锂离子电池负极材料Li_(4-x)K_xTi_5O_(12)结构和电化学性能

采用固相反应的方法制备了尖晶石型Li4Ti5O12和K掺杂Li4-xKxTi5O12(x=0.02,0.04,0.06)。通过XRD、SEM、BET等对制备材料进行了分析。结果表明,K掺杂没有影响立方尖晶石型Li4Ti5O12的合成,同时也没有改变Li4Ti5O12的电化学反应过程。K掺杂Li4-xKxTi5O12具有比Li4Ti5O12小的颗粒粒径和比Li4Ti5O12大的比表面积、孔容积。适量的K掺杂能够明显改善Li4Ti5O12的电化学性能,尤其是倍率性能,但是过多的K掺杂却不利于材料电化学性能的提高。研究表明,Li3.96K0.04Ti5O12体现了相对较好的倍率性能和循环稳定性。0.5C下,首次放电比容量为161mAh·g-1,3.0和5.0C下,容量保持分别为138和121mAh·g-1。3.0C下,200次循环后容量保持为137mAh·g-1。     

三维有序大孔锂离子筛的制备及其交换性能研究

由110 nm聚苯乙烯(PS)微球组装晶体胶体模板,并用此模板合成三维有序大孔(3-dimensionally ordered macroporous,3DOM)锂离子筛前驱体Li4Ti5O12,用1.0 mol.L-1的盐酸改型制得锂离子筛H4Ti5O12(LiTi-H)。用XRD、SEM、饱和交换容量、pH滴定曲线等表征了材料的形貌、结构和离子交换性能。同时测定了25℃时LiTi-H在0.05 mol.L-1Li+体系吸附锂的动力学数据,并采用吸附动力学Bangham方程和Elovich方程关联离子筛LiTi-H对Li+的离子交换动力学数据。结果表明:PS胶体晶体模板和3DOMLi4Ti5O12锂离子筛前驱体均排列规则有序,大孔直径约90 nm,Li4Ti5O12为尖晶石结构;3DOM Li4Ti5O12酸稳定性好,锂离子筛LiTi-H对Li+具有较高的选择性,对Li+的饱和交换容量达56.70 mg(Li+).g-1;动力学模型用Elovich模型关联较好,离子筛对Li+的离子交换动力学方程是Q=-26.510 4+11.977 4lnt(25℃)。     

纯相Li4Ti5O12水热合成及其电化学性能

以纳米级锐钛矿型二氧化钛(TiO2)和氢氧化锂(LiOH)为原料,利用水热法合成了尖晶石型Li4Ti5O12材料,并研究了LiOH浓度、水热反应时间及热处理温度对Li4Ti5O12样品结构和电化学性能的影响,分析了Li4Ti5O12的形成过程.采用X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)分析样品材料结构,观察材料形貌.结果表明,LiOH浓度0.2 mol.L-1、水热反应时间12 h及煅烧温度700℃可得到纯相尖晶石型Li4Ti5O12,该样品1C倍率放电比容量为146.3 mAh.g-1,40C高倍率其放电比容量仍有101.3 mAh.g-1.     

锂离子电池负极材料Li4Ti5O12

Li4Ti5O12具有充放电循环性能好、电压平台平稳、安全性高、价格低、环境友好、易于制备等优点,在锂离子电池负极材料中得到广泛研究.本文基于国内外近期的研究进展,综述了制备Li4Ti5O12的方法,着重介绍了固相、溶胶一凝胶、熔盐、燃烧、喷雾、水/溶剂热等几种主要的合成方法,并针对Li4Ti5O12电导率低的缺点,详...     

Preparation of Li_4Ti_5O_(12) submicrospheres and their application as anode materials of rechargeable lithium-ion batteries

We report on the preparation of spinel Li4Ti5O12 submicrospheres and their application as anode materials of rechargeable lithium-ion batteries. The spinel Li4Ti5O12 submicrospheres are synthesized with three steps of the hydrolysis of TiCl4 to form rutile TiO2, the hydrothermal treatment of rutile TiO2 with LiOH to prepare an intermediate phase of LiTi2O4+δ, and the calcinations of LiTi2O4+δ to obtain spinel Li4Ti5O12. The as-prepared products are investigated by X-ray powder diffraction (XRD), scanning el...     

高倍率尖晶石型Li4Ti5O12/TiN锂离子电池负极材料的合成及其电化学性能

以乙酰丙酮(ACAC)螯合剂、聚乙二醇(PEG)为分散剂,采用溶胶-凝胶法合成了尖晶石型Li4Ti5O12/TiN材料.考察了TiN膜对尖晶石型Li4Ti5O12锂离子电池负极材料电化学性能的影响.利用X射线光电子能谱(XPS)对Li4Ti5O12表面的TiN膜进行了分析.X射线衍射(XRD)和扫描电子显微镜(SEM)分析表明,Li4Ti5O12/TiN材料为结晶良好的亚微米纯相尖晶石型钛酸锂.电化学性能测试表明,该材料的首次放电比容量为173.0mAh·g-1,并且具有良好的循环性能,以0.2C、1C、2C、5C倍率放电进行测试,10次循环后比容量分别为170.6、147.6、135.6、111.0 mAh·g-1,较之表面无TiN膜的钛酸锂材料表现出更好的倍率特性.循环伏安曲线(CV),交流阻抗图谱(EIS)进一步论证了TiN膜改善了尖晶石型Li4Ti5O12锂离子电池负极材料的电化学性能.     

锂离子电池负极材料Li4Ti5O12的半固相法制备及碳包覆改性

由半固相法制得锂离子电池负极材料Li4Ti5O12,并研究了Li4Ti5O12的碳包覆改性.采用XRD、SEM、TEM以及HRTEM观察和分析产物的相结构与形貌.采用恒流充放电、循环伏安法和交流阻抗技术测试了材料的电化学性质.结果表明,Li4Ti5O12因颗粒团聚电化学性能严重下降,该电极在0.1C和0.5C首周期放电容量分别为121.7和87.6 mAh·g-1;碳包覆Li4Ti5O12/C材料呈球形分布,能抑制颗粒团聚,该电极倍率<0.5C时的放电比容量大于180 mAh·g-1,超过Li4Ti5O12的理论放电比容量(175 mAh·g-1);在1C、5C和10C倍率下,其容量仍保持在136、79.9和58.3 mAh·g-1,碳包覆改性材料具有优异的循环寿命和高倍率性能.     

锂钛复合氧化物锂离子电池负极材料的研究

采用 3种化学方法合成锂钛复合氧化物 .应用X -射线衍射分析对其结构进行表征以及电化学性能测试 ,结果表明 :由Li2 CO3、TiO2 高温合成的锂钛复合氧化物为尖晶石结构的Li4Ti5 O12 .Li4Ti5 O12 电极在 1 .5V左右有一放电平台 ,充放电可逆性良好 ,即充电电压平台与此接近 ,且电极的比容量较大 ,循环性能良好 .以 0 .30mA·cm- 2 充放电时 ,首次放电容量可达 30 0mAh·g- 1,可逆比容量为 1 0 0mAh·g- 1,经多次充放电循环后 ,其结构仍保持稳定性 .试验电池测试表明 ,Li4Ti5 O12 可选作Li4Ti5 O12 /LiCoO2 锂离子电池的负极材料 .     

Li_4Ti_5O_(12)亚微米球的制备及其在锂离子电池中的应用

主要合成了具有尖晶石结构的Li4Ti5O12亚微米球电极材料,并研究了其作为锂离子电池负极材料的电化学性能.材料的制备分为三个步骤:TiCl4水解得到金红石相的TiO2,然后将得到的TiO2与LiOH进行水热反应得到中间相LiTi2O4+δ,最后将中间相高温煅烧得到尖晶石结构的Li4Ti5O12.采用XRD、SEM和TEM等手段对材料的结构和形貌进行表征.结果表明,尖晶石相的Li4Ti5O12负极材料具有分级结构,是由20～30nm的小颗粒堆积成约为200～300nm的亚微米球.将制备的Li4Ti5O12材料进行恒电流充放电测试表明,材料具有优异的倍率放电性能和较好的循环可逆性;在1C充放电时,首次放电比容量达到174.3mAh/g,在第5～50次循环过程中仅有微小的不可逆容量损失.采用循环伏安法测得Li+的扩散系数为1.03×10-7cm2/s.研究表明合成的Li4Ti5O12亚微米球在高效可充电锂离子电池中具有良好的应用前景.     

三维连续结构Li4Ti5O12/石墨烯纳米复合材料：制备和其锂离子电池超长循环性能

利用具有三维连续纳米孔结构的热剥离石墨烯为骨架制备Li4Ti5O12/石墨烯纳米复合材料。通过乙醇挥发法在热剥离石墨烯的纳米孔道内引入前驱物,进一步高温热处理,在热剥离石墨烯的孔道内原位形成Li4Ti5O12纳米粒子。利用复合材料作为锂离子电池电极材料。电化学反应过程中,热剥离石墨烯的三维连续结构确保了Li4Ti5O12纳米粒子与石墨烯在长循环过程中的有效接触。因此,复合材料表现出优异的循环稳定性。在5C下,5 000次循环后,其容量保持率高达94%。     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

NaBO2-NaCl-Na2CO3, NaBO2- Na2CO3-NaMoO4, NaBO2- Na2CO3-NaWO4, and NaBO2-NaCl-Na2WO4 ternary systems

The phase diagrams of the NaBO₂-NaCl-Na₂CO₃, NaBO₂-Na₂CO₃-Na₂MoO₄, NaBO₂- Na₂CO₃-Na₂WO₄, and NaBO₂-NaCl-Na₂WO₄ ternary systems were studied by a calculation-experimental method and differential thermal analysis. The coordinates of ternary eutectics were determined: E ₁: 612°C, 16 mol % NaBO₂, 42 mol % NaCl, and 42 mol % Na₂CO₃; E ₂: 568°C, 12 mol % NaBO₂, 28 mol % Na₂CO₃, and 60 mol % Na₂MoO₄; E ₃: 575°C, 12 mol % NaBO₂, 32 mol % Na₂CO₃, and 56 mol % Na₂WO₄; E ₄: 628°C, 8 mol % NaBO₂, 20 mol % NaCl, and 72 mol % Na₂WO₄; and E ₅: 655°C, 9 mol % NaBO₂, 53 mol % NaCl, and 38 mol % Na₂WO₄.     

Theoretical study of polyoxide clusters B20O30, Al20O30, V20O50, Si20O30H20, and Si20O30F20

The structural, electronic, and vibrational characteristics and energies of the isolated polyoxide clusters B₂₀O₃₀, Al₂₀O₃₀, V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀ and their complexes with the H⁻ ion and ammonia complexes Al₂₀O₃₀ · nNH₃ have been calculated by the density functional theory B3LYP method with different basis sets. The computation results show that the symmetric closo structure I _h with oxygen bridges located above the centers of the faces of an empty [M₂₀] dodecahedron is more favorable for V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀. For B₂₀O₃₀, the cage closo isomer is also more favorable than the other isomers, but its structure is severely distorted as compared to a dodecahedron and has a symmetry close to C ₃ . For Al₂₀O₃₀, the I _h structure corresponds to a high-lying local minimum of the potential energy surface. For Al₂₀O₃₀, a set of unusual puckshaped isomers of symmetry C _i , with different numbers of four-coordinate atoms ^IVAl and three-coordinate atoms ^IIIO, was localized; these structures are more than 90 kcal/mol more favorable than the dodecahedron I _h . The most favorable isomer of Al₂₀O₃₀ contains twelve four-coordinate atoms ^IVAl and four five-coordinate atoms ^VAl. The energies of dissociation of the most favorable M₂₀O₃₀ clusters into the M₂O₃ (C _2v ) and M₄O₆ (T _d ) fragments and, in the case of Al₂₀O₃₀, also into the Al₈O₁₂ (O _h ) and Al₁₂O₁₈ (D _3d ) fragments, have been estimated. The conclusion has been drawn that these clusters can, in principle, exist and can be experimentally detected in the isolated state. Analogous calculations have been performed for ammonia complexes Al₂₀O₃₀ · nNH₃ with n varying from 1 to 20. The effect of solvation on the relative stability of the dodecahedral and puckshaped isomers of the Al₂₀O₃₀ cluster is observed. The isomers with ammonia molecules in their first coordination sphere become much closer to one another on the energy scale; however, the dodecahedron remains a considerably less favorable intermediate. Original Russian Text ? O.P. Charkin, N.M. Klimenko, D.O. Charkin, 2008, published in Zhurnal Neorganicheskoi Khimii, 2008, Vol. 53, No. 4, pp. 624–635.     

Structural chemistry of Sr3Cr2WO9, Ca3Cr2WO9, and Ba3Cr2WO9

We have studied the preparation and crystallographic structure of three perovskite-type compounds: Sr₃Cr₂WO₉, cubic, the lattice parameter of which is a = 7.812Å; Ca₃Cr₂WO₉, tetragonal, the lattice parameters of which are a = 5.408 Å and c = 7.635Å; and Ba₃Cr₂WO₉, hexagonal, the lattice parameters of which are a = 5.691 Å and c = 13.957Å. We have compared these three structures and shown the relationship between the dimensions of the alkaline-earth metal and the existence of the different structures.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.