可见光照射下负载2,2´-联吡啶铁(II)的层状粘土催化剂活化分子氧降解染料污染物

在可见光照射下, 负载有2,2´-联吡啶铁(II)络合物的Laponite粘土能够有效地活化分子氧降解染料罗丹明B, 在水溶液中的2,2´-联吡啶铁(II)络合物则没有任何光催化活性. 该催化剂能够循环降解罗丹明B并且保持很好的光催化活性, 粘土催化剂易于通过离心或者沉降从体系中分离. 测定了光催化剂降解罗丹明B的TOC去除率和体系中的活性氧物种, 并且对催化反应机理进行了讨论.     

静电纺丝制备g-C3N4/C纳米纤维及其可见光降解性能

采用g-C_3N_4纳米片与聚丙烯腈进行静电复合纺丝,再经预氧化和碳化制得g-C_3N_4/C纳米纤维。利用傅立叶变换红外光谱仪(FTIR)、X射线衍射仪(XRD)、拉曼光谱(Raman)和扫描电子显微镜(SEM)对样品结构和形貌进行表征,通过紫外-可见漫反射光谱(UV-Vis DRS)分析可见光响应性。研究表明,复合纳米纤维对罗丹明B表现出较好的可见光降解活性,源于无定形相/石墨相混合结构的碳基体能够降低g-C_3N_4的光生电子-空穴对复合的几率。复合纳米纤维膜在光催化降解搅拌条件下始终能保持完整,经过多次回收和光催化实验,对罗丹明B的光降解率依然较高,表现出较优异的循环利用稳定性。     

Keggin型铜取代磷钨杂多阴离子可见光催化降解罗丹明B

以Keggin型铜取代杂多阴离子PW11O39Cu(Ⅱ)(H2O)5-[PW11Cu]为可见光催化剂,有机染料罗丹明B(RhB)为模型污染物,研究了在可见光照射下PW11Cu对RhB的可见光催化降解作用,提出了PW11Cu可见光催化作用的反应机理,同时考察了RhB初始浓度、PW11Cu初始浓度和溶液pH值对RhB光催化降解速率的影响。 实验结果表明,含有15.6 μmol/L PW11Cu+10 μmol/L RhB的水溶液在可见光照射下反应80 min,RhB的降解率达100%,总有机碳去除率约33%。 RhB的可见光催化降解服从准一级动力学方程,在RhB初始浓度为20、30和40 μmol/L的情况下,其表观一级速率常数分别为3.1×10-2、2.0×10-2和1.5×10-2 min-1。     

酞菁敏化混晶TiO2薄膜的低温制备及其对罗丹明B的催化降解

以四磺酸酞菁铜(CuPcTs)为敏化剂,采用溶胶-凝胶法制备了酞菁敏化的TiO2溶胶,经浸渍提拉成膜并室温晾干,制得CuPcTs-TiO2薄膜.采用XRD,UV-Vis和SEM等测试手段对薄膜样品进行了表征,并通过罗丹明B的降解考察了薄膜的可见光催化性能.结果表明,TiO2为锐钛矿-板钛矿-金红石混晶结构,CuPcTs-TiO2薄膜对罗丹明B降解具有较高的光催化活性.CuPcTs敏化能有效提高TiO2的可见光催化活性,但过多的CuPcTs会使催化活性降低.在可见光照射条件下,罗丹明B主要是先脱乙基生成罗丹明,然后再逐步被分解.CuPcTs-TiO2薄膜在经2～3次循环使用后,其光催化活性趋于稳定.CuPcTs可牢固地负载于TiO2薄膜中,从而保证了CuPcTs-TiO2薄膜重复使用的稳定性.     

负偏压下Ag@AgBr/Ni膜电极光电催化降解罗丹明B的性能和机理

用电化学方法制备Ag@Ag Br/Ni表面等离子体薄膜电极,以扫描电子显微镜(SEM)、X射线衍射(XRD)和紫外-可见漫反射光谱(UV-Vis DRS)对薄膜的表面形貌、晶相结构、光吸收特性进行了表征,在负偏压和可见光作用下,以罗丹明B为模拟污染物对薄膜的光催化活性和稳定性进行了测定,采用电化学技术和向溶液中加入活性物种捕获剂的方法对薄膜光电催化降解机理进行了探索。结果表明:最佳工艺下制备的Ag@Ag Br/Ni膜电极是由表面沉积纳米Ag的纳米晶Ag Br颗粒构成的薄膜,具有显著的表面等离子共振效应。薄膜具有优异的光电催化活性和良好的催化稳定性,在最佳负偏压和可见光照射下反应12 min,薄膜光电催化罗丹明B(c=5 mg·L~(-1))的降解率是多孔Ti O2(P25)/ITO纳米薄膜的10.2倍。相对于未加偏压的光催化,降解率提高了2.0倍;在保持薄膜光催化活性基本不变的前提下可循环使用5次。电极表面纳米Ag粒子的等离子体共振对于光阴极反应(导带反应)的活化作用是光电催化活性提高的重要原因。提出了负偏压下Ag@Ag Br/Ni表面等离子体薄膜光电催化降解罗丹明B的反应机理。     

高效Ag@AgBr等离子体光催化剂的制备及可见光活性研究

采用水热法和光致还原法制备了具有等离子体共振效应的Ag@AgBr可见光催化剂,利用XRD,SEM,EDX,DRS和XPS等手段对产物的结构和性能进行表征,并研究了催化剂在可见光下对罗丹明B(RhB)的光催化降解性能,考察了催化剂的循环使用及捕获剂对Ag@AgBr光催化性能的影响.结果表明:贵金属Ag纳米粒子的表面等离子体共振效应可显著增强Ag@AgBr对可见光的吸收;催化剂对罗丹明B具有较高的可见光降解活性和稳定性,在可见光下照射90 min,对罗丹明B的降解率达95%以上,光催化剂循环使用5次仍具有良好的光催化降解活性;淬灭实验表明在Ag@AgBr降解罗丹明B过程中,吸附在催化剂表面的h+、·OH、O2·-是主要的活性物种.     

BiPO4@Ag3PO4核/壳异质结的制备及光催化性能

采用简单的水热法结合离子交换法制备了BiPO4@Ag3PO4核/壳异质结光催化剂,采用场发射扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)、紫外-可见漫反射光谱仪(DRS)和X射线光电子能谱仪(XPS)等对催化剂的形貌、组成、晶型和光物理性质等进行了研究,用罗丹明B(RhB)为模拟水体中有机污染物分别在可见光和模拟太阳光照条件下对催化剂的催化活性进行了测试.结果表明,负载Ag3PO4的BiPO4微米棒具有较高的可见光响应,其核/壳异质结结构有利于光生电子-空穴对的有效分离和提高对RhB的光催化降解效率,在可见光和模拟太阳光照射条件下分别在60和40 min可使RhB完全脱色降解.活性物种检测实验结果证明,该催化剂在污染物降解过程中主要的机理是光生空穴的直接氧化.     

Bi5O7I/聚苯胺复合光催化剂的制备及光催化活性

首先采用化学氧化聚合法合成聚苯胺(PANI),再采用溶剂热法制备了Bi_5O_7I/PANI复合材料,并采用X射线衍射、傅里叶变换红外光谱、场发射扫描电镜、紫外-可见漫反射光谱和荧光光谱等对所制备材料进行了表征,考察了复合材料在可见光光照条件下降解罗丹明B(RhB)的催化性能。结果表明当负载PANI后,Bi_5O_7I/PANI的复合材料都表现出优异的光催化性能。当PANI负载量在5%(w/w)时,催化效率最佳。在60 min内,其降解RhB的速率常数为Bi_5O_7I的3.9倍。捕获实验表明超氧自由基和空穴是该过程的主要活性物种。Bi_5O_7I/PANI具有优异光催化性能的原因主要在于,负载的PANI扩展了可见光吸收范围并增强了可见光吸收强度,而且PANI和Bi_5O_7I匹配的能级结构抑制了光生电子-空穴的复合效率。     

可见光驱动Ag3PO4催化降解罗丹明B和甲基橙

采用简易离子交换法制备可见光驱动Ag3PO4光催化剂.通过X射线衍射、场发射扫描电子显微镜、N2吸附-脱附、紫外-可见漫反射光谱及傅里叶变换红外光谱对所制备的Ag3PO4催化剂进行表征.结果表明,在可见光照射下,Ag3PO4催化剂对罗丹明B降解表现出优越的光催化活性,但对甲基橙的降解活性低,这归因于Ag3PO4催化剂对甲基橙分子吸附量低.可见光照Ag3PO4反应体系中,空穴和超氧自由基共同发挥作用导致罗丹明B和甲基橙光催化降解.在罗丹明B的协助作用下,Ag3PO4催化剂对甲基橙的可见光催化降解活性大大增强,这是由于罗丹明B的存在可产生更多的超氧自由基,从而使甲基橙进一步降解.     

负偏压下（Ni-Mo）/TiO2膜电极光电催化降解罗丹明B的性能和机理

用复合电沉积方法制备了(Ni-Mo)/TiO2薄膜电极,以扫描电子显微镜(SEM)、X射线衍射(XRD)、拉曼光谱(Raman Spectra)和紫外-可见漫反射光谱(DRS)对薄膜的表面形貌、晶相结构和光谱特性进行了表征,在负偏压和可见光作用下,以罗丹明B为模拟污染物研究了薄膜的光电催化性能.采用电化学技术和向溶液中加入活性物种捕获剂的方法对薄膜光电催化降解机理进行了探索.结果表明:(Ni-Mo)/TiO2薄膜是由粒径为50～100 nm的TiO2纳米粒子相和纳米晶Ni-Mo固溶体相构成的复合薄膜.薄膜具有较高的光电催化活性,在-0.4 V偏压和可见光照射下反应60 min,复合薄膜光电催化罗丹明B(c=5 mg/L)的降解率是多孔TiO2(P25)/ITO纳米薄膜的1.56倍.复合薄膜电极中Ni-Mo纳米晶合金对溶解氧和激发电子还原反应的催化作用是光电催化降解活性提高的重要原因.通过调节外加偏压,可以控制电极溶液界面间染料与活性氧化物种的存在形式及其相互作用,是研究可见光催化降解反应历程的有效方法.在负偏压和可见光作用下,羟基自由基和染料正离子自由基对染料的光电催化降解有决定性作用.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.