表面引发原子转移自由基聚合方法合成Fe3O4/PMMA复合纳米微粒

采用表面引发原子转移自由基聚合方法合成了核壳结构的磁性高分子纳米微粒. 作为聚合反应引发剂的3-氯丙酸, 首先与油酸修饰的Fe3O4纳米微粒表面的部分油酸置换, 然后在Fe3O4纳米微粒表面引发甲基丙烯酸甲酯聚合, 合成的纳米复合材料用TEM, FTIR, XRD和DSC表征. 磁性测试结果表明, 所制备的磁性高分子纳米微粒仍具有超顺磁性, 但由于聚合物的存在, 其饱和磁化强度降低.     

原位聚合法制备具有温敏PNIPAM壳的核-壳结构聚合物纳米微球的研究

结合大分子自组装和原位自由基聚合方法,采用油溶性引发剂偶氮二异丁腈(AIBN),在聚(ε-已内酯)(PCL)纳米粒子表面引发聚合单体N-异丙基丙烯酰胺(NIPAM)和交联剂亚甲基双(丙烯酰胺)(MBA),制备得到了核-壳结构的PCL/PNIPAM聚合物纳米微球.系统研究了单体和交联剂用量、壳层目标交联度、初始PCL/DMF溶液的浓度及引发剂AIBN含量4个反应参数对核-壳结构PCL/PNIPAM纳米微球的PNIPAM壳层得率、微球尺寸、温敏性能及电镜形貌的影响.结果表明,在制备核-壳结构PCL/PNIPAM纳米微球的反应过程中,PCL粒子表面的聚合和水中的聚合二者之间相互竞争.适当增加引发剂AIBN的添加量,有利于制备得到核/壳比例可控的PCL/PNIPAM纳米微球;交联剂MBA较高的反应活性导致形成了非均匀交联的PNIPAM壳层.     

受限空间内聚苯乙烯微粒的制备

以(N,N-二甲氨基-4-吡啶)五氰合铁(II)封端的聚氧丙烯聚氧乙烯共聚物(EPE-Fe)与苯乙烯在水中自组装形成纳米体系(EPE-Fe-St), 在纳米尺度受限空间内进行了苯乙烯自由基聚合, 制备了聚苯乙烯微球(EPE-Fe-PS). 用Fe³⁺对自组装体系的纳米球壳进行固化后形成Fe-EPE-Fe-St 体系, 聚合后也制备了聚苯乙烯微球(Fe-EPE-Fe-PS). 研究结果表明,制备了粒径为60～200 nm 的不同粒径单分散聚苯乙烯微球, 聚合温度对纳米Fe-EPE-Fe-St 体系粒径影响较小, 而对EPE-Fe-St 体系较大. 在受限空间内苯乙烯的自由基聚合可得到数均分子量超过70 万的聚苯乙烯; 自组装体系中引发剂量增多使聚苯乙烯分子量下降, 聚合温度上升也使分子量下降, 而增加自组装的EPE-Fe 用量可增加聚苯乙烯的分子量. 两种受限条件下的聚苯乙烯微球的玻璃化转变温度(T_g)在90～135 ℃之间, 纳米反应器壳层的硬化提高了聚苯乙烯微球的T_g.     

聚苯乙烯/Ag核壳结构纳米微粒的制备及表征

用种子乳液聚合法合成了聚苯乙烯（PS）/Ag复合纳米粒子,进一步利用分步聚合技术实现了聚甲基丙烯酸甲酯(PMMA)在微球表面功能化,分别用TEM、XRD、TG-DTA及FT-IR对其结构和形貌进行了表征,并考察了其摩擦学性能.结果表明,在所选择的实验条件下,合成了以Ag纳米微粒为核,PS、PMMA为壳层的核壳结构复合纳米微球,其中Ag纳米核平均粒径约12 nm,复合微球粒径约25 nm,颗粒较均匀并且在有机溶剂中有良好的分散性,作为润滑油添加剂,具有良好的抗磨性能.     

用ATRP方法制备聚苯乙烯/纳米二氧化硅杂化粒子

采用过量的甲苯-2,4-二异氰酸酯(TDI)对SiO₂纳米粒子表面进行修饰, 将原子转移自由基聚合(ATRP)引发剂引入到SiO₂粒子表面合成大分子引发剂, 采用ATRP技术将聚苯乙烯(PS)大分子链接枝到SiO₂表面制备出以纳米二氧化硅为核, 聚苯乙烯为壳的PS/SiO₂杂化粒子. 利用红外光谱(FTIR)、核磁共振谱( NMR)、凝胶色谱(GPC)等实验手段对杂化粒子及表面接枝聚苯乙烯进行了表征分析.     

光敏性单分散核-壳树莓状PSt/PAM微球制备

采用分散聚合两步加料法,在成核期后向反应体系加入光引发转移终止剂(photo-iniferter)单体2-N,N-二乙基二硫代氨基甲酰氧基乙酸β-甲基丙烯酰氧基乙酯(MAEDCA)制备了核-壳单分散光敏性聚苯乙烯(PSt)微球;进一步,在甲醇介质中,利用光敏性微球在紫外光辐照下引发单体丙烯酰胺(AM)进行表面沉淀接枝聚合,制得了表面亲水、树莓状(raspberry-like)PSt/PAM微球.采用SEM及TEM观察了所得微球的结构和形貌,FTIR、UV-Vis、1H-NMR及XPS分析表明微球的photo-iniferter基团含量随MAEDCA加入量增大而提高,同时补加一定量的MAEDCA、St、AIBN、甲醇及水时所得光敏性PS微球单分散性最好;微球表面接枝PAM后变得亲水并可大量吸附Ag纳米粒子.     

Fe-g-PDEAEMA纳米复合微球的制备及性质研究

由聚N,N-二乙基胺基甲基丙烯酸乙酯(PDEAEMA)与铁纳米颗粒复合制得的纳米铁基复合材料。纳米铁微球表面钝化形成Fe3O4后,将多巴胺基引发剂修饰在Fe3O4的表面,通过表面引发原子转移自由基聚合(SI-ATRP)将DEAEMA单体聚合在修饰了多巴胺基引发剂的表面获得Fe-g-PDEAEMA复合微球。显微结果表明修饰PDEAEMA后,复合微球的分散性得到了一定的提高;XRD数据表明在纳米铁表面生成了一层Fe3O4壳。利用透光率测定研究了复合微球的p H敏感性,表明在酸性条件下悬浮性良好,在碱性条件下发生了沉降,复合微球具有p H敏感性。通过还原降解酸性大红染料,表明Fe-g-PDEAEM复合微球与纳米铁相比,其还原性有所提高,合成的Fe-g-PDEAEMA复合微球可用于氯代烃等氯化物污染的水体保护。     

原子转移自由基聚合原位合成温敏性微球

以过硫酸钾为引发剂、丙酮-水[V(丙酮)∶V(水)＝4∶6]的混合溶剂为反应介质, 在少量二乙烯苯存在的条件下使苯乙烯(St)和对氯甲基苯乙烯(CMSt)进行无皂乳液共聚反应, 得到了粒径大小均匀的交联型聚苯乙烯(PSt)微球, 由X射线光电子能谱对表面组分测定发现: CMSt上的氯原子在聚合过程中富集于交联微球的表面. 以此交联型PSt微球为原子转移自由基聚合(ATRP)的引发剂, 在22 ℃下引发N-异丙基丙烯酰胺(NIPAAm)进行原位ATRP反应, 得到了表面原子转移自由基聚合接枝的交联聚苯乙烯(PNIPAAm-g-PSt)温敏性微球. 借助傅立叶变换红外光谱、差示扫描量热仪、扫描电子显微镜及激光光散射仪等对PNIPAAm-g-PSt的结构、相转变温度、形态及不同温度下的粒径变化进行了测定, 结果表明NIPAAm单体成功地原位ATRP接枝在交联PSt微球的表面, 接枝微球的球形更规整, 在水中的相转变温度约为32 ℃, 具有明显的温度敏感性.     

纳米结构型PMAA/CdS复合微球的微凝胶模板法制备研究

以微凝胶为模板,利用微凝胶三维网络结构对无机沉积反应的限域和导向作用,制备了具有核-壳结构的聚甲基丙烯酸/硫化镉(PMAA/CdS)有机/无机复合微球材料.复合微球的制备包含两个基本步骤首先,以反相乳液聚合法得到包含Cd(Ac)2的聚甲基丙烯酸微凝胶;然后,在搅拌过程中向反应体系中缓慢通人H2S气体,使镉离子沉积为CdS,经洗涤处理后得到PMAA/CdS复合微球.SEM观察表明,复合微球表面呈现均一的微纳米结构,这种结构可因微球制备条件的不同而不同.而且,超声处理可使微球表面趋于光滑.X射线衍射分析表明复合微球中CdS处于晶态,具有立方结构.此外,复合微球因CdS的存在而具有光致发光特性.     

ATRP合成大分子单体法制备核壳结构微球

以α-溴代丙酸乙酯(EPN-Br)为引发剂, N,N, N′,N″,N″-五甲基二亚乙基三胺(PMDETA)为配体,使甲基丙烯酸叔丁酯进行原子转移自由基聚合,合成了端基带溴原子的聚甲基丙烯酸叔丁酯(PtBMA-Br)大分子中间体,通过其与甲基丙烯酸的亲核取代反应,得到了末端C=C双键含量高的大分子单体（MAA-PtBMA）,其相对分子质量可控制在5400-12000g/mol的范围内,分子量分布≤1.20。以偶氮二异丁腈为自由基引发剂,在乙醇中使MAA-PtBMA大分子单体与苯乙烯（St）进行分散共聚,制得了甲基丙烯酸叔丁酯接枝聚苯乙烯（PtBMA-g-PSt）微米级共聚微球,该微球具有核壳结构。     

Controlled fabrication of cross-linked nanoparticles/polymer composite thin films through the combined use of surface-initiated atom transfer radical polymerization and gas/solid reaction

A promising strategy for the controlled synthesis of inorganic/polymeric nanocomposites may be sustained by fabricating cross-linked PbS nanoparticles/polymer composite thin films through combining surface-initiated atom transfer radical polymerization (ATRP) and gas/solid reaction. The introduction of Pb ions through the extension of surface-initiated ATRP to the monomers containing metal ions provides an opportunity for generating nanoparticles on the substrate.     

Novel approach for metallic surface-initiated atom transfer radical polymerization using electrografted initiators based on aryl diazonium salts

This paper reports on the preparation of poly(methyl methacrylate) (PMMA), poly(n-butyl acrylate) (PBA), and polystyrene (PS) brushes at the surface of conducting materials that were modified by the electrochemical reduction of a brominated aryl diazonium salt BF4-, +N2-C6H4-CH(CH3)-Br (D1). The grafted organic species -C6H4-CH(CH3)-Br was found to be very effective in initiating atom transfer radical polymerization (ATRP) of vinyl monomers. This novel approach combining diazonium salts and ATRP allowed PMMA, PBA, and PS brushes to be grown from the surface of iron electrodes. The polymer films were characterized in terms of their chemical structure by infrared reflection absorption spectroscopy and X-ray photoelectron spectroscopy. Atomic force microscopy studies indicated that the polymer brushes are densely packed. Contact angle measurements of water drops on PS and PMMA brushes were 88.1 +/- 2.0 and 70.3 +/- 2.1 degrees, respectively, which is consistent with the published wettability data for the corresponding polymer sheets.     

大分子ATRP引发剂α-卤烷基聚苯乙烯的合成及其引发的丙烯酸丁酯接枝聚合

通过酰基化、还原、酯化和卤代反应 ,在聚苯乙烯上引入α 卤烷基 ,使用FTIR、1 H NMR、1 3C NMR和GPC对产物进行表征 ,结果表明基团转化可以完全进行 ,整个过程中无交联等副反应 .其中α 溴乙基聚苯乙烯可作为原子转移自由基聚合的多功能度引发剂 ,由此引发丙烯酸正丁酯聚合生成梳状聚 (苯乙烯 g 丙烯酸正丁酯 )     

To patterned binary polymer brushes via capillary force lithography and surface-initiated polymerization

An effective approach is described for the synthesis of binary patterned polymer brushes using a combination of capillary force lithography and surface-initiated polymerization. First, the approach calls for an ultrathin polystyrene (PS) mask to be deposited, in a pattern, over a surface to which a layer of polymerization initiator has already been anchored. Next, surface-initiated atom transfer radical polymerization (ATRP) is performed. This can graft the initial polymer brush onto those areas of the surface unprotected by the PS mask. After grafting is complete, the PS mask is removed and a second brush is synthesized on the newly exposed areas.     

基于原子转移自由基聚合制备新型螯合树脂及其吸附性能

以氯甲基化聚苯乙烯树脂(CMPS)为基质, 通过表面引发原子转移自由基聚合(SI-ATRP)反应将聚甲基丙烯酸缩水甘油酯(PGMA)接枝到树脂表面, 再与亚氨基二乙酸(IDA)反应, 制备了一种新型螯合树脂. 采用红外光谱、 元素分析及比表面积与微孔分析仪对其结构进行表征. 树脂表面甲基丙烯酸缩水甘油酯(GMA)接枝量和IDA含量及对Ni(Ⅱ), Cu(Ⅱ)和Pb(Ⅱ)的吸附容量均随聚合时间的延长而增大, 聚合时间为18 h时, 最大吸附容量分别为1.29, 1.19和0.83 mmol/g. 结果表明, SI-ATRP是制备高吸附容量及吸附容量可控的螯合树脂的可行方法.     

Surface initiated ATRP in the synthesis of iron oxide/polystyrene core/shell nanoparticles

A method to prepare magnetic nanoparticles with a covalently bonded polystyrene shell by surface initiated atom transfer radical polymerization (ATRP) was reported. First, the initiator for ATRP was covalently bonded onto the surface of magnetic nanoparticles through our novel method, which was the combination of ligand exchange reaction and condensation of triethoxysilane having an ATRP initiating site, 2-bromo-2-methyl-N-(3-(triethoxysilyl)propyl) propanamide. Then the surface initiated ATRP of styrene mediated by a copper complex was carried out and exhibited the characteristics of a controlled/“living” polymerization. The as-synthesized nanoparticles were coated with well-defined PS of a target molecular weight up to 45 K. These hybrid nanoparticles had an exceptionally good dispersibility in organic solvents and were subjected to detailed characterization using DLS, GPC, FTIR, XPS, UV-vis, TEM and TGA.     

Synthesis and characterization of novel polyacid-stabilized latexes

A series of novel polyacid macromonomers based on 2-hydroxypropyl methacrylate (HPMA) were prepared by atom transfer radical polymerization (ATRP) via a two-step route. First, a range of well-defined PHPMA homopolymer precursors were synthesized by ATRP using a tertiary amine-functionalized initiator, 2-(dimethylamino)ethyl-2-bromoisobutyrylamide, and a CuCl/2, 2'-bipyridine (bpy) catalyst in alcoholic media at 50 °C. ATRP polymerizations were relatively slow and poorly controlled in pure isopropanol (IPA), especially when targeting higher degrees of polymerization (DP > 30). Improved control was achieved by addition of water: low polydispersity (M(w)/M(n) < 1.25) PHPMA homopolymers of DP = 30, 40, 50, 60, or 70 were successfully prepared using a 9:1 w/w % IPA/water mixture at 50 °C. These PHPMA homopolymer precursors were then derivatized to produce the corresponding poly(2-(succinyloxy)propyl methacrylate) (PSPMA) macromonomers by quaternizing the tertiary amine end-group with excess 4-vinylbenzyl chloride, followed by esterification of the pendent hydroxyl groups using excess succinic anhydride at 20 °C. These polyacid macromonomers were evaluated as reactive steric stabilizers for polystyrene latex synthesis under either aqueous emulsion polymerization or alcoholic dispersion polymerization conditions. Near-monodisperse polystyrene latexes were obtained via aqueous emulsion polymerization using 10 wt % PSPMA macromonomer (with respect to styrene monomer) with various initiators as evidenced by scanning electron microscopy, disk centrifuge photosedimentometry and light scattering studies. PSPMA macromomer concentrations as low as 1.0 wt % also produced near-monodisperse latexes, suggesting that these PSPMA macromonomers are highly effective stabilizers. Alcoholic dispersion polymerization of styrene conducted in various ethanol/water mixtures with 10 wt % PSPMA(50) macromonomer produced relatively large near-monodisperse latexes. Increasing the water content in such formulations led to smaller latexes, as expected. Control experiments conducted with 10 wt % PSPMA(50) homopolymer produced relatively large polydisperse latexes via emulsion polymerization and only macroscopic precipitates via alcoholic dispersion polymerization. Thus the terminal styrene group on the macromonomer chains is essential for the formation of well-defined latexes. FT-IR spectroscopy indicated that these latexes contained PSPMA macromonomer, whereas (1)H NMR spectroscopy studies of dissolved latexes allowed stabilizer contents to be determined. Aqueous electrophoresis and X-ray photoelectron spectroscopy studies confirmed that the PSPMA macromonomer chains were located at the latex surface, as expected. Finally, these polyacid-stabilized polystyrene latexes exhibited excellent freeze-thaw stability and remained colloidally stable in the presence of electrolyte.     

Synthesis of mikto‐topology star polymer containing one cyclic arm

Well‐defined mikto‐topology star polystyrene composed of one cyclic arm and four linear arms was synthesized by a combination of atom transfer radical polymerization (ATRP) and Cu‐catalyzed azide‐alkyne cycloaddition (CuAAC) click reaction. First, the bromine‐alkyne α,ω‐linear polystyrenes containing four hydroxyl groups protected with acetone‐based ketal groups were synthesized by ATRP of styrene using a designed initiator. Then, the bromine end‐group was converted to the azide and the linear polystyrene was cyclized intra‐molecularly by the CuAAC reaction. The four hydroxyl groups were released by deprotection and then esterified with 2‐bromoisobutyryl bromide to produce a cyclic polymer bearing four ATRP initiating units. By subsequent ATRP of styrene to grow linear polymers with the cyclic polystyrene as a macroinitiator, the mikto‐topology star polymers were prepared. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Semiconductor nanoparticle/polystyrene latex composite materials

Cadmium sulfide and cadmium selenide/cadmium sulfide core/shell nanoparticles stabilized with poly(cysteine acrylamide) have been bound to polystyrene (PS) latexes by three methods. First, anionic 5 nm diameter CdS particles were electrostatically attached to 130 nm surfactant-free cationic PS latexes to form stable dispersions when the amount of CdS particles was less than 10% of the amount required to form a monolayer on the surface of the PS particles or when the amount of CdS particles exceeded the amount required to form a monolayer on the PS particles. Transmission electron microscopy (TEM) showed nanoparticles on the surface of the latex particles. Fluorescence spectra showed unchanged emission from the nanoparticles. Second, anionic, surfactant-free PS latexes were synthesized in the presence of CdS and CdSe/CdS nanoparticles. TEM showed monodisperse latex particles with trapped nanoparticles. Third, surfactant-stabilized latexes were synthesized by copolymerization of styrene with vinylbenzyl(trimethyl)ammonium chloride electrostatically bound to the CdSe/CdS nanoparticle surface. Brownian motion of the submicroscopic composite particles in water was detected by fluorescence microscopy.     

Covalent immobilization of antibody fragments on well-defined polymer brushes via site-directed method

Well-defined polymer brushes and block copolymer brushes consisting of 2-methacryloyloxyethyl phosphorylcholine (MPC) and glycidyl methacrylate (GMA) were prepared by surface-initiated atom transfer radical polymerization (ATRP). The polymer brushes were used for the immobilization of antibody fragments in a defined orientation. Pyridyl disulfide moieties were introduced to the polymer brushes via a reaction of epoxy groups in GMA units. Fab’ fragments were then immobilized onto these surfaces via a thiol-disulfide interchange reaction and the reactivity of antibodies with antigens was investigated. Antigen/antibody binding on the polymer brushes was more preferable than that on epoxysilane films as a control surface. Furthermore, the activity of the antibodies immobilized on the block copolymer brushes having biocompatible PMPC was greater than that on other surfaces that did not have PMPC in their structures.