单扫描示波极谱法同时检测哌拉西林钠和氯霉素

建立了一种同时测定哌拉西林钠和氯霉素的单扫描示波极谱法。在0.66 mol/L KCl(pH 7.20)底液中,氯霉素和哌拉西林钠在汞电极上均有一灵敏的导数还原峰,哌拉西林钠和氯霉素的峰电位分别为-1.230 V和-0.638 V,检出限分别为4.5×10-8和8.2×10-9mol/L,峰电流与浓度分别在9.0×10-6~7.0×10-8mol/L和4.0×10-6~4.0×10-8mol/L范围有良好线性关系,r均大于0.998。将该法应用于氯霉素滴眼液和注射用的哌拉西林钠中氯霉素及哌拉西林钠的测定。用单扫描示波极谱法和循环伏安法研究了哌拉西林钠和氯霉素的电化学行为,实验表明该体系为一具有吸附性的不可逆过程。     

硒代胱氨酸在银电极上的电化学行为及其定量分析

研究了硒代胱氨酸 (SeCys)于0.03mol/L的硼砂 -NaOH( pH9.5)介质中在银电极上的电化学行为 ;实验发现在 -0.62V和 -0.68V(vsSCE)处存在一对氧化还原峰 ,其峰电流与硒代胱氨酸浓度具有良好的线性关系 ,由此建立了SeCys的电分析化学测定方法, (1)循环伏安法 ,其线性范围为8.6×10 -9～1.1×10 -7mol/L,检出限为4.3×10 -10mol/L, (2)二次微分线性扫描伏安法 ,其线性范围为2.2×10 -10～1.0×10 -8mol/L,检出限为8.6×10-11mol/L;该法应用于中药黄芪中SeCys含量的测定 ,结果令人满意 ;该文还探讨了硒代胱氨酸在上述条件下的电极反应机理     

青霉素 V钾的二次微分简易示波伏安法测定

利用青霉素 V钾在 pH=7的 KH2PO4-Na2HPO4缓冲溶液中产生切口的示波特性 , 提出了一种药片中青霉素 V钾的测定方法 - - 二次微分简易示波伏安法 ; 校正曲线的线性范围为 2.0× 10-5～ 2.0× 10-4 mol/L, 检出限为 8× 10-6 mol/L; 对 7.0× 10-5 mol/L青霉素 V钾 8次测定结果的相对标准偏差为 1.6% ; 实验结果表明该法具有分析速度快、仪器装置简单以及药片中的淀粉等物质不干扰测定的优点 .     

锆(Ⅳ)-邻苯二酚紫络合物碳糊电极阳极吸附伏安法研究

研究了锆(Ⅳ)-邻苯二酚紫(PV)络合物在碳糊电极上的吸附伏安行为。测定锆最佳条件为:0.08mol/L的HNO3为底液,于0.4V富集50s,从0.4至1.4V以100mV/s的速率线性扫描。在0.85V(vs.SCE)的二次导数氧化峰电流与锆的浓度在3.0×10-9～5.0×10-8mol/L(5.6×10-7mol/LPV)和1.0×10-8～1.0×10-7mol/L(5.6×10-6mol/LPV)成线性关系。富集80s,检出限为1.0×10-9mol/L(S/N=3)。该法用于标准岩石样品中锆的测定,不需萃取分离和掩蔽,直接测定,结果满意。铪(Ⅳ)在同样的实验条件下也于0.85V产生一络合吸附峰,灵敏度稍低于锆。     

聚L-白氨酸修饰电极伏安法测定痕量多巴胺的研究

用循环伏安法制备了聚L-白氨酸修饰玻碳电极,研究了多巴胺在聚L-白氨酸修饰玻碳电极上的电化学行为,建立了循环伏安法测定痕量多巴胺的新方法。实验结果表明,在pH 6.0的磷酸盐缓冲溶液中,多巴胺在聚L-白氨酸修饰玻碳电极上产生一对灵敏的氧化还原峰,峰电位分别为Epa=0.281V,Epc=0.170 V(相对Ag/AgCl电极)。峰电流与多巴胺的浓度在5.0×10-8~5.0×10-4mol/L的范围内有线性关系,检出限为5.0×10-9mol/L。对1.0×10-5mol/L多巴胺溶液平行测定9次,其相对标准偏差为4.0%。已用于针剂中多巴胺的测定。     

舒乐安定吸附伏安法的研究

Jimenez曾研究了舒乐安定的性质,但灵敏度较低,本文提出了测定痕量舒乐安定的吸附伏安法,在0.1 mol/L NH_3-NH_4Cl溶液(pH 9.3)中,富集电位—0.80 V(us. Ag/AgCl)得一灵敏的舒乐安定还原峰,Ep=—1.05 V,i_p与舒乐安定浓度在3.0×10~(-9)～5.0×10~(-6) mol/L范围内呈线性关系,检测限达1.0×10~(-9)mol/L,并用于试样的测定,用循环伏安法和恒电     

镓(Ⅲ)-茜素氨羧络合剂在碳糊电极上的阳极吸附伏安法研究及应用

研究了镓(Ⅲ)-茜素氨羧络合剂(ALC)在碳糊电极上的阳极吸附伏安行为,并以此建立了一种高灵敏度、高选择性测定镓的吸附伏安法.在0.12 mol/L HAc-NaAc-0.24 mol/L邻苯二甲酸氢钾底液(pH 4.5)中,-0.10 V (vs.SCE) 富集90 s (或180 s),以250 mV/s扫速线性扫描至0.90 V, Ga3+-ALC在碳糊电极上产生灵敏的与ALC的峰电位相差近230 mV的吸附氧化峰,其二次导数峰电流与镓浓度在5.0×10-10～8.0×10-7 mol/L范围内呈线性关系;富集240 s检出限达3.0×10-10 mol/L(S/N=3).探讨了电极反应机理.该法用于粮食样品中镓的测定,结果满意.     

钴/玻碳离子注入修饰电极伏安法测定呋喃妥因的研究

呋喃妥因 (NFT)在 0 .1mol/LHAc NaAc (pH 4 .0 )溶液中于钴 /玻碳 (Co/GC)离子注入修饰电极上产生一灵敏的伏安还原峰 ,峰电位为 - 0 .2 6V(vs.Ag/AgCl) ,峰电流与NFT浓度在 6 .0× 10 -8～ 5 .0× 10 -6mol/L范围内呈线性关系 (r =0 .9987) ,检出限为 1.0× 10 -8mol/L。用线性扫描伏安法和循环伏安法研究了NFT的伏安行为、吸附特性和电极反应机理。测定了电子转移数 (n =4 )、转移系数 (α =0 .5 8)和参与反应的质子数 (X =4 )等电化学参数。结果表明该电极过程为一具有吸附性的不可逆过程。该法用于片剂中NFT含量的测定 ,得到满意的结果。用标准加入法测得该法的回收率为 94 .0 %～ 98.5 %。     

核黄素的微分脉冲溶出伏安分析

采用循环伏安法和微分脉冲溶出伏安法,对核黄素在裸金电极和巯基化合物分子自组装膜修饰金电极上的电化学行为进行了研究,发现在pH4.8的B-R缓冲溶液中,核黄素在裸金电极和分子自组装膜修饰金电极上均于-0.35V左右产生一对可逆的氧化还原峰。核黄素在裸金电极和谷胱甘肽、三巯基丙酸、二巯基苯丙咪唑分子自组装膜修饰金电极上,其浓度分别在3.0×10-7～2.3×10-4mol/L、1.05×10-6～2.0×10-4mol/L、2.1×10-6～2.08×10-4mol/L、1.05×10-6～2.0×10-4mol/L范围内与微分脉冲伏安峰峰电流之间有良好的线性关系,其相关系数分别为0.9932、0.9909、0.9857、0.9832,核黄素的检出限为2.1×10-7mol/L、5.2×10-7mol/L、8.6×10-7mol/L、5.2×10-7mol/L。对浓度为1.0×10-5mol/L的核黄素进行10次平行测定,所得峰电流的相对标准偏差为2.0%。将该方法用于核黄素片剂和复合维生素B片剂的测定,结果令人满意。     

碳糊电极阴极吸附伏安法测定橙皮甙

在0.4mol/L的NH4Cl-NH3(pH9.0)缓冲液中,使用JP-303极谱分析仪,橙皮甙在碳糊电极(CPE)上有一灵敏的吸附伏安还原峰,峰电位为-1.2V(vs.SCE).该还原峰的二阶导数峰电流与橙皮甙的浓度在2.0×10-8～1.0×10-6mol/L(富集90s)范围内成良好的线性关系,相关系数为0.9963,检出限为1.0×10-8mol/L(S/N=3,富集110s).探讨了橙皮甙在碳糊电极上的伏安性质和电极反应机理,并且成功应用于中草药桔皮中橙皮甙含量的测定.     

纺丝条件及纺丝液组成对丝素-丝胶蛋白同轴干纺纤维的影响

为了模仿家蚕的纺丝工艺及天然蚕丝的组成和皮芯结构,利用同轴干法纺丝技术制备了以再生丝素蛋白（RSF）为芯层、丝胶蛋白（SS）为皮层的RSF-SS纤维。研究了卷绕速率及芯层纺丝液中RSF质量分数对纤维形貌、2级结构及力学性能的影响。结果表明：复合纤维具有明显的皮芯结构;相对于RSF的质量分数,卷绕速率对纤维结构和性能的影...     

蜘蛛与蚕的人工强制纺丝研究进展

为制备高性能人造蜘蛛丝和蚕丝,人们在蜘蛛丝蛋白的基因重组、再生蜘蛛丝蛋白或蚕丝蛋白的仿生纺丝,以及蜘蛛与蚕的人工强制纺丝方面开展了大量工作.研究了人工强制纺丝,比较了蜘蛛牵引丝和蚕丝在不同纺丝条件下的力学性能.结果表明:在一定范围内增加纺丝速率有利于提高蜘蛛丝和蚕丝的力学性能,此外,环境温度、纺丝状态等条件对丝的性能也...     

基于动物丝蛋白的人工纺丝

动物丝，特别是蜘蛛丝近年来由于其优异的综合力学性能而备受关注。但是天然动物丝的应用由于种种原因而受到各种限制，因此人们期望通过人工纺丝获得性能与天然动物丝相近的人工丝纤维。本文就采用动物丝蛋白进行人工纺丝的历史和现状，从再生蜘蛛丝蛋白、重组蜘蛛丝蛋白和再生蚕丝蛋白等方面进行综述，比较了天然动物丝和人工丝纤维的力学性能，并且探讨了人工生物模拟纺丝制备高性能人工丝纤维（超级纤维）的前景。     

基于动物丝蛋白的人工纺丝

动物丝,特别是蜘蛛丝近年来由于其优异的综合力学性能而备受关注。但是天然动物丝的应用由于种种原因而受到各种限制,因此人们期望通过人工纺丝获得性能与天然动物丝相近的人工丝纤维。本文就采用动物丝蛋白进行人工纺丝的历史和现状,从再生蜘蛛丝蛋白、重组蜘蛛丝蛋白和再生蚕丝蛋白等方面进行综述,比较了天然动物丝和人工丝纤维的力学性能,并且探讨了人工生物模拟纺丝制备高性能人工丝纤维(超级纤维)的前景。     

Silk Fibroin/Wool Keratin Composite Scaffold with Hierarchical Fibrous and Porous Structure

The present study describes a silk microfiber reinforced meniscus scaffold (SMRMS) with hierarchical fibrous and porous structure made from silk fibroin (SF) and wool keratin (WK) using electrospinning and freeze-drying technology. This study focuses on the morphology, secondary structure, mechanical properties, and water absorption properties of the scaffold. The cytotoxicity and biocompatibility of SMRMS are assessed in vivo and in vitro. The scaffold shows hierarchical fibrous and porous structure, hierarchical pore size distribution (ranges from 50 to 650 µm), robust mechanical properties (compression strength can reach at 2.8 MPa), and stable biodegradability. A positive growth condition revealed by in vitro cytotoxicity testing indicates that the scaffold is not hazardous to cells. In vivo assessments of biocompatibility reveal that only a mild inflammatory reaction is present in implanted rat tissue. Meniscal scaffold made of SF/WK composite shows a potential application prospect in the meniscal repair engineering field with its development.     

Mulberry Leaves (Morus Rubra)-Derived Blue-Emissive Carbon Dots Fed to Silkworms to Produce Augmented Silk Applicable for the Ratiometric Detection of Dopamine

Silk fibers (SF) reeled from silkworms are constituted by natural proteins, and their characteristic structural features render them applicable as materials for textiles and packaging. Modification of SF with functional materials can facilitate their applications in additional areas. In this work, the preparation of functional SF embedded with carbon dots (CD) is reported through the direct feeding of a CD-modified diet to silkworms. Fluorescent and mechanically robust SF are obtained from silkworms (Bombyx mori) that are fed on CDs synthesized from the Morus rubra variant of mulberry leaves (MB-CDs). MB-CDs are introduced to silkworms from the third instar by spraying them on the silkworm feed, the mulberry leaves. MB-CDs are synthesized hydrothermally without adding surface passivating agents and are observed to have a quantum yield of 22%. With sizes of ≈4 nm, MB-CDs exhibited blue fluorescence, and they can be used as efficient fluorophores to detect Dopamine (DA) up to the limit of 4.39 nM. The nanostructures and physical characteristics of SF weren't altered when the SF are infused with MB-CDs. Also, a novel DA sensing application based on fluorescence with the MB-CD incorporated SF is demonstrated.     

Thermal characterization of social vespid silk

In this paper we try to establish a link between the microclimate in the wasp nest and the structure and thermal stability of vespid silk. We suggest that there are at least two types of water that is absorbed by the silk of Oriental hornets, namely, surface water and intrinsic structural water. The release of both types of water was found to be reversible. The enthalpy values of the endothermic peaks associated with the release of water from different silk samples do not differ substantially and are in the range of 106 to 130 J g^-1 for the Vespa orientalis male larvae silk (sample #1), Paravespula germanica (yellowjacket) worker larvae silk (#3) and Vespa orientalis nest envelope(#4). For the Vespa orientalis worker larvae silk (sample #2), however, it is twice as large (228 J g^-1). This is in agreement with the increased total amount of absorbed water. The silk studied has a fibrilar structure with interconnecting surfaces overlying entire regions. It is assumed that the initial water loss stems from water evaporation from the coat of the fibers - a daily occurrence in the hornets' nest. Heating to above 70°C may result in structural changes in the silk core. This revised version was published online in July 2006 with corrections to the Cover Date.     

Correlation between processing conditions,microstructure and mechanical behavior in regenerated silkworm silk fibers

Regenerated silkworm fibers spun through a wet‐spinning process followed by an immersion postspinning drawing step show a work to fracture comparable with that of natural silkworm silk fibers in a wide range of spinning conditions. The mechanical behavior and microstructure of these high performance fibers have been characterized, and compared with those fibers produced through conventional spinning conditions. The comparison reveals that both sets of fibers share a common semicrystalline microstructure, but significant differences are apparent in the amorphous region. Besides, high performance fibers show a ground state and the possibility of tuning their tensile behavior. These properties are characteristic of spider silk and not of natural silkworm silk, despite both regenerated and natural silkworm silk share a common composition different from that of spider silk. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Spherulites of Tussah Silk Fibroin. Structure, thermal properties and growth rates

The crystal structure, thermal properties and growth rates of spherulites of the Tussah silk fibroin, produced upon drying of the silk taken directly from the lumen which is essentially a poly(L-alanine)polypeptide, are investigated. Depending on casting conditions, spherulites with either αhelical chain conformation or β parallel sheet structure are produced. The growth rates display a strong positive temperature coefficient, with an apparent transition, which however cannot be related with the formation of two different crystal structures at this stage. This revised version was published online in July 2006 with corrections to the Cover Date.