低功率超声增强碘帕醇氯氧化的效果和路径

研究了低功率超声(US, <38 W)对NaClO氧化非离子型碘代X射线造影剂—碘帕醇(IPM)的增强作用及机理, 考察了NaClO添加浓度和超声功率的影响, 分析并计算了体系中的主要活性物种及其贡献. 采用高效液相色谱/串联质谱(HPLC/MS/MS)对降解产物进行分析, 推测IPM的降解路径. 结果表明, 低功率US显著增强了NaClO对IPM的氧化效果, 在25 ℃, pH=5.8, NaClO浓度为0.12 mmol/L条件下, 10 mg/L IPM在60 min的降解率达到85.8%. 其中NaClO氧化、 HO·和活性氯自由基(RCSs)是US/NaClO增强IPM降解的主要原因, 自由基分析计算它们的贡献率分别为15.82%, 4.65%和79.53%. NaClO浓度在0~0.24 mmol/L范围内, IPM的降解率随NaClO浓度升高而增加, 60 min后降解率由4.75%增加到91.12%; 超声功率为28.5 W, 降解率达到最高. 在 15~45 ℃温度范围内, IPM的降解过程符合表观一级反应动力学, 反应活化能(E_a)为59.03 kJ/mol. HPLC/MS/MS共检测出5种中间产物, 结合密度泛函理论(DFT)计算结果, 初步推测了IPM在US/NaClO体系中的降解途径和机理.     

TiO2/H2O2/超声波协同降解壬基酚聚氧乙烯醚溶液

采用经过处理的锐钛矿型TiO2作为催化剂,在H2O2存在下,以TiO2/H2O2/超声波协同降解壬基酚聚氧乙烯醚反应为模型,探讨了TiO2催化剂用量、H2O2用量、超声波功率、壬基酚聚氧乙烯醚溶液初始浓度、初始pH值对壬基酚聚氧乙烯醚降解率的影响。结果表明,在一定的超声波功率和一定的TiO2用量范围内,壬基酚聚氧乙烯醚降解率随超声波功率和TiO2用量的增大而增大,达到一定值后保持平稳;当H2O2浓度介于一定范围内,增大H2O2用量可提高壬基酚聚氧乙烯醚的降解率,但H2O2用量过多时,反而会使壬基酚聚氧乙烯醚的降解率下降;pH<5时,壬基酚聚氧乙烯醚降解效果较好,且pH值越小,降解率越高;pH>5时,降解率越来越低。TiO2/H2O2/超声波体系降解壬基酚聚氧乙烯醚产生了较强烈的协同效应,在同一时刻三者协同体系的降解率比其3种单独体系的降解率之和高出约60%;在TiO2催化剂用量0.4g/L、H2O2用量0.2g/L、超声波功率600W、降解时间120min的条件下,对初始质量浓度为80mg/L,pH=1的壬基酚聚氧乙烯醚溶液进行降解,其降解率达98%以上。     

超声波提取川贝母黄酮类物质的工艺优化

采用超声波提取技术提取川贝母中的黄酮类物质.考察了超声功率、乙醇体积分数、料液比、超声时间和超声温度各因素对黄酮类物质提取效率的影响.在超声功率800 W条件下,通过L_9(3~4)正交试验,确定了川贝母黄酮类物质的超声波最佳提取工艺参数:超声功率为800 W,乙醇体积分数为80%,料液比为1 g∶45 mL,超声时间为2.0 h,超声温度为45℃.在最佳提取工艺条件下进行验证试验,川贝母黄酮类物质的提取率达到77.13 mg/g,RSD值为0.39%.     

超声波辐照和臭氧氧化协同降解废水中的结晶紫

采用超声波辐照、臭氧氧化以及超声波辐照-臭氧氧化降解废水中的结晶紫;考察了废水初始pH、超声波功率和频率、氧气流量、反应温度等因素对降解效率的影响.结果表明:超声波和臭氧对结晶紫的降解具有协同作用;当废水溶液初始质量浓度为200mg.L-1、pH为10.0时,控制超声波功率和频率分别为100 W和30kHz,氧气流量为0.4L.min-1,反应温度为25℃,反应时间为90 min,则总有机碳(TOC)的去除率可达89.2%,相应的一级反应速率常数为2.38×10-2min-1.     

声化学降解染料结晶紫的研究

采用频率为20 kHz的超声波降解阳离子染料结晶紫(CV)溶液,考察了溶液初始浓度、pH值、声能强度、时间、温度等因素对染料声化学降解过程的影响.实验结果表明,溶液初始浓度为30 mg/L、pH=8.0、声强=47.5 W/cm2、超声辐照50 m in,CV的脱色率达97.8%;CV的超声降解过程以高温热解反应为主,服从动力学一级反应;当超声/H2O2、超声/镁联合作用时,二者产生协同效应,溶液中产生大量OH自由基,强化了CV的声化学脱色和降解过程.     

超声波光催化协同降解对甲基苯磺酸

以对甲基苯磺酸水溶液为研究对象,进行了超声波、光催化单独处理以及超声波与光催化联合处理的研究.探讨了超声功率、频率、溶液初始pH等因素对对甲基苯磺酸的降解效率的影响.结果表明,超声波和光催化之间存在着协同效应;当溶液初始质量浓度30mg/L、光催化剂Tio2投加量为1OOmg/L、超声功率和频率分别为80W和45kHz...     

三维电极系统电化学氧化三唑酮

以三唑酮(TDF)为目标污染物,以钛基钌铱电极和不锈钢板作阳极、阴极,颗粒活性炭(GAC)为粒子电极构建三维电极系统,通过搅拌实现粒子电极呈流化状态。研究电流密度、TDF初始浓度、GAC投加量、初始pH对三维电极系统的TDF去除效率的影响。研究结果表明:增大电流密度有助于提高TDF去除效率;TDF去除率随初始pH的增大呈现逐渐增大的趋势,碱性条件有助于TDF的去除;当GAC投加量为1～4 g/L时,增大GAC投加量有助于TDF的降解;增大TDF初始浓度会导致去除率的降低。当TDF初始浓度为200μg/L、电流密度为8m A/cm2、初始pH=11、GAC投加量为4 g/L时,电化学氧化10 min时TDF去除率达到99.95%。三维电极系统的传质效率高于二维电极系统,三维电极电化学氧化系统是一种适用于降解TDF的高级氧化技术。     

壳寡糖的酶法制备

通过还原端基、酶解产物聚合度、水解液调碱性后透光率的测定以及酶解产物的TLC、HPLC分析,研究了壳聚糖酶降解壳聚糖过程中壳聚糖浓度、酶用量、反应时间和pH对酶促反应速率和产物聚合度的影响。结果表明:壳聚糖酶在底物浓度0.03 g/mL、壳聚糖酶用量4~6 u/g、pH=5.8和水解200 min时,可得到以聚合度3~7为主的壳寡糖。     

超声强化Keggin型Fe-Mo-Zr杂多酸盐降解染料废水

合成了Fe-Mo-Zr杂多酸盐催化剂,并利用红外光谱(IR)和X射线衍射(XRD)对制得的产物进行了表征,研究了Fe-Mo-Zr杂多酸盐超声降解模拟酸性绿B(AGB)染料废水的效果.结果表明,合成的杂多酸盐具有Keggin型结构,催化剂的投加量、染料的初始浓度及初始pH值、超声频率及超声时间都对降解效果产生一定的影响.当染料浓度为10mg/L,催化剂的投加量为0.6g/L时,在pH为5.0的条件下,用40kHz超声辐射60min,降解率最高可达93.18%.通过动力学分析:降解反应符合一级反应动力学模型,速率常数随初始浓度的增加而减小.     

电子束辐照下呋喃西林代谢产物降解的质谱检测

提出用电子束辐照技术降解去除水溶液中的呋喃西林代谢形成的氨基脲（SC）.采用LC-MS/MS方法分析SC含量变化.结果表明：当SC质量浓度小于0.67mg/L、辐照强度大于8 kGy时,SC降解率高达90%以上,没有检测到明显的降解产物.可见,电子束辐照降解法是-种简便、有效的有机污染物去除方法.     

超声波-二氧化钛光催化耦合法降解高效氯氰菊酯

采用超声波-TiO2光催化耦合法降解高效氯氰菊酯,考察了高效氯氰菊酯初始浓度、降解时间、溶液pH、催化剂用量等对高效氯氰菊酯农药残留的降解效果,并利用水果进行了实物模拟.结果表明:利用超声波-TiO2光催化耦合法能够有效地降解高效氯氰菊酯农药残留.在弱酸环境中,当纳米TiO2投放量为1.2g/L时,经2h超声催化降解,不同浓度的高效氯氰菊酯农药稀释液均被有效降解,降解率最高可达98.3%.     

超声协同TiO_2光催化脱除燃料油中有机硫的研究

采用溶胶凝胶法制备纳米TiO2光催化剂,引入超声作用,以空气中的氧气为氧化剂,正辛烷为模拟油品对燃料油中硫化物的脱除进行了研究。考察了光照强度、催化剂用量、反应时间、二苯并噻吩(DBT)初始浓度、超声功率等因素对TiO2光催化二苯并噻吩溶液降解效率的影响。结果表明,引入超声后DBT的降解率提高了10%左右,并在TiO2用量为2 g/L,通气量为800 mL/min,光照距离20 cm,DBT初始浓度为600 mg/L,反应时间为150 min,超声功率为500 W的条件下,DBT降解率达到了72.6%。     

Degradation of sulfadiazine antibiotics by water falling film dielectric barrier discharge

A new water falling film dielectric barrier discharge was applied to the degradation of sulfadiazine in the aqueous solution. The various parameters that affect the degradation of sulfadiazine and the proposed evolutionary process were investigated. The results indicated that the inner concentrations of 10 mg/L sulfadiazine can be all removed within 30 min. The optimum pH value was 9.10 and both strong acidic and alkaline solution conditions were not suitable for the degradation. The degradation of sulfadiazine can be enhanced by the addition of hydrogen radical scavengers, but be inhibited by adding hydroxyl radical scavengers. The water falling film dielectric barrier discharge was rather ineffective in mineralization, because of the intermediates were recalcitrant to be degraded. The existence of Fe2+and CCl4 in the liquid phase can promote the degradation and mineralization of sulfadiazine. It was found that the degradation of SDZ was enhanced by CCl4 was mainly because of the increase of OH due to the reaction of CCl4 with H that reduce the chances of their recombination with OH. Based on the 8 intermediate products identified by LC–MS, the proposed evolution of the degradation process was investigated.     

Analysis of streptolydigin degradation and conversion in cultural supernatants of <Emphasis Type="Italic">Streptomyces lydicus</Emphasis> AS 4.2501

A variety of structural analogues of streptolydigin exists in the cultural supernatants of Streptomyces lydicus AS 4.2501. The degradation of streptolydigin in cultural supernatants with different pH values kept at 25°C in a thermostatic bath was investigated using LC-MS/MS detection. Analysis of the alkaline supernatants (pH 9.50) provides evidence of degradation and conversion between streptolydigin and its structural analogues. Interestingly, a new streptolydigin analogue was detected by LC-MS and photo-diode array (PDA) detection in the process of alkaline degradation. After 48 h in a thermostatic bath, the degradation of streptolydigin and its two analogues at pH 9.50 approached pseudo-first order kinetics. Comparatively, the degradation of streptolydigin was much more rapid in the cultural supernatants with pH 3.05, only requiring 2 hours. Qualitative analysis of the degradation products by LC-MS/MS and PDA indicated that hydrolysis of the epoxy ether bond and acid amide bond was the major mechanism of degradation in acidic cultural supernatants. Two degradation products in the acid supernatant were assumed.     

Stress degradation study and structure characterization of oxidation degradation product of dexlansoprazole using liquid chromatography-mass spectrometry/time of flight,liquid chromatography-tandem mass spectrometry and nuclear magnetic resonance

The present study deals with the forced degradation behavior of dexlansoprazole under International Conference on Harmonisation (ICH) prescribed stress conditions. The drug was found to be more labile under acid, base, neutral, oxidative hydrolysis and thermal stress, while it was moderately stable under photolytic conditions. The known and unknown degradation products were separated on a C-18 column using a stability-indicating method. Liquid chromatography-mass spectrometry (LC-MS) analysis was performed for all the degradation studies. Isolation and structure characterization of oxidation degradation products were executed using sophisticated tools, viz. preparative high performance liquid chromatography (HPLC), liquid chromatography-mass spectrometry/time of flight (LC-MS/TOF), liquid chromatography-tandem mass spectrometry (LC-MS/MS), and nuclear magnetic resonance (NMR). This study demonstrates an ample methodology of degradation studies and structure elucidation of unknown degradation products of dexlansoprazole, which helps in the development and stability study of active pharmaceutical ingredients and formulated products.     

液相色谱-飞行时间质谱、液相色谱-串联质谱和核磁共振用于右旋兰索拉唑的强制降解研究和氧化降解产物的结构表征(英文)

The present study deals with the forced degradation behavior of dexlansoprazole under International Conference on Harmonisation(ICH)prescribed stress conditions. The drug was found to be more labile under acid,base,neutral,oxidative hydrolysis and thermal stress,while it was moderately stable under photolytic conditions. The known and unknown degradation products were separated on a C-18 column using a stabilityindicating method. Liquid chromatography-mass spectrometry(LC-MS)analysis was performed for all the degradation studies. Isolation and structure characterization of oxidation degradation products were executed using sophisticated tools,viz. preparative high performance liquid chromatography(HPLC),liquid chromatographymass spectrometry / time of flight(LC-MS / TOF),liquid chromatography-tandem mass spectrometry(LC-MS /MS),and nuclear magnetic resonance(NMR). This study demonstrates an ample methodology of degradation studies and structure elucidation of unknown degradation products of dexlansoprazole,which helps in the development and stability study of active pharmaceutical ingredients and formulated products.     

Kinetics and mechanism for the sonophotocatalytic degradation of p-chlorobenzoic acid

The advanced oxidation processes of sonolysis (213 kHz), photocatalysis, and a hybrid combination of both (sonophotocatalysis) have been used in the degradation of a representative aromatic carboxylic acid, p-chlorobenzoic acid (PCBA), in ambient air saturated aqueous solutions. The formation of degradation products were monitored quantitatively and qualitatively using HPLC and MS/MS. A kinetic model was used to account for the degradation of the PCBA in the presence of intermediate degradation products and also their formation and subsequent degradation. Under certain experimental conditions a small (20% enhancement) synergistic effect in the degradation rate was evident in the combined process compared with the sum of the individual processes.