CP/MAS ~(13)C NMR技术对木浆纤维微观结构的研究

利用交叉极化结合魔角旋转技术~(13)C核磁共振法(CP/MAS ~(13)C NMR)对桉木浆纤维的微观结构进行研究,为进一步研究木质纤维素材料开发过程中反应障碍特征奠定基础.通过对NMR光谱C1区(δ 102～108)进行洛仑兹拟合,得到桉木浆纤维中纤维素Iα的相对含量为26.92%,纤维素Iβ的相对含量为52.04%,主要以纤维素Iβ晶体形式为主.通过计算纤维素C4结晶区(δ 86～92)和非结晶区(δ 80～86)的相对含量得到桉木浆的纤维素结晶度为47%.通过洛仑兹和高斯函数的混合模型对NMR光谱C4区(δ 80～92)进行拟合得到基原纤尺寸和微原纤横向尺寸分别为4.0与17.9 nm,并通过计算不同形态的结晶纤维素的相对含量得到纤维素结晶度为51%,证实了在微原纤内部次晶纤维素的存在.     

Carbon-13 NMR distinction between categories of molecular order and disorder in cellulose

Differences between values of proton rotating-frame spin relaxation time constants can be exploited to separate a solid-state¹³C NMR spectrum of cellulose into subspectra of crystalline and noncrystalline regions. Variations in chemical shifts and¹³C spin-lattice relaxation time constants can then be used to study variations in molecular order and disorder within each of the two broader categories. Mechanical damage during Wiley milling increases the content of noncrystalline cellulose and changes the nature of molecular disorder within that category. Resolution enhancement of the subspectrum assigned to crystalline cellulose reveals pairs of signals at 83.9 and 84.9 ppm (cellulose I) or 86.8 and 88.3 ppm (cellulose II) assigned to C-4 on well-ordered crystal surfaces. A broader peak in the subspectrum of crystalline cellulose I is assigned to poorly-ordered surfaces. Relative proportions in Avicel microcrystalline cellulose were estimated as: 54% in crystal interiors, 22% on well-ordered surfaces, 8% on poorly-ordered surfaces, 16% in domains of disorder extending more than a few nanometres.     

Molecular conformations at the cellulose–water interface

¹³C-NMR chemical shifts were measured for C-4 and C-6 in a collection of eight crystalline glucoses and glucosides. The influence of the hydroxymethyl conformation was greater at C-4 than at C-6, with mean chemical shifts for gauche–trans molecules displaced 3.1 ppm (C-4) and 2.5 ppm (C-6) relative to gauche–gauche molecules. This information was used to interpret ¹³C-NMR spectra of crystalline celluloses. Chemical shifts for C-4 in the crystallite cores of celluloses I and II differed by just 0.2 ppm, but the corresponding chemical shifts for well-ordered crystallite surfaces differed by 3.0 ppm. The separation between crystallite-surface signals was attributed to different hydroxymethyl conformations at the cellulose–water interface, i.e., gauche–gauche and gauche–trans on crystallites of cellulose I and cellulose II, respectively. A broad C-4 signal in the spectrum of cellulose II indicated gauche–gauche conformations in disordered cellulose. Chemical shifts for C-6 were consistent with these conformations.     

Superhydrophobic surfaces from surface-hydrophobized cellulose fibers with stearoyl groups

In this report, surface-hydrophobized cellulose fibers by stearoyl groups were used for the construction of superhydrophobic surfaces. The product after the synthesis contains two components: cellulose microfibers as the major component and nanoscaled segments in small amounts. The crystalline structure of cellulose was maintained after surface modification based on solid-state ¹³C NMR spectroscopy. Superhydrophobic surfaces showing static water contact angles of >150° were fabricated using freshly prepared products containing both components via the facile route, e.g., solvent casting. The cellulose types, microcrystalline cellulose or cotton linter cellulose fibers, did not significantly affect the chemical modification of cellulose fibers, but the superhydrophobic surfaces using surface-hydrophobized cotton linters as starting materials exhibited higher surface hydrophobicity and better impact stability in comparison to shorter microcrystalline cellulose. Due to the presence of a crystalline cellulose skeleton, the obtained superhydrophobic surfaces are stable during the heat treatment at 80 °C.     

Wood cellulose nanofibrils prepared by TEMPO electro-mediated oxidation

A softwood bleached kraft pulp (SBKP) was subjected to electro-mediated oxidation in water with TEMPO or 4-acetamido-TEMPO without any chlorine-containing oxidant. Solid recovery ratios of water-insoluble fractions of the oxidized SBKPs were more than 80%, and C6-carboxylate contents increased up to approximately 1 mmol g⁻¹ after oxidation for 48 h. Significant amounts of C6-aldehyde groups (0.17–0.38 mmol g⁻¹) were also formed in the oxidized SBKPs. The degree of polymerization decreased from 2,200 to 520 and 1,400 by the oxidation for 48 h with TEMPO at pH 10 and 4-acetamido-TEMPO at pH 6.8, respectively. The original cellulose I crystal structure and crystallinity of SBKP were maintained after the oxidation, indicating that all C6-oxidized groups were selectively formed on crystalline cellulose microfibril surfaces. The oxidized SBKPs with carboxylate contents of more than 0.9 mmol g⁻¹ were convertible to individual cellulose nanofibrils in yields of more than 80% by disintegration in water.     

Concentration enrichment of urea at cellulose surfaces: results from molecular dynamics simulations and NMR spectroscopy

A combined solid-state NMR and Molecular Dynamics simulation study of cellulose in urea aqueous solution and in pure water was conducted. It was found that the local concentration of urea is significantly enhanced at the cellulose/solution interface. There, urea molecules interact directly with the cellulose through both hydrogen bonds and favorable dispersion interactions, which seem to be the driving force behind the aggregation. The CP/MAS ¹³C spectra was affected by the presence of urea at high concentrations, most notably the signal at 83.4 ppm, which has previously been assigned to C4 atoms in cellulose chains located at surfaces parallel to the (110) crystallographic plane of the cellulose Iβ crystal. Also dynamic properties of the cellulose surfaces, probed by spin-lattice relaxation time ¹³CT ₁ measurements of C4 atoms, are affected by the addition of urea. Molecular Dynamics simulations reproduce the trends of the T ₁ measurements and lends new support to the assignment of signals from individual surfaces. That urea in solution is interacting directly with cellulose may have implications on our understanding of the mechanisms behind cellulose dissolution in alkali/urea aqueous solutions.     

Mercerized cellulose biocomposites: a study of influence of mercerization on cellulose supramolecular structure, water retention value and tensile properties

In this study the effect of the mercerization degree on the water retention value (WRV) and tensile properties of compression molded sulphite dissolving pulp was evaluated. The pulp was treated with 9, 10, or 11 % aqueous NaOH solution for 1 h before compression molding. To study the time dependence of mercerization the pulp was treated with 12 wt% aqueous NaOH for 1, 6 or 48 h. The cellulose I and II contents of the biocomposites were determined by solid state cross polarization/magic angle spinning carbon 13 nuclear magnetic resonance (CP/MAS ¹³C NMR) spectroscopy. By spectral fitting of the C6 and C1 region the cellulose I and II content, respectively, could be determined. Mercerization decreased the total crystallinity (sum of cellulose I and cellulose II content) and it was not possible to convert all cellulose I to cellulose II in the NaOH range investigated. Neither increased the conversion significantly with 12 wt% NaOH at longer treatment times. The slowdown of the cellulose I conversion was suggested as being the result from the formation of cellulose II as a consequence of coalescence of anti-parallel surfaces of neighboring fibrils (Blackwell et al. in Tappi 61:71–72, 1978; Revol and Goring in J Appl Polym Sci 26:1275–1282, 1981; Okano and Sarko in J Appl Polym Sci 30:325–332, 1985). Compression molding of the partially mercerized dissolving pulps yielded biocomposites with tensile properties that could be correlated to the decrease in cellulose I content in the pulps. Mercerization introduces cellulose II and disordered cellulose and lowered the total crystallinity reflected as higher water sensitivity (higher WRV values) and poorer stiffness of the mercerized biocomposites.     

Quantum mechanical modeling of the structures, energetics and spectral properties of Iα and Iβ cellulose

Periodic planewave and molecular cluster density functional theory (DFT) calculations were performed on Iα and Iβ cellulose in four different conformations each. The results are consistent with the previous interpretation of experimental X-ray and neutron diffraction data that both Iα and Iβ cellulose are dominantly found in the tg conformation of the hydroxymethyl group with a H-bonding conformation termed “Network A”. Structural and energetic results of the periodic DFT calculations with dispersion corrections (DFT-D2) are consistent with observation suggesting that this methodology is accurate to within a few percent for modeling cellulose. The structural and energetic results were confirmed by comparison of calculated vibrational frequencies against observed infrared and Raman frequencies of Iα and Iβ cellulose. Structures extracted from the periodic DFT-D2 energy minimizations were used to calculate the ¹³C nuclear magnetic resonance chemical shifts (δ¹³C), and the tg/Network A conformations of both Iα and Iβ cellulose produced excellent correlations with observed δ¹³C values.     

Quantum mechanical calculations on cellulose–water interactions: structures,energetics, vibrational frequencies and NMR chemical shifts for surfaces of Iα and Iβ cellulose

Periodic and molecular cluster density functional theory calculations were performed on the Iα (001), Iα (021), Iβ (100), and Iβ (110) surfaces of cellulose with and without explicit H₂O molecules of hydration. The energy-minimized H-bonding structures, water adsorption energies, vibrational spectra, and ¹³C NMR chemical shifts are discussed. The H-bonded structures and water adsorption energies (ΔE_ads) are used to distinguish hydrophobic and hydrophilic cellulose–water interactions. O–H stretching vibrational modes are assigned for hydrated and dry cellulose surfaces. Calculations of the ¹³C NMR chemical shifts for the C4 and C6 surface atoms demonstrate that these δ¹³C4 and δ¹³C6 values can be upfield shifted from the bulk values as observed without rotation of the hydroxymethyl groups from the bulk tg conformation to the gt conformation as previously assumed.     

Exploration on the characteristics of cellulose microfibers from Palmyra palm fruits

To obtain cellulose microfibers from Palmyra palm fruit fibers, a new succession of specific chemical treatments including acidified chlorination, alkalization, and acid hydrolysis have been developed. Cellulose microfibers obtained were characterized by different techniques. The chemical analysis indicated an increase in α-cellulose content and decrease in lignin and hemicellulose for the cellulose microfibers over raw fibers. Fourier transform infrared and ¹³C NMR spectra confirmed the removal of non-cellulosic (lignin and hemicellulose) components after chemical treatments. The X-ray diffraction results revealed that the cellulose I was partly transformed into cellulose II by chemical treatments and the crystallinity index of cellulose microfibers was significantly increased as compared to raw fibers owing to removal of non-cellulosic components. Thermogravimetric analysis results demonstrated that the thermal stability was enhanced noticeably for cellulose microfibers than for the raw fibers. The scanning electron micrographs illustrated cleaner and rough surfaces for the cellulose microfibers when compared to those of raw fibers.     

Hydrogen bonding on accessible surfaces of cellulose from various sources and relationship to order within crystalline regions

Celluloses from a variety of common sources were analyzed for availabilities of O(2)H, O(3)H, and O(6)H in order to estimate the extent of hydrogen bonding on accessible fibrillar surfaces. Celluloses from flax, ramie, sisal, and wood (both cellulose I and II from wood) together with liquid NH₃-swollen cotton and NaOH-swollen cotton (cellulose II) had relative availabilities similar to those of native cotton. Celluloses from Valonia centricosa and in rayon samples stood apart from each other and from the “cotton family.” The difference between Valonia and cotton celluloses appears to result, in addition to the accepted smaller, less perfect crystallites in cotton, from an O(2)H hydrogen bond which is likely the intramolecular bond between O(2)H and O(6′)H that is present in Valonia and absent in cotton. Rayon samples also showed evidence of similar bonds involving O(2)H on accessible surfaces. Since the regenerated rayons had relative availabilities different from those of mercerized cotton and wood cellulose samples, it is proposed that chain packing arrangements are not the same in these two types of cellulose II.     

Phase transformations in microcrystalline cellulose due to partial dissolution

All-cellulose composites were prepared by partly dissolving microcrystalline cellulose (MCC) in an 8.0 wt% LiCl/DMAc solution, then regenerating the dissolved portion. Wide-angle X-ray scattering (WAXS) and solid-state ¹³C NMR spectra were used to characterize molecular packing. The MCC was transformed to relatively slender crystallites of cellulose I in a matrix of paracrystalline and amorphous cellulose. Paracrystalline cellulose was distinguished from amorphous cellulose by a displaced and relatively narrow WAXS peak, by a 4 ppm displacement of the C-4 ¹³C NMR peak, and by values of T₂(H) closer to those for crystalline cellulose than disordered polysaccharides. Cellulose II was not formed in any of the composites studied. The ratio of cellulose to solvent was varied, with greatest consequent transformation observed for c < 15%, where c is the weight of cellulose expressed as % of the total weight of cellulose, LiCl and DMAc. The dissolution time was varied between 1 h and 48 h, with only small additional changes achieved by extension beyond 4 h.     

Mercerization of primary wall cellulose and its implication for the conversion of cellulose I→cellulose II

The mercerization of homogenized primary wall cellulose extracted fromsugar beet pulp was investigated by transmission electron microscopy (TEM),X-ray diffraction together with ¹³C CP-MAS NMR, and FT-IR spectroscopy.For samples resulting from acid extraction, mercerization began at 9% NaOH, whereasfor samples purified by alkaline treatment, the mercerization started at 10%NaOH. The change in morphology when going from cellulose I to cellulose II wasspectacular, as all the microfibrillar cellulose morphology disappeared duringthe treatment. This change in morphology was very drastic as soon as the NaOHconcentrations were increased beyond 8 and 9% for the acid and alkalinepreparedsamples, respectively. On the other hand, the conversion was found to be moreprogressive in terms of increasing NaOH concentration when the transformationwas analyzed by X-ray diffraction or spectroscopy. Our observations of themercerization of isolated cellulose microfibrils are consistent with theconceptof cellulose microfibrils made of parallel chains in cellulose I and crystalsofcellulose II consisting of antiparallel chains.     

Synthesis of cellulose benzoates under homogeneous conditions in an ionic liquid

The ionic liquid 1-allyl-3-methylimidazolium chloride (AmimCl) as a reaction medium was studied for the synthesis of cellulose benzoates by homogeneous acylation of dissolved cellulose with benzoyl chlorides in the absence of any catalysts. Cellulose benzoates with a degree of substitution (DS) in the range from about 1 to 3.0 were accessible under mild conditions. The DS of cellulose derivatives increased with the increase of the molar ratio of benzoyl chloride/anhydroglucose unit (AGU) in cellulose, reaction time, and reaction temperature. Benzoylation of cellulose with some 4-substituted benzoyl chlorides including 4-toluoyl chloride, 4-chlorobenzoyl chloride and 4-nitrobenzoyl chloride was also readily carried out under mild conditions. Furthermore, regioselectively substituted mixed cellulose esters were synthesized in this work. All products were characterized by means of FT-IR, ¹H-NMR, and ¹³C-NMR spectroscopy. In addition, at the end of benzoylation of cellulose, the ionic liquid AmimCl was easily recycled. When the recycled AmimCl was used as the reaction media, the cellulose benzoate with a similar DS was obtained under comparable reaction conditions.     

13C CPMAS NMR investigations of cellulose polymorphs in different pulps

In order to obtain information about the crystallinity and polymorphs of cellulose, and the occurrence of hemicelluloses in pulp fibers, wood cellulose, bacterial cellulose, cotton linters, viscose, and celluloses in different pulps were investigated by solid state ¹³C CPMAS NMR spectroscopy. A mixed softwood kraft pulp and a dissolving-grade pulp were treated under strongly alkaline and acidic conditions and the effect on cellulose crystallinity was studied. The presence of different crystalline polymorphs of cellulose and the amounts of hemicelluloses are considered.     

Studies concerning the accessibility of different allomorphic forms of cellulose

The supramolecular architecture and the morphological structure of cellulose play an important role in its accessibility. In order to evaluate the effect of the crystalline form of organization on the accessibility, we selected cellulosic materials with significant variations in the aforementioned characteristics. The assessment of the accessibility of cellulosic materials was performed experimentally through a water vapor sorption method. The kinetics and the thermodynamic parameters of water vapor sorption process were determined, and a correlation between the Flory–Huggins interaction parameters and the crystallinity index was derived. We concluded that the allomorph involving the most accessible crystal surfaces and amorphous regions was Cellulose II. The correlation of the accessibility values with those of the crystallinity index allowed us to evaluate the accessibility of the allomorphic forms of cellulose at different crystallinity indexes. The obtained experimental data allowed us to quantify the accessibility for crystal surfaces and amorphous regions of the different allomorphs in the order Cellulose II (38%) > Cellulose I (24%) > Cellulose III (10%).     

Model films of cellulose ID – improved preparation method and characterization of the cellulose film

An optimization study of the preparation of spin-coated cellulose model films from the NMMO/DMSO system on silicon wafers has been made. The study shows that the cellulose concentration ID the solution determines the cellulose film thickness and that the temperature of the solution affects the surface roughness. A lower solution temperature results ID a lower surface roughness at cellulose concentrations below 0.8%. Using the described method, ID ID possible to prepare films with thicknesses of 30–90 nm with a constant surface roughness by changing the cellulose concentration, i.e. by dilution with DMSO. On these films, water has a contact angle less than 20° and about 50% of the material can, according to CP/MAS ¹³C-NMR spectroscopy on corresponding fibrous material, be considered to consist of crystalline cellulose ID type material. ID has further been shown that AFM can be used to determine the thickness of cellulose films, ID both dry and wet states. ID this method, the difference ID height between the top surface and the underlying wafer has been measured at an incision made into the cellulose film. The cellulose films have also been spin-coated with the same technique as on the silicon oxide wafer onto the crystal ID a quartz crystal microbalance (QCM). These model films were found to be suitable for swelling measurements with the QCM. The films were very stable during this type of measurement and films with different amounts of charges gave different swelling responses depending on their charges. As expected, films with a higher charge showed a higher swelling.     

Study of cellulose/ethylene diamine/salt systems

To better understand the complex interactions leading to dissolution of cellulose in ethylene diamine (EDA)/salt solvents, studies of interactions in sub systems of solution components and a model system based on cellobiose were conducted. Interaction between EDA and salt cation was investigated through comparison of solvation of K⁺, Na⁺ and Li⁺ in the EDA/H₂O binary solvent system. The least degree of solvation of K⁺ in EDA increased its availability for direct interaction with cellulose. Wide angle X-ray diffraction was utilized to study the interaction between EDA and cellulose. The effect of various solvents on cellulose crystalline polymorph was compared. The results indicated that cellulose was easily accessible to EDA and 1,3-diaminopropane, but was not affected by water or ethanolamine. The effect of salt concentration was investigated using cellobiose as a model compound through HSQC (Heteronuclear Single Quantum Coherence) NMR spectroscopy. Solid state CP/MAS (cross polarization/magic angle spinning) ¹³C NMR spectroscopy was employed to characterize changes in the conformation of the CH₂OH group of cellulose during dissolution. A mechanism scheme of cellulose dissolution in EDA/KSCN systems was proposed based on the information gathered.     

Interaction of cellulose with amine oxide solvents

Cellulose I, mainly as ramie or as Avicel microcrystalline cellulose, has been monitored by optical microscopy and by ¹³C CPMAS NMR, over the course of its dissolution in hot N-methylmorpholine N-oxide solvent. Its interaction with the near-solvent N-ethylmorpholine N-oxide and related non-solvents has also been investigated. NMR shows that N-methylmorpholine N-oxide partly converts crystalline cellulose I into amorphous solid cellulose. The changes in chemical shift imply increased flexibility at the glycosidic bonds. In contrast, N-ethylmorpholine N-oxide converts cellulose I to cellulose III_I, without dissolution. Microscopy shows that the ramie fibres swell laterally, and at least some also shorten longitudinally, during dissolution. Model studies using methyl--d-glucopyranose show no evidence from ¹³C chemical shifts for different modes of binding with different solvents. However, N-methylmorpholine N-oxide binds more strongly to methyl--d-glucopyranose in DMSO than does N-ethylmorpholine N-oxide, whereas N-ethylmorpholine N-oxide binds better to H₂O. Also, ¹³C T ₁ values for aqueous cellobioside show increasing rotational freedom of the –CH₂OH sidechains as N-methylmorpholine N-oxide is added. Together, these observations imply the initial penetration of solvents and near-solvents between the molecular cellulose sheets. Subsequently, N-methylmorpholine N-oxide breaks H-bonds, particularly to O-6, just sufficiently to loosen individual chains and then dissolve the sheets.     

A novel transesterification system to rapidly synthesize cellulose aliphatic esters

Cellulose aliphatic esters (CEs) are important cellulose derivatives that have been widely used in many fields such as plastics, textiles, membranes, etc. However, in traditional methods, long pretreatment and reaction times limit the manufacture of CEs and their widespread application. Herein, a very efficient method for the preparation of CEs in a heterogeneous system was developed. This method involved the transesterification of cellulose with vinyl esters (from C4 to C14) in dimethylsulfoxide under the catalysis of aqueous NaOH. For better understanding of this new reaction system, factors such as the water content, amount of catalyst, reaction temperature and molar ratio of vinyl acetate to the anhydroglucose unit were explored. Results obtained from FT-IR, ¹H and ¹³C NMR spectroscopies confirmed that CEs could be synthesized at 100 °C within 5 min. High water content or excessive amounts of NaOH were detrimental to the synthesis of CEs. Results from small-angle X-ray diffraction showed that the interplanar spacings of these CEs showed an increasing trend with the length of the aliphatic chain. Thermogravimetric analysis and derivative thermogravimetric analysis showed that CEs had higher thermal stability than cellulose. This work provides a new and highly efficient method to synthesize various CEs.