含甲基丙烯酸-N,N-二甲氨基乙酯水凝胶的紫外辐射合成及其性质研究

紫外光辐照 ,H2 O2 为光引发剂 ,N ,N′ 亚甲基双丙烯酰胺为交联剂合成了含甲基丙烯酸 N ,N 二甲氨基乙酯的水凝胶 .研究了水溶液中单体、光敏引发剂、交联剂浓度及光照时间对生成的水凝胶的凝胶含量和溶胀性能的影响 ,给出了最佳合成条件 .用该聚合法合成的聚甲基丙烯酸 N ,N 二甲氨基乙酯水凝胶不仅具有较好的透明性和适当的弹性 ,而且在 40℃和 pH =3时有明显的温度及 pH敏感性 .但离子强度对凝胶溶胀性能没有明显影响     

甲基丙烯酸N,N-二甲氨基乙酯与丙烯酰β-环糊精共聚水凝胶的合成及其性能研究

用不同的方法合成了两种结构不同的丙烯酰 β 环糊精酯 (β CD 3 A和 β CD 6 A) ,以此为单体与甲基丙烯酸N ,N 二甲氨基乙酯 (DMAEMA)通过氧化还原自由基引发聚合 ,合成出两类含 β 环糊精结构单元的新型水凝胶 .用核磁共振 ,红外光谱及元素分析对两种单体及共聚物的结构和组成进行了表征 .溶胀实验结果表明 ,两类水凝胶均具有较好的pH、温度及离子强度敏感性 ,且因其交联网络结构不同 ,其溶胀性能有所差异     

快速pH响应丝胶/聚甲基丙烯酸互穿网络水凝胶的合成及表征

采用同步互穿网络方法制备丝胶蛋白(SS)/聚甲基丙烯酸(PMAA)为组分的互穿网络(IPN)水凝胶. 研究了互穿网络水凝胶对介质pH的刺激响应性能. 结果表明, IPN水凝胶具有强烈的pH刺激响应性能. 在pH=9.2的缓冲溶液中, -COOH解离成 -COO^-, 渗透压与网络之间的静电排斥作用导致IPN的溶胀度增大; 当pH减小时, 溶胀度随之减小. IPN水凝胶具有快速退溶胀速率及可逆溶胀-收缩性能.     

聚(N,N′-二乙基丙烯酰胺)水凝胶的制备及其溶胀动力学

以N,N′-二乙基丙烯酰胺(DEA)为单体,偶氮二异丁腈(AIBN)为引发剂,分别采用疏水性的1,2-二乙烯苯(DVB)和水溶性的N,N′-亚甲基双丙烯酰胺(BIS)为交联剂制备了温度敏感水凝胶聚(N,N′-二乙基丙烯酰胺)(PDEA).制得的PDEA水凝胶的低临界溶解温度(LCST)在30 ℃附近,初步讨论了交联剂的用量和性质对水凝胶性能的影响.并对其在不同温度下达到溶胀平衡时的溶胀比,去溶胀动力学及干凝胶的再溶胀动力学过程进行了研究.     

温度/pH敏感性接枝共聚物水凝胶P(DMAEMA-g-NIPAM)的 合成及性质研究

利用大分子单体技术, 采用自由基溶液聚合合成了温度/pH敏感性聚甲基丙烯酸-N,N-二甲氨基乙酯接枝聚N-异丙基丙烯酰胺[P(DMAEMA-g-NIPAM)]水凝胶. 用红外光谱及扫描电镜对凝胶的组成及形貌进行了表征. 凝胶的去溶胀和溶胀动力学研究表明, 所合成的凝胶具有温度和pH敏感性. 与传统的聚丙烯酸系水凝胶相比, P(DMAEMA-g- NIPAM)具有相反的pH敏感性; P(DMAEMA-g-NIPAM)凝胶在55 ℃时具有较快的去溶胀速率, 随着凝胶中接枝链PNIPAM量的增加, 凝胶的去溶胀速率加快.     

P(AMPS-co-BMA)水凝胶的电场敏感性及电刺激响应机理

以离子型单体2-丙烯酰胺-2-甲基丙磺酸(AMPS)及非离子型单体甲基丙烯酸丁酯为原料, 偶氮二异丁腈为引发剂, N,N′-亚甲基双丙烯酰胺为交联剂, N,N-二甲基甲酰胺为溶剂, 通过自由基聚合合成了一系列聚离子浓度不同的聚(2-丙烯酰胺-2-甲基丙磺酸-co-甲基丙烯酸丁酯)电场敏感性水凝胶. 研究了其在去离子水及NaCl溶液中的溶胀行为. 结果表明, 该水凝胶在去离子水中的平衡溶胀度在236.4~298.5之间, 其溶胀速率随着AMPS用量的增加而增加; 并且随着凝胶内部聚离子浓度的增加, 凝胶在NaCl溶液中的消溶胀速率及消溶胀度逐渐减小. 凝胶的电刺激响应性能研究结果表明, 在电场存在下, 凝胶在NaCl溶液中的溶胀行为与凝胶内部聚离子浓度和溶液中NaCl浓度的相对大小有关, 当凝胶内部聚离子浓度大于溶液中NaCl浓度时, 凝胶溶胀, 反之则凝胶消溶胀; 而且, 凝胶在电场作用下的偏转行为同样与凝胶内部聚离子浓度和溶液中NaCl浓度的相对大小有关, 当凝胶内部聚离子浓度大于溶液中NaCl浓度时, 偏向阴极, 反之则凝胶偏向阳极. 另外, 在电场存在下, 凝胶在NaCl溶液中的电偏转速度与环境温度密切相关.     

pH敏感的聚(L-谷氨酸)-交联聚丙烯酸水凝胶的合成与性能研究

通过在聚L-谷氨酸侧链部分接枝甲基丙烯酸2-羟乙酯得到含有双键的聚(L-谷氨酸),将其与丙烯酸共聚得到由聚(L-谷氨酸)侧链接枝并交联聚丙烯酸的pH敏感水凝胶.研究水凝胶在不同pH的缓冲溶液中的溶胀性、溶胀动力学,并通过SEM观察水凝胶的微观结构.结果表明,水凝胶在低pH环境下的溶胀率明显低于高pH环境中的溶胀率,不同...     

PAMPS/SiO_2杂化水凝胶的合成及电场敏感性研究

以2-丙烯酰胺-2-甲基丙磺酸(AMPS)为有机原料,正硅酸乙酯(TEOS)为无机原料,过硫酸钾为引发剂,N,N'-亚甲基双丙烯酰胺为交联剂,通过原位-凝胶水溶液聚合法合成了一系列不同二氧化硅含量和不同聚离子浓度的聚(2-丙烯酰胺-2-甲基丙磺酸)/二氧化硅杂化电场敏感性水凝胶.通过扫描电子显微镜(SEM)表征凝胶的结构,研究水凝胶在去离子水以及氯化钠溶液中的溶胀和消溶胀行为.结果表明,系列凝胶的平衡溶胀度介于224.9至325.6之间,复合凝胶的溶胀速率随TEOS用量的增加而降低;除理想杂化凝胶外,随着聚离子浓度的升高,凝胶在氯化钠溶液中的消溶胀速率逐渐减小.对凝胶的电场敏感性研究表明,当聚离子浓度大于氯化钠溶液浓度时,凝胶进一步溶胀,反之则消溶胀,其中杂化凝胶的再溶胀性能减弱,而消溶胀行为变得更为明显.同时制得的理想杂化凝胶,较纯有机凝胶具有更为理想的力学性能,最大抗压缩强度可达23.4 MPa.     

聚N-异丙基丙烯酰胺/纳米SiO_2复合水凝胶的合成及溶胀性能

通过纳米SiO2的表面功能化,在其表面引入乙烯基功能基团,在H2OTHF的混合溶剂中,超声分散后,交联剂N,N′亚甲基双丙烯酰胺存在时,于25℃下使其与N异丙基丙烯酰胺共聚,制得聚N异丙基丙烯酰胺纳米SiO2复合水凝胶,并用FTIR和SEM对产物进行了表征.研究了凝胶的溶胀动力学,消溶胀动力学和温度敏感性.实验结果表明,纳米SiO2的引入,改善了聚N异丙基丙烯酰胺水凝胶在低温时的溶胀性能和在高温时对水的释放性能,并讨论了引起这些性能改变的原因.     

pH敏感水凝胶P(St-DVB-MAA)合成及性能评价

以聚乙烯醇为分散剂,过氧化苯甲酰为引发剂,苯乙烯和α-甲基丙烯酸为单体,二乙烯基苯为交联剂,在80℃下,采用自由基沉淀聚合法制备了pH敏感水凝胶P(St-DVB-MAA)通过傅里叶红外光谱和热重仪对聚合物进行了表征及结构分析,研究了时间、pH、盐溶液对水凝胶P(St-DVB-MAA)溶胀行为的影响,并重点探讨了水凝胶P(St-DVB-MAA)溶胀率和离子吸附能力的关系,使用P(St-DVB-MAA)为基质的阳离子交换树脂对合成废水中的锌离子进行了吸附试验,考察了离子交换性能。结果表明,P(St-DVB-MAA)具有较好的pH响应性,其溶胀率与离子交换吸附能力密切相关。     

超声衰减检测法研究大分子构象变化

以壳聚糖(CS)包埋聚N－异丙基丙烯酰胺(PNPAM)水凝胶和聚甲基丙烯酸(PMAA)水溶液为模型体系,研究了超声衰减检测法用于探测大分子溶液构象和聚集态变化的可能性,实验表明,超声衰减参量(a)与大分子在溶液或水凝胶中的构象状态密切相关。一般而言,大分子的松散线团构象具有较低的超声衰能力,而压缩线团构象则具有比较高的超声衰减能力,不过,过度压缩线构象的超声衰减能力也比较小。据此,可以预期超声减检测有可能发展成一种简单、非破坏性大分子构象研究新方法。     

Novel route to synthesis of allyl starch and biodegradable hydrogel by copolymerizing allyl‐modified starch with methacrylic acid and acrylamide

Maize starch was modified by allyl chloride adopting an interfacial reaction technique with cetyltrimethyl ammonium bromide as a phase‐transfer catalyst and pyridine as an acid acceptor. The degree of substitution was determined from an increasing carbon content of the modified starch. The percentage of carbon and hydrogen of the allyl‐modified starch was estimated by elemental analysis (C, H, and N), and the product characterization was done through ¹H NMR and ¹³C NMR analyses. The allyl‐modified starch was then copolymerized with methacrylic acid and a combination of methacrylic acid and acrylamide at 50 and 70 °C with potassium persulfate as an initiator. The copolymer thus formed swelled in distilled water after neutralization with sodium carbonate. The percentage of absorption capacity of the hydrogels was determined with distilled water and 0.9% NaCl solution. The highest percentage of absorption, 6500%, was achieved for the developed hydrogel containing allyl starch and acrylic monomer in a 1.7:1 w/w ratio and acrylic monomer, namely, methacrylic acid and acrylamide in a 3.2:1 w/w ratio. The study on biodegradability of the developed hydrogel showed that the hydrogel is degradable in the presence of diastase (amylase). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1650–1658, 2003     

Preparation and Characterization of Poly(N‐Vinylpyrrolidone‐co‐Methacrylic Acid) Hydrogels

In this study, N‐vinylpyrrolidone (VP)/methacrylic acid (MAA) copolymers have been prepared at three different mole percents, the methacrylic acid composition being around 5, 10, 15%. MAA and VP monomer mixtures have been irradiated in ⁶⁰Co‐γ source at different irradiation doses and percent conversions have been determined gravimetrically. ～80% conversion of monomers into hydrogels were performed at 3.4 kGy irradiation dose. These hydrogels were swollen in distilled water at pH 4.0, 7.0, and 9.0. P(VP/MAA) hydrogel which contains 5% methacrylic acid showed the maximum % swelling at pH 9.0 in water. Diffusion of water was found to be of non‐Fickian character. Diffusion coefficients of water in P(VP/MAA) hydrogels were calculated. Initial swelling rates of P(VP/MAA) hydrogels increased with increasing pH and MAA content in hydrogels. Swelling kinetics of P(VP/MAA) hydrogels was found to be of second order. Thermal behavior of PMAA, PVP and P(VP/MAA) hydrogel were investigated by thermal analysis. P(VP/MAA) hydrogel gained new thermal properties and the temperature for maximum weight loss and temperature for half‐life of P(VP/MAA) hydrogel were determined.     

电化学诱导聚合甲基丙烯酸膜及葡萄糖酶电极制备

应用电化学还原诱导自由基聚合方法在金基底上聚合甲基丙烯酸水合凝胶膜.聚合过程为:在中性缓冲溶液中,由电还原过硫酸根离子产生的硫酸根自由基,激发甲基丙烯酸发生自由基聚合反应,形成超薄的水合凝胶膜;同时也可将葡萄糖氧化酶包敷于膜内,制成葡萄糖氧化酶电极.     

Synthesis and Evaluation of Biocompatible pH‐Sensitive Hydrogels as Colon‐Specific Drug Delivery Systems

Because of the growing importance of pH‐sensitive hydrogels as drug delivery systems, biocompatible copolymeric hydrogels based N‐vinyl‐2‐pyrrolidinone (NVP) and methacrylic acid (MAA) were designed and synthesized. These hydrogels were investigated for oral drug delivery. Radical copolymerizations of N‐vinyl‐2‐pyrrolidinone (NVP) and methacrylic acid (MAA) with the various ratios of cross‐linking agent were carried out at 70 °C. Azabisisobutyronitrile (AIBN) was the free‐radical initiator employed and Cubane‐1,4‐dicarboxylic acid (CDA) linked to two 2‐hydroxyethyl methacrylate (HEMA) group was the crosslinking agent (CA) used for hydrogel preparations. The hydrogels were characterized by differential scanning calorimetry and FT‐IR. Equilibrium swelling studies were carried out in enzyme‐free simulated gastric and intestinal fluids (SGF and SIF, respectively). A model drug, olsalazine [3,3′‐azobis (6‐hydroxy benzoic acid)] (OSZ) as an azo derivative of 5‐aminosalicylic acid (5‐ASA), was entrapped in these gels and the in‐vitro release profiles were established separately in both enzyme‐free SGF and SIF. The drug‐release profiles indicated that the amount of drug released depended on the degree of swelling. The swelling was modulated by the amount of crosslinking of the polymer bonded drug (PBDs) prepared. Based on the great difference in hydrolysis rates at pH 1 and 7.4, these pH‐sensitive hydrogels appear to be good candidates for colon‐specific drug delivery.     

Responsive thin hydrogel layers from photo-cross-linkable poly(N-isopropylacrylamide) terpolymers

The structural features and swelling properties of responsive hydrogel films based on poly(N-isopropylacrylamide) copolymers with a photo-cross-linkable benzophenone unit were investigated by surface plasmon resonance, optical waveguide mode spectroscopy, and atomic force microscopy. The temperature-dependent swelling behavior was studied with respect to the chemical composition of the hydrogel polymers containing either sodium methacrylate or methacrylic acid moieties. In the sodium methacrylate system, a refractive index gradient was found that was not present in the free acid gel. This refractive index gradient, perpendicular to the swollen hydrogel film surface, could be analyzed in detail by application of the reversed Wentzel-Kramers-Brillouin (WKB) approximation to the optical data. This novel approach to analyzing thin-film gradients with the WKB method presents a powerful tool for the characterization of inhomogeneous hydrogels, which would otherwise be very difficult to capture experimentally. In AFM images of the hydrogel layers, a macroscopic pore structure was observed that depended on the polymer composition as well as on the swelling history. This pore structure apparently prevents the often-observed skin barrier effect and leads to a quickly responding hydrogel.     

Effect of Different Composition on Particle Size Chitosan-PMAA-PNIPAM Hydrogel

Chitosan-based (chitosan-poly(methacrylic acid)-poly(N-isopropylacrylamide) [Cs-PMAA-PNIPAM] copolymer hydrogels were synthesized by free radical emulsion polymerization to study the effect of different composition of monomer on hydrogel particle size. Chitosan usually applied for medical use such as drug delivery due to its biodegradability, bio-compatibility, and non-toxicity properties. Co-polymerized chitosan with MAA and NIPAM is an improvement of chitosan gel to be more responsive to the environment of human body included different pH, temperature, ionic strength, electric field, and enzyme activities. Small size of the particles is particularly important to ensure the particles reach the target site especially as a drug delivery. A full factorial experimental design (2³) was employed to identify which factors influenced most on the particle size. The design considered three factors which is amount of MAA, NIPAM and N,N’-Methylenebisacrylamide (MBA) while particle size are chosen as the responses of the variation on each composition. Particle size distribution was measured by laser diffractionin wet condition. From the design of experiment, NIPAM shows the main factor affected the particle size. However combination of the others factors also contributed on the whole size of the hydrogel.     

Penetration of3H-glycerol trinitrate through silicone-hydroxyethyl methacrylate matrices

The possibility of use of a powder-like polymeric hydrogel of 2-hydroxyethyl methacrylate with 33 wt.% methacrylic acid as potential pharmaceutical adjuvant in the form of a composite powdered material, with silicone rubber in the form of matrices for transdermal therapeutic system has been studied. The effect of solvents and the content of composite hydrogel in matrices on the rate of permeation of an antianginic drug, radioactive labeled glycerol trinitrate (GTN) was evaluated. The results show that hydrogel copolymers are prospective adjuvants for transdermal therapeutic systems.     

红霉素分子印迹二维光子晶体水凝胶传感器的研究

以红霉素为印迹分子,聚苯乙烯二维光子晶体为模板,甲基丙烯酸为功能单体,乙二醇二甲基丙烯酸甲酯为交联剂,2,2-二乙氧基苯乙酮为引发剂,紫外光引发聚合,在甲醇-乙酸(9∶1, V/V)中洗脱印迹分子,得到能够特异性识别红霉素的分子印迹二维光子晶体水凝胶.通过测试德拜环直径变化,研究了此水凝胶在红霉素溶液中的响应性能.实验结果表明,当红霉素的浓度从0增加到1×10-6 mol/L时,德拜环直径增加6 mm, 相应的晶格间距减小30 nm.此外,水凝胶在1×10-6 mol/L红霉素的类似物罗红霉素、琥乙红霉素溶液中,德拜环直径仅分别增加1.5和2.0 mm,表明此光子晶体水凝胶具有良好的选择性,有望用于红霉素低成本的简易检测.     

Preparation of monodisperse,reactive hydrogel microspheres and their amphoterization

Monodisperse, reactive hydrogel microspheres were prepared by precipitation polymerization ofp-nitrophenyl acrylate (NPA) with acrylamide, methacrylic acid, and methylenebisacrylamide in ethanol. The size of microspheres was controlled by the monomer ratio. Some fraction of reactive ester decomposed during the polymerization. The reactive hydrogel microspheres were converted to amphoteric ones by the reaction of NPA units with diamine. The isoelectric point of the amphoteric microspheres was around 4.0, but it was different from the pH at which the microspheres have the minimum size or the most shrunken state. This was attributed to the uneven distribution of induced amine groups.