Nanocrystalline MnO thin film anode for lithium ion batteries with low overpotential

Nanocrystalline MnO thin film has been prepared by a pulsed laser deposition (PLD) method. The reversible lithium storage capacity of the MnO thin film electrodes at 0.125C is over 472 mAh g^?1 (3484 mAh cm^?3) and can be retained more than 90% after 25 cycles. At a rate of 6C, 55% value of the capacity at 0.125C rate can be obtained for both charge and discharge. As-prepared MnO thin film electrodes show the lowest values of overpotential for both charge and discharge among transition metal oxides. All these performances make MnO a promising high capacity anode material for Li-ion batteries.     

A novel anode material of antimony nitride for rechargeable lithium batteries

Antimony nitride thin film has been successfully fabricated by magnetron sputtering method and its electrochemistry with lithium was investigated for the first time. The reversible discharge capacity of Sb₃N/Li cells cycled between 0.3 V and 3.0 V was found above 600 mAh/g. By using transmission electron microscopy and selected area electron diffraction measurements, the conversion reaction of Sb₃N into Li₃Sb and Li₃N was revealed during the lithium electrochemical reaction of Sb₃N thin film electrode. The high reversible capacity and the good cycleability made Sb₃N one of promising anode materials for future rechargeable lithium batteries.     

A Li3V2(PO4)3/C thin film with high rate capability as a cathode material for lithium-ion batteries

A monoclinic lithium vanadium phosphate (Li₃V₂(PO₄)₃) and carbon composite thin film (LVP/C) is prepared via electrostatic spray deposition. The film is studied with X-ray diffraction, scanning and transmission electron microscopy and galvanostatic cell cycling. The LVP/C film is composed of carbon-coated Li₃V₂(PO₄)₃ nanoparticles (50 nm) that are well distributed in a carbon matrix. In the voltage range of 3.0–4.3 V, it exhibits a reversible capacity of 118 mA h g^?1 and good capacity retention at the current rate of 1 C, while delivers 80 mA h g^?1 at 24 C. These results suggest a practical strategy to develop new cathode materials for high power lithium-ion batteries.     

Investigation of immiscible alloy system of Al–Sn thin films as anodes for lithium ion batteries

The Al–Sn, which is immiscible alloy, film was prepared by e-beam deposition to explore the possibility as anode material for lithium ion batteries for the first time. The film has a complex structure with tiny Sn particles dispersed homogeneously in the Al active matrix. The diffusion coefficients of Li⁺ in these Al–Sn alloy films were determined to be 2.1–3.2 × 10⁻⁸ cm²/s by linear sweep voltammetry. The film electrode with high Al content (Al–33wt%Sn) delivered a high initial discharge capacity of 972.8 mA h g⁻¹, while the film electrode with high Sn content (Al–64wt%Sn) with an initial discharge capacity of 552 mA h g⁻¹ showed good cycle performance indicated by retaining a capacity of about 381 mA h g⁻¹ after 60 cycles. Our preliminary results demonstrate that Al–Sn immiscible alloy is a potential candidate for anodic material of lithium ion batteries.     

Structural and electrochemical properties of a porous nanostructured SnO2 film electrode for lithium-ion batteries

A B₂O₃-doped SnO₂ thin film was prepared by a novel experimental procedure combining the electrodeposition and the hydrothermal treatment, and its structure and electrochemical properties were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) analysis, energy dispersive X-ray (EDX) spectroscopy and galvanostatic charge–discharge tests. It was found that the as-prepared modified SnO₂ film shows a porous network structure with large specific surface area and high crystallinity. The results of electrochemical tests showed that the modified SnO₂ electrode presents the largest reversible capacity of 676 mAh g^?1 at the fourth cycle, close to the theoretical capacity of SnO₂ (790 mAh g^?1); and it still delivers a reversible Li storage capacity of 524 mAh g^?1 after 50 cycles. The reasons that the modified SnO₂ film electrode shows excellent electrochemical properties were also discussed.     

Improving the cycleability of Si anodes by covalently grafting with 4-carboxyphenyl groups

In this study, the lithium storage capacity of Si nanoparticles is significantly enhanced by grafting with 4-carboxyphenyl groups via diazonium salts. The modified Si anodes exhibit reversible capacities of 1173 and 527 mA h g^?1 at the 1st and 50th cycle, while those of the bare Si electrodes are only 56 and 62 mA h g^?1, respectively. The improved electrochemical performance is supposed to arise from the formation of a robust and flexible solid electrolyte interface on the surfaces of the modified Si nanoparticles.     

Tremella-like molybdenum dioxide consisting of nanosheets as an anode material for lithium ion battery

Tremella-like structured MoO₂ consisting of nanosheets was obtained via a Fe₂O₃-assisted hydrothermal reduction of MoO₃ in ethylenediamine aqueous solution. The as-prepared product was characterized and tested with scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV) and capacity measurement as anode material for lithium ion batteries. This structured MoO₂ shows very high reversible capacity (>600 mA h g⁻¹), good rate capability and cycling performance, presenting potential application as anode material for lithium ion batteries with high rate capability and high capacity.     

Structural and electrochemical investigation of Li2MgSnO4 anode for lithium batteries

Hexagonal Li₂MgSnO₄ compound was synthesized at 800 °C using Urea Assisted Combustion (UAC) method and the same has been exploited as an anode material for lithium battery applications. Structural investigations through X-ray diffraction, Fourier Transform Infra Red spectroscopy and ⁷Li NMR (Nuclear Magnetic Resonance spectroscopy) studies demonstrated the existence of hexagonal crystallite structure with a = 6.10 and c = 9.75. An average crystallite size of ∼400 nm has been calculated from PXRD pattern, which was further evidenced by SEM images. An initial discharge capacity of ∼794 mA h/g has been delivered by Li₂MgSnO₄ anode with an excellent capacity retention (85%) and an enhanced coulombic efficiency (97–99%). Further, the Li₂MgSnO₄ anode material has exhibited a steady state reversible capacity of ∼590 mA h/g even after 30 cycles, thus qualifying the same for use in futuristic lithium battery applications.     

Perfect reversibility of the lithium insertion in FeS2: The combined effects of all-solid-state and thin film cell configurations

All-solid-state thin film batteries based on sputtered pyrite electrodes, a lithium phosphorus oxynitride electrolyte and a lithium anode were prepared and characterized. The successive reduction of both S₂^2 − and Fe^2 + species led to an impressive volumetric discharge capacity, five times higher than the one for LiCoO₂. Excellent reversibility and capacity retention were obtained during the first and the subsequent 800 charge–discharge cycles. A continuous cycling in the low voltage domain was found to be detrimental to the reversibility of the conversion reaction, suggesting a progressive evolution of the phase distribution inside the electrode. The initial capacity was easily recovered after few full oxidation cycles.     

A Fe-rich sodium iron orthophosphate as cathode material for rechargeable batteries

Phosphate compounds have been intensively investigated as cathode materials for sodium ion batteries. Here we report the synthesis and electrochemical performance of a novel iron-rich sodium iron orthophosphate. This new compound was synthesized by a conventional solid state reaction method, and was found to be electrochemically active, delivering a reversible capacity of 85 mAhg^− 1 at an average voltage of c.a. 3.0 V vs. Na/Na⁺. Besides, the desodiated phase can be (de)intercalated by lithium ions when assembled into a lithium cell. Our discovery will open up the scope of phosphate family and reveal the importance of off-stoichiometric compounds as cathode materials.     

Low-temperature growth of vertically aligned In2O3 nanoblades with improved lithium storage properties

Vertically aligned Indium oxide (In₂O₃) nanoblades are successfully obtained through plasma enhanced chemical vapor deposition (PECVD) approach. By using plasma, the reaction between InCl₃ and O₂ was able to take place, yielding vertically aligned blade like nanostructure. The novel In₂O₃ nanostructures exhibit improved electrochemical properties when used as anode materials for lithium-ion batteries. The In₂O₃ electrode reveals reversible capacity of 580 mAh g^?1 after 100 cycles, much higher than that of the In₂O₃ thin films. The result suggests that proper structural modification of In₂O₃ thin film may contribute to the improvement of electrochemical properties. The In₂O₃ electrodes with large reversible capacity and stable cycling performance may provide new insight of anode materials applied in thin film lithium-ion batteries.     

Three colour electrochromic metallopolymer based on a ruthenium phenolate complex bound to poly(4-vinyl)pyridine

The photonic and electrochemical properties of a novel Ru–phenolate based metallopolymer are reported. The complex undergoes a ruthenium based reversible oxidation at approximately +0.400 V and irreversible box ligand oxidation at +0.800 V vs. Ag/AgCl. Oxidation of thin films in aqueous electrolyte at +0.500 V reversibly switches the colour from wine red to light green and a red orange colour is observed for mixed redox composition. In contrast, oxidation at potentials more positive than +1.500 V shows no visible colour change but produces a change in the near infra-red region. To determine the electrochromic switching rate and to identify the rate determining step of the, scan rate dependent cyclic voltammetry was performed under semi-infinite linear diffusion conditions in aqueous lithium perchlorate. These data reveal that the homogeneous charge transport diffusion coefficient, D_CT, is 3.6 ± 0.2 × 10⁻¹³ cm² s⁻¹, i.e., under these conditions it takes approximately 90 s to fully oxidise a 100 nm thick film.     

Li/LiFePO4 batteries with room temperature ionic liquid as electrolyte

Room temperature ionic liquid (RTIL) was prepared on basis of N-methyl-N-butylpiperidinium bis(trifluoromethanesulfonyl)imide (PP₁₄TFSI), which showed a wide electrochemical window (?0.1–5.2 V vs. Li⁺/Li) and is theoretically feasible as an electrolyte for batteries with metallic Li as anodes. The addition of vinylene carbonate (VC) improved the compatibility of PP₁₄TFSI-based electrolyte towards lithium anodes and enhanced the formation of solid electrolyte interphase film to protect lithium anodes from corrosion. Accordingly, Li/LiFePO₄ cells initially delivered a discharge capacity of about 127 mAh g^?1 at a current density of 17 mA g^?1 in the ionic liquid with the addition of VC and showed better cyclability than in the neat ionic liquid. Electrochemical impedance spectroscopy disclosed that the addition of VC enhanced Li-ion diffusion and depressed interfacial resistance significantly.     

A hierarchical micro/nanostructured 0.5Li2MnO3·0.5LiMn0.4Ni0.3Co0.3O2 material synthesized by solvothermal route as high rate cathode of lithium ion battery

A hierarchical micro/nanostructured Li-rich layered 0.5Li₂MnO₃·0.5LiMn_0.4Ni_0.3Co_0.3O₂ (H-LMNCO) material is prepared for the first time through the development of a solvothermal method, and served as cathode of lithium ion batteries. Electrochemical tests indicate that the H-LMNCO exhibits both a high reversible capacity and an excellent rate capability. The reversible discharge capacity of the H-LMNCO has been measured as high as 300.1 mAh·g^− 1 at 0.2 C rate. When the rate is increased to 10 C, the discharge capacity could still maintain a high value of 163.3 mAh·g^− 1. The results demonstrate that the developed solvothermal route is a novel synthesis strategy of preparing high rate performance Li-rich layered cathode material for lithium ion batteries.     

Nb2O5 nanobelts: A lithium intercalation host with large capacity and high rate capability

In this study, Nb₂O₅ nanobelts, with a ca. ∼15 nm in thickness, ca. ∼60 nm in width and several tens of mircrometers in length, have first been used as the electrode material for lithium intercalation over the potential window of 3.0–1.2 V (vs. Li⁺/Li). It delivers an initial intercalation capacity of 250 mA hg⁻¹ at 0.1 Ag⁻¹ current density, corresponding to x = 2.5 for L_xNb₂O₅, and can still keep relative stable and reaches as large as 180 mA hg⁻¹ after 50 cycles. Surprisingly, the electrodes composed of Nb₂O₅ nanobelts can work smoothly even at high current density of 10 Ag⁻¹, and shows higher specific capacity and excellent cycling stable, as well as sloped feature in voltage profile. Cycling test indicates Nb₂O₅ nanobelts electrode shows a high reversible charge/discharge capacity, high rate capability with excellent cycling stability.     

Hierarchically ordered porous nickel oxide array film with enhanced electrochemical properties for lithium ion batteries

Hierarchically ordered porous nickel oxide array film was prepared by electrodeposition through monolayer polystyrene spheres template. The as-prepared film had a highly porous structure of interconnected macrobowls array possessing nanopores. As anode material for lithium ion batteries, the porous array NiO film exhibited weaker polarization, higher coulombic efficiency and better cycling performance in comparison with the dense NiO film. After 50 cycles, the discharge capacity of porous array NiO film was 518 mAh g^? 1 at 1 C rate, higher than that of the dense NiO film (287 mAh g^? 1). The enhancement of the electrochemical properties was due to the unique hierarchical porous architecture, which provided fast ion/electron transfer and alleviated the structure degradation during the cycling process.     

Preparation and electrochemical lithium storage of flower-like spinel Li4Ti5O12 consisting of nanosheets

In this paper, flower-like spinel Li₄Ti₅O₁₂ consisting of nanosheets was synthesized by a hydrothermal process in glycol solution and following calcination. The as-prepared product was characterized by scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction and cyclic voltammetry. The capacity of the sample used as anode material for lithium ion battery was measured. This structured Li₄Ti₅O₁₂ exhibited a high reversible capacity and an excellent rate capability of 165.8 m Ahg⁻¹ at 8 C, indicating potential application for lithium ion batteries with high rate performance and high capacity.     

Comparison of the electrochemical properties of metallic layered nitrides containing cobalt,nickel and copper in the 1 V–0.02 V potential range

We report the first example of an intercalation compound based on the nitrogen framework in which lithium can be intercalated and deintercalated. A comparison of the structural and electrochemical properties of the ternary lithium cobalt, nickel and copper nitrides is performed. Vacancy layered structures of ternary lithium nitridocobaltates Li_3−2xCo_xN and nitridonickelates Li_3−2xNi_xN with 0.10 ⩽ x ⩽ 0.44 and 0.20 ⩽ x ⩽ 0.60, respectively, are proved to reversibly intercalate Li ions in the 1 V–0.02 V potential range. These host lattices can accommodate up to 0.35 Li ion par mole of nitride. Results herein obtained support Li insertion in vacancies located in Li₂N⁻ layers while interlayer divalent cobalt and nickel cations are reduced to monovalent species. No structural strain is induced by the insertion–extraction electrochemical reaction which explains the high stability of the capacity in both cases. For the Li_1.86Ni_0.57N compound, a stable faradaic yield of 0.30 F/mol, i.e. 130 mAh/g, is maintained at least for 100 cycles. Conversely, the ternary copper nitrides corresponding to the chemical composition Li_3−xCu_xN with 0.10 ⩽ x ⩽ 0.40 do not allow the insertion reaction to take place due to the presence of monovalent copper combined with the lack of vacancies to accommodate Li ions. In the latter case, the discharge of the lithium copper nitrides is not reversible.     

Characterization of SEI layer formed on high performance Si–Cu anode in ionic liquid battery electrolyte

Formation of the SEI layer on Si–Cu film electrode in the ionic liquid electrolyte of 1 M lithium bis(trifluoromethylsulfonyl)imide/1-methyl-1-propylpyrrolidinium bis(trifluoromethylsulfonyl)imide (LiTFSI/MPP-TFSI) was investigated using ex-situ ATR FTIR and X-ray photoelectron spectroscopy. The SEI layer is found to be composed of organic and inorganic compounds that are the decomposition products of MPP cation and TFSI anion, and effectively passivate the electrode surface during initial cycling. Formation of a stable SEI layer leads to an excellent capacity retention 98% of the maximum discharge capacity, delivering discharge capacities of > 1620 mAhg^? 1 over 200 cycles. The data contribute to a basic understanding of SEI formation and composition responsible for the cycling performance of Si-based alloy anodes in ionic liquid electrolyte-based rechargeable lithium batteries.     

A room temperature solid-state rechargeable sodium ion cell based on a ceramic Na-β″-Al2O3 electrolyte and NaTi2(PO4)3 cathode

In this work, a room temperature solid-state rechargeable sodium ion cell, consisting of a ceramic Na-β″-Al₂O₃ thin film as the electrolyte, a NaTi₂(PO₄)₃ gel composite as the cathode and sodium metal as the anode, was developed for the first time. A dense Na-β″-Al₂O₃ thin film with a thickness of approximately 100 μm was obtained by non-toxic and hazard-free ceramic fabrication processes, including tape-casting and subsequent sintering. The solid-state sodium ion cell had a working window of 1.5–2.5 V upon charge-discharge processes and exhibited an extremely stable voltage plateau of approximately 2.1 V. A reversible capacity, based on the NaTi₂(PO₄)₃ cathode, of 133 mAh g^− 1 was observed during the first cycle, which remained approximately 100 mAh g^− 1 after 50 cycles.