氧化钛纳米管阵列制备及形成机理

采用电化学阳极氧化法在HF水溶液体系使纯钛表面形成一层结构规整有序的高密度TiO2纳米管阵列,考察了几种主要的实验参数（阳极氧化电压、温度、时间、电解液浓度）对TiO2纳米管阵列形貌和尺寸的影响.结果表明,阳极氧化电压是影响氧化钛形貌和纳米管尺寸的最主要因素,而温度和电解液浓度只影响TiO2纳米管阵列形成的时间.对TiO2纳米管阵列进行X射线衍射（XRD）和扫描电子显微镜（SEM）的分析,初步表征了TiO2纳米管阵列的电学性质.并讨论了TiO2纳米管的形成机理.     

石墨烯-氧化钌纳米复合材料的水热法合成及电化学电容性能

通过水热法制备了石墨烯-氧化钌(G-RuO₂)纳米复合材料。对样品进行了X射线衍射(XRD),扫描电子显微镜(SEM),透射电子显微镜(TEM)和能量色散谱(EDS)表征。SEM结果表明氧化钌粒子均匀地分散在石墨烯层片上。TEM结果显示氧化钌纳米粒子的平均粒径约为3 nm。对样品进行了循环伏安和充放电性能测试,结果表明在1 A·g^-1的电流密度下,样品在H₂SO₄(1 mol·L^-1)溶液中具有219.7 F·g^-1的比电容。     

自发氧化还原法制备Co3O4/CeO2纳米复合材料及其CO催化氧化反应结构优化

采用简单的自发氧化还原法合成了Co3O4/CeO2纳米复合材料,采用透射电子显微镜(TEM)\,X射线衍射(XRD)及X射线光电子能谱(XPS)等分析手段对样品进行了表征,并探究了反应参数对其催化CO氧化反应活性的影响.结果表明,Co/Ce摩尔比、pH值、反应温度和煅烧温度均显著影响Co3O4/CeO2纳米复合材料的催化性能;性能最优的样品用于催化CO氧化反应在140℃时即可实现100%的转化率,并且在循环测试中其催化活性保持不变,显示出良好的稳定性.     

纳米纤维素基多层级孔道结构碳气凝胶的制备及在锂电池中的应用

采用纳米精磨法对商品桉木浆进行纳米纤丝化处理,得到了高长径比、尺寸均一的纳米纤丝化纤维素(NFC),平均直径为230.10 nm,长度达数十微米.将其组装、干燥后制得具有大量介孔的纳米纤丝化纤维素气凝胶(NFCA).将NFCA在氮气氛围下高温碳化制得碳气凝胶(CNFA),或在氢氧化钾条件下辅助碳化制得具有多层级孔道结构的碳气凝胶(CNFA-A),在保留的碳气凝胶骨架结构上进行孔洞构建.通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)表征及Nanomeasure统计分析,发现NFC的平均直径经碳化后减小到53.16 nm.利用X射线衍射(XRD)、BET比表面积测试和拉曼光谱揭示了碳化处理对纳米纤维素结构、比表面积、石墨化程度和缺陷的影响.结果表明,KOH辅助碳化处理后的碳气凝胶不仅保留了纤维素气凝胶前驱体的网络结构,还在其骨架上二次构建了更多的微孔和介孔,其比表面积高达488.92 m2/g,总孔容为0.404 cm3/g,所得的碳骨架被部分石墨化,具有良好的导电性.这类源于生物质的高比表面积碳气凝胶在被用作锂离子电池(LIB)负极材料时表现出优异的电化学性能,在电流密度1 A/g下连续充放电1000次后比容量达到409 m A·h/g,在电流密度高达20 A/g下,比容量还能维持在219 m A·h/g.     

海绵状纳米结构TiO2膜的制备及其光催化活性

采用电化学阳极氧化法在钛表面构筑了海绵状纳米结构TiO2膜. 应用扫描电子显微镜(SEM)和X射线衍射(XRD)对膜层的形貌和晶型进行了分析和表征, 考察了阳极氧化时间对膜层厚度的影响, 并通过海绵状纳米结构TiO2膜对甲基橙的光催化降解研究了膜层厚度与光催化活性的关系. 结果表明, 海绵状纳米结构TiO2膜对甲基橙具有光催化降解作用, 而且随着膜层厚度的增加, 光催化降解速率显著增大, 厚度为2.2 μm的海绵状纳米结构TiO2膜对甲基橙的光催化降解速率是厚度为480 nm的6.4倍.     

修饰剂链长变化对核壳结构CdS纳米晶尺寸和光学性质的影响

采用液液两相法,在甲苯和水的两相体系中制备了由不同烷基链长单硫醇修饰的具有无机-有机核壳结构的CdS半导体纳米晶.使用透射电子显微镜(TEM)、X射线粉末衍射(XRD)和紫外-可见吸收光谱(UV-Vis)对样品的结构和组成进行了表征.结果表明,样品CdS半导体纳米晶是由无机纳米核及其表面化学吸附的硫醇组成的,而且壳层有机修饰剂对无机纳米核的尺寸和光学性质影响很大.进一步分析发现,层修饰剂的烷基链长和CdS纳米核的尺寸之间存在着类似抛物线的关系.这主要是由于在两相体系中,Cd纳米核的形成和成长两个阶段受到修饰剂在有机相中的迁移率以及其在纳米核表面的组装有序度两种关键因素竞争结果的控制.     

ZnO纳米线阵列的电沉积法制备及表征(英文)

利用直流电沉积方法在多孔氧化铝模板的孔洞中生成锌纳米线,在氧气氛围中,于800°C下氧化2h,将氧化铝中的锌氧化成氧化锌.本研究利用氧气氛围进行锌的氧化,大大提高了传统方法的氧化锌纳米线的制备效率.用场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)和X射线衍射仪(XRD)对其形貌及成分进行表征和分析,结果表明,氧化铝模板的有序孔洞中填充了大尺寸、均匀连续的多晶态氧化锌纳米线.纳米线具有约1000:1的高纵横比,其长度等于氧化铝模板的厚度,直径约为80nm.光致发光(PL)光谱表明,氧化锌纳米线在504nm处有由于氧空位引起的较强蓝绿光发射.这为进一步研究ZnO/AAO组装体发学性质和开发新型功能器件提供了基础.     

甘油-DMSO-H2O中阳极氧化TiO2纳米管阵列的生长与性能

采用NH4F-甘油-DMSO(二甲基亚砜)-H2O溶液体系的电化学阳极氧化法, 在金属钛基板上形成厚度为0.4-1.5 μm的有序TiO2纳米管阵列薄膜. 利用场发射电子扫描显微镜(FESEM)技术, 研究了电解液的组成及阳极氧化电压对TiO2纳米管阵列生长形貌的影响. 结果表明, 阳极氧化电压可以影响TiO2纳米管的径向尺寸和长度；通过改变电解液中DMSO/H2O的体积比, 能够调控纳米管的生成速率与形貌. 利用X射线衍射(XRD)对经过不同温度热处理的TiO2纳米管阵列薄膜的物相进行了分析. TiO2纳米管阵列薄膜的光电催化分解水过程的电压-电流特性测量显示, 光电流密度大于0.2 mA·cm-2.     

三维结构和氧化度对C6位氧化再生纤维素止血材料性能影响

C6位氧化再生纤维素作为可吸收止血材料,其止血性能受材料理化性质的影响。通过比较氧化再生纤维素的吸水率、凝胶化速率、溶解速率、降解速率、抗老化性能和止血效果,研究三维结构和氧化度对氧化再生纤维素性能影响。结果发现,氧化度增高,氧化再生纤维素吸水率增强,凝胶化速率加快,溶解速率和降解速率变快,抗老化性能变差,产品有效期变短。纤丝松散网状多孔结构比纱布致密结构更有利于提高吸水率,加快凝胶化速率和溶解速率;同时降低氧化剂用量,提高抗老化性能。同一氧化度条件下,纤丝止血速率优于纱布,止血效果更好。     

水热合成GdVO4:Eu3+晶体随pH值的形貌和性能演变

使用氧化钆、氧化铕和偏钒酸铵为原料,以DTAB为表面活性剂,在不同的反应溶液pH值条件下,采用水热合成法得到了从微米尺度到纳米尺度的一系列钒酸钆荧光粉。通过X射线衍射(XRD),场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)和荧光光谱(PL)等测试手段对不同形貌的样品的物相及微观形貌和发光性能进行表征。结果表明,在强酸环境下,晶体颗粒较大,为微米级,随着pH值的提升,晶体颗粒尺寸变小,进入纳米级,在pH为7,10时,分别得到50 nm以下的纳米晶片,且分散性良好。另外pH=7时观察到更为微小的小晶粒团,相比之下碱性环境下纳米晶片的结晶度较高。发光性能测试表明,样品发光性能随晶粒尺寸和结晶度变化显著。纳米尺度结晶良好的产品发光性能优异。     

Degradation of TEMPO-oxidized cellulose fibers and nanofibrils by crude cellulase

The biodegradation behavior of 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-oxidized cellulose fibers (TOCs) suspended in water and TEMPO-oxidized cellulose nanofibrils (TOCNs) dispersed in water by a commercial crude cellulase was studied. Products crude cellulase-treated for 0–7 days were separated into water/ethanol-insoluble and -soluble fractions. Weight recovery ratios and viscosity-average degrees of polymerization of the water/ethanol-insoluble fractions clearly decreased with crude cellulase-treatment time, showing that both TOCs and TOCNs have biodegradability. Water/ethanol-soluble fractions were subjected to size-exclusion chromatography (SEC) with photodiode array (PDA) detection to obtain SEC elution patterns detected by reflective index and UV spectra of each SEC pattern elution slice. SEC–PDA and ¹³C-NMR analyses showed that glucuronosyl unit-containing molecules present on microfibril surfaces in TOCs and TOCNs were primarily cleaved by hydrolyzing enzymes present as contaminants in the crude cellulase to form glucuronic acid as one of the major water-soluble degradation compounds. After the glucuronosyl units in TOCs and TOCNs were degraded and removed from microfibril surfaces by the hydrolyzing enzymes, cellulose chains newly exposed on the microfibril surfaces were rapidly hydrolyzed by cellulases predominantly present in the crude cellulase to form cellobiose. Both TOCs and TOCNs having sodium carboxyl groups are thus biodegradable, but TOCN having free carboxyl groups had clearly low biodegradability by the crude cellulase. Thus, biodegradation behavior may be controllable by controlling the structure of carboxyl group counter ions in TOCs and TOCNs.     

Characterization of the supermolecular structure of cellulose in wood pulp fibres

The hierarchic organization of cellulose fibrils (microfibrils) was investigated in holocellulose, sulphite pulp and kraft pulp using TEM, XRD, ED and FTIR. There were remarkable differences in both the fibril structure and fibril aggregation between the samples. TEM observations revealed more intimately associated fibrils in the kraft pulp compared to the sulphite pulp and the holocellulose, results in agreement with previous CP/MAS ¹³C-NMR data [Hult E.-L. et al. (2002) Holzforschung 56: 231–234]. Furthermore, the cellulose crystallinity was higher in the kraft pulp sample. With respect to the cellulose I and I allomorphs, these samples were controversial when different analytical techniques were applied. Due to the small fibril size and the low degree of order of cellulose in these samples, the concept of crystalline triclinic and monoclinic components as determined by diffraction analysis may not be adequate. Instead the fibril can be regarded to have different degrees of lateral order (including paracrystalline ordering) that can be reoriented to I type conformation and packing upon pulping.     

Mechanism and kinetics studies of carboxyl group formation on the surface of cellulose fiber in a TEMPO-mediated system

2,2,6,6-Tetramethylpiperidine-1-oxyl radical (TEMPO) can selectively oxidize primary hydroxyl groups of cellulose to carboxyl groups. However, the depolymerization also occurs during the process. The kinetics and mechanism of carboxyl group formation on the surface of cellulose fiber oxidized by TEMPO/NaClO₂/NaClO were discussed. The oxidization and depolymerization of cellulose occurred simultaneously, according to analysis of FTIR and ¹³C CP/MAS NMR. The glucuronic acid and some small molecular fragments, formed by hydrolysis or β-elimination during the oxidation, are also discussed. The crystallization index increased and crystal size decreased, as shown by X-ray analysis. The degradation steps in the TEMPO/NaClO₂/NaClO system was discussed, according to carbon conversion analyzed by ¹³C CP/MAS NMR. The oxidation of cellulose can be described well by the kinetics model established based on the degradation of cellulose. It was found that temperature is one of the key parameters for controlling the oxdation and degradation level. The possible mechanism for oxidation of cellulose was composed.     

CP/MAS ~(13)C NMR技术对木浆纤维微观结构的研究

利用交叉极化结合魔角旋转技术~(13)C核磁共振法(CP/MAS ~(13)C NMR)对桉木浆纤维的微观结构进行研究,为进一步研究木质纤维素材料开发过程中反应障碍特征奠定基础.通过对NMR光谱C1区(δ 102～108)进行洛仑兹拟合,得到桉木浆纤维中纤维素Iα的相对含量为26.92%,纤维素Iβ的相对含量为52.04%,主要以纤维素Iβ晶体形式为主.通过计算纤维素C4结晶区(δ 86～92)和非结晶区(δ 80～86)的相对含量得到桉木浆的纤维素结晶度为47%.通过洛仑兹和高斯函数的混合模型对NMR光谱C4区(δ 80～92)进行拟合得到基原纤尺寸和微原纤横向尺寸分别为4.0与17.9 nm,并通过计算不同形态的结晶纤维素的相对含量得到纤维素结晶度为51%,证实了在微原纤内部次晶纤维素的存在.     

The influence of hemicellulose on fibril aggregation of kraft pulp fibres as revealed by FE-SEM and CP/MAS 13C-NMR

Three Norway spruce pulps were produced using different kraft pulping methods, in order to obtain large differences in cellulose and hemicellulose proportions at a similar lignin content. The hemicellulose content in the three pulps varied between 10% and 22%. The aim of the study was to evaluate the influence of cellulose and hemicellulose on fibre ultrastructure and correlate this with the differences observed in the mechanical properties between the pulps. The ultrastructure of the pulp fibres were studied using Field Emission Scanning Electron Microscopy (FE-SEM) and Solid-State Cross Polarisation Magic Angle Spinning Carbon-13 Nuclear Magnetic Resonance (CP/MAS ¹³C-NMR) in combination with spectral fitting. CP/MAS ¹³C-NMR measured the average bulk properties of the pulp fibres, while FE-SEM allowed for observations on the ultrastructure of fibre surfaces. The ultrastructure of the fibres varied with varying hemicellulose content. The pulp with a high hemicellulose content had a porous surface structure. In fibres with a low hemicellulose content, the fibril aggregates (macrofibrils) formed a much more compact surface structure. With CP/MAS ¹³C-NMR this change was reflected by an increase in average fibril aggregate width with decreasing hemicellulose content. Results from FE-SEM and CP/MAS ¹³C-NMR correlated well. The changes recorded in ultrastructure may explain the very different mechanical properties reported previously for pulps with different hemicellulose content.     

Quantification of cellulose forms in complex cellulose materials: a chemometric model

In this paper, we present a chemometric model for quantifying the cellulose forms with different states of order found within cellulose I fibrils. The relative amounts of the different cellulose forms, that is crystalline cellulose I, para-crystalline cellulose and cellulose at accessible and inaccessible cellulose surfaces, were determined by non-linear least squares fitting of the C4-region in CP/MAS ¹³C-NMR (Cross-Polarisation Magic Angle Spinning Carbon-13 Nuclear Magnetic Resonance) spectra. By correlating these results from the C4-region with the full spectral data we obtained a model which is able to provide an assessment of the relative amounts of the different cellulose forms directly from NMR-spectra of complex lignocellulosic samples. Furthermore, this model enabled new assignments to be made in the C1-region for signals from cellulose at accessible fibril surfaces.     

Degrees of polymerization (DP) and DP distribution of cellouronic acids prepared from alkali-treated celluloses and ball-milled native celluloses by TEMPO-mediated oxidation

Various cellulose II samples, ball-milled native celluloses and ball-milled wood saw dust were subjected to 2,2,6,6-tetramethypyperidine-1-oxyl radical (TEMPO)-mediated oxidation to prepare cellouronic acid Na salts (CUAs). The TEMPO-oxidized products obtained were analyzed by ¹³C-NMR and size-exclusion chromatography (SEC). When the cellulose II samples with degrees of polymerization (DP) of 220–680 were used as the starting materials, the CUAs obtained had weight-average DP (DPw) values of only 38–79. Thus, significant depolymerization occurs on cellulose chains during the TEMPO-mediated oxidation. These DP values of CUAs correspond to the cellulose II crystal sizes along the chain direction in the original cellulose II samples, but not necessarily to their leveling-off DP values. CUAs can be obtained also from ball-milled native celluloses in good yields by TEMPO-mediated oxidation, although their DPw values are lower than about 80. On the other hand, CUA with DPw of about 170 was obtained from ball-milled wood saw dust.     

CP/MAS 13C-NMR技术对桉木浆纤维素微观结构的研究

利用交叉极化结合魔角旋转技术13C 核磁共振法(CP/MAS ¹³C NMR)对桉木浆纤维的微观结构进行研究, 为进一步研究木质纤维素材料开发过程中反应障碍特征奠定基础. 通过对NMR光谱C1区(δ 102～108)进行洛仑兹拟合, 得到桉木浆纤维中纤维素Iα的相对含量为26.92%, 纤维素Iβ的相对含量为52.04%, 主要以纤维素Iβ晶体形式为主. 通过计算纤维素C4结晶区(δ 86～92)和非结晶区(δ 80～86)的相对含量得到桉木浆的纤维素结晶度为47%. 通过洛仑兹和高斯函数的混合模型对NMR光谱C4区(δ 80～92)进行拟合得到基原纤尺寸和微原纤横向尺寸分别为4.0与17.9 nm, 并通过计算不同形态的结晶纤维素的相对含量得到纤维素结晶度为51%, 证实了在微原纤内部次晶纤维素的存在.     

Physical properties of TEMPO-oxidized bacterial cellulose nanofibers on the skin surface

Water-dispersed bacterial cellulose nanofibers were prepared via an oxidation reaction using 2,2,6,6-tetramethyl-1-piperidine-N-oxy radical (TEMPO) as a catalyst. It was found that TEMPO-oxidized bacterial cellulose nanofibers (TOCNs) synthesized via sodium bromide-free methods are similar to those synthesized using sodium bromide. The TOCNs retained their unique structure in water as well as in emulsion. TOCNs adhere to the skin surface while maintaining nanofibrous structures, providing inherent functions of bacterial cellulose, such as high tensile strength, high water-holding capacity, and blockage of harmful substances. When gelatin gels as model skin were coated with TOCNs, the hardness representing the elasticity was increased by 20% compared to untreated gelatin gel because TOCNs could tightly hold the gelatin structure. When porcine skin was treated with TOCNs, carboxymethyl cellulose, and hydroxyethyl cellulose, the initial water contact angles were 26.5°, 76.5°, and 64.1°, respectively. The contact angle of TOCNs dramatically decreased over time as water penetrated the fibrous structure of the TOCN film. When observed by scanning electron microscopy and confocal microscopy, TOCNs on the skin surface provided physical gaps between particles and the skin, blocking the adsorption of particulate matter to the skin surface. On the contrary, the structure of water-soluble polymers was disrupted by an external environment, such as water, so that particulate matter directly attached to the skin surface. Characterization of TOCNs on the skin surface offered insight into the function of nanofibers on the skin, which is important for their applications with respect to the skin and biomedical research.     

Cellulose nanofibrils as filler for adhesives: effect on specific fracture energy of solid wood-adhesive bonds

Cellulose nanofibrils were prepared by mechanical fibrillation of never-dried beech pulp and bacterial cellulose. To facilitate the separation of individual fibrils, one part of the wood pulp was surface-carboxylated by a catalytic oxidation using (2,2,6,6-tetramethylpiperidin-1-yl)oxyl (TEMPO) as a catalyst. After fibrillation by a high pressure homogenizer, the obtained aqueous fibril dispersions were directly mixed with different urea–formaldehyde-(UF)-adhesives. To investigate the effect of added cellulose filler on the fracture mechanical properties of wood adhesive bonds, double cantilever beam specimens were prepared from spruce wood. While the highest fracture energy values were observed for UF-bonds filled with untreated nanofibrils prepared from wood pulp, bonds filled with TEMPO-oxidized fibrils showed less satisfying performance. It is proposed that UF-adhesive bonds can be significantly toughened by the addition of only small amounts of cellulose nanofibrils. Thereby, the optimum filler content is largely depending on the adhesive and type of cellulose filler used.