Stereospecificity in Intramolecular Photoredox Reactions of Naphthoquinones: Enantioselective Total Synthesis of (−)‐Spiroxin C

Intramolecular photoredox reactions of naphthoquinone derivatives were found to proceed in a stereospecific manner. This method was used as a basis for the enantioselective total synthesis of (−)‐spiroxin C.     

A catalytic asymmetric entry to enantioenriched tertiary naphthoquinols via a facile tandem oxidation/ring-opening sequence

The tertiary naphthoquinol is a key structural component of the antitumor natural products spiroxins A-E. Herein we report the first catalytic asymmetric approach to the tertiary naphthoquinol C4′ stereogenic center present in the spiroxin framework, via tandem oxidation/ring-opening of a cyclic 3,4-epoxyalcohol. This new route allows a facile entry into relatively inaccessible tertiary naphthoquinols with high enantioselectivity and without the need of chiral auxiliaries.     

Fracture toughening of epoxy matrices with blends of resins of different molecular weights and other modifiers

The microstructure and fracture behavior of epoxy mixtures containing two monomers of different molecular weights were studied. The variation of the fracture toughness by the addition of other modifiers was also investigated. Several amounts of high‐molecular‐weight diglycidyl ether of bisphenol A (DGEBA) oligomer were added to a nearly pure DGEBA monomer. The mixtures were cured with an aromatic amine, showing phase separation after curing. The curing behavior of the epoxy mixtures was investigated with thermal measurements. A significant enhancement of the fracture toughness was accompanied by slight increases in both the rigidity and strength of the mixtures that corresponded to the content of the high‐molecular‐weight epoxy resin. Dynamic mechanical and atomic force microscopy measurements indicated that the generated two‐phase morphology was a function of the content of the epoxy resin added. The influence of the addition of an oligomer or a thermoplastic on the morphologies and mechanical properties of both epoxy‐containing mixtures was also investigated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3920–3933, 2004     

Synthesis and Characterization of Carbazole‐Linked Porphyrin Tweezers

Herein the synthesis, spectroscopic characterization, two‐photon absorption and electrochemical properties of 3,6‐disubstituted carbazole tweezers is reported. A dimer resulting from a Glaser homocoupling was isolated during a Sonogashira coupling reaction between a diethynyl‐carbazole spacer and a 5‐bromo‐triarylporphyrin and the properties of this original compound were compared with the 3,6‐disubstituted carbazole bisporphyrin tweezers. The dyads reported herein present a two‐photon absorption maximum at 920 nm with two‐photon absorption cross‐section in the 1200 GM range. Despite a strong linear absorption in the Soret region and moderate fluorescence quantum yield, they both lead to a high brightness reaching 30 000 M ^?1 cm^?1.     

Preparation of few‐layer two‐dimensional polymers by self‐assembly of bola‐amphiphilic small molecules

Two bola‐amphiphilic small molecules, based on the diphenylanthracene skeleton structure, namely, BASM‐1 and its functionalized small molecule BASM‐2 , were designed and synthesized. The self‐assembly behavior and mechanism of these two molecules in aqueous solution were studied. The supramolecular two‐dimensional (2D) layer and the covalent 2D polymers were, respectively, prepared by these two molecules. What is more, the transverse size of the covalent 2D polymer laminates increased with the extension of the polymerization time. Atomic force microscopy results showed that both free‐standing single‐layer 2D polymers and few layer laminates with two to three molecular layers were obtained. So our work provides a simple and efficient method for directly preparing independent both supramolecular 2D polymers and covalent 2D polymers in liquid phase which is of great significance. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1748–1755     

Topoisomerase I inhibitory and photocleavage activity of non‐dppz DNA ‘light switches’ based on ruthenium complexes containing nitro group

A new polypyridyl ligand containing a nitro group and two new ruthenium complexes of it were synthesized. The two complexes exhibited non‐dppz DNA ‘light switch’ effects after interaction with calf thymus DNA. Introducing both electron‐withdrawing group (─ NO₂) and electron‐donating group (─ CH₃) may be the reason that the two complexes display DNA ‘light switch’ behaviors. Furthermore, one of the complexes showed higher photocleavage activity, topoisomerase I inhibition activity and DNA affinity than the other. The present work shows that the more active complex can be employed as a non‐dppz DNA ‘light switch’, DNA photocleaver and topoisomerase I inhibitor. In addition, the two complexes have no or weak cytotoxic activities against Eca‐109 and A549 cells.     

Multiscale approach to investigate the radiochemical degradation of epoxy resins under high‐energy electron‐beam irradiation

A multiscale investigation of the degradation mechanism of two epoxy systems exposed to electron‐beam irradiation under a helium atmosphere was carried out with a variety of analytical methods, including high‐resolution solution‐ and solid‐state NMR spectroscopy, NMR relaxometry, infrared spectroscopy, sterical exclusion chromatography, and differential scanning calorimetry. As a first step, we studied a linear phenoxy polymer, poly(2‐hydroxyether of bisphenol A), which provided a basis for the investigation of the degradation of a more complex, insoluble epoxy–amine network, diglycidyl ether of bisphenol A/triethylene tetramine. Among different structural modifications, the main degradation process was shown to produce in both cases a chain scission. For the phenoxy resin, the hydroxypropylidene moiety was identified as the fragile site leading to the formation of two phenolic chain ends and acetone and isopropyl alcohol as low‐molecular‐weight products. All methods, ranging from molecular to supramolecular scales, were shown to correlate both qualitatively and quantitatively. Experimental results obtained with diglycidyl ether of bisphenol A/triethylene tetramine evidenced a different degradation scheme occurring at the ethylene amine part and producing a dangling vinyl amine as the major degradation product. A selective increase in the molecular mobility at this site was confirmed by a two‐dimensional, local‐field wide‐line separation experiment. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 865–887, 2006     

Aggregation‐Induced and Polymorphism‐Dependent Thermally Activated Delayed Fluorescence (TADF) Characteristics of an Oligothiophene: Applications in Time‐Dependent Live Cell Multicolour Imaging

Typically, molecules with a twisted donor–acceptor (D‐A) architecture have been exploited for constructing thermally activated delayed fluorescence (TADF) materials. Herein, we report the first example of a thiophene‐based thermally activated delayed fluorescent molecule without a D‐A architecture. Compound 1 (2,5‐bis(2,2‐di(thiophen‐2‐yl)vinyl)thiophene) is conformationally flexible and shows weak fluorescence in the solution state but displays bright TADFin both condensed and solid states. Compound 1 crystallized in two different polymorphs ( 1 a and 1 b ). Interestingly, both polymorphs show distinctly different TADF features. The broad spectral features and the TADF characteristics of 1 have been explored for the time‐dependent multicolor (green, yellow and red) imaging of living cells.     

Structural and Material Properties of Amyloid Aβ40/42 Fibrils

In this study, structural and mechanical properties of a series of models of Aβ₄₂ (one‐ and two‐fold) and Aβ₄₀ (two‐ and three‐fold) fibrils have been computed by using all‐atom molecular dynamics simulations. Based on calculations of the twist angle (θ) and periodicity (v=360d/θ), oligomers formed by 20, 11, and 13 monomers were found to be the smallest realistic models of three‐fold Aβ₄₀, one‐fold Aβ₄₂, and two‐fold Aβ₄₂ fibrils, respectively. Our results predict that the Aβ₄₀ fibrils initially exist in two staggered conformations [STAG(+2) and STAG(+1)] and then undergo a [STAG(+2)→STAG(+1)] transformation in a size‐dependent manner. The length of the loop region consisting of the residues 23–29 shrinks with the elongation of both Aβ₄₀ and Aβ₄₂ fibrils. A comparison of the computed potential energy suggests that a two‐fold Aβ₄₀ aggregate is more stable than its three‐fold counterpart, and that Aβ₄₂ oligomers can exist only in one‐fold conformation for aggregates of more than 11 monomers in length. The computed Young′s modulus and yield strengths of 50 GPa and 0.95 GPa, respectively, show that these aggregates possess excellent material properties.     

A low‐temperature polymorph of m‐quinquephenyl

A low‐temperature polymorph of 1,1′:3′,1′′:3′′,1′′′:3′′′,1′′′′‐quinquephenyl (m‐quinquephenyl), C₃₀H₂₂, crystallizes in the space group P2₁/c with two molecules in the asymmetric unit. The crystal is a three‐component nonmerohedral twin. A previously reported room‐temperature polymorph [Rabideau, Sygula, Dhar & Fronczek (1993). Chem. Commun. pp. 1795–1797] also crystallizes with two molecules in the asymmetric unit in the space group P. The unit‐cell volume for the low‐temperature polymorph is 4120.5 (4) ų, almost twice that of the room‐temperature polymorph which is 2102.3 (6) ų. The molecules in both structures adopt a U‐shaped conformation with similar geometric parameters. The structural packing is similar in both compounds, with the molecules lying in layers which stack perpendicular to the longest unit‐cell axis. The molecules pack alternately in the layers and in the stacked columns. In both polymorphs, the only interactions between the molecules which can stabilize the packing are very weak C—H...π interactions.     

Fabrication of Fluoropolymer Microtubes via RAFT Copolymerization of N,N′‐Methylene Bisacrylamide Gel Fibers and Fluoromonomer

Fluoropolymer microtubes with a smooth surface were fabricated in more than 70 % yield via reversible addition fragmentation chain transfer (RAFT) co‐polymerization of N,N′‐methylene bisacrylamide (MBA) gel fibers as both template and monomer, 2‐(perfluoro‐3‐methylbutyl)ethyl acrylate (R‐3420) as co‐monomer, and pentaerythritol tetraacrylate (PET4A) as cross‐linker. The resulting fluoropolymer microtubes were characterized fully by SEM, TEM, EDS, XPS, and FT‐IR. The influence of the monomer composition on the yields and morphologies of the tubes were investigated in detail. The results indicated that polymer microtubes with a smooth surface were obtained at suitable amounts of R‐3420 and PET4A. Because of the decreased solubility of MBA gel fibers, the wall thickness increased as more R‐3420 was used. In the presence of PET4A, the solution polymerization could be facilitated and more R‐3420 could be attached onto the tubes based on FT‐IR analysis. The water contact angle and swelling ratio measurements both revealed the low hydrophilicity and high lipophilicity of the fluoropolymer microtubes, which made the sample able to absorb toluene selectively in a water/toluene two‐phase system.     

Identification of very long chain fatty acids by atmospheric pressure chemical ionization liquid chromatography‐mass spectroscopy from green alga Chlorella kessleri

A method is described for the enrichment of very long chain fatty acids (VLCFAs) from total fatty acids of heterotrophically cultivated green freshwater alga Chlorella kessleri and their identification as picolinyl esters by means of liquid chromatography‐mass spectrometry with atmospheric pressure chemical ionization (LC‐MS with APCI). The method is based on the use of preparative reversed phase HPLC of hundred‐milligram amounts and their subsequent identification by microbore APCI LC‐MS. A combination of these two techniques was used to identify unusual VLCFAs up to C₄₇, both saturated and monounsaturated, with two positional isomers (ω‐9 and ω‐26).     

Effect of matrices and additives on phosphorylated and ketodeoxyoctonic acid lipids A analysis by matrix‐assisted laser desorption ionization‐mass spectrometry

Lipid A is a major compound of the outer membrane of gram‐negative bacteria and is a key factor of bacterial virulence. As lipid A's structure differs among bacterial species and varies between strains of the same species, knowing its modifications is essential to understand its implications in the infectious process. To analyze these lipids, matrix‐assisted laser desorption ionization‐mass spectrometry (MALDI‐MS) is a well‐suited method that is fast and efficient. However, there are limitations with the matrix and additives used, such as the suppression of signal or prompt fragmentations that could give a false overview of lipid A composition in biological samples. For a comprehensive analysis of the entire lipid A species present in a sample, we tested 16 matrices and 11 additives on two commercial lipids A. The first commercial one contains single phosphorylation group, and the second contains two phosphorylation and two ketodeoxyoctonic acid (KDO) groups. The lipid A containing KDO groups was essentially detected by the 3‐hydroxypicolinic acid (3‐HPA) matrix, whereas the monophosphorylated lipid A could be detected by 13 matrices out of the 16. We also demonstrated that the signal of diphosphorylated lipid A can be enhanced with the use of additives in the matrix. Our study indicated that the best conditions to obtain a clear signal of both lipids A without prompt fragmentation was the use of 3‐HPA with 10mM trifluoroacetic acid (TFA).     

Artificial Multienzyme Supramolecular Device: Highly Ordered Self‐Assembly of Oligomeric Enzymes In Vitro and In Vivo

A strategy for scaffold‐free self‐assembly of multiple oligomeric enzymes was developed by exploiting enzyme oligomerization and protein–protein interaction properties, and was tested both in vitro and in vivo. Octameric leucine dehydrogenase and dimeric formate dehydrogenase were fused to a PDZ (PSD95/Dlg1/zo‐1) domain and its ligand, respectively. The fusion proteins self‐assembled into extended supramolecular interaction networks. Scanning‐electron and atomic‐force microscopy showed that the assemblies assumed two‐dimensional layer‐like structures. A fluorescence complementation assay indicated that the assemblies were localized to the poles of cells. Moreover, both in vitro and in vivo assemblies showed higher NAD(H) recycling efficiency and structural stability than did unassembled structures when applied to a coenzyme recycling system. This work provides a novel method for developing artificial multienzyme supramolecular devices and for compartmentalizing metabolic enzyme cascades in living cells.     

Switchable thin‐film surface prepared via a simple grafting‐to method using a polystyrene‐b‐poly(2‐vinylpyridine) copolymer

A polystyrene‐b‐poly(2‐vinylpyridine) block copolymer containing a methylhydridosilane linking group was chemically grafted to an 8‐trichlorosilyloctene monolayer via a simple one‐step hydrosilylation reaction. The resulting Y‐shaped thin film exhibited a low grafting density, which was characteristic of the grafting‐to technique. To further reduce the miscibility of the two arms, methyl iodide was reacted with the poly(2‐vinylpyridine) block to produce quaternary ammonium groups. The surfaces before and after quaternization were both solvent‐switchable when subjected to block‐selective solvents. Tensiometry, ellipsometry, attenuated total reflection/Fourier transform infrared, and atomic force microscopy were used to characterize the properties and morphology of both unquaternized and quaternized samples. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5608–5617, 2006     

Total Synthesis of (−)‐Vindorosine

Outlined herein is a novel and scalable synthesis of (−)‐vindorosine based on two key transformations. A highly diastereoselective vinylogous Mannich addition of dioxinone‐derived lithium dienolates with indolyl N ‐tert‐butanesulfinyl imines has been developed. In addition, an intramolecular Heathcock/aza‐Prins cyclization was introduced to construct both the C, and the highly substituted E rings for the synthesis of (−)‐vindorosine and related alkaloids.     

Asymmetric Synthesis of Chiral 1,4‐Enynes through Organocatalytic Alkenylation of Propargyl Alcohols with Trialkenylboroxines

A highly enantioselective synthesis of 1,4‐enynes is described that proceeds through an organocatalytic reaction between propargyl alcohols and trialkenylboroxines. Our strategy relies on acid‐mediated generation of the carbocationic intermediate from propargyl alcohols followed by enantioselective alkenylation with trialkenylboroxines. A range of chiral 1,4‐enynes were obtained in moderate to good yields with high levels of enantioselectivity. Use of a highly acidic chiral N‐triflyl phosphoramide catalyst, which has two distant Lewis basic oxygen atoms, was found to be crucial for both high reactivity and selectivity in the present reaction.     

Anthracene and Anthraquinone Derivatives from the Stem Bark of Juglans mandshurica Maxim.

One new anthracene derivative, juglanthracenoside A ( 1 ), two new anthraquinones, juglanthraquinone A ( 2 ) and juglanthraquinone B ( 3 ), along with a new naturally occurring anthraquinone, 9,10‐dihydro‐4,8‐dihydroxy‐9,10‐dioxoanthracene‐2‐carboxylic acid ( 4 ), have been isolated from the stem bark of Juglans mandshurica. Their structures were established by detailed spectroscopic analysis and comparison of the NMR data with those of related compounds. Compound 1 displayed noticeable antioxidant activity in both 1,1‐diphenyl‐2‐picrylhydrazyl (DPPH) and 2,2′‐azinobis(3‐ethylbenzothiazoline‐6‐sulfonic acid) (ABTS) free radical‐scavenging assays, while compound 4 showed strong cytotoxicity against HepG2, SGC7901, HCT‐8, and A549 cell lines in vitro.     

A new crystal form of the NSAID dexketoprofen

Dexketoprofen [(2S)‐2‐(3‐benzoylphenyl)propanoic acid], C₁₆H₁₄O₃, is the S‐enantiomer of ketoprofen, a nonsteroidal anti‐inflammatory drug (NSAID) that has analgesic, antipyretic and anti‐inflammatory properties, and finds applications for the short‐term treatment of mild to moderate pain. A new crystalline phase of dexketoprofen is reported. Its solid‐state structure was determined by single‐crystal X‐ray diffraction (SCXRD). The molecular structure of the two independent molecules found in the asymmetric unit of this new phase ( DXKP‐β ) were compared to those of the already known crystal form of dexketoprofen ( DXKP‐α ) and with the S‐enantiomer of the racemic compound. The three different conformers of dexketoprofen found in DXKP‐α and DXKP‐β were then investigated by computational methods. The optimized structures are very close to the corresponding starting geometries and do not differ significantly in energy. The crystal packing of DXKP‐β was studied by means of Hirshfeld surface (HS) analysis; interaction energies were also calculated. A comparison with DXKP‐α shows close similarities between the two crystal forms, i.e. in both cases, molecules assemble through the catemer O—H…O synthon of the carboxylic acid stabilized by additional C—H…O contacts and, accordingly, the interaction energies, as well as the contributions to the HS area, are very similar. Finally, the thermal behaviour of the two polymorphs of dexketoprofen was assessed by means of XRD (both from single crystal and microcrystalline powder) and differential scanning calorimetry (DSC); both crystal forms are stable under the experimental conditions adopted (air, 300–350 K for DXKP‐α and 300–340 K DXKP‐β ) and no solid–solid phase transition occurs between the two crystal forms in the investigated temperature range (from 100 K up to ca 350 K).     

RP–HPLC–ESI–MS characterization of novel peptide fragments related to rat parotid secretory protein in parasympathetic induced saliva

Two peptides (MW 1211.7 and 928.5 Da) were detected by RP–HPLC–ESI–MS analysis of parotid saliva secreted upon continuous parasympathetic stimulation. The peptide with the higher mass (PSPFr‐A) corresponded to the N‐terminal dodecapeptide (Fragment 1–12) of rat parotid secretory protein (PSP), while the peptide with the lower mass (PSPFr‐B) corresponded to the 4–12 fragment of the same protein. During stimulation, the PSPFr‐A secretion increased, while the PSPFr‐B secretion decreased (HPLC–ESI–MS). In the presence of cycloheximide, PSPFr‐A was not demonstrated, while the PSPFr‐B secretion decreased. In the presence of aprotinin, the PSPFr‐B secretion was almost abolished, while the PSPFr‐A secretion increased to higher levels than those observed in the absence of the inhibitor. In vitro perfusion, with artificial solution, of stimulated rat parotid glands excluded that the fragments were derived from the circulation. Neither peptide occurred in enriched granule preparations from unstimulated glands. The results suggest that at least two pathways – granular and vesicular – are responsible for the generation of the two peptides. PSPFr‐A is the first cleavage product in both pathways. PRPFr‐B is probably generated from granular PSPFr‐A only and, at the end of the granule mediated pathway, by the action of an enzyme of the serine protease class.