Synthesis of Pt and Pt-Fe nanoparticles supported on MWCNTs used as electrocatalysts in the methanol oxidation reaction

This work reports a feasible synthesis of highly-dispersed Pt and Pt-Fe nanoparticles supported on multiwall carbon nanotubes (MWCNTs) without Fe and multiwall carbon nanotubes with iron (MWCNTs-Fe) which applied as electrocatalysts for methanol electrooxidation. A Pt coordination complex salt was synthesized in an aqueous solution and it was used as precursor to prepare Pt/MWCNTs, Pt/MWCNTs-Fe, and Pt-Fe/MWCNTs using FeCl₂·4NH₂O as iron source which were named S1, S2 and S3, respectively. The coordination complex of platinum (TOA)₂PtCl₆ was obtained by the chemical reaction between (NH₄)₂PtCl₆ with tetraoctylammonium bromide (TOAB) and it was characterized by FT-IR and TGA. The materials were characterized by Raman spectroscopy, SEM, EDS, XRD, TEM and TGA. The electrocatalytic activity of Pt-based supported on MWCNTs in the methanol oxidation was investigated by cyclic voltammetry (CV) and chronoamperometry (CA). Pt-Fe/MWCNTs electrocatalysts showed the highest electrocatalytic activity and stability among the tested electrocatalysts due to that the addition of ”Fe” promotes the OH species adsorption on the electrocatalyst surface at low potentials, thus, enhancing the activity toward the methanol oxidation reaction (MOR).     

A simple one-step preparation of high utilization AuPt nanoparticles supported on MWCNTs for methanol oxidation in alkaline medium

A simple one-step preparation of gold–platinum electrocatalysts supported on multi-walled carbon nanotubes (MWCNTs) with high utilization is reported. A low Pt loading series of bimetallic AuPt/MWCNTs catalysts were prepared by the improved ethylene glycol reduction method, and then they were compared in terms of the electrocatalytic activity for methanol oxidation using cyclic voltammetry (CV) and chronoamperometry in alkaline solutions. The structure of AuPt/MWCNTs was characterized by the transmission electron microscopy (TEM), X-ray diffraction (XRD) and energy-dispersive X-ray spectroscopy (EDS). The results showed high Pt utilization, uniform AuPt nanoparticles size and good electrocatalytic activity for methanol electro-oxidation. The effect of Au/Pt mass ratio on electrocatalytic activity was also investigated by CV and chronoamperometry. The highest peak current density, lowest onset potential and best anti-poisoning effect for methanol electro-oxidation appeared at the Au/Pt/MWCNTs mass ratio of 2:4:32.     

氧化铁对铂在碱性介质中催化氧化甲醇的促进作用

Pt催化剂是电催化领域用途最为广泛的贵金属催化剂.Pt资源稀缺,价格昂贵,同时它的物理化学特性又决定了其在多种催化反应中难以被替代.在质子交换膜燃料电池的小分子醇类电氧化过程中,难免存在Pt的毒化现象,其催化性能有待进一步提升.因此,围绕着Pt催化剂纳米结构的设计、抗毒性及反应机理的探索一直是电催化研究面临的重要课题.目前,已被广泛认可的提高Pt催化性能的方法之一是引入第二种金属,通过金属间协同效应(双功能机理)、张力效应或电子效应等对Pt的催化行为进行改性.对于由双/多金属组成的纳米结构催化剂,无论是协同效应还是电子效应,催化活性的提高都需要金属间有丰富的接触界面和恰当的邻近状态.通过调变两组元的种类、原子比和接触状态等可以实现对金属-金属界面的调控,进而调变催化剂性能.除金属助剂外,金属氧化物对Pt催化剂的助催化作用也引起广泛关注.由于金属氧化物与Pt之间的密切接触作用,氧化物的形貌特点对Pt的催化性能可产生重要影响.到目前为止,有关催化剂形貌效应的研究主要集中于贵金属纳米颗粒上(Pt,Au,Pd等),但关于金属氧化物载体/助剂的形貌对贵金属催化性能影响的研究尚不多.具有明确形貌的金属氧化物载体/助剂,暴露的晶面不同,表面原子的配位状态也不同,从而造成与之密切接触的Pt的性质发生改变.因此,金属氧化物的表面性质以及Pt-金属氧化物的界面性质将对电催化性能产生重要影响,深入阐释贵金属-金属氧化物的表/界面性质以及建立有效的构效关系,对设计和制备高效电催化剂具有一定的指导意义.为了提高Pt基催化剂活性、抗CO中毒能力以及稳定性,本文采用共沉淀法和水热法分别制备了纳米棒和六边形纳米片状的Fe2O3作为Pt催化剂的助剂,考察了助剂形貌对Pt催化剂在碱性介质中催化氧化甲醇的促进作用.通过X射线衍射、扫描电子显微镜、透射电子显微镜、X射线光电子能谱以及电化学技术对催化剂进行了表征.结果显示,Fe2O3的存在能显著提高Pt催化剂在碱性介质中对甲醇氧化的电催化性能,而且以Fe2O3纳米棒为助剂制备的Pt-Fe2O3/C-R催化剂催化活性以及稳定性比Fe2O3纳米片为助剂制备的Pt-Fe2O3/C-P催化剂更高.这种促进效应可能与助剂Fe2O3的形态有关.Pt-Fe2O3/C-R催化剂中Pt的质量比活性为5.32 A/mgPt,本征活性为162.7 A/m2Pt,分别是Pt-Fe2O3/C-P催化剂的1.67和2.04倍,是商业PtRu/C样品的4.19和6.16倍.协同效应和电子效应是Pt催化性能提升的主要原因.此外,Pt-Fe2O3/C-R样品中高价态Pt的含量较高,可能也是加速甲醇氧化反应动力学的原因之一.高价态的Pt可能会增强甲醇分子在Pt表面的吸附强度,促进Pt上甲醇氧化反应初始步.这些发现不仅可对甲醇电催化氧化机理有了更深的理解,而且对设计和制备高性能甲醇氧化电催化剂也具有一定的指导意义.     

Fe对Pt-Fe/C催化剂电催化氧还原反应活性的影响

制备了用作直接甲醇燃料电池的碳载Pt-Fe(Pt-Fe/C)阴极催化剂, X射线能量色散谱(EDX)、X射线衍射谱和电化学测量的结果表明, 在Pt-Fe/C催化剂中, Fe以3种形式存在. 质量分数大约为20％的Fe进入Pt的晶格, 形成Pt-Fe合金, 质量分数大约为80％的Fe没有进入Pt的晶格而以Fe和Fe2O3的形式单独存在. 该催化剂经酸处理后, 非合金化Fe和Fe2O3被溶解, 而使Pt-Fe/C催化剂的电化学活性比表面积要比未经酸处理前的增加约30％左右, 导致Pt-Fe/C催化剂对氧还原的电催化活性优于未经酸处理前的Pt-Fe/C催化剂. 研究结果表明, Pt-Fe/C催化剂的电化学活性比表面积对氧还原的电催化活性起重要的作用, 另外, 只有与Pt形成合金的Fe能提高Pt对氧还原的电催化活性, 而非合金化的Fe对Pt催化剂对氧还原的电催化活性基本没有影响.     

Electrocatalytic activity of porous nanostructured Fe/Pt-Fe electrode for methanol electrooxidation in alkaline media

An electrochemical approach to fabricate a nanostructured Fe/Pt-Fe catalyst through electrodepo-sition followed by galvanic replacement is presented. An Fe/Pt-Fe nanostructured electrode was prepared by deposition of Fe-Zn onto a Fe electrode surface, followed by replacement of the Zn by Pt at open-circuit potential in a Pt-containing alkaline solution. Scanning electron microscopy and energy-dispersive X-ray techniques reveal that the Fe/Pt-Fe electrode is porous and contains Pt. The electrocatalytic activity of the Fe/Pt-Fe electrode for oxidation of methanol was examined by cyclic voltammetry and chronoamperometry. The electrooxidation current on the Fe/Pt-Fe catalyst is much higher than that on flat Pt and smooth Fe catalysts. The onset potential and peak potential on the Fe/Pt-Fe catalyst are more negative than those on flat Pt and smooth Fe electrodes for methanol electrooxidation. All results show that this nanostructured Fe/Pt-Fe electrode is very attractive for integrated fuel cell applications in alkaline media.     

高利用率多壁碳纳米管负载金铂合金纳米粒子催化剂在碱性溶液中的甲醇电催化氧化性能研究

使用乙二醇还原法合成了一系列高利用率多壁碳纳米管负载的金铂双金属纳米粒子电催化剂,在碱性溶液中由循环伏安和计时电流法测试该AuPt催化剂对于甲醇氧化反应的电催化活性.透射电子显微镜、X射线衍射与X射线能谱观测催化剂形貌,表征催化剂结构.结果表明,金铂双金属纳米粒子均匀分散在碳纳米管上,催化剂具有良好甲醇电氧化性能.实验表明Au/Pt/MWCNTs比为10∶8∶32(bymass)时,该催化剂具有最高甲醇电氧化峰电流密度与最负起始氧化电位.     

多孔纳米结构Fe/Pt-Fe电极对碱性介质中甲醇电氧化的催化活性（英文）

An electrochemical approach to fabricate a nanostructured Fe/Pt-Fe catalyst through electrodeposition followed by galvanic replacement is presented. An Fe/Pt-Fe nanostructured electrode was prepared by deposition of Fe-Zn onto a Fe electrode surface, followed by replacement of the Zn by Pt at open-circuit potential in a Pt-containing alkaline solution. Scanning electron microscopy and energy-dispersive X-ray techniques reveal that the Fe/Pt-Fe electrode is porous and contains Pt. The electrocatalytic activity of the Fe/Pt-Fe electrode for oxidation of methanol was examined by cyclic voltammetry and chronoamperometry. The electrooxidation current on the Fe/Pt-Fe catalyst is much higher than that on flat Pt and smooth Fe catalysts. The onset potential and peak potential on the Fe/Pt-Fe catalyst are more negative than those on flat Pt and smooth Fe electrodes for methanol electrooxidation. All results show that this nanostructured Fe/Pt-Fe electrode is very attractive for integrated fuel cell applications in alkaline media.     

炭黑负载Pt-Fe双金属催化剂对甲醇的电催化氧化性能

采用浸渍还原法制备了炭黑负载Pt及Pt-Fe双金属催化剂,通过X光衍射、扫描电镜及X射线光电子能谱对催化剂进行了表征.利用循环伏安法和计时电流法研究了溶液pH值和Pt/Fe原子比对Pt-Fe/C催化剂的甲醇电催化氧化活性与稳定性的影响.结果显示,当溶液pH值为9.0,Pt/Fe原子比为1∶1时,所得Pt-Fe/C催化剂对甲醇的电催化氧化活性与稳定性明显优于Pt/C催化剂.Fe的引入不仅提高了Pt粒子的分散与电化学活性表面积,而且有利于富Pt表面的形成,从而提高了Pt的有效利用率与催化性能.     

聚乙酰苯胺修饰碳纳米管载铂催化剂对甲醇电催化氧化

以原位化学聚合的聚乙酰苯胺/多壁碳纳米管(PAANI-MWCNTs)复合纳米材料作为载体,采用硼氢化钠还原法将Pt纳米粒子担载到PAANI-MWCNTs复合纳米材料表面,制备了Pt/PAANI-MWCNTs复合纳米催化剂.样品的结构和形貌用紫外-可见(UV-Vis)光谱、拉曼光谱、扫描电镜(SEM)、透射电镜(TEM)和X射线衍射(XRD)进行了表征.结果表明,聚乙酰苯胺与碳纳米管之间存在较强的π-π相互作用,使其能牢固地吸附于多壁碳纳米管表面,对碳纳米管的结构完整性和导电性有一定的改善作用.同时,金属Pt纳米颗粒较为均匀地分散在PAANI-MWCNTs表面,粒径分布范围较窄.采用循环伏安法和计时电流法在酸性溶液中研究了Pt/PAANI-MWCNTs催化剂对甲醇的电催化氧化活性,结果表明Pt/PAANI-MWCNTs复合纳米催化剂比用混酸处理的碳纳米管载铂催化剂对甲醇呈现出更高的电催化氧化活性和更好的抗中毒能力及稳定性.     

Synthesis and characterization of platinum catalysts on multiwalled carbon nanotubes by intermittent microwave irradiation for fuel cell applications

Pt electrocatalysts supported on multiwalled carbon nanotube (Pt/MWCNT) nanocomposites have been synthesized by a rapid intermittent microwave irradiation (IMI) technique for polymer electrolyte and direct methanol fuel cells (PEFCs and DMFCs), using H(2)PtCl(6) as Pt precursor. The Pt/MWCNT nanocomposites are characterized by XRD, XPS, and TEM. The results indicate that Pt particle size and distribution on the MWCNT support are affected significantly by the oxidation treatment of MWCNTs, the IMI procedure, and the MWCNT tube diameter or surface area. The PtO(x) (x = 1, 2) species was first deposited on the surface of MWCNTs by the IMI and subsequently reduced to Pt(0) with refluxing in the presence of HCOOH. Pt/MWCNT nanocomposites synthesized by this IMI method have achieved extremely uniform dispersed Pt nanoparticles with a particle size of approximately 3 nm. Electrochemical measurement indicates that Pt/MWCNT nanocomposites synthesized by the IMI method display a significantly higher electrochemically active area and higher catalytic activity for the methanol oxidation reaction in comparison to a commercial Pt/C catalyst.     

PtRu nanoparticles supported on 1-aminopyrene-functionalized multiwalled carbon nanotubes and their electrocatalytic activity for methanol oxidation

A new synthesis method for the preparation of high-performance PtRu electrocatalysts on multiwalled carbon nanotubes (MWCNTs) is reported. In this method, bimetallic PtRu electrocatalysts are deposited onto 1-aminopyrene (1-AP)-functionalized MWCNTs by a microwave-assisted polyol process. The noncovalent functionalization of MWCNTs by 1-AP is simple and can be carried out at room temperature without the use of expensive chemicals or corrosive acids, thus preserving the integrity and the electronic structure of MWCNTs. PtRu electrocatalysts on 1-AP-functionalized MWCNTs show much better distribution with no formation of aggregates, higher electrochemically active surface area, and higher electrocatalytic activity for the electrooxidation of methanol in direct methanol fuel cells as compared to that on conventional acid-treated MWCNTs and carbon black supported PtRu electrocatalysts. PtRu electrocatalysts on 1-AP-functionalized MWCNTs also show significantly enhanced stability.     

Promoting performance and CO tolerance of Pt nanocatalyst for direct methanol fuel cells by supporting on high-surface-area silicon carbide

SiC-supported Pt nanocatalyst was prepared by electrodeposition of Pt nanoparticles on the surface of high-surface-area SiC, which was fabricated by a versatile carbothermal reduction method. Characterization studies show that such synthesis protocol leads to well distribution of Pt nanoparticles, with a mean particle size of 2.9 nm on the support. This catalyst has been electrochemically characterized toward methanol oxidation, which exhibits higher catalytic activity, durability, and electrochemical active surface area than the electrodeposited Pt on multiwalled carbon nanotubes (MWCNTs). Further investigation reveals that the SiC-supported Pt also shows superior CO tolerance to Pt/MWCNTs. These results suggest that high-surface-area SiC could be a promising supporting material for constructing high-performance methanol oxidation electrocatalysts.     

Pt/RuO2/CNTs纳米催化剂中RuO2含量对甲醇电催化氧化性能的影响

制备了一种新的甲醇直接燃料电池Pt/RuO2/CNTs阳极催化剂,在相同Pt负载量下,其甲醇电催化氧化活性是Pt/CNTs的3倍.采用循环伏安法研究发现Pt/RuO2/CNTs纳米催化剂中RuO2含量对甲醇电催化氧化活性有明显影响,当Pt和RuO2在碳纳米管上含量分别为15%和9.5%时,Pt/RuO2/CNTs催化剂具有最佳的甲醇电催化氧化活性.RuO2负载在碳纳米管上比电容的变化,反映了水合RuO2结构中质子与电子传输平衡的能力,分析表明,催化剂中RuO2含量不同导致电容的变化是影响甲醇电催化氧化活性的主要原因.当催化剂结构中质子与电子传输达到平衡时,催化剂比电容最大,电催化氧化活性最高.这种基于电容关联电催化剂的观点对甲醇直接燃料电池阳极催化剂的设计非常有意义.     

导电共聚物衍化新策略制备硫、氮共掺杂碳纳米管及其对改善PtCu纳米晶分散性与甲醇电催化氧化的促进作用

有效调控碳纳米材料的几何和电子结构的协同效应和缺陷是获得优良电化学性能的关键.然而,如何设计一种具有优势结构的杂化材料及对其电催化机理的认识尚不清楚.本文提出了一种聚(3,4-乙撑二氧噻吩)/聚苯胺导电共聚物热解策略来制备S和N共掺杂多壁碳纳米管(MWCNTs),发现改变前驱体溶液中两种单体的比例可以调控掺杂MWCNTs中S和N原子的含量与表面活性位结构.S和N的共掺杂明显增大了碳纳米管表面的缺陷程度并暴露出更丰富的活性位点,从而有利于超细Pt和PtCu纳米颗粒的均匀分布和沉积.透射电镜和扫描透射电镜结果表明,所制备S和N共掺杂MWCNTs(SN-MWCNTs)负载的催化剂中Pt和PtCu纳米颗粒以及掺杂的S和N原子都均匀地分布在MWCNTs上,且沉积的Pt和PtCu纳米颗粒的平均尺寸仅分别为2.30和2.87 nm.X射线光电子能谱结果表明,S和N共掺杂MWCNTs与负载的Pt基纳米颗粒之间存在强烈的电荷转移相互作用,明显改变了贵金属Pt的表面电子结构.电化学测试结果表明,与Pt/SN-MWCNTs,Pt/N-MWCNTs,Pt/S-MWCNTs和商业Pt/C催化剂相比,Pt₁Cu₂/SN-MWCNTs表现出更大的电化学活性表面积(148.85 m² g^?1),更高的甲醇氧化质量活性(1589.9 mA mg_Pt^?1)、电化学稳定性和抗CO毒化能力.密度泛函理论研究表明,S和N共掺杂导致碳纳米管极大地变形,同时极化和激活了相邻的C原子.因此,增强了Pt₁Cu₂纳米颗粒在SN-MWCNTs上的吸附以及随后甲醇分子的吸附.此外,Pt₁Cu₂/SN-MWCNTs对甲醇氧化的电催化活性均在热力学和动力学上优于相应的CNTs和N-CNTs基材料.本文提供了一种新颖的在碳基材料上构建高度分散且稳定的Pt基纳米颗粒高性能燃料电池电催化剂的方法.     

In situ synthesis of Pt/carbon nanofiber nanocomposites with enhanced electrocatalytic activity toward methanol oxidation

Pt/carbon nanofiber (Pt/CNF) nanocomposites were facilely synthesized by the reduction of hexachloroplatinic acid (H(2)PtCl(6)) using formic acid (HCOOH) in aqueous solution containing electrospun carbon nanofibers at room temperature. The obtained Pt/CNF nanocomposites were characterized by TEM and EDX. The Pt nanoparticles could in situ grow on the surface of CNFs with small particle size, high loading density, and uniform dispersion by adjusting the concentration of H(2)PtCl(6) precursor. The electrocatalytic activities of the Pt/CNF nanocomposites were also studied. These Pt/CNF nanocomposites exhibited higher electrocatalytic activity toward methanol oxidation reaction compared with commercial E-TEK Pt/C catalyst. The results presented may offer a new approach to facilely synthesize direct methanol fuel cells (DMFCs) catalyst with enhanced electrocatalytic activity and low cost.     

Electrodeposition and electrocatalytic properties of platinum nanoparticles on multi-walled carbon nanotubes: effect of the deposition conditions

Platinum (Pt) nanoparticles were electrochemically deposited on multi-walled carbon nanotubes (MWCNTs) through a three-step process, including an electrochemical treatment of MWCNT, electro-oxidation of PtCl₄ ²⁻ to Pt(IV) complex, and an electro-conversion of Pt(0) on MWCNT. The effect of formation conditions for Pt(IV) complexes on the Pt nanoparticals transformed was investigated. The structure and elemental composition of the resulting Pt/MWCNT electrode were characterized by transmission electron micrograph (TEM) and energy dispersive X-ray spectroscopy (EDX). The electrocatalytic properties of the resulting Pt/MWCNT electrode for methanol oxidation have been investigated. The high electrocatalytic activity and good stability of Pt/MWCNT electrode may be attributed to the high dispersion of platinum nanoparticles and the particular properties of the MWCNT supports.     

高催化活性Pd-Co3O4/MWCNTs催化剂对甲醇氧化的电催化性能

以Co(NO3)3·6H2O为钴源,聚乙二醇(PEG)20000为表面活性剂,与多壁碳纳米管(MWCNTs)混合后通过水热氧化法成功地合成了表面均匀分布纳米絮状Co3O4的MWCNTs复合物,进一步还原Pd的前驱体而制备得到Pd-Co3O4/MWCNTs复合催化剂.利用扫描电镜(SEM)、透射电镜(TEM)及X射线粉末衍射(XRD)等手段对样品的形貌和晶型结构进行了表征,结果表明Pd纳米粒子为面心立方晶体结构,均匀地分布在Co3O4修饰的MWCNTs表面.用循环伏安法和计时电流法表征结果表明:催化剂Pd-Co3O4/MWCNTs具有较大的电化学活性表面积,在碱性介质中对甲醇氧化具有更高的电催化活性和稳定性.研究结果表明,过渡金属氧化物纳米Co3O4颗粒在提高直接甲醇燃料电池(DMFC)催化性能研究中具有十分重要的作用,是一类很有潜力的载体催化剂.     

PDDA修饰的碳纳米管载铂电催化剂的合成及其在碱性条件下的氧气还原反应催化性能

采用长链聚合物聚二烯丙基二甲基氯化铵(PDDA)对多壁碳纳米管(MWCNTs)进行修饰,并将采用胶体法还原出的铂(Pt)纳米粒子通过静电作用担载于PDDA修饰的多壁碳纳米管上,从而制备出Pt/PDDA/MWCNTs复合电催化剂.透射电镜(TEM)与X射线衍射(XRD)测试结果表明, Pt纳米粒子均匀地分布在MWCNTs的表面,其平均粒径约为3.6 nm.热失重分析显示催化剂的实际负载量为36%(w).旋转圆盘电极测试结果表明, Pt/PDDA/MWCNTs催化剂对碱性条件下的氧气还原反应(ORR)具有优异的催化活性.与负载量为40%(w)的商业Pt/C催化剂相比, Pt/PDDA/MWCNTs催化剂的氧气还原反应的起始电位和半波电位均正移约30 mV,其质量比活性更大.动力学研究结果进一步证实Pt/PDDA/MWCNTs催化剂比负载量为40%(w)的商业Pt/C催化剂在碱性条件下对氧气还原反应具有更优异的催化活性.     

Revealing the Effect of Surface Composition on Multiwalled Carbon Nanotubes Supported Pt-Fe Alloy Electrocatalysts for Methanol Oxidation Performance

The designs of efficient and inexpensive Pt-based catalysts for methanol oxidation reaction (MOR) are essential to boost the commercialization of direct methanol fuel cells. Here, the highly catalytic performance PtFe alloys supported on multiwalled carbon nanotubes (MWCNTs) decorating nitrogen-doped carbon (NC) have been successfully prepared via co-engineering of the surface composition and electronic structure. The Pt₁Fe₃@NC/MWCNTs catalyst with moderate Fe³⁺ feeding content (0.86 mA/mg_Pt) exhibits 2.26-fold enhancement in MOR mass activity compared to pristine Pt/C catalyst (0.38 mA/mg_Pt). Furthermore, the CO oxidation initial potential of Pt₁Fe₃@NC/MWCNTs catalyst is lower relative to Pt/C catalyst (0.71 V and 0.80 V). Benefited from the optimal surface compositions, the anti-corrosion ability of MWCNT, strong electron interaction between PtFe alloys and MWCNTs and the N-doped carbon (NC) layer, the Pt₁Fe₃@NC/MWCNTs catalyst presents an improved MOR performance and anti-CO poisoning ability. This study would open up new perspective for designing efficient electrocatalysts for the DMFCs field.     

Anchoring metal nanoparticles on hydrofluoric acid treated multiwalled carbon nanotubes as stable electrocatalysts

We attempted the treatment of multiwalled carbon nanotubes (MWCNTs) in hydrofluoric acid (HF) aqueous solution for depositing Pt nanoparticles as catalysts for methanol oxidation for the first time. The preliminary results revealed that the Pt nanoparticles could be well dispersed on HF treated MWCNTs and gave enhanced activity and stability for methanol oxidation. As demonstrated in this study, the Pt supported on HF treated MWCNTs catalyst gave over doubled current density than that of Pt supported on as-received MWCNTs for methanol oxidation at the same Pt loadings. The enhancement in the stability of the Pt supported on HF treated MWCNTs catalyst for methanol oxidation is believed due to the stronger interaction between Pt nanoparticles and MWCNTs. This study opens promising possibilities for anchoring metal nanoparticles on the walls of the MWCNTs uniformly and stably.