蜂蜜含糖量的高效毛细管电泳测定研究

利用自制的毛细管电泳－电化学安培检测装置，以铜电极为工作电极，在氢氧化钠介质中，分别对２种蜂蜜样品中的糖类化合物进行分离检测，结果满意。     

毛细管电泳-钴钛菁碳糊修饰电极电化学催化氧化测定羟胺和巯基类化合物

本文利用自制的毛细管电泳－电化学安培检测装置，以钴钛菁碳糊修饰电极为工作。电极，在中性磷酸体系缓冲溶液中，对四种羟胺和巯基类化合物的混合物进行了分离和测定，检测下限羟胺类化合物为５．０×１０－６ｍｏｌ／Ｌ巯基类化合物为１．０×１０－５ｍｏｌ／Ｌ。对实际尿样中的半胱氨酸进行检测，结果满意。     

三种维生素的毛细管电泳和胶束电动毛细管色谱法分离与安培电化学检测

以自制毛细管电泳－电化学检测系统对ＶＣ,ＶＢ１和ＶＢ６的毛细管区带电泳和胶束电动色谱的分离与检测情况进行了初探。结果表明,在０．０１ｍｏｌ／ＬＮＨ３－ＮＨ４Ｃｌ介质中,检测电势定于５１０～５４０ｍＶ（对ＳＣＥ）时,三种维生素均有较好的ＣＺＥ图,对ＶＣ的分离效率达４６８８００块理论板。使用十二烷基硫酸钠时,分离效果欠佳。     

毛细管电泳—钴钛菁碳糊修饰电极电化学催化氧化测定羟胺和巯基类…

本文利用自制的毛细管电泳－电化学安培检测装置，以钴钛菁碳糊修饰电极为工作电极。在中性磷酸体系缓冲溶液中，对四种羟胺和巯基类化合物的混合物进行了分离和测定，检测下限羟胺类化合物为５．０×１０＾－６ｍｏｌ／Ｌ巯基类化合物为１．０×１０＾－５ｍｏｌ／Ｌ。对     

毛细管区带电泳电化学检测法测定药物及果汁中芦丁和L— …

用毛细管区带电泳－电化学检支同时测定复方芦丁片及果汁中芦丁和Ｌ－抗坏血酸的含量。研究了电极电位、电解液浓度和酸度、电泳电压及进样时间等对电泳的影响,得到了较为优化的测定条件。以直径为３００ｕｍ的碳圆盘电极为检测电极,电极电位为１．０Ｖ（υｓ．ＳＣＥ）,在２５０ｍｍｏｌ／Ｌ硼砂－５０ｍｍｏｌ／Ｌ ＮａＨ２ＰＯ４（ｐＨ ８．０）运行缓冲液中,上述两组分在１２ｍｉｎ内完全分离。芦丁和Ｌ－抗坏血酸浓度分别     

新型安培检测毛细管电泳微系统

将电极、６ｃｍ分离毛细管、缓冲池、检测池集成于８．４×５．０ｃｍ有机玻璃片上,制作了一个毛细管电泳微系统。以碳纤维微盘电极作为工作电极,采用三电极体系柱端检测了１×１０－４ｍｏｌ／Ｌ多巴胺（ＤＡ）,具有良好的重现性,检测限３．６×１０－８ ｍｏｌ／Ｌ,线性范围５×１０－７～１×１０－４ｍｏｌ／Ｌ,并在该系统上分离了邻苯二酚（ＣＡ）和多巴胺的混合物。     

烟草中糖类物质的高效毛细管电泳-安培检测研究

将高效毛细管电泳－安培检测技术（ＨＰＣＥ－ＡＤ）用于不同烟草样品中糖类物质的测定。在 １×１０－６ｍｏｌ／Ｌ～１×１０－３ ｍｏｌ／Ｌ范围内,存在良好的线性关系,葡萄糖、果糖、蔗糖和麦牙糖的检测限均小于 ５．０ ×１０－７ｍｏｌ／Ｌ,结果令人满意。     

牛膝多糖中单糖组分的毛细管电泳-电化学检测方法研究

利用毛细管电泳－电化学检测技术（CE－EC）对牛膝多糖水解液中的单糖进行了分离测定,证实牛膝多糖的化学组成中主要有葡萄糖、甘露糖和果糖3种单糖组分,并对其含量进行了测定。讨论了工作电位、分离电压、缓冲液浓度等因素对分离检测的影响。     

高效毛细管电泳柱端安培检测异丙嗪

本文用高效毛细管区带电泳柱端安培检测了抗组胺药物特异丙嗪。讨论了缓冲溶液浓度，ｐＨ值对柱效的影响，为提高检测的重现性考察了电极的电化学处理条件。在优化的实验条件下，异丙嗪的线性范围为１．×１０＾－７－１×１０＾－４ｍｏｌ／Ｌ，检测下限为３．５×１０＾－８ｍｏｌ／Ｌ，分离并检测了尿样中的１×１０＾－７ｍｏｌ／Ｌ的异丙嗪。     

集成芯片毛细管电泳电化学检测系统

研制了一种新颖的集成芯片毛细管电泳电化学检测装置。此装置基于柱末安培检测法，将检测池集成芯片上，以自制的30μmPt微盘电极为工作电极，在几十年秒钟内实现了多巴胺、5－羟色胺和肾上腺素三种神经递质的快速分离检测。     

在L-缬氨酸介质中应用聚二苯并-18-冠醚-6-分离铈（III)

 A column chromatographic method has been developed for the separation and determination of cerium(Ⅲ) using poly［dibenzo-18-crown-6］. The separation was carried out in L-valine medium. The adsorption of cerium(Ⅲ) was quantitative from 1×10-1 to 1×10-4 mol/L L-valine. Amongst the various eluents, 1.0-8.0 mol/L hydrochloric acid, 1.0-8.0 mol/L hydrobromic acid, 1.0-8.0 mol/L perchloric acid, 1.0-2.0 mol/L sulfuric acid and 4.0-5.0 mol/L acetic acid, were found to be the efficient eluents for cerium(Ⅲ). The capacity of poly［dibenzo-18-crown-6］ for cerium(Ⅲ) was （0.428±0.01） mmol/g. The method was applied to the separation of cerium(Ⅲ) from associated elements link uranium(Ⅵ) and thorium(Ⅳ). It was also applied for the determination of cerium(Ⅲ) in geological samples. The method is simple, rapid and selective with good reproducibility (approximately±2%).     

Chromatographic separation of cerium(Ⅲ) in L-valine medium using poly[dibenzo-18-crown-6]

A column chromatographic method has been developed for the separation and determination of cerium(Ⅲ) using poly[dibenzo-18-crown-6]. The separation was carried out in L-valine medium. The adsorption of cerium(Ⅲ) was quantitative from 1×10-1 to 1×10-4 mol/L L-valine. Amongst the various eluents, 1.0-8.0 mol/L hydrochloric acid, 1.0-8.0 mol/L hydrobromic acid, 1.0-8.0 mol/L perchloric acid, 1.0-2.0 mol/L sulfuric acid and 4.0-5.0 mol/L acetic acid, were found to be the efficient eluents for cerium(Ⅲ). The capacity of poly[dibenzo-18-crown-6] for cerium(Ⅲ) was (0.428±0.01) mmol/g. The method was applied to the separation of cerium(Ⅲ) from associated elements link uranium(Ⅵ) and thorium(Ⅳ). It was also applied for the determination of cerium(Ⅲ) in geological samples. The method is simple, rapid and selective with good reproducibility (approximately±2% ).     

Determination of benzene in soft drinks and other beverages by isotope dilution headspace gas chromatography/mass spectrometry

An automated, simple, and reproducible method was developed for the determination of benzene in soft drinks, based on isotope dilution headspace gas chromatography/mass spectrometry in the selected-ion monitoring mode. The method was used to assess benzene levels in samples of 124 soft drinks and beverages. Benzene was not detected in 60% of the 124 products. The average benzene levels in 6 products exceeded the Canadian maximum acceptable concentration of 5 microg/L for benzene in drinking water, and 2 of the 6 products had benzene levels above the World Health Organization guideline of 10 microg/L. The highest level of benzene, 23 microg/L, was found in a soft drink product specifically marketed to children.     

不完全抑制电导检测离子色谱法测定饮料中的苹果酸

采用一种抑制型离子色谱检测技术－－不完全抑制电导检测,以０．７５ｍｍｏｌ／ＬＮａ２ＳＯ４＋ＮａＯＨ（ｐＨ＝１１．５）为淋洗液对弱酸根离子如苹果酸、酒石酸等进行了测定,得到苹果酸、酒石酸的检测限分别为１．３１ｍｇ／Ｌ、３．０４ｍｇ／Ｌ;在２００ｍｇ／Ｌ以下相关系数分别为０．９９９８、０．９９９９;;各离子峰高的相对标准偏差（ＲＳＤ）分别为０．５７％、１．６０％。上率为９７．７￣１０４％。常见的强酸离     

液相色谱串联质谱法测定冷冻饮品中环己基氨基磺酸钠

建立了液相色谱～串联质谱测定冷冻饮品中环己基氨基磺酸钠的方法。冷冻饮品经净化、冷冻离心后用水稀释定容,采用C18色谱柱（50mm×2．1mm,1．7μm）,以乙腈-0．01mol／L乙酸铵缓冲溶液为流动相,电喷雾离子源负离子模式（MRM）定性、定量测定环己基氨基磺酸钠。环己基氨基磺酸钠的质量浓度在2—1000μg／L范围内与峰面积呈线性关系,相关系数,=0．9999,方法的定量限为0．02mg／kg。在10—100μg／L范围内,3水平加标回收率为87．5％～101．8％,测定结果的相对标准偏差为3．0％（H=6）。该方法净化效果好,灵敏度高,能快速完成冷冻饮品中环己基氨基磺酸钠的测定。     

Capillary electrophoretic determination of dithiocarbamates and ethyl xanthate

A simple and sensitive capillary electrophoretic method was developed for the separation and determination of sodium methyldithiocarbamate (metham), manganese ethylenebisdithiocarbamate (maneb) and ethyl xanthate in boric acid buffer by direct UV absorbance detection at lambda = 254 nm. The separation is dependent on pH and nature of the buffer. The detection limits (S/N = 3) are 1.7 x 10(-6) mol/L for ethyl xanthate, 1.3 x 10(-6) mol/L for metham and 2.1 x 10(-6) mol/L for maneb. The method has been successfully applied to the analysis of wheat samples spiked with maneb and in a commercial sample.     

Direct determination of amino acids by pressurized capillary electrochromatography with chemiluminescence detection

A pressurized CEC (pCEC) coupled with on-column chemiluminescence (CL) detection was developed for direct determination of amino acids, which was based on the principle of an enhanced effect of Cu(II)-amino acid complexes on the CL reaction between luminol and hydrogen peroxide in alkaline solution. The effects of some important factors on pCEC separation and CL intensity were systemically investigated. Baseline separation of amino acids including L-histidine (L-His), L-threonine (L-Thr), and L-tyrosine (L-Tyr) was achieved by using a monolithic column with a mobile phase of 5.0x10(-3) mol/L phosphate buffer at pH 8.0 that contained 25% v/v methanol and 5.0x10(-4) mol/L luminol and 1.0x10(-5) mol/L Cu(II) at an applied voltage of -5 kV. The calibration curves of the analytes by plotting the peak height against corresponding concentration were linear over the range of 3.2x10(-6)-3.2x10(-4) mol/L for L-His, 4.1x10(-6)-4.1x10(-4) mol/L for L-Thr, and 6.0x10(-7)-3.0x10(-4) mol/L for L-Tyr. The LODs for L-His, L-Thr, and L-Tyr were 6.4x10(-7), 8.4x10(-7), and 3.0x10(-7) mol/L (S/N = 2), respectively. The proposed method was applied to the analysis of amino acid injection sample with satisfactory results. Mean recoveries for three amino acids were from 84.3 to 89.6%.     

Analysis of organic acids and inorganic anions in beverage drinks by capillary electrophoresis

To meet the need for a new and validated analytical method for simultaneous determination of inorganic and organic acid anions in beverage drinks, a capillary zone electrophoresis (CZE) procedure had been developed based on a new background electrolyte (BGE) system containing 3 mmol/L 1,3,5-benzenetricarboxylic acid (BTA), 15 mmol/L tris(hydroxymethyl)aminomethane and 1.5 mmol/L tetraethylenepentamine (TEPA) at pH 8.4. Baseline separation of anions commonly found in beverage drinks could be achieved in less than 14 min with indirect UV detection at 240 nm. Comigration problems for hydroxycarboxylic acids could be solved using TEPA as BGE additive. The results indicate excellent repeatability for migration time (RSD, 0.27-0.67%, n = 5) and good precision for both peak height (RSD, 3.2-4.2%, n = 5) and peak area (RSD, 3.1-4.5%, n = 5). Under the optimized conditions and using corrected peak area for quantitation, an excellent linear dynamic range (with correlation coefficient > 0.997 in a concentration range from 0.005 to 2.0 mmol/L) and low detection limit (1-4 micro mol/L) were obtained for all the anions investigated. The applicability and reliability of the CE procedure developed were established by parallel method determination using established ion chromatography procedure for the analysis of inorganic and organic acid anions in orange juice and wine samples. Our CZE procedure provided a sensitive and economic technique for simultaneous determination of inorganic and organic acid anions in orange juice, red and white wine samples.     

Simultaneous determination of dihydroxybenzene positional isomers by capillary electrochromatography using gold nanoparticles as stationary phase

The paper describes the enhanced separation of o-, m-, p-dihydroxybenzene by capillary electrochromatography (CEC) using gold nanoparticles (AuNPs) as stationary phase. The effect of the AuNPs concentration upon separation was investigated. The experimental parameters, including separation voltage, pH, and concentration of running buffer, were optimized. Under the optimum conditions, a good resolution of three dihydroxybenzene isomers was obtained within 15 min in a 50 cm effective length capillary modified with 0.02 nmol/L AuNPs at a separation voltage of 16 kV in a 50 mmol/L acetate buffer (pH 5.0). The linear ranges were from 10(-6) to 10(-4) mol/L and the detection limits were as low as 10(-7) mol/L. This method was successfully used to analysis two kinds of hair coloring agent sample with recoveries in the range of 90-105% and relative standard deviations (RSD) less than 5.0%.     

Direct electrochemical determination of pyruvate in human sweat by capillary zone electrophoresis.

Capillary zone electrophoresis was employed for the determination of pyruvate in human sweat using electrochemical detection with a carbon fiber microdisk bundle electrode at a constant potential of 1.60 V vs. saturated calomel electrode. The optimum separation conditions are 3.6 x 10(-3) mol/L Na2HPO4-1.4 x 10(-3) mol/L NaH2PO4 (pH 7.2) for the buffer solution, and 18 kV for the separation voltage. The limits of detection of pyruvate are 8.0 x 10(-6) mol/L or 24 fmol (S/N = 3) for the injection voltage of 6 kV and the injection time of 10 s. The relative standard deviation is 2.0% for the migration time and 5.7% for the electrophoretic peak current. The method was applied to determining pyruvate in human sweat.