甲苯-2,4-二异氰酸酯修饰蒙脱土及聚苯乙烯蒙脱土纳米复合材料的制备与表征

用FTIR和WAXD法研究了甲苯-2,4-二异氰酸酯(TDI)的邻位和对位异氰酸酯基团与蒙脱土表面羟基的修饰反应,在此基础上提出了结构模型;用TDI修饰后的蒙脱土成功制备了插层型聚苯乙烯/蒙脱土纳米复合材料,并用WAXD和TEM进行了表征.实验结果表明,修饰后TDI与蒙脱土表面形成化学键,使蒙脱土的片层间距显著增大,十六烷基三甲基溴化铵(CTAB)在蒙脱土层间由双层平行排列转变为双层脂肪链倾斜方式排列.在苯乙烯插层聚合过程中,蒙脱土层间距进一步扩大,其初级粒子在聚苯乙烯基体中的厚度约20～50nm.     

纳米SiO_2锚固光敏基团引发MMA光接枝聚合研究

对纳米SiO2进行了锚固光引发剂的表面修饰,进而引发甲基丙烯酸甲脂(MMA)光接枝聚合制备有机/无机复合粒子.纳米SiO2粒子首先用氯化亚砜进行表面氯化,再与光引发剂2-羟基-4-(2-羟基乙氧基)-2-甲基苯丙酮(Irgacure2959)反应从而锚固上光引发剂.通过紫外光引发MMA在经过修饰过的纳米SiO2表面上进行表面光接枝聚合.采用IR、TGA和TEM等方法表征了接枝前后纳米粒子的变化,证明了表面接枝物的存在,并研究了不同反应条件对单体转化率、接枝率和接枝效率的影响.研究结果表明,搅拌对接枝过程的影响比较显著.TGA结果显示未搅拌聚合时接枝率只能达到比较小的程度,而在搅拌条件下180min内MMA的接枝率可达到110%.     

二氧化硅纳米粒子表面修饰及其表征

采用溶胶-凝胶法合成粒径在50—150nm范围内的二氧化硅（SiO2）纳米粒子。用甲基丙烯酸-3-（三甲氧基硅基）丙酯（MPS）对SiO2纳米粒子表面进行修饰，使其表面接枝能参与自由基聚合反应的碳碳双键基团。用元素分析、FTIR、^13C CP／MASNMR和^29Si CP／MASNMR等手段对修饰过的SiO2纳米粒子进行表征，以确证MPS接枝在SiO2纳米粒子上。分析修饰过的SiO2纳米粒子的^29Si CP／MASNMR和FTIR谱图，还可初步推断MPS接枝在SiO2纳米粒子表面的机理：MPS首先发生水解缩合反应形成低聚物，然后通过氢键作用吸附到SiO2纳米粒子表面，最后MPS低聚物中未缩合的硅羟基与SiO2纳米粒子表面的硅羟基发生缩合反应。     

聚乙烯—丙烯酸与聚（2—乙基—2—恶唑啉）接枝共聚物的合成及表征

选用聚乙烯－丙烯酸（ＥＡＡ）为接枝母体,首先摸索出２－乙基－２－恶唑啉阳离子开环聚合的规律,得到高转化率端基为活性翁离子的聚（２－乙基－２－恶唑啉）（ＰＥＯＸ）,再与ＥＡＡ羟基侧基进行接枝反应,考察了开环聚合条件及接枝反应条件对接枝率的影响,在一定的条件下得到了接枝率〉２５％的聚乙烯－丙烯酸与聚（２－乙基－２－恶唑啉）的接枝共聚物（ＥＡＡ－ｇ－ＰＥＯＸ）。该接枝物用于聚对苯二甲酸丁醇酯／聚丙烯（Ｐ     

树状功能高分子负载锡配合物的合成及其催化酮的Baeyer-Villiger氧化反应性能研究

通过固相合成方法将聚酰胺-胺树状分子担载于氯球上,对其外围分别用2,4-二羟基苯甲醛和邻羟基苯甲醛进行修饰,再与SnCl2.2H2O反应,形成配体不同的两类树状高分子锡配合物.将此类配合物用作30%的双氧水氧化酮的Baeyer-Villiger反应的非均相催化剂,具有较好的催化活性.2-金刚烷酮、环己酮、3-甲基-2-戊酮等都转化为相应的酯和内酯,底物的转化率和产物选择性均较高.对2-羟基苯甲醛、2,4-二羟基苯甲醛和邻羟基苯甲醛修饰的不同类型催化剂催化下的反应进行比较,发现配体对锡的担载量和催化活性均有不同程度的影响.其中邻羟基苯甲醛修饰的配合物因具有较高的锡担载量而具有了最佳的催化活性.此催化体系使用环境友好的低浓度双氧水为氧化剂,催化剂制备方法简单、催化反应完成时间短、催化剂在多次重复利用后活性没有明显降低,可回收和重复利用.     

聚己内酯接枝淀粉纳米晶的制备

本文通过异氰酸酯与端羟基聚己内酯反应制备端异氰酸酯基预聚体,再接枝到淀粉纳米晶表面,制备了端基分子量可控的聚己内酯接枝淀粉纳米晶。分别用FTIR和1HNMR对所制备的聚己内酯接枝淀粉纳米晶进行表征,结果表明有少量聚己内酯接枝到淀粉纳米晶表面。XRD结果表明,接枝少量聚己内酯的淀粉纳米晶的晶型和结晶度基本不变。聚己内酯接枝淀粉纳米晶的熔融温度由115℃左右提高到122℃左右,并且温度范围变宽。浸润性实验表明,聚己内酯接枝淀粉纳米晶与水不浸润,其表面已具有疏水性。聚己内酯仅接枝在淀粉纳米晶的表面,改善了淀粉纳米     

丙烯酸基蓖麻油氨基甲酸酯齐聚物的合成和表征

合成和表征了丙烯酸基蓖麻油氨基甲酸酯齐聚物(VTPU)。证明:2,4-甲苯二异氰酸酯(2,4-TDI)与丙烯酸羟乙酯(HEA)封端反应生成丙烯酸基单异氰酸酯(IPT)为二级反应。同样,ITP与蓖麻油(CAO)扩链反应亦为二级。通过对缩合反应速率常数和表观活化能的研究表明:VTPU的结构主要由2,4-TDI中对位和邻位二异氰酸基的活性差异所控制,而齐聚物表观粘度与二异氰酸酯的结构规整性有关。动态粘弹谱测试表明:当VTPU中硬链段含量为59%时,聚合物呈分相结构,抗张强度最高为18.2MPa,若增加至67%时,在100.7℃呈现单一转变峰,动态模量因而下降。     

硬脂酸/异氰酸酯摩尔比对聚丙烯/木粉复合材料性能的影响

用甲苯-2,4-二异氰酸酯（TDI）和硬脂酸（SA）复合改性木粉,在双螺杆挤出机中制备了聚丙烯（PP）基的木塑复合材料（WPC）,研究了SA/TDI摩尔比对木粉表面性能、复合材料力学性能和加工性能的影响。 结果表明,随着SA/TDI摩尔比的增大,改性木粉的表面张力逐渐减小,与PP的界面张力先减小后增大;与未改性的WPC相比,SA/TDI复合改性剂对WPC的拉伸强度、弯曲强度、缺口冲击强度影响不明显,但对无缺口冲击强度提升较大;当SA/TDI摩尔比为1.07时,复合材料的无缺口冲击强度和熔体质量流动速率分别达到9.74 kJ/m2和13.12 g/10 min,分别比未改性WPC提高了77%和22%。     

木材溶液中羟基与异氰酸酯反应的研究

以涂料工业广泛应用的新型助剂二元酸酯 (DBE)为液化试剂 ,盐酸为催化剂 ,将苯甲基化木材溶液化后 ,与不同结构的异氰酸酯反应 .利用FT IR及1 3C NMR分析液化苯甲基木质纤维素与不同结构异氰酸酯得到了聚氨酯树脂 ,证明了木材中羟基可以用来作为聚醚多元醇与异氰酸酯制备聚氨酯材料 .通过准确测量体系中游离的NCO含量 ,从而得出不同结构异氰酸酯与木材溶液中羟基的反应规律 .实验结果表明 ,异氰酸酯的存在大大促进了木材结构中羟基的释放 ,由于不同异氰酸酯的活性不同 ,使得羟基值变化亦不相同 ,其顺序为IPDI>HDI>TDI .为了保证最终的材料性能 ,选择TDI和IPDI作为木材溶液制备聚氨酯树脂的异氰酸酯组份较好     

生漆与二异氰酸酯的反应及漆膜性能

本文用红外光谱（IR）、动态机械热分析（DMTA）、扫描电镜等仪器和物理、化学手段,研究生漆和2,4-甲苯二异氰酸酯（TDI）的反应特性、聚合成膜机理及漆膜性能等。结果表明,在漆酶和TDI共同作用下,生漆／TDI混合物的固化成膜速率比生漆快得多。当生漆与TDI混合后,生漆乳液的连续相中的漆酚迅速与TDI发生加成反应并生成聚氨酯化合物;在漆酶的催化作用下,该化合物的漆酚基上不饱和侧链双键进一步发生氧化聚合;所得的生漆／TDI涂膜具有优良的物理机械性能。     

Mechanical and thermal properties of attapulgite clay reinforced polymethylmethacrylate nanocomposites

To investigate the dispersion and nanofillers' interaction of rod‐like silicates (attapulgite, ATT) in the polymethylmethacrylate (PMMA) matrix, a novel in situ modification of ATT by toluene‐2,4‐di‐isocyanate (TDI) using mechanical mixing was exploited, which resulted in homogeneous dispersion and rod‐like texture of ATT nanorods. As a consequence, organo‐modified ATT/PMMA nanocomposites were prepared, which provided prominent improvements in strength, toughness, and thermal stability. High grafting efficiency of TDI on ATT surface was confirmed by FTIR spectra and SEM observations. The uniform dispersion of in situ TDI modified ATT nanorods in the PMMA which was clearly visible in the TEM micrographs, influenced the mechanical and thermal properties of the nanocomposites. The fibrous nanoparticles significantly confined the segmental motion, causing a 13.20°C increase in the glass transition temperature of 2 wt% in situ TDI modified ATT/PMMA nanocomposites. But at higher loadings little or no differences were observed for the reinforcement benefits provided by the in situ TDI modified ATT clay. By comparison, pre‐treated ATT clay severely fractured during mechanical mixing and showed little reinforcement benefits. Copyright © 2010 John Wiley & Sons, Ltd.     

丙烯酸酯单体修饰二氧化硅纳米粒子的制备

采用两步法将可聚合的乙烯基单体键接到S iO2纳米粒子表面合成了大分子单体.首先利用过量的甲苯-2,4-二异氰酸酯(TD I)对S iO2粒子表面进行化学修饰合成出表面带有高反应活性-NCO基团的功能化S iO2粒子(S iO2-TD I),再利用S iO2-TD I与丙烯酸羟丙酯(HPA)反应将碳-碳双键引入到S iO2粒子表面.系统考察了反应条件对TD I与S iO2反应的影响.此外,利用红外光谱和透射电镜对大分子单体进行表征,结果表明S iO2大分子单体能均匀地分散在甲苯中,没有发生明显团聚.     

SiO2大分子单体的合成

SiO2大分子单体的合成;SiO2;甲苯二异氰酸酯;表面修饰;二氧化硅大分子单体     

Synthesis and characterization of water-borne diisocyanate crosslinkers from methyl ethyl ketoxime/2-methylimidazole-blocked aromatic isocyanates

Water-borne blocked isocyanates (WBIs) were synthesized using toluene 2,4-diisocyanate (TDI), trimethylolpropane, dimethylolpropionic acid, 2-methylimidazole (2-MI), and methyl ethyl ketoxime (MEKO). The particle size, viscosity, pH, and storage stability of the WBI dispersions were studied and compared. De-blocking temperatures of the WBIs were characterized by Fourier transform infrared (FT-IR), differential scanning calorimetry (DSC), and thermo-gravimetric analysis (TGA) techniques. The thermal analysis revealed that MEKO-blocked TDI adducts and 2-MI-blocked TDI adducts started to de-block at about 70.7 and 125.2 °C, respectively. The storage stability results showed that all dispersions prepared were stable for more than 6 months. The dispersions prepared were all in liquid form and miscible (compatible) with acrylic dispersion. Gelation test results confirmed that MEKO-blocked isocyanate adducts dispersions de-block at higher temperatures and cure at faster rates than 2-MI-blocked isocyanate adducts dispersions. These anionically modified blocked isocyanate adducts can be used as potential crosslinkers.     

Synthesis and characterizations of poly(ethylene oxide) methyl ether grafted on the expanded graphite with isocyanate groups

Introducing isocyanate (NCO) groups onto the surface of expanded graphite (EG) was achieved by treatment of the EG with excess toluene-2,4-diisocyanate in dimethyl sulfoxide (DMSO). The reaction of NCO group on the EG with the hydroxyl group in the poly(ethylene oxide) methyl ether (MPEO) to yield MPEO-grafted EG was carried out for modifying the surface properties of graphite. The influence factors, such as reaction time, temperature and the ratio of the reactants, on the grafting reaction and grafting ratio were investigated.     

紫外辐射接枝法修饰聚乳酸表面及其细胞相容性

通过紫外辐射接枝在聚乳酸膜表面引入聚丙烯酸的方法使聚乳酸材料表面的亲水性和细胞相容性得到改善,研究了各种处理条件对材料表面的羧基密度、表面形态和表面接触角的影响,同时还考察了紫外辐射接枝聚丙烯酸的聚乳酸表面的成骨细胞相容性.红外光谱分析和羧基密度测定结果表明:通过紫外光引发接枝,聚丙烯酸被成功接枝到聚乳酸表面,而且接枝密度受接枝时间和聚丙烯酸质量分数的影响很大.接触角和原子力显微镜研究结果表明:接枝聚丙烯酸后的聚乳酸表面的亲水性和粗糙度明显增加,能够促进成骨细胞的生长.     

Surface modification of polymers. I. Vapour phase photografting with acrylic acid

Surfaces of low density polyethylene, high density polyethylene, and polystyrene have been modified by grafting with acrylic acid. Benzophenone and acrylic acid in the vapor phase were UV-irradiated in the presence of a polymer substrate. Grafting with acrylic acid took place in a thin layer on the surface, thus increasing the wettability of the polymer. After 5 min of irradiation, the contact angle against water had decreased to 20° for polystyrene and 50° for the polyethylene samples. ESCA measurements on samples irradiated for 5 min showed a 90% poly(acrylic acid) coverage of the surface for polystyrene, 63% for low density polyethylene, and 56% for high density polyethylene. Acetone or ethanol were used as carriers of monomer and initiator. Acetone was able to initiate grafting and was found to promote and direct grafting to the surface. The stability of the acrylic acid grafted surfaces was studied by contact angle measurements and ESCA. At room temperature, the grafted layer is confined to the surface, but when the material was heated in air the surface was reshaped into a hydrophobic one. The process was reversible. In aqueous surroundings at elevated temperatures the hydrophilic character of the surface was restored.     

生物芯片表面氨基硅烷化修饰

本文以无水乙醇为溶剂、3-氨基丙基三乙氧基硅烷(APTES)为修饰试剂、醋酸为催化剂,采用浸泡法,对生物芯片玻璃基片表面进行了氨基硅烷化修饰,得到了一种基片表面氨基修饰的制备方法。着重研究了制备过程中浸泡时间、APTES的浓度、酸处理的时间和羟基化的时间对基片噪声的影响。通过对以上工艺参数的逐步优化,基片噪声逐渐减小,最小值为193。通过对最佳修饰条件下得到的基片进行DNA点样和杂交测试可知,此方法制备得到的基片能够有效结合基因探针,且杂交清洗后信号强度可达17000以上,信噪比在110以上。由X射线光电子能谱分析可知,采用浸泡法可以获得表面氨基修饰的生物芯片基片。最后通过对修饰前后基片透过率的比较可知,修饰过程对透过率影响很小,且透过率在91%以上,从而保证了后续杂交信号与微阵列噪声检测的准确性。     

Surface Performance and Cytocompatibility Evaluation of Acrylic Acid-Mediated Carboxymethyl Chitosan Coating on Poly(tetrafluoroethylene-co-hexafluoropropylene)

To improve the biocompatibility of poly(tetrafluoroethylene-co-hexafluoropropylene) (FEP) film, a technique based on Ar plasma pretreatment and UV-induced grafting polymerization was used to immobilize carboxymethyl chitosan (CMCS) on the FEP film surfaces. Initially Ar plasma was used to treat FEP film. Then, plasma treated FEP film was modified via UV-induced grafting polymerization with hydrophilic acrylic acid (AAc) monomer. The following immobilization of CMCS on the FEP-pAAc surface was carried out via an amidation reaction. The change of chemical composition and surface morphology of FEP film were characterized by attenuated total reflectance Fourier transform infrared (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), scanning electronic microscopy (SEM) and atomic force microscopy (AFM). Results of water contact angles measurement showed that the hydrophilicity of the surface has improved significantly after surface modification. Furthermore, methyl thiazolyl tetrazolium (MTT) assay and cell morphology analysis confirmed that mouse fibroblasts (L929 cells) attachment and proliferation were improved remarkably on the modified FEP surface. These results suggest that CMCS were successfully employed to surface engineering FEP film, and enhanced its cell biocompatibility. The approach presented here may be exploited for surface modification of biomaterials.     

Grafting of Polymers onto Activated Carbon Surface: Graft Polymerization of Vinyl Monomers Initiated by Azo Groups That Were Introduced onto the Surface

Abstract

We examined the grafting of polymers onto an activated carbon powder surface by polymerization that was initiated by azo groups that were introduced onto the surface as well as the effects of grafted polymers on the adsorption of acetic acid. The introduction of azo groups onto the surface was achieved by the following methods: (1) a reaction of 4,4′-azobis(4-cyano-pentanoic acid) (ACPA) with surface isocyanate groups that were introduced beforehand by treatment with tolylene 2,4-diisocyanate (AC-Azo 1) and (2) the direct condensation of ACPA with surface phenolic hydroxyl groups by using N,N'-dicyclohexylcarbodiimide (AC-Azo 2). The radical polymerizations of styrene, methyl methacrylate, N,N-diethylacrylamide (DEAM), and N-isopropylacrylamide (NIPAM), were successfully initiated by the azo groups on the surface and the corresponding polymers were grafted onto the surface. There was a significant decrease in the adsorption of the acetic acid of the activated carbons when polymers were grafted onto them, particularly in regards to the grafting of hydrophobic polymers. On the other hand, a decrease in the adsorbability of the polyDEAM-grafted and polyNIPAM-grafted activated carbon was barely observed. In addition, polyDEAM-grafted and polyNIPAM-grafted activated carbons showed temperature-dependent adsorption of acetic acid: the adsorbability of these activated carbon decreased above lower critical solution temperature of these polymers, which is about 32°C.