全二维气相色谱-飞行时间质谱分析焦化柴油中饱和烃的分子组成

建立了全二维气相色谱-飞行时间质谱(GC×GC-TOF MS)分析柴油馏分中饱和烃的分子组成的方法。结合谱库检索、质谱图解析、沸点与分子结构关系和全二维谱图特征,定性(或归类)了焦化柴油饱和烃组分中1057个化合物单体,其中正构烷烃排列规律性最强,一环~三环环烷烃按照极性和沸点的差异呈瓦片状分布在其上方。另外,还准确区分了在一维气相色谱上共流出的正构烷基环己烷和正构烷基环戊烷,以及正构 α 单烯烃。根据质谱采集的总离子流色谱图,采用峰面积归一化法得到了饱和烃组分的碳数分布结果,并将该方法应用于研究不同类型柴油馏分饱和烃的分子组成特点。结果表明,催化裂化和焦化柴油馏分饱和烃组分的化合物类型和分布各不相同。分子组成分析能为油品加工工艺机理的研究提供方法支持。     

原油饱和烃指纹的内标法分析

采用内标法建立了原油中正构烷烃、生物标志物(甾、萜烷类)的分析方法。确定了样品前处理方法和组分定性定量方法。讨论了柱层析分离能力。结果表明,所有饱和烃组分均流入第一部分流出液F1中,分离能力较为满意。对48种甾、萜烷类生物标志物组分以及姥鲛烷、植烷和正构烷烃等进行了定性确认,定性化合物数量多,信息量大,易于据此进行可靠的油指纹分析鉴别。32个正构烷烃组分相对标准差为1.2%～7.4%;45个生物标志物组分相对标准偏差为2.5%～9.2%。分析精密度较好,满足油指纹鉴别需要。正构烷烃回收率为73%～116%;生物标志物为84%～106%;回收率结果较为满意。正构烷烃方法检出限为7.0μg/g;生物标志物为0.65μg/g,满足原油样品分析要求。通过本方法对自不同和相同平台的原油样品进行饱和烃浓度分析,并采用浓度数据进行鉴别,结果与实际情况相符。     

几种烟煤CS2萃取物的GC/MS分析

利用气相色谱－质谱联用（GC／MS）技术测定了平朔、大同和神府三种烟煤中CS2萃取物的成分，对其化学组成及结构特征进行了对比研究。结果表明，萃取物主要由脂肪烃、芳烃和含杂原子化合物三类成分组成。芳烃在萃取物整体中占绝对优势，以苯系、萘系、菲系和芘系的烷基取代芳烃为主要成分：脂肪烃除主要成份正构烷烃外，还有少量的类异戊二烯烃和萜烷；含杂原子化合物所占的比例很小，以含氧、氮和硫的化合物为主，在平朔和大同煤的CS2萃取还发现少量邻二氯苯。     

全二维气相色谱-飞行时间质谱/氢火焰离子化检测器对煤直接液化循环溶剂的定性与定量分析

建立了全二维气相色谱-飞行时间质谱/氢火焰离子化检测器(GC×GC-TOF MS/FID)对煤直接液化循环溶剂(CDLRS)定性定量的分析方法。采用TOF MS和FID两种检测器同时采集数据,并结合谱库检索、标准物质保留值对照、谱图解析、标准质谱图对照、全二维谱图特征以及提取化合物分子离子等定性方法,将TOF MS检测数据定性,然后将定性的烃类化合物以z值分类法分为18类;应用Chroma TOF数据处理软件将TOF MS数据的定性分类结果应用到FID的检测数据中,对TOF MS和FID采集的数据色谱峰面积归一化处理,实现CDLRS的半定量分析。GC×GC/FID定量结果显示:煤直接液化循环溶剂中饱和烃和芳烃分别占45.805%、53.938%,其中饱和烃主要为二环烷烃及三环烷烃,含量依次为14.644%、18.021%;芳烃主要为一环烷苯和二环烷苯,含量依次为19.759%、16.528%。该方法为CDLRS的定性定量提供了一种有效的分析方法。     

无分流进样和交联、键合毛细管柱在石油饱和烃色谱分析中的应用

生油岩和石油中萃取分离出的饱和烃馏分,主要由碳数范围C_(11)～C_(50)正构烷烃、异构烷烃及环烷烃组成,饱和烃的气相色谱分析结果可以得出碳数分布、主峰碳、成熟度等一系列重要地球化学指标数据,是目前国内外应用最多最广的石油地球化学分析项目之一。     

红外吸收光谱法分析饱和烃的结构族组成

根据30多个纯饱和烃的红外光谱数据以及文献数据,并将短阵运算用于最小二乘法,求出了测定饱和烃中CH_3,CH_2,和结构族组成的多重迴归方程式.可用来分析石油馏分饱和烃的结构族组成.经用单体烃和配制的饱和烃混合物校验,求得平均分析误差如下:CH_3<±4%,开链CH_2<±5%,及。讨论了饱和烃支链甲基在1340—1400厘米~(-1)区吸收的反常现象,计算出支链甲基吸收为尾端甲基的2.8倍.在计算光谱狭缝宽度/谱带表观半宽度≯0.2的情况下,所得吸收率与Jones的正烷烃在3000厘米~(-1)处的数据相吻合,作者认为此条件可能成为统一各实验室测定液态烷烃红外光谱数据的标准.     

海洋石油降解细菌对石油烃降解效果的气相色谱法分析

用毛细管气相色谱法分析评价海洋石油降解细菌对石油烃的降解效果,结果表明,毛细管气相色谱法能够测定出石油降解细菌对石油烃的降解进程和对正构烷烃的总降解率,以及温度对降解速率的影响。石油降解细菌对正构烷烃有明显的降解作用,混合菌株的降解率明显高于单菌株的降解率;在20℃的条件下,经过21 d后,绝大部分的正烷烃被降解,总的降解率为94.93%。     

褐煤超临界流体抽提产物中脂肪烃组成结构的特征

用硅胶-氧化铝柱色谱预分离和色谱-质谱分析研究了两种褐煤超临界流体抽提物中脂肪烃馏分组成结构特征。结果表明,除主要成份正构烷烃(C_(13)～C_(33))外,尚有少量的类异戊二烯烃(姥鲛烷、植烷等)和萜烷。其中萜烷以五环三萜为主(C_(27)、C_(29)～C_(32)藿烷类化合物),并有一定量的C_(27)、C_(29)和C_(30)藿烯,倍半萜和三环二萜烷含量很少。未检出甾烷。此外,还检出一完整系列的烯烃。试验结果表明,超临界流体抽提条件对褐煤抽出物各组分、含量及其分布有一定的影响。     

烷基苯生产中循环烷烃的液固吸附色谱预分离和气相色谱/质谱分析

 利用 10 0目～ 2 0 0目的硅胶 ,选择正戊烷和二氯甲烷作为洗脱剂 ,采用吸附色谱法将烷基苯生产中的循环烷烃分离为饱和烃 (烷烃 +环烷烃 )及芳烃两部分。然后将饱和烃及芳烃分别进行色谱 /质谱 (GC/MS)联用分析 ,得到了有关循环烷烃构成的定性定量结果。定性结果如实地反映出烷基苯生产中的副反应产物 ,可直接用于指导生产。从定量结果可以看出 ,经过硅胶吸附分离后 ,试样中含量要求很低的芳烃被浓缩 ,提高了分析的准确度和灵敏度 ,可以检测出循环烷烃中含量很低的物质 ,为全面分析样品组成提供了有力的证据。     

饱和烃热裂化夺氢氢转移能力研究

研究了在热反应条件下石油渣油中饱和烃夺氢氢转移能力的测定方法和结果。饱和烃受热生成的自由基可从氢化芳烃四氢萘夺取活泼氢,由此可测定不同饱和烃的夺氢能力。研究结果表明,饱和烃可剧烈裂化而具有较强的夺氢能力,且这种夺氢能力随反应条件苛刻度增大而增强,对于正构烷烃或石蜡系列,其夺氢能力随分子量增大而增强,而对于不同来源石油渣油的饱和分,其夺氢能力的差别不大。沥青质的存在可诱导饱和烃剧烈裂化,增大饱和烃的夺氢能力。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.