铜–铬–锆合金光谱分析用标准物质的研制

以电解铜和铜–铬、铜–锆中间合金为原材料,通过真空熔炼和热锻加工工艺,研制了铜–铬–锆合金光谱分析用标准物质。将样品分成4组,每组85块后,采用金相检验和光电直读光谱仪进行均匀性、稳定性和定值分析。从样品中随机抽取15块进行均匀性检验,经F检验表明,在95%的置信区间范围内样品均匀性良好;稳定性考察12个月,结果表明在考察期间内样品稳定性良好;标准物质样品经国内3家具有分析资质的实验室进行协作定值,并评定了定值结果的不确定。铜–铬–锆合金标准物质样品中Cr,Zr元素的相对扩展不确定度分别为0.015%~0.036%,0.019%~0.033%(k=2)。该标准物质达到了国家标准物质的技术要求,可用于有关铜–铬–锆合金产品中铬、锆元素的方法校准和质量控制。     

铸造铝合金ZL205A中铜锰镉铁锆钛的连续测定

试样以氢氧化钠溶解,硝酸酸化,用原子吸收分光光度计进行铜、锰、镉、铁等量的测定;在0.15mol·L~(-1)硫酸介质中,以抗坏血酸还原铁、钛与吐温-80、邻氯苯基荧光酮(CPF)形成稳定的三元络合物,在6～8mol·L~(-1)的硝酸介质中,锆与偶氮胂Ⅲ形成稳定的络合物,用721型分光光度计进行钛和锆量的测定。 1 仪器与试剂 GFU-202B型双光束原子吸收分光光度计(北京分析仪器厂) 721型分光光度计(上海分析仪器厂) CPF:2×10~(-3)mol·L~(-1),称取CPF 0.71g,用硫酸(1 3)10ml和无水乙醇500ml溶解后,用水稀至1L棕色量瓶中。 2 仪器工作条件(见表)     

间接原子吸收分光光度法测定锆

研究了空气－乙炔火焰原子吸收光谱法间接测定微量锆的方法,在弱酸性溶液中钢与Ｎ－亚硝基苯胲（铜铁试剂）形成１：２络合物可被氯仿定量萃取,Ｚ ｒ（Ⅳ）定量置换Ｎ－亚硝基苯胲钢中的铜,原子吸收光谱法测铜间接测锆,特征浓度为 ０．０７ × １０－６ ｇ／ｍＬ／１％,线性范围为 ０～５ｍｇ／Ｌ,方法简便、快速、灵敏度高,选择性好,用于瓷釉和α－βＡｌ２Ｏ３中氧化锆的测定,结果满意。     

锆存在时铀中杂质元素的化学分离-ICP-AES法

采用磷酸三丁酯（TBP）－氢化煤油萃取油、过氧化氢掩蔽钛、磷酸氢二铵沉淀锆的方法，用ICP－AES法同时测定了锆存在在时铀中的铁、锰、铜、硅、铝、镍和钛7种杂质元素的含量。当测定范围在100μg/g-1000μg/g时，相对标准偏差＜9．0％，回收率为96％－109％。     

原子吸收法间接测定微量锆

间接原子吸收光谱法的研究受到人们的普遍重视,主要有利用杂多酸的“化学放大”效应间接测定磷、砷、锗;沉淀反应间接测定氯离子、硫酸根,化学干扰效应间接测定钛、铝及络合效应间接测定钒、硼、硝酸根等,但在间接测锆方面未见报道,本文用Mg-8-羟基喹啉(MgL_2)沉淀锆置换出定量的镁,通过测镁间接测锆,建立了空气-乙炔火焰原子吸收光谱法间接测定锆的新体系,方法的特征浓度为0.018mg/L/1%,较氧化亚氮乙炔火焰(10mg/L/1%)提高500倍,该方法灵敏、快速、体系稳定,经萃取分离除去干扰元素,用于实际样品中氧化锆的测定,结果满意.2 实验部分     

锆元素概念的形成和发展

1789年,普鲁士分析化学家克拉普罗特提出黄锆石中含有一种新土质,并将其命名为“锆土”,锆元素假说正式形成。随后,锆的原子重量的测定以及锆元素在元素表中位置的确定,促进了锆元素假说的发展。1914年,荷兰工程师勒利和汉布格首次制得纯度较高的金属锆,这使得锆元素假说得以证实,锆元素概念正式形成。从1924年至2020年,锆同位素的发现使人们对锆元素有了新认识,促使了现代锆元素概念的形成。锆元素概念的形成和发展的过程既是元素的发现史,也是化学思想和化学方法的演进史。     

阳离子交换树脂分离-电感耦合等离子体原子发射光谱法测定新锆合金中六种微量元素

新锆合金样品用硝酸和氢氟酸溶解,样品溶液经阳离子交换树脂使锆和铌与其他6种元素分离后,用电感耦合等离子体原子发射光谱仪测定2.0 mol·L-1硝酸洗脱液中铝、钡、铜、镍、钛和钒的含量.对分离锆和铌所用硝酸淋洗液的浓度、pH值、用量,载气流量等影响因素进行了试验.在优化的试验条件下,测得铝、钡、铜、镍、钛和钒的相对标准偏差(n=6)在3.0%～7.9%之间,回收率在93.8%～110.0%之间.     

催化动力学光度法测定痕量锆

研究了在弱酸性介质中，锆（Ⅳ）催化过氧化氢氧化铬蓝黑Ｒ这一新的指示反应及其动力学条件，建立了一种高灵敏、高选择性测定痕量锆的新方法，方法检出限为３．７４×１０－１１ｇ／ｍＬ，线性范围０～１．１μｇ／２５ｍＬＺｒ（Ⅳ）．用于合金钢中痕量锆的测定，结果满意．     

锆助剂对低温液相合成甲醇用铜铬硅催化剂性能的影响

考察了含锆的铜铬硅催化剂低温液相合成甲醇性能，并进行了BET、TPR-H2、TPD-H2、TPD-CO、XRD和XPS表征。结果表明，锆作为结构助剂及电子助剂对催化剂在低温液相合成甲醇反应中具有显著的促进作用，反应活性可提高32.25 ％。锆助剂能有效提高催化剂的比表面积，促进催化剂中铜铬组分的分散及表面富集。ZrO2加入在催化剂表面产生的Cu+与催化活性的改善密切相关，Zr4+、Cr3+、Cu+可形成复合中心，为价态的稳定性提供微环境，在H2活化及C O键的断裂等反应步骤中起重要作用。     

人工神经网络吸光光度法同时测定钛锆

在钛,锆-二溴羟基苯基荧光酮-CTMAB显色体系中,应用三层ANN—BP网络解析钛和锆的吸收光谱,不经分离吸光光度法同时测定钛和锆。钛和锆的表观摩尔吸光系数分别为ε_(547)=9.66×10~4,ε_(533)=1.80×10~5。同时测定合金钢中钛和锆,结果满意。使用改进的BP算法,避免了神经网络学习过程中可能产生的麻痹现象。提出了目标向量的简单变换方法及便于网络参数选择的收敛评价函数。     

Electrochemical stripping determination of traces of copper, lead, cadmium and zinc in zirconium metal and zirconium dioxide

Procedures have been developed for the determination of copper, lead, cadmium and zinc in zirconium metal and zirconium dioxide, at concentrations of 1 ppm or less. Zirconium metal was dissolved in suphuric acid, and zirconium dioxide decomposed under pressure with hydrofluoric acid. Sample solutions were prepared in dilute sulphuric acid. For the stripping determination, the sample solution was either mixed with a complexing tartrate base electrolyte or the pre-electrolysis was carried out in acid solution, with the acid solution being exchanged for a pure base electrolyte (e.g. an acetate buffer) for the stripping step. The stripping step was monitored by d.c., differential pulse and Kalousek commutator voltammetry and the three methods were compared. A stationary mercury-drop electrode can generally be used for all the methods, whereas a mercury-film electrode is suitable only for the d.c. voltammetric determination of copper, lead and cadmium, as pulse measurements with films are poorly reproducible and the electrodes are easily damaged. The relative standard deviation does not exceed 20%. Some samples contained relatively large amounts of copper, which is best separated by electrodeposition on a platinum electrode.     

The determination of zirconium in fluoride-containing solutions

In the recommended procedure the zirconium is first precipitated from solution as the insoluble barium fluozirconate. After separation, the precipitate is dissolved in a mixture of nitric and boric acids and the zirconium is then precipitated as its hydroxide. This precipitate is separated, dissolved in hydrochloric acid and this solution is evaporated to fumes of perchloric acid to remove completely fluoride ions. The zirconium content is then determined volumetrically by adding a slight excess of a standard solution of ethylenediaminetetra-acetic acid and back titrating with a standard iron solution at pH 2.3 using potassium benzohydroxamate as indicator and the photometric technique for end-point detection. This method is applicable to the determination of milligram amounts of zirconium in fluoride-containing nitric or hydrochloric acid solutions provided that the concentration of these acids is below 3N. It is also suitable for the determination of zirconium in the presence of any of the following elements - uranium, titanium, niobium, tantalum, molybdenum, tungsten, lead, iron, copper and tin.     

铜合金中铜的示波滴定—四苯硼钠法

本文报道了铜合金中铜的示波滴定方法。样品酸溶后，用抗坏血酸还的Ｃｕ＾２＋为Ｃｕ＾＋，加入过量的四苯硼钠，在ＰＨ５－６的ＨＡｃ－ＮａＡｃ缓冲溶液中，定量形成Ｃｕ－ＴＰＢ沉淀，过量的ＴＰＢ＾－，以Ｔｌ＾＋标准溶液进行示波滴定，铜合金中共存元素不干扰测定。铜的测定回收率９９．８％－１００．１％。进行了多种铜合金中铜含量的测定，结果令人满意。     

原子荧光光谱法测定铜合金中铋元素含量方法改进

基于原子荧光光谱法测定铋元素时检出限低、测定结果稳定且准确等优点,研究原子荧光光谱法测定铜合金中铋元素含量的方法。在标准系列中加入相近浓度的铜元素标准溶液,原子荧光光谱法测定铜合金中铋元素含量。称取0.1 g样品,加入10 mL硝酸溶解,10%硫脲-5%抗坏血酸溶液7.5 mL预处理样品。在20μg/L的铋标准溶液中加入6 mL浓度为1000μg/mL的铜元素标准溶液。结果表明:在0~20μg/L范围内,该方法线性关系良好,线性方程为I=138.1670c+43.8572,相关系数为0.9996,所测定的样品中铋元素含量的相对误差在-4.3%~7.7%之间,精密度在0.4%~4.7%之间。原子荧光光谱法可作为铜合金中铋元素含量测定的方法。     

电感耦合等离子体原子发射光谱法测定铜合金中锆量的不确定度评定

讨论了采用电感耦合等离子体发射光谱法测定铜合金中锆量分析结果不确定度产生的原因。建立了数学模型,对测量重复性,标准溶液,标准曲线变动,试液体积,试样称量,数字修约等引起的不确定分量进行评定,计算了合成标准不确定度和扩展不确定度,并给出铜合金中锆量测定结果的报告。评定结果表明:测量重复性,标准曲线线性回归引起的不确定度对总不确定度影响最大。所以在测定中应进行多次平行测定,特别注意标准曲线的校正和绘制校准曲线所用标准样品的选择。     

Na2EDTA反滴定法测定铜镍合金中的镍

采用Na2EDTA返滴定法测定铜镍合金中的镍含量, 用柠檬酸钠、硫代硫酸钠和酒石酸做掩蔽剂,丁二酮肟沉淀分离,以二甲酚橙为指示剂,加入过量的Na2EDTA,用氯化锌标准溶液返滴定。方法能很好地分离铜及其他杂质的干扰。试验方法用于测定铜镍合金中的镍含量,测定结果的相对标准偏差（RSD,n=9）为0.0456%～0.2409%,加标回收率为99.30%～101.10%如有残渣,过滤之后将残渣消解,用光谱测定不溶渣中的镍含量。能够满足日常样品的检测要求。     

X-ray fluorescence analysis of titanium alloys

An X-ray solution method is proposed for determining major amounts of Mo, Sn and Zr in Ti alloys. The method utilizes adjacent elements in the periodic table as internal standards and has been successfully applied to levels of 3-10% Sn, 11-40% Mo and 6-20% Zr. The procedure involves three steps: dissolving the sample with a suitable acid mixture; adding the suitable internal standard at the concentration levels experimentally found to give optimum accuracy and precision; analysing the resulting solution mixture by X-ray fluorescence. Antimony was found to be a suitable internal standard for its adjacent element tin at a concentration ratio of 3:1 Sb:Sn. Niobium was successfully used for both its adjacent elements, molybdenum and zirconium, at 2:1 concentration ratios, Nb:Mo and Nb:Zr. A number of elements non-adjacent to tin, molybdenum and zirconium (i.e., copper, bromine, titanium, bismuth and tantalum) were experimentally found unsuitable as internal standards. Concentration factors of the internal standard and the adjacent elements sought were found to affect significantly the precision of analysis.     

碱熔酸浸试样–碘量法测定铜冶炼白烟尘中的铜

建立碱熔酸浸试样–碘量法测定铜冶炼白烟尘中铜的方法。采用氢氧化钾–硝酸钾混合溶剂熔融试样,用盐酸浸取,以溴消除砷、锑等元素的干扰,用碘量法测定铜的含量。对滴定条件及共存元素的干扰和消除进行了验证,从而确定了最佳测定条件。实验最佳条件:4 g氢氧化钾和0.5 g硝酸钾混合溶剂;马弗炉温度650 ℃;样品称样量0.300 0 g;硫代硫酸钠标准溶液浓度0.02 mol/L。采用该实验条件,铜冶炼白烟尘中的铜测定结果相对标准偏差在0.37%~0.83%之间(n=10),样品加标回收率为98.30%~101.40%。该方法分析时间短,测定结果准确可靠,具有良好的精密度,可用于铜冶炼白烟尘中铜的测定。     

Na2EDTA返滴定法测定铜镍合金中的镍含量

采用Na₂EDTA返滴定法测定铜镍合金中的镍含量,用柠檬酸钠、硫代硫酸钠和酒石酸作掩蔽剂,丁二酮肟沉淀分离,以二甲酚橙为指示剂,加入过量的Na2EDTA,用氯化锌标准溶液返滴定,能很好地分离铜及其他杂质的干扰。方法用于测定铜镍合金中的镍含量,测定结果的相对标准偏差(RSD,n=9)为0.046%~0.24%,加标回收率为99.3%~101%。能够满足日常样品的检测要求。     

Spectrophotometric determination of calcium in zirconium powder by use of murexide

An accurate spectrophotometric method is proposed for the determination of calcium in zirconium powder by use of murexide. A 0.4-g sample is dissolved in hydrofluoric and sulphuric acids, the solution evaporated to fumes of sulphuric acid, and a mercury cathode electrolysis made if more than 0.05% copper or nickel is present. Ammoniacal precipitation in the presence of ammonium chloride separates zirconium and other elements and an aliquot of filtrate is collected, equivalent to 0.2 g of sample. The ammonium salts are destroyed with nitric and hydrochloric acids and the calcium is determined with murexide. The high reagent blank is shown to be due to the reagent grade nitric acid, hydrochloric acid, and ammonium hydroxide.