表面氨基高密度化介孔氧化硅的合成及其高效去除酸性橙7

以月桂酸为阴离子表面活性剂,3-胺丙基三乙氧基硅烷(APTES)为共结构导向剂,合成了高含量氨基功能化介孔氧化硅材料(AFMS)。以AFMS为吸附剂对溶液中酸性橙7(AO7)进行吸附,对影响AO7吸附效率的相关因素进行了详细研究,结果表明,溶液pH值及温度影响较大。吸附动力学表明,本研究中合成的AFMS对AO7的吸附速率极快。Sips吸附模型对吸附等温线模拟效果最好,从中可知AO7在样品D(由3.0 mL正硅酸乙酯及1.4 mL APTES合成)上的最大吸附量为1.26 mmol·g^-1,远远高于相关文献报道的值。此外,通过吸-脱附循环实验证明,样品D具有良好的稳定性。     

氨基改性介孔二氧化硅的制备及其吸附性能研究

合成了一种具有较大孔径的氨基改性介孔二氧化硅材料(m-MCF)。通过XRD、TEM、低温氮吸附、TGA、FTIR以及原子吸收光谱(AAS)等表征方法对产物的结构和性能进行的分析表明:利用三甲基苯为扩孔剂制备得到的介孔材料具有较大的孔径，有利于功能基团对孔内表面的改性。当氨基改性介孔材料后，该材料仍然保留较大的孔径(22 nm)和较高的比表面积(444 m²·g^-1)。研究发现:与改性而未扩孔的介孔二氧化硅SBA-15相比，该材料对铜离子的吸附能力提高了2倍。     

Jeffamine聚醚胺改性合成介孔及超微孔氧化硅微球

通过对Jeffamine ED2003进行硬脂酸接枝,获得了一种在水溶液中能够进行自组装的新型聚醚酰胺高分子表面活性剂,命名为ED2003-fa-18。以ED2003-fa-18聚醚酰胺高分子表面活性剂为模板,以正硅酸乙酯(TEOS)为无机硅源,在酸性条件下水热合成了介孔及超微孔氧化硅微球。利用粉末X射线衍射(XRD)、N₂物理吸附、红外光谱(IR)、核磁共振波谱(¹H NMR)、扫描电镜(SEM)和透射电镜(TEM)等方法对合成样品进行了表征。研究结果表明,通过改变合成体系中表面活性剂的浓度,可控合成出了有序的介孔及超微孔氧化硅材料。当ED2003-fa-18的浓度为1wt%时,合成的材料为介孔氧化硅,样品的最可几孔径约为2.2nm。当ED2003-fa-18的浓度从3wt%增加到7wt%时,样品的最可几孔径从1.98nm减小到1.94nm,得到的样品为超微孔氧化硅材料。样品的比表面积在500m²·g^-1左右,孔体积在0.3cm³·g^-1左右。由SEM照片可知,所合成的介孔及超微孔氧化硅材料均为由20~30nm的球形纳米颗粒进一步团聚形成的2~4μm的紧密堆积的实心微球。     

Jeffamine聚醚胺改性合成介孔及超微孔氧化硅微球

通过对Jeffamine ED2003进行硬脂酸接枝,获得了一种在水溶液中能够进行自组装的新型聚醚酰胺高分子表面活性剂,命名为ED2003-fa-18.以ED2003-fa-18聚醚酰胺高分子表面活性剂为模板,以正硅酸乙酯(TEOS)为无机硅源,在酸性条件下水热合成了介孔及超微孔氧化硅微球.利用粉末X射线衍射(XRD)、N₂物理吸附、红外光谱(IR)、核磁共振波谱(¹H NMR)、扫描电镜(SEM)和透射电镜(TEM)等方法对合成样品进行了表征.研究结果表明,通过改变合成体系中表面活性剂的浓度,可控合成出了有序的介孔及超微孔氧化硅材料.当ED2003-fa-18的浓度为1wt%时,合成的材料为介孔氧化硅,样品的最可几孔径约为2.2 nm.当ED2003-fa-18的浓度从3wt%增加到7wt%时,样品的最可几孔径从1.98 nm减小到1.94 nm,得到的样品为超微孔氧化硅材料.样品的比表面积在500 m²·g^-1左右,孔体积在0.3 cm³·g^-1左右.由SEM照片可知,所合成的介孔及超微孔氧化硅材料均为由20~30 nm的球形纳米颗粒进一步团聚形成的2~4 μm的紧密堆积的实心微球.     

pH值响应性毒死蜱/铜席夫碱配合物改性SBA-15的制备及缓释性能

以3-氨丙基三乙氧基硅烷（APTES）、水杨醛和铜离子为改性剂,通过后嫁接法制得铜席夫碱配合物改性SBA-15（Cu-SBA-15）,并以毒死蜱为模型药物,制备了毒死蜱/铜席夫碱配合物改性SBA-15缓释体系。利用TEM、SEM、XRD、N₂吸附-脱附、TG、FTIR和XPS对SBA-15、氨基改性SBA-15（NH₂-SBA-15）、水杨醛希夫碱改性SBA-15（SA-SBA-15）的形貌、结构和Cu-SBA-15的配位情况进行了表征,考察了SBA-15在改性前后对毒死蜱的吸附量和缓释性能,并着重探究了毒死蜱/铜席夫碱配合物改性SBA-15载药体系在不同pH值下的释药行为。结果表明,APTES和水杨醛能够通过后嫁接法修饰于SBA-15,修饰后仍保持十分有序的孔道结构。SBA-15通过改性后,其对毒死蜱的吸附量由100 mg·g^-1增加至195 mg·g^-1,且其对药物的缓释性能也得到改善。毒死蜱/铜席夫碱配合物改性SBA-15缓释体系显示出明显的pH值响应性,pH=3时的释药速率大于pH=11时,而在中性条件下的缓释效果相对最好。载药体系的释药行为可用Riger-Peppas动力学模型来描述,其药物释放由Fick扩散控制。     

氨基功能化SBA-15的直接合成及其对CO_2的吸附性能研究

通过直接法合成了氨基功能化SBA-15介孔材料。使用X-射线粉末衍射法(XRD),N2吸-脱附,透射电子显微(TEM)等技术对氨基功能化材料进行了表征。实验结果表明:当反应原料中nAPTES/(nAPTES+nTEOS)≤0.20时,APTES功能化的材料都具有典型的介孔SBA-15结构;但当nAPTES/(nAPTES+nTEOS)≥0.225时,由于氨基对SBA-15结构的副作用导致SBA-15介孔结构坍塌。在氟离子辅助合成下可以获得高含量氨基(反应原料中nAPTES/(nAPTES+nTEOS)的比值为0.25)功能化的SBA-15材料,且此材料中的介孔孔径和BET比表面积都较大。CO2吸附结果表明,随着反应原料中APTES含量提高,所合成的材料对CO2的吸附量相应增加,同时在101kPa和25℃下,通过氟离子辅助合成的材料对CO2的吸附量远远优于无氟离子辅助合成材料的。本研究还对后嫁接法和直接合成法获得氨基功能化SBA-15介孔材料的优缺点进行了讨论。     

功能化有序介孔碳对重金属离子Cu(II)、Cr(VI)的选择性吸附行为

以三嵌段共聚物F127为模板剂, 酚醛树脂为碳源, 正硅酸乙酯为硅源, 三组分共组装合成介孔碳?氧化 硅纳米复合物, 再经HF去除氧化硅, 得到有序介孔碳(OMC). X射线衍射(XRD)、透射电子显微镜(TEM)、低温 N2吸脱附(BET)等测试表明, 所得样品具有高度有序的介孔结构, 比表面积和孔容分别为1330 m²·g^-1和2.13 cm³·g^-1, 平均孔径6.4 nm. 对其先氧化、后氯化、再胺化, 得到不同胺基接枝量的胺化介孔碳(C-NH₂(m), m为加入的乙二胺的质量(g)). 傅里叶变换红外(FT-IR)光谱表征结果证实, 胺基官能团成功接枝到有序介孔碳表面.TEM测试表明介孔碳的有序孔道结构得到了较好的保持. 以有序介孔碳、胺化介孔碳作吸附剂对Cu(II)、Cr(VI)进行选择性吸附研究. 结果表明: 功能化修饰前, 样品对Cu(II)、Cr(VI)饱和吸附量分别为213.33、241.55 mg·g^-1; 修饰后饱和吸附量可分别达到495.05、68.21 mg·g^-1. 功能化介孔碳表现了较强的选择性吸附Cu(II)的能力.     

氨基功能化SBA-15介孔分子筛的制备与表征

以3-氨丙基三乙氧基硅烷为偶联剂,采用后合成法对介孔分子筛(SBA-15)的表面进行改性,制得氨基功能化的介孔NH<,2>-SBA-15材料(简称NH<,2>-SBA-15),其结构和性能经FT-IR,元素分析,XRD,SEM及低温N<,2>吸附-脱附表征.结果表明,氨基成功地嫁接到SBA-15表面,含量高达3.47 ...     

锂硫电池正极用硫/介孔碳复合材料的制备及电化学性能

制备了以十二烷基硫酸钠(SDS)为模板的介孔碳,并将介孔碳和单质硫采用熔融渗透法复合制得硫/介孔碳复合材料。SEM、TEM和BET结果显示介孔碳成直径约为500 nm的大小均一的球体,存在孔径为2 nm的微孔;单质硫充分填充在介孔碳的微孔中。以硫/介孔碳复合物作为锂硫电池正极材料时显示出高的电化学性能。初始放电容量高达1519 mAh·g^-1,在200 mA·g^-1的电流密度下充放电200个循环后依然能保持在835 mAh·g^-1。硫/介孔碳复合材料的高倍率性能和优异的循环稳定性,源于介孔碳良好的导电性及其孔结构的固硫作用。     

介孔碳/石墨烯复合材料的制备及其醌类改性电容性能

首先利用硬模板法制备出介孔碳/石墨烯复合材料,然后向复合材料中引入具有赝电容活性的醌类分子进一步增大材料的电容性能。研究结果表明,负载30%（w/w）叔丁基氢醌的介孔碳/石墨烯复合材料具有最佳的电容性能,在电流密度为0.5 A·g^-1时,比电容值为355 F·g^-1;当电流密度高达30 A·g^-1时,其比电容值高达226 F·g^-1,比电容保持率为64%,表现出良好的速率特性。     

Direct synthesis and catalytic applications of ordered large pore aminopropyl-functionalized SBA-15 mesoporous materials

SBA-15 mesoporous silica has been functionalized with aminopropyl groups through a simple co-condensation approach of tetraethyl orthosilicate (TEOS) and (3-aminopropyl)triethoxysilane (APTES) using amphiphilic block copolymers under acidic conditions. The organic-modified SBA-15 materials have hexagonal crystallographic order, pore diameter up to 60 A, and the content of aminopropyl groups up to 2.3 mmol g(-1). The influences of TEOS prehydrolysis period and APTES concentration on the crystallographic order, pore size, surface area, and pore volume were examined. TEOS prehydrolysis prior to the addition of APTES was found essential to obtain well-ordered mesoporous materials with amino functionality. The amount of APTES incorporated in the silica framework increased with the APTES concentration in the synthesis gel, while the ordering of the mesoporous structure gradually decreased. Analysis with TG, IR, and solid state NMR spectra demonstrated that the aminopropyl groups incorporated in SBA-15 were not decomposed during the preparation procedure and the surfactant P123 was fully removed through ethanol extraction. The modified SBA-15 was an excellent base catalyst in Knoevenagel and Michael addition reactions.     

Preparation of ordered large pore SBA-15 silica functionalized with aminopropyl groups through one-pot synthesis

Highly ordered large pore SBA-15 silica functionalized with up to 16% aminopropyl groups, which gave high catalytic activity and selectivity toward flavanone synthesis through aldol condensation and subsequent intramolecular Michael addition of benzaldehyde and 2'-hydroxyacetophenone, was synthesized for the first time via co-condensation of tetraethylorthosilicate (TEOS) and 3-aminopropyltriethoxysilane (APTES) using an amphiphilic block copolymer as the structure-directing agent.     

Surface functionalization of ordered mesoporous carbons--a comparative study

Hexagonally structured mesoporous carbons C15 and CMK-5 and cubically structured carbon C48 were synthesized using ordered silica SBA-15 and MCM-48 as templates and carbon precursors of different structures. The surfaces of these ordered carbons were chemically functionalized by employing an approach, in which the selected diazonium compounds were in situ generated and reacted with the carbon frameworks of the mesoporous carbons. The aromatic organic molecules containing chlorine, ester, and alkyl groups were covalently attached to the surface of these ordered mesoporous carbons. The presence of functional groups on the modified carbons was confirmed with Fourier transform infrared spectroscopy, thermogravimetric analysis, and nitrogen adsorption. The BET-specific surface area and the pore width of ordered carbons were significantly reduced, whereas the primary structure of these ordered carbons and their unit cells were intact. Basically, the density of grafted functional groups is related to the specific surface area of the sample, particularly the surface area of mesopores. The surface functionalization reaction takes place only on the external surface of carbon C15, while it occurs on both of the internal and external surface of CMK-5 carbon with the nanopipe structure. The presence of the micropores in CMK-5 carbon should be responsible for its lower grafting density because the small micropores are inaccessible in the reaction. It was also proposed that the preferred adsorption/reaction in C48 may be related to the observed unsymmetrical degradation of the XRD patterns for the functionalized C48 samples. The chemical modification process considerably reduced the primary mesopores in these ordered carbons by approximately 1-1.5 nm, affording carbons with micropores in the cases of C15 and C48, and mixed micropores and small mesopores in the case of CMK-5. A grafting density of approximately 0.9-1.5 micromol/m(2) was achieved under current research.     

SBA-15表面改性及其对介孔La0.8Sr0.2CoO3钙钛矿型催化剂结构和性能的影响

Mesoporous SBA-15 with mesopore diameter up to 10.1 nm was prepared by a hydrothermal method, and was further functionalized to obtain different surface properties. Thus-prepared SBA-15 was employed as a template to synthesize rhombohedrally crystallized mesoporous La_0.8Sr_0.2CoO₃ perovskite via a nanocasting method. The surface properties of the SBA-15 were adjusted by treatment with concentrated hydrochloric acid, trimethylchlorosilane (TMCS), and 3-aminopropyltriethoxysilane (APTES). A series of characterization techniques verified that all the synthesized templates possessed ordered two-dimensional hexagonal mesoporous structure, and the surface was successfully modified with methyl and amino groups. The mesoporous perovskite structure was formed in the samples and the surface properties of SBA-15 significantly influenced the structure and properties of La_0.8Sr_0.2CoO₃ perovskite oxides. Wide-angle X-ray diffraction patterns suggested that the modified silica templates were conducive to the formation of pure perovskite frameworks with good crystallinity. The catalysts also possessed mesoporous structure, as confirmed by small-angle XRD patterns, high-resolution transmission electron microscopy images, and nitrogen adsorption analysis. Moreover, the La_0.8Sr_0.2CoO₃ materials synthesized using surface-functionalized templates exhibited relatively higher catalytic activity and stability in CO oxidation. Complete CO conversion could be achieved at 140℃ using the thus-prepared La_0.8Sr_0.2CoO₃ materials, and no significant loss in catalytic activity was observed after 100 h of on-stream reaction experiments. X-ray photoelectron spectroscopy, H₂ temperature-programmed reduction, and O₂ temperature-programmed desorption experiments revealed that the existence of Co⁴⁺, Sr enrichment in the perovskite structure, and high content of adsorbed oxygen species play a critical role in the enhanced catalytic activity of the catalysts. We also proposed the possible reasons for the effect of surface properties of the silica templates on the structure and properties of the La_0.8Sr_0.2CoO₃ nanomaterials.     

Functionalized silica matrices for controlled delivery of cephalexin

The surface of SBA-15 ordered mesoporous silica was functionalized with sulphonic and amine functional groups to determine the effect of changes in surface acidity on cephalexin adsorption and subsequent release. Cephalexin (CPX), which belongs to the group of cephalosporins or β-lactam antibiotics, was impregnated on functionalized SBA-15. The functionalized silica materials were characterized by SEM, TGA, FTIR and N₂ adsorption, and an in vitro drug delivery test was performed. SEM micrographs showed the packed cylinders correspond to SBA 15 materials. Likewise, N₂ adsorption–desorption isotherms demonstrated that the SBA-15 structure was obtained when IV-type isotherms were displayed. The inalterable stabilization of the drug was confirmed by FTIR spectroscopy. For all the samples studied, the delivery profiles exhibit two steps. A fast initial stage was obtained over the first 5 h, followed by a slower one. Regarding this second stage, the time needed to attain a plateau was undoubtedly altered by the surface functionalization.     

Synthesis and characterization of surface modified SBA-15 silica materials and their application in chromatography

Hexagonally ordered SBA-15 mesoporous silica spheres with large uniform pore diameters are obtained using the triblock copolymer, Pluronic P123, as template with a cosurfactant cetyltrimethylammonium bromide (CTAB) and the cosolvent ethanol in acidic media. A series of surface modified SBA-15 silica materials is prepared in the present work using mono- and trifunctional alkyl chains of various lengths which improves the hydrothermal and mechanical stability. Several techniques, such as element analysis, nitrogen sorption analysis, small angle X-ray diffraction, scanning electron microscopy (SEM), FTIR, solid-state (29)Si and (13)C NMR spectroscopy are employed to characterize the SBA-15 materials before and after surface modification with the organic components. Nitrogen sorption analysis is performed to calculate specific surface area, pore volume and pore size distribution. By surface modification with organic groups, the mesoporous SBA-15 silica spheres are potential materials for stationary phases in HPLC separation of small aromatic molecules and biomolecules. The HPLC performance of the present SBA-15 samples is therefore tested by means of a suitable test mixture.     

Effects of Morphology and Structural Characteristics of Ordered SBA-15 Mesoporous Silica on Release of Ibuprofen

Three kinds of highly ordered SBA-15 mesoporous materials with different pore sizes and morphologies denoted as LPS-SBA-15 (stick-like with pore size 7.28 nm), CPS-SBA-15 (stick-like with pore size 5.96 nm) and T-SBA-15 (tablet-like with pore size 4.64 nm) have been prepared, characterized and employed as carrier materials. The release behaviors of the ibuprofen in a simulated body fluid from these mesoporous silica materials were studied. The influences of pore size and exterior morphologies of mesoporous silica on the release behaviors of ibuprofen have been investigated. It has been found that the release becomes fast with increasing of pore size and slow with extending of transport pathway, and that the release rate of ibuprofen from the three kinds of SBA-15 is LPS-SBA-15 > T-SBA-15 > CPS-SBA-15. The results show that the inner structure as well as the exterior morphologies of SBA-15 mesoporous silica can seriously affect the release behaviors of ibuprofen.     

Metallic nickel supported on mesoporous silica as catalyst for hydrodeoxygenation: effect of pore size and structure

Catalytic hydrodeoxygenation (HDO) of anisole, a methoxy-rich lignin-derived bio-oil model compound, was carried out over a series of Ni-containing (5, 10, 20, and 30 wt%) catalysts with commercial silica and ordered mesoporous silica SBA-15 as support. Both supports and catalysts were characterized by N₂ adsorption–desorption isotherms, X-ray diffraction, CO chemisorption, and transmission electron microscopy (TEM). Catalytic reaction was performed at 250 °C and 10 bar H₂ pressure. Depending on the catalyst support used and the content of active metal, the catalytic activity and product distribution changed drastically. Increase of the nickel loading resulted in increased anisole conversion and C₆ hydrocarbon (benzene and cyclohexane) yield. However, loading more Ni than 20 wt% resulted in a decrease of both conversion and C₆ yield due to agglomeration of Ni particles. In addition, Ni/SBA-15 samples exhibited much stronger catalytic activity and selectivity toward C₆ hydrocarbon products compared with Ni/silica catalysts. The differences in catalytic activity among these catalysts can be attributed to the effect of the pore size and pore structure of mesoporous SBA-15. SBA-15 can accommodate more Ni species inside channels than conventional silica due to its high pore volume with uniform pore structure, leading to high HDO catalytic activity.     

疏水性Cosalen/SBA-15的制备及在甲苯选择性氧化中的应用

以介孔分子筛SBA-15为载体, 先采用γ-氨丙基三乙氧基硅烷(APTES)进行氨基硅烷化修饰, 然后经甲基三乙氧基硅烷(MTES)疏水修饰后固载双水杨醛缩乙二胺合钴配合物(Cosalen). 采用傅里叶变换红外光谱、 紫外-可见漫反射光谱、 X射线光电子能谱、 元素分析、 等离子体发射光谱、 X射线衍射和氮气物理吸附等手段对制备的固载型催化剂Cosalen/SBA-15进行了物相结构和修饰程度的表征, 并考察了样品对甲苯、 苯甲醛和苯甲醇的吸附性能及在甲苯液相氧化反应中的催化性能. 结果表明, 固载型催化剂Cosalen/SBA-15的介孔结构和孔道有序性保持良好, Cosalen通过与氨基配位固载在修饰后的载体SBA-15上, 且高度分散, 氨基硅烷化和甲基修饰明显增强了其表面疏水性能, 对苯甲醛和苯甲醇的吸附量降低. 疏水性Cosalen/SBA-15协同N-羟基邻苯二甲酰亚胺(NHPI)催化甲苯液相分子氧氧化反应, 无溶剂体系在130 ℃下反应2 h, 甲苯转化率达到16.0%, 产物中苯甲醛和苯甲醇的总选择性为32.0%, 在一定程度上抑制了极性产物深度氧化为苯甲酸. 高温不利于苯甲醛和苯甲醇选择性的提高, 降低温度至110 ℃, 甲苯转化率达到12.9%时, 苯甲醛和苯甲醇的总选择性提高到43.9%.     

Effect of synthesis conditions on the mesoscopical order of mesoporous silica SBA-15 functionalized by amino groups

Mesoporous amine-functionalized SBA-15 silica has been synthesized directly by the co-condensation of tetraethyl orthosilicate (TEOS) and aminopropyl-trimethoxysilane (APTMS) under acidic conditions with an APTMS/(APTMS + TEOS) molar ratio of 10%. The effect of synthesis conditions, including TEOS pre-hydrolysis, as well as the heating temperature and time, on the mesoscopical order and pore structure of the functionalized SBA-15 have been studied in detail by means of powder X-ray diffraction, nitrogen sorption, transmission electron microscopy, infrared spectra and solid state ²⁹Si nuclear magnetic resonance. A functionalized SBA-15 silica with a highly ordered two-dimensional P6 mm hexagonal symmetry and a narrow pore size distribution centered at 6 nm can be obtained if TEOS is allowed to pre-hydrolyze for 2 h. For the sample with TEOS pre-hydrolysis time of 4 h, aging at 50°C or 150°C leads to a more ordered pore arrangement compared to 100°C and also a narrower pore size distribution with larger pore volume. Increasing aging time is in favor of the formation of mesoscopically ordered structure, but fails to obtain a superior pore structure.