Oxidative Coupling of Methane over Na-W-Mn/SiO2 Catalysts at Elevated Pressures

Na-Mn-W/SiO2 catalysts were studied for the oxidative coupling of methane (OCM) in a micro fixed bed reactor made of stainless steel reactor at elevated pressures. The effect of operating conditions, such as GHSV, pressure, temperature and CH4/O2 ratio on the catalytic performance of OCM was investigated. The C2+ selectivity of 80.3% was obtained at a CH4 conversion of 16.1% at 750℃,1.5× 105h-1 GHSV, and 0.6 MPa. Also, there is a small output of C3 and C4 hydrocarbons in the tail gas. The results show that unfavorable effects due to elevated pressure can be overcome by increasing GHSV, and the OCM reaction is strongly dependent on the operating conditions at elevated pressures,particularly GHSV and the CH4/O2 ratio.     

Experimental investigation of fluidized-bed reactor performance for oxidative coupling of methane

Performance of the oxidative coupling of methane in fluidized-bed reactor was experimentally investigated using Mn-Na2WO4/SiO2,La2O3/CaO and La2O3-SrO/CaO catalysts.These catalysts were found to be stable,especially Mn-Na2WO4/SiO2 catalyst.The effect of sodium content of this catalyst was analyzed and the challenge of catalyst agglomeration was addressed using proper catalyst composition of 2%Mn2.2%Na2WO4/SiO2.For other two catalysts,the effect of Lanthanum-Strontium content was analyzed and 10%La2O 3-20%SrO/CaO catalyst was found to provide higher ethylene yield than La2O3/CaO catalyst.Furthermore,the effect of operating parameters such as temperature and methane to oxygen ratio were also reviewed.The highest ethylene and ethane (C2) yield was achieved with the lowest methane to oxygen ratio around 2.40.5% selectivity to ethylene and ethane and 41% methane conversion were achieved over La2O3-SrO/CaO catalyst while over Mn-Na2WO4 /SiO2 catalyst,40% and 48% were recorded,respectively.Moreover,the consecutive effects of nitrogen dilution,ethylene to ethane production ratio and other performance indicators on the down-stream process units were qualitatively discussed and Mn-Na2WO4/SiO2 catalyst showed a better performance in the reactor and process scale analysis.     

Product oriented oxidative bromination of methane over Rh/SiO2 catalysts

Rh/SiO2 was prepared for the oxidative bromination of methane. The catalyst was prepared by calcination at different temperatures and for different times to obtain catalysts with different specific surface areas for the purposes of producing either CH3Br or CH3Br and CO. It was found that the catalyst having a low specific surface area (calcined at relatively high temperature) favors the selective oxidation of methane to prepare CH3Br, while the catalyst having a high specific surface area favors the deeper partial oxidation of methane, which is good for CH3Br and CO preparation. The 650 h on stream life-time test revealed that the catalytic performance of the 0.4Rh/SiO2--900-10 catalyst was excellent. Both methane conversion and CH3Br selectivity kept increasing trends during the life-time test. No matter how serious was the Rh leaching during the reaction, the 0.4Rh/SiO2--900-10 catalyst did not deactivate at all.     

Product oriented oxidative bromination of methane over Rh/SiO_2 catalysts

Rh/SiO2 was prepared for the oxidative bromination of methane. The catalyst was prepared by calcination at different temperatures and for different times to obtain catalysts with different specific surface areas for the purposes of producing either CH3Br or CH3Br and CO. It was found that the catalyst having a low specific surface area (calcined at relatively high temperature) favors the selective oxidation of methane to prepare CH3Br, while the catalyst having a high specific surface area favors the deeper partial oxidation of methane, which is good for CH3Br and CO preparation.The 650 h on stream life-time test revealed that the catalytic performance of the 0.4Rh/SiO2-900-10 catalyst was excellent.Both methane conversion and CH3Br selectivity kept increasing trends during the life-time test.No matter how serious was the Rh leaching during the reaction,the 0.4Rh/SiO2-900-10 catalyst did not deactivate at all.     

Simulations on the thermal decomposition of a poly(dimethylsiloxane) polymer using the ReaxFF reactive force field

To investigate the failure of the poly(dimethylsiloxane) polymer (PDMS) at high temperatures and pressures and in the presence of various additives, we have expanded the ReaxFF reactive force field to describe carbon-silicon systems. From molecular dynamics (MD) simulations using ReaxFF we find initial thermal decomposition products of PDMS to be CH(3) radical and the associated polymer radical, indicating that decomposition and subsequent cross-linking of the polymer is initiated by Si-C bond cleavage, in agreement with experimental observations. Secondary reactions involving these CH(3) radicals lead primarily to formation of methane. We studied temperature and pressure dependence of PDMS decomposition by following the rate of production of methane in the ReaxFF MD simulations. We tracked the temperature dependency of the methane production to extract Arrhenius parameters for the failure modes of PDMS. Furthermore, we found that at increased pressures the rate of PDMS decomposition drops considerably, leading to the formation of fewer CH(3) radicals and methane molecules. Finally, we studied the influence of various additives on PDMS stability. We found that the addition of water or a SiO(2) slab has no direct effect on the short-term stability of PDMS, but addition of reactive species such as ozone leads to significantly lower PDMS decomposition temperature. The addition of nitrogen monoxide does not significantly alter the degradation temperature but does retard the initial production of methane and C(2) hydrocarbons until the nitrogen monoxide is depleted. These results, and their good agreement with available experimental data, demonstrate that ReaxFF provides a useful computational tool for studying the chemical stability of polymers.     

担载型钌催化剂吸附CO性能的原位红外研究

用原位红外研究了ＣＯ的吸附与脱附，ＣＯ／Ｈ２的共吸附及反应，考察了焙烧温度对Ｒｕ／Ａｌ２Ｏ３及Ｒｕ／ＳｉＯ２催化剂的影响，结果表明，经不同温度焙烧的催化剂样品，其吸附性能有很大差别。随着焙烧温度的升高，金属－载体相互作用增强，导致ＣＯ吸附量减少。Ｒｕ／Ａｌ２Ｏ３吸附的ＣＯ较稳定，而Ｒｕ／ＳｉＯ２吸附的ＣＯ在高温易脱附。各不同ＣＯ吸会态间、多重态更易发生反应。在未焙烧的Ｒｕ／ＳｉＯ２低ＣＯ／Ｈ２反应     

Breakthrough in the direct conversion of methane into c1-oxygenates

The partial oxidation of methane to CH3OH and HCHO (C1-oxygenates) was evaluated over a low surface area V2O5/SiO2 catalyst. The introduction of low amounts of NO (0-2.92% vol) to the reaction feed strongly enhanced both the conversion of methane and selectivity to C1-oxygenates. In the presence of NO, both the reaction temperature and the CH4/O2 ratio affected selectivity to CH3OH and HCHO. Selectivity values of C1-oxygenates as high as 40% at a methane conversion close to 40% were obtained.     

Ni/SiO2催化剂上甲烷催化裂解制氢

研究了固定床反应器上甲烷在Ni/SiO2催化剂上的裂解反应，并分别用O2、H2O进行催化剂失活/活化循环实验，并对催化剂用XRD进行分析。结果表明,Ni/SiO2催化剂具有良好的催化性能,甲烷转化率～40%，并能在150 min的时间内保持其活性，无论是用空气氧化还是水蒸气汽化，都能有效地活化已失活的催化剂。XRD实验显示，多次裂解－再生循环过程，对催化剂结构没有明显破坏。     

碱金属和氯离子对Mn_2O_3－Na_2WO_4／SiO_2催化剂甲烷氧化偶联反

本文考察了碱金属和氯离子对Ｍｎ２Ｏ３－Ｎａ２ＷＯ４／ＳｉＯ２催化剂甲烷氧化偶联反应性能的影响，结果表明，只有在氯离子和碱金属的共同作用下才能有效地提高Ｃ２烃的收率及其选择性．催化剂经ＮａＣｌ改性后，Ｃ２烃收率为２２％，并可获较高的烯烷比．在考察范围内增加接触时间（Ｗ／Ｆ），催化剂选择性保持不变，但乙烯的选择性呈上升趋势．钠盐Ｎａ２ＷＯ４、Ｎａ４Ｐ２Ｏ７、Ｎａ２ＳＯ４、Ｎａ２ＣＯ３及Ｎａ２Ｂ４Ｏ７对稳定催化剂的贡献按上述顺序逐渐减小．对ＮａＣｌ－Ｍｎ２Ｏ３－Ｎａ２ＷＯ４／ＳｉＯ２催化剂进行了稳定性考察，使用ＸＰＳ、ＸＲＤ和红外光谱对经历不同反应时间的催化剂进行了表征．     

COx-Free Hydrogen and Carbon Nanofibers Produced from Direct Decomposition of Methane on Nickel-Based Catalysts

Direct decomposition of methane was carried out using a fixed-bed reactor at 700℃for the production of COx-free hydrogen and carbon nanofibers. The catalytic performance of NiO-M/SiO2 catalysts (where M=AgO, CoO, CuO, FeO, MnOx and MoO) in methane decomposition was investigated. The experimental results indicate that among the tested catalysts, NiO/SiO2 promoted with CuO give the highest hydrogen yield. In addition, the examination of the most suitable catalyst support, including Al2O3, CeO2, La2O3, SiO2, and TiO2, shows that the decomposition of methane over NiO-CuO favors SiO2 support. Furthermore, the optimum ratio of NiO to CuO on SiO2 support for methane decomposition was determined. The experimental results show that the optimum weight ratio of NiO to CuO fell at 8:2 (w/w) since the highest yield of hydrogen was obtained over this catalyst.     

铁助剂对Rh-Mn-Li/SiO2催化剂表面上的CO脱附和CO加氢行为的影响

 采用一氧化碳程序升温脱附（CO－TPD）和吸附的一氧化碳加氢程序升温表面反应（TPSR）考察了Fe助剂对Rh基催化剂上CO的脱附行为及吸附CO的加氢行为的影响．CO－TPD实验表明，在Rh／SiO2催化剂上CO有三个脱附峰．在Rh－Mn－Li／SiO2中加入0．05％Fe后，高温脱附CO比Rh／SiO2催化剂上相应的CO量大．增加Fe的负载量，CO的脱附量减少．TPSR实验中，CO加氢反应的主要产物是甲烷．不同组分的催化剂上甲烷的生成温度有如下顺序：Rh／SiO2（482K）＜Rh－Mn－Li／SiO2（489K）＜Rh－Fe／SiO2（494K）＜Rh－Mn－Li－Fe／SiO2（501K）．甲烷峰的产生伴随着CO（s）高温脱附峰的消失，说明甲烷是由强吸附的CO加氢生成的．     

Na-W-Mn/SiO2催化剂活化甲烷的研究Ⅱ.活性氧物种

制备了不同Ｎａ、Ｗ、Ｍｎ组分的Ｎａ－Ｗ－Ｍｎ／ＳｉＯ２催化剂,并进行了Ｏ２程序升温脱附（Ｏ２－ＴＰＤ）和不同温度下Ｎａ－Ｗ－Ｍｎ／ＳｉＯ２催化剂的ＣＨ４脉冲反应（ＣＨ４－ＰＲ）。研究结果表明,Ｎａ－Ｗ－Ｍｎ／ＳｉＯ２催化剂活化甲烷的活笥氧物种是Ｗ和Ｍｎ提供的、高温下易于流动的表面晶格氧（Ｏ＾２－）。Ｎａ和Ｏ＾２－的活泼性具有重要的促进作用,它可以极化Ｗ、Ｍn的金属一氧键,促进Ｏ＾２－的流动性。Ｎａ     

A core-shell magnetic mesoporous silica sorbent for organic targets with high extraction performance and anti-interference ability

C(18)-functionalized mesoporous silica shell was successfully fabricated on the surface of an Fe(3)O(4)/SiO(2) core to obtain an Fe(3)O(4)/SiO(2)/SiO(2)-C(18) magnetic microsphere. The microsphere exhibited high extraction efficiency to organic targets and strong anti-interference ability to natural organic matter. It could be easily isolated from water solution after extraction.     

Mechanistic study of partial oxidation of methane to syngas using in situ time-resolved FTIR and microprobe Raman spectroscopies

In situ time-resolved Fourier transform infrared (FTIR) and microprobe Raman spectroscopies were used to characterize the reaction mechanisms of the partial oxidation of methane to syngas over SiO(2)- and gamma-Al(2)O(3)-supported rhodium and ruthenium catalysts. The interaction of both pure methane and a methane/oxygen mixture at a stoichiometric feed ratio with an oxygen-rich catalyst surface led to the formation of CO2 and H(2)O as the primary products. For the H(2)-pretreated samples, the reaction mechanisms with the catalysts differ. Only Rh/SiO(2) is capable of catalyzing the direct oxidation of methane to syngas, while syngas formation over Rh/gamma-Al(2)O(3), Ru/SiO(2), and Ru/gamma-Al(2)O(3) can be achieved mainly via a combustion-reforming scheme. The significant difference in the mechanisms for partial oxidation of methane to syngas over the catalysts can be correlated to the differences in the concentration of oxygen species (O(2-)) on the catalyst surface during the reaction, mainly due to the difference in the nature of the metals and supports.     

负载型钼基催化剂上甲烷,乙烷无氧芳构化反应研究

研究了不同载体钼基催化剂上甲烷，乙烷的无氧芳构化反应。在所采用的载体中，ＨＺＳＭ－５具有最佳性能，对甲烷的芳构化反应，Ｍｏ／ＨＺＳＭ－５催化剂表现出较高的活性和芳烃选择性；而Ｍｏ／Ａｌ２Ｏ３或Ｍｏ／ＳｉＯ２催化剂则相对较差。对于乙烷的反应，钼物种的存在更有利于甲烷或乙烯的生成，芳烃选择性相对较低。钼物种较强的断键能力可能是使甲烷Ｃ－Ｈ键活化的原因。     

Na-W-Mn/SiO_2催化剂中Na对甲烷氧化偶联制乙烯的作用(英文)

采用常规浸渍法制备了一系列Na（wt％）含量不同的Na－W－Mn／SiO_2催化剂,在流动态微型固定床常压反应装置上评价了这些催化剂的甲烷氧化偶联（OCM）制乙烯催化反应性能,并进行了XPS、XRD表征。实验结果表明,Na含量为0．39wt％－2．34Wt％的Na－W－Mn／SiO_2催化剂具有好的甲烷氧化偶联制乙烯性能,此时Mn以对反应有利的晶相存在,同时由于Na的表面富集,引起W、Mn向催化剂表面发生迁移。由此可见,在Na－W－Mn／SiO_2催化剂中,Na是甲烷转化和乙烯生成不可缺少的活性组分之一。     

In-Situ FT-IR Investigation Methane to Syngas over of Partial Oxidation of Rh/SiO2 Catalyst

Partial oxidation of methane to syngas （POM） over Rh/SiO2 catalyst was investigated using in-situ FT-IR. When methane interacted with 1.0wt%Rh/SiO2 catalyst, it was dissociated to adsorbed hydrogen and CHx species. The adsorbed hydrogen atoms were transferred to SiO2 surface by ＂spill-over＂ and reacted with lattice oxygen to form surface -OH species. POM mechanism was investigated over Rh/SiO2 catalyst using in-situ FT-IR. It was found that CO2 was formed before CO could be detected when CH4 and O2 were introduced over the preoxidized Rh/SiO2 catalyst, whereas CO was detected before CO2 was formed over the prereduced Rh/SiO2 catalyst.     

Dual-Bed Catalytic System for Direct Conversion of Methane to Liquid Hydrocarbons

A dual-bed catalytic system is proposed for the direct conversion of methane to liquid hydrocarbons. In this system, methane is converted in the first stage to oxidative coupling of methane (OCM) products by selective catalytic oxidation with oxygen over La-supported MgO catalyst. The second bed, comprising of the HZSM-5 zeolite catalyst, is used for the oligomerization of OCM light hydrocarbon products to liquid hydrocarbons. The effects of temperature (650-800℃), methane to oxygen ratio (4 10), and SiO2/Al2O3 ratio of the HZSM-5 zeolite catalyst on the process are studied. At higher reaction temperatures, there is considerable dealumination of HZSM-5, and thus its catalytic performance is reduced. The acidity of HZSM-5 in the second bed is responsible for the oligomerization reaction that leads to the formation of liquid hydrocarbons. The activities of the oligomerization sites were unequivocally affected by the SiO2/Al2O3 ratio. The relation between the acidity and the activity of HZSM-5 is studied by means of TPD-NH:j techniques. The rise in oxygen concentration is not beneficial for the C5 selectivity, where the combustion reaction of intermediate hydrocarbon products that leads to the formation of carbon oxide (CO CO2) products is more dominant than the oligomerization reaction. The dual-bed catalytie system is highly potential for directly converting methane to liquid fuels.     

甲烷氧化偶联Mn_2O_3-Na_2WO_4/SiO_2催化剂——Ⅱ.表面氧种和结构

本文用XPS详细考察了Mn_2O_3-Na_2WO_4/SiO-2催化剂的表面氧种,提出了该催化剂表面活性相在SiO_2表面分散的一种可能的表面结构模型。 实验部分详见另文,这里需要指出。所有催化剂样品在XPS分析前,均经在能谱仪预处理室(～10~(-3)Pa)和超高真空测试室(基础真空6.7×10~(-8)Pa)递次的450C和700C原位加热处理,以使在大气中吸附的水分和气体脱附。各元素的特征谱峰由联机计算机以多道模式同时录取(通能50eV),并累加1 h以获取高信噪比数据。Ols峰的解迭用联机计算机以高斯函数拟合,为考察该解迭结果的可靠性,曾对1.9wt％Mn_2O_3-5wt％Na_2WO_4/SiO_2催化利的     

高性能甲烷催化燃烧催化剂的制备及其在天然气催化燃烧热水器上的应用

 以镧改性的Ce-Zr-O固溶体储氧材料和钇、锆改性的氧化铝(YSZ-Al2O3)的混合物为载体,浸渍活性组分Co3O4+Fe2O3+MnO2,以蜂窝状堇青石陶瓷材料为基体,制备了甲烷催化燃烧催化剂,考察了该催化剂老化前后的活性,并将其用于强鼓式家用天然气催化燃烧热水器. 结果表明,该催化剂具有很高的活性和稳定性. 使用此催化剂的天然气催化燃烧热水器的热效率达到101.1%, 同时烟气中CO和NOx污染物的排放浓度分别为0.014%和0.003%, 该热水器具有高效节能和环境友好双重优点.