升高10 ℃;其最适pH值为5.92,比游离酶酸性偏移2个pH值。此外,固定化胰凝乳蛋白酶具有良好的热稳定性和贮存稳定性,75 ℃时的半衰期为8 h,4 ℃时的半衰期为46天。