原位交联杂化型聚合物电解质膜的形成机理、结构模型及其电化学性能

合成含有Ti(Ⅵ)杂化中心的交联(柠檬酸钛络合体-聚乙二醇)聚酯网络作为基体,水解生成的Nano-TiO₂粒子为填料,LiI/I₂为导电离子,通过原位聚合复合法制备了Nano-TiO₂/(柠檬酸钛络合体-聚乙二醇)/LiI/I₂交联杂化型聚合物电解质膜。采用局域密度近似(LDA)法、Raman光谱、傅里叶变换红外光谱(FTIR)、透射电子显微镜(TEM)和能量散射X射线分析(EDXA)探讨了交联杂化聚合物基体的形成机理,并建立了其相应的结构模型。在此基础之上,研究了四异丙氧基钛(Ti(iOPr)₄)的含量对Nano-TiO₂/(柠檬酸钛络合体-聚乙二醇)/LiI/I₂电解质膜的结构及电化学性能的影响。研究表明:当Ti(iOPr)₄含量高于12 % (w)时,Nano-TiO₂粒子和Ti(Ⅵ)杂化中心的共同作用不仅有效提高了电解质膜的离子电导率(σ),而且显著改善了电解质膜与电极间的界面稳定性;Ti(iOPr)₄含量为48 % (w)时,电解质膜的室温离子电导率达到最大值9.72×10^-5 S·cm^-1,电解质膜的界面电阻于6d后趋于稳定。     

P(VdF-HFP)-基离子液体复合聚合物电解质的阴极稳定性及热稳定性

以聚偏氟乙烯-六氟丙烯P(VdF-HFP)聚合物为基体, 制备了含离子液体1-甲基-3-乙基咪唑六氟磷酸盐(EMIPF6)、用于锂离子电池的离子液体复合聚合物电解质[P(VdF-HFP)/LiPF₆/EMIPF₆/EC(碳酸乙烯酯)-PC(碳酸丙烯酯)]. 采用热重分析法以及燃烧实验测试了复合聚合物电解质的热稳定性. 离子电导率测试表明, 离子液体的存在显著改善了复合聚合物电解质的离子传输; 循环伏安测试表明, 添加剂EC和PC的加入提高了复合电解质的阴极稳定性, 制得的离子液体复合聚合物电解质在0.3-4.3 V 电压范围内稳定存在. Li₄Ti₅O₁₂ 和LiCoO₂为电极材料、P(VdF-HFP)/LiPF₆/EMIPF₆/EC-PC 为电解质的半电池表现出优良的循环性能, 0.1C充放电倍率下, Li/LiCoO₂和Li/Li₄Ti₅O₁₂半电池的可逆容量分别为130和144 mAh·g^-1. 但EC、PC在一定程度上降低了离子液体复合聚合物电解质的热稳定性.     

一种新型物理交联型凝胶聚合物电解质的制备与表征

以甲氧基聚乙二醇甲基丙烯酸酯(MPEGM)和十六烷基聚乙二醇甲基丙烯酸酯(HPEGM)为单体, 三乙二醇二甲醚(TEGDME)为增塑剂, 与锂盐(高氯酸锂, LiClO₄)和光引发剂(安息香二甲醚, DMPA)复合制成光敏体系, 经紫外(UV)固化得到物理交联型凝胶聚合物电解质(GPE)薄膜. 用红外(IR)光谱、差热分析(DSC)、拉伸测试和交流阻抗(AC) 等方法对聚合物基体和电解质的性能进行了研究.结果表明: 当共聚物P(MPEGM-co-HPEGM)中HPEGM含量为50%(w)时, 十六烷基链段(C₁₆)在聚氧化乙烯(PEO)链段静电斥力的作用下发生聚集, 自组装形成了物理交联, 提高了共聚物的空间稳定性; 温度和电解质中各组分的含量对电导率均有较大的影响, 综合性能较好的电解质在30℃时电导率可达0.87×10^-3 S·cm^-1; 采用循环伏安法测得该电解质的电化学窗口为0~4.5 V (vs. Li/Li⁺), 可以满足锂离子电池的应用要求; 组装成的LiFePO₄/GPE/Li电池, 在30℃下以0.1 C和0.2 C倍率进行充放电测试, 首次放电容量分别为154.7和148.0 mAh·g^-1.     

添加剂对离子液体凝胶聚合物电解质电化学性能的影响

本文采用1-乙基-3-甲基咪唑六氟磷酸盐(EMIPF₆)、六氟磷酸锂(LiPF₆)和偏氟乙烯-六氟丙烯共聚物(P(VdF-HFP))为原料制得P(VdF-HFP)-EMIPF₆-LiPF₆体系离子液体凝胶聚合物电解质,选取碳酸甲乙酯(EMC)、碳酸二甲酯(DMC)、碳酸二乙酯(DEC)以及碳酸乙烯酯(EC)和碳酸丙烯酯(PC)混合物(EC-PC)作为离子液体凝胶聚合物电解质的添加剂,分别研究了它们对聚合物电解质膜电化学性能的影响。结果表明：加入EC-PC的P(VdF-HFP)-EMIPF₆-LiPF₆电解质膜的电化学窗口达到4.6 V,锂离子迁移数为0.44,30 ℃时离子电导率为1.65 mS·cm^-1;而DEC、DMC、EMC对电解质膜的电化学稳定性、锂离子迁移数存在不良的影响,对离子电导率的提高不明显。研究了正极材料LiCoO₂在P(VdF-HFP)-EMIPF₆-LiPF₆+EC-PC电解质中的充放电循环性能,其首次放电比容量达到116.5 mAh·g^-1,充放电20次后,电池容量没有明显衰减。     

闭式十氢十硼酸盐的制备及其固体电解质应用研究进展

全固态电池是一种具有前景的电化学储能装置,它可以克服传统有机液体电解质电池的多方面不足,包括电解质易泄漏、稳定性低、易燃和能量密度有限等问题。固态电解质是全固态电池的重要组成部分,开发具有高离子电导率和宽电化学稳定性窗口的固体电解质是研制高能量和高功率密度全固态电池的关键问题之一。硼氢化物基固态电解质作为一类新型电解质,因具有高离子电导率、高热稳定性和低密度等优势而受到了广泛关注。其中,闭式十氢十硼酸碱金属盐是代表性材料之一。自1959年B₁₀H₁₀^2-被发现以来,其合成方法、结构与应用开发都得到了广泛研究。近年来其在固态电解质方面的研究证实,M₂B₁₀H₁₀（M=Na、Li等）及其衍生物具有高离子电导率、高热稳定性和化学稳定性、高电位窗口等特性,是一类颇具前景的固态电解质材料。本文主要综述了B₁₀H₁₀^2-合成方法及其在固态电解质方面的应用研究进展,并对今后B₁₀H₁₀^2-作为固态电解质的发展方向提出了展望。     

PEO-LiClO4-ZSM5复合聚合物电解质 I. 电化学研究

首次以“择形”分子筛ZSM5为填料, 通过溶液浇铸法制得PEO-LiClO₄-ZSM5全固态复合聚合物电解质(CPE)膜. 交流阻抗实验表明ZSM5的引入可以显著地提高CPE的离子电导率. 利用交流阻抗-稳态电流相结合的方法对CPE的锂离子迁移数进行了测定, 结果表明掺入ZSM5后锂离子迁移数明显升高. ZSM5的含量为10%时, CPE同时具有最高离子电导率1.4×10^－5 S•cm^－1(25 ℃)和最大锂离子迁移数0.353. PEO-LiClO₄-ZSM5/Li电极界面稳定性实验表明PEO-LiClO₄-ZSM5复合聚合物电解质在全固态锂离子电池领域具有良好的应用前景.     

PEO-LiClO4-ZSM5复合聚合物电解质 I. 电化学研究

首次以“择形”分子筛ZSM5为填料, 通过溶液浇铸法制得PEO-LiClO₄-ZSM5全固态复合聚合物电解质(CPE)膜. 交流阻抗实验表明ZSM5的引入可以显著地提高CPE的离子电导率. 利用交流阻抗-稳态电流相结合的方法对CPE的锂离子迁移数进行了测定, 结果表明掺入ZSM5后锂离子迁移数明显升高. ZSM5的含量为10%时, CPE同时具有最高离子电导率1.4×10^－5 S•cm^－1(25 ℃)和最大锂离子迁移数0.353. PEO-LiClO₄-ZSM5/Li电极界面稳定性实验表明PEO-LiClO₄-ZSM5复合聚合物电解质在全固态锂离子电池领域具有良好的应用前景.     

Li7P3S11电解质的合成、传导及应用

固态电解质是固态电池中的关键材料,开发具有高离子电导率、高化学/电化学稳定性、电极兼容性良好的固态电解质正成为研究热点。硫化物固态电解质相较其它固态电解质具有更高的离子电导率和良好的机械加工性能等优势,是最有前景实现实用化的固态电解质之一。在众多硫化物固态电解质中,Li₇P₃S₁₁因其高的离子电导率和较低的原料成本而极具研究意义。本文首先介绍了Li₇P₃S₁₁电解质的结构、Li⁺传导机理及合成路径;其次,针对该电解质的电导率提高、空气/水稳定性提升、固固界面稳定性及电解质自身稳定性改善等问题,综述了目前常用的改性策略研究;再次,总结了基于Li₇P₃S₁₁电解质的全固态锂离子电池和全固态锂硫电池的构筑;最后,本文分析了Li₇P₃S₁₁电解质的研究和应用面临的挑战,并指出该电解质未来发展的趋势。     

锂离子电池PMMA-VAc聚合物电解质的制备与性质研究

以甲基丙烯酸甲酯(MMA)和醋酸乙烯酯(VAc)为单体, 用乳液聚合法合成聚甲基丙烯酸甲酯-醋酸乙烯酯聚合物(PMMA-VAc), 并以此聚合物制备了新型聚烯烃膜支撑的聚合物膜及聚合物电解质. 用红外光谱(FTIR)、凝胶色谱(GPC)、差热和热重分析(DSC/TG)、扫描电镜(SEM)及电池充放电实验等方法研究了聚合物、聚合物膜和聚合物电解质的性质. 红外光谱结果表明, MMA与VAc通过各自的C＝C双键打开聚合成PMMA-VAc. PMMA-VAc易于分散在混合碳酸酯溶剂中并形成凝胶, 凝胶粘度随PMMA-VAc浓度的增加而增加, 当浓度为4%时成膜效果最佳. PMMA-VAc膜具有大量的微孔结构, 具有极强的吸液性能. PMMA-VAc膜具有良好的热稳定性: 在380 ℃范围内保持稳定. 聚烯烃膜支撑的PMMA-VAc膜室温下的离子电导率为1.85×10^－3 S•cm^－1, 用作为锂离子电池的聚合物电解质时, 电池具有良好的循环稳定性和倍率性能.     

尿素作为造孔剂对聚乙烯支撑的PAMS聚合物电解质性能的改进

采用乳液聚合法合成聚(丙烯腈-甲基丙烯酸甲酯-苯乙烯) (P(AN-MMA-ST)或者共聚物PAMS), 并利用尿素作为造孔剂制备了聚乙烯(PE)支撑的PAMS聚合物膜(PE-PAMS-U)及凝胶聚合物电解质(GPE). 利用傅里叶变换红外(FTIR)光谱、X射线衍射(XRD)、扫描电子显微镜(SEM)、热重(TG)分析、线性电位扫描(LSV)、电化学阻抗谱(EIS)以及充放电等方法对PAMS聚合物以及PE支撑的聚(丙烯腈-甲基丙烯酸甲酯-苯乙烯) (PE-PAMS)聚合物隔膜及凝胶聚合物电解质的性能进行了研究. 结果表明, 利用尿素作为造孔剂可以提高PE-PAMS凝胶聚合物的性能. 由于尿素的加入, 聚合物膜呈现均匀的微孔结构, 室温下的电导率从1.1×10^-3 S·cm^-1提高到2.15×10^-3 S·cm^-1. 同时, 锂电极/聚合物电解质界面上的电荷传递电阻也从480 Ω·cm²降低到 250 Ω·cm². 电化学稳定窗口为5.0 V. 电池(Li/PE支撑的GPE/LiCoO₂)的测试证明, 用尿素作为造孔剂的凝胶聚合物锂离子电池表现出优良的倍率性能和循环性能.     

The effects of polymer gel electrolyte composition on performance of quasi-solid-state dye-sensitized solar cells

Polymer gel electrolytes based on poly(acrylic acid)-poly(ethylene glycol) (PAA–PEG) hybrid have been prepared and applied to developed quasi-solid-state dye-sensitized solar cells (DSCs). PAA–PEG hybrid was synthesized by polymerization reaction. Quasi-solid-state DSCs were fabricated with synthesized PAA–PEG electrolyte. The effects of alkali iodides LiI, KI, and I₂ concentrations on liquid electrolyte absorbency and ionic conductivity of PAA–PEG were investigated. The evolution of the solar cell parameters with polymer gel electrolyte compositions was revealed. DSCs based on PAA–PEG with optimized KI/I₂ concentrations showed better performances than those with optimized LiI/I₂ concentrations. The electrochemical impedance spectroscopy technique was employed to examine the electron lifetime in the TiO₂ electrode and quantify charge transfer resistances at the TiO₂/dye/electrolyte interface and the counter electrode in the solar cells based on the PAA–PEG hybrid gels. A maximum conversion efficiency of 4.96% was obtained for DSCs using KI based quasi-solid electrolyte under 100 mW cm⁻². Our work suggests that KI can be the promising alkali metal iodide for improving the performance of PAA–PEG hybrid gel DSCs.     

Effect of single-wall carbon nanotubes on the properties of polymeric gel electrolyte dye-sensitized solar cells

A hybrid of polymer/dispersed single-wall carbon nanotubes was utilized in networking a novel composition of gel electrolyte in dye-sensitized solar cells. The gel is composed of polyethylene glycol, polyvinyl pyrrolidone, single-wall carbon nanotubes, and I^?/I₃ ^? as electrolyte. Formation of the less conductive polyiodide species in electrolyte was prohibited by the addition of single-wall carbon nanotubes leading to the excellent photovoltaic behavior of the cell under simulated standard illumination of the fabricated device owing to the increased open circuit voltage (0.47 V). Electrochemical impedance spectroscopy was employed to quantify the charge transport resistance and the electron lifetime at the TiO₂ conduction band. Charge transport resistances at the TiO₂/dye/electrolyte interface were determined for the cells consisting of the non-gel reference and our new gel electrolytes, and it was indicated that the charge recombination between injected electrons and electron acceptors (I₃ ^?) in the redox electrolyte was remarkably retarded. Electrochemical parameters obtained by the fitting showed all of the resistances increased as compared to liquid electrolyte dye-sensitized solar cells that can be related to the increase in viscosity of the gel, which hinders the ionic transportation through the electrolyte. These results were also confirmed by the electron lifetime analyses. The characteristic peak shifted to a lower frequency in the Bode phase plot for the cell containing gel electrolyte which is an indication of a longer electron lifetime in comparison with that of the cell containing very conventional liquid electrolyte.     

Compositional effect on the morphology and ionic conductivity of thermoplastic polyurethane based electrolytes

Four thermoplastic polyurethanes (TPUs) were synthesized from poly(ethylene glycol) (PEG), 4,4^′-methylenebis(phenyl isocyanate) (MDI), and 1,4-butanediol (1,4-BDO) with different 1,4-BDO/PEG ratios. The effect of polymer structure on the conductivity of the polymer elelctrolytes was investigated. Fourier transform infrared spectroscopy (FT-ir) and differential scanning calorimetry (DSC) were utilized to monitor changes in the morphology of the TPUs as polymeric solid electrolyte doped with LiClO₄. The structure of the TPUs has been investigated by 1H solution nuclear magnetic resonance spectroscopy. Alternating current (AC) impedance experiments were performed to determine the ionic conductivities of TPU films and their corresponding gel type electrolytes. The conductivity depends on the soft-segment concentration and on the degree of phase separation exhibited by these materials. One of the investigated TPU gel type electrolytes exhibits an ionic conductivity as high as 3×10⁻⁴ S/cm at room temperature.     

Solid polymer electrolytes III: Preparation,characterization, and ionic conductivity of new gelled polymer electrolytes based on segmented,perfluoropolyether‐modified polyurethane

New segmented polyurethanes with perfluoropolyether (PFPE) and poly(ethylene oxide) blocks were synthesized from a fluorinated macrodiol mixed with poly(ethylene glycol) (PEG) in different ratios as a soft segment, 2,4‐toluene diisocyanate as a hard segment, and ethylene glycol as a chain extender. Fourier transform infrared, NMR, and thermal analysis [differential scanning calorimetry and thermogravimetric analysis (TGA)] were used to characterize the structures of these copolymers. The copolymer films were immersed in a liquid electrolyte (1 M LiClO₄/propylene carbonate) to form gel‐type electrolytes. The ionic conductivities of these polymer electrolytes were investigated through changes in the copolymer composition and content of the liquid electrolyte. The relative molar ratio of PFPE and PEG in the copolymer played an important role in the conductivity and the capacity to retain the liquid electrolyte solution. The copolymer with a 50/50 PFPE/PEG ratio, having the lowest decomposition temperature shown by TGA, exhibited the highest ionic conductivity and lowest activation energy for ion transportation. The conductivities of these systems were about 10^?3 S cm^?1 at room temperature and 10^?2 S cm^?1 at 70 °C; the films immersed in the liquid electrolyte with an increase of 70 wt % were homogenous with good mechanical properties. © 2002 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 486–495, 2002; DOI 10.1002/pola.10119     

Properties of a nanocomposite polymer electrolyte from an amorphous comb-branch polymer and nanoparticles

Three fully amorphous comb-branch polymers based on poly(styrene-co-maleic anhydride) as a backbone and poly(ethylene glycol) methyl ether of different molecular weights as side chains were synthesized. SiO₂ nanoparticles of various contents and the salt LiCF₃SO₃ were added to these comb-branch polymers to obtain nanocomposite polymer electrolytes. The thermal and transport properties of the samples have been characterized. The maximum conductivity of 2.8×10^–4 S cm^–1 is obtained at 28 °C. In the system the longer side chain of the comb-branch polymer electrolyte increases in ionic conductivity after the addition of nanoparticles. To account for the role of the ceramic fillers in the nanocomposite polymer electrolyte, a model based on a fully amorphous comb-branch polymer matrix in enhancing transport properties of Li⁺ ions is proposed.     

In situ formation of polyethylene glycol–titanium complexes as solvent-free electrolytes for electrochromic device application

Transparent and ionic conductive polymeric electrolytes have been prepared through sol–gel method by adding titanium isopropoxide into an acidic polyethylene glycol (PEG) solution. After hydrolysis and condensation processes, new associations between titanium cations and ether oxygen atoms of PEG have been formed according to Fourier-transform infrared spectroscopy. Thermogravimetric analysis results of these hybrid materials indicate a better thermal stability with a less polydispersion of the molecular mass distribution in comparison with PEG. For the purpose of electrochromic or photoelectrochromic device applications, LiI was added into the hybrid materials to form solvent-free polymeric electrolytes. Optical transmittance spectra of these electrolytes show a red shift of the cutoff wavelength as a function of titanium isopropoxide percentage in the original sol–gel solutions. It is also observed that the amount of hydroxyl groups in the hybrid materials was reduced in comparison with the PEG one. This makes electrical conductivity of the hybrid electrolytes with LiI salt insensitive to humidity and solvents, which was about 2 × 10^-4 Ω⁻¹ cm⁻¹ at room temperature. A solid WO₃-based electrochromic device with the hybrid electrolyte keeps the same optical transmittance value after 1,000 cycles of switching polarization potentials between −1 and +1 V.     

New solid polymer electrolytes based on polyester diacrylate for lithium power sources

New solid polymer electrolytes are developed for a lithium power source used at the temperatures up to 100°C. Polyester diacrylate (PEDA) based on oligohydroxyethylacrylate and its block copolymers with polyethylene glycol were offered for polymer matrix formation. The salt used was LiClO₄. The ionic conductivity of electrolytes was measured in the range of 20 to 100°C using the electrochemical impedance method. It is shown that the maximum conductivity in the whole temperature range is characteristic of the electrolyte based on the PEDA copolymer and polyethylene glycol condensation product (2.8 × 10^?6 S cm^?1 at 20°C, 1.8 × 10^?4 S cm^?1 at 95°C).     

A novel composite polymer electrolyte containing room-temperature ionic liquids and heteropolyacids for dye-sensitized solar cells

A novel composite polymeric gel comprising room-temperature ionic liquids (1-butyl-3-methyl-imidazolium-hexafluorophosphate, BMImPF₆) and heteropolyacids (phosphotungstic acid, PWA) in poly(2-hydroxyethyl methacrylate) matrix was successfully prepared and employed as a quasi-solid state electrolyte in dye-sensitized solar cells (DSSCs). These composite polymer electrolytes offered specific benefits over the ionic liquids and heteropolyacids, which effectively enhanced the ionic conductivity of the composite polymer electrolyte. Unsealed devices employing the composite polymer electrolyte with the 3% content of PWA achieved the solar to electrical energy conversion efficiency of 1.68% under irradiation of 50 mW cm⁻² light intensity, increasing by a factor of more than three compared to a DSSC with the blank BMImPF₆-based polymer electrolyte without PWA. It is expected that these composite polymer electrolytes are an attractive alternative to previously reported hole transporting materials for the fabrication of the long-term stable quasi-solid state or solid state DSSCs.     

Single-ionic gel polymer electrolyte based on polyvinylidene fluoride and fluorine-containing ionomer

The novel single-ionic conductive gel polymer electrolyte was prepared from polyvinylidene fluoride (PVDF), propylene glycol carbonate (PC) and a new fluorine-containing ionomer. Cation-carbonyl interaction behavior, morphology and ionic conductive properties of this gel polymer electrolyte were studied by infrared spectra analysis (IR), nuclear magnetic resonance (NMR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and complex impedance analysis. The results showed that the fluorine-containing ionomer was miscible with both PVDF and PC, and that the carbonyl groups in the ionomer and PC could bond competitively with the cation. Both the content of fluorine-containing ionomer and the content of PC had a great effect on morphology and ionic conductive properties of the samples. For this new gel polymer electrolyte, an ionic conductivity of above 10⁻⁴ S cm⁻¹ at room temperature could be reached, and this electrolyte system was a single-ionic kind gel polymer electrolyte with the transport number of the sodium ion exceed 0.99 (t₊>0.99).