Tunable optical stop band of silica shell photonic crystals

In this study, optical stop band of three-dimensional silica shell photonic crystals is tuned by adjusting inner diameter and shell thickness of hollow silica spheres. The silica shell photonic crystals are fabricated by sintering crystalline arrays, which are assembled from polystyrene/silica core–shell spheres by an improved vertical deposition method. The inner diameter and the shell thickness are controlled by diameter of polystyrene spheres and concentration of tetraethoxysilane. The results of transmission spectra show that there is an evident red shift of optical stop band as the inner diameter and the shell thickness increase. The red shift of optical stop band is due to variations in the inter-planar spacing and the effective refractive index of silica shell photonic crystals, which result from the variations of the inner diameter and the shell thickness of hollow silica spheres.     

The formation of mesoporous TiO2 spheres via a facile chemical process

The mesoporous TiO(2) solid and hollow spheres have been synthesized via a controllable and simple chemical route. Structural characterization indicates that these TiO(2) mesoporous spheres after calcined at 500 degrees C have an obvious mesoporous structure with the diameters of 200-300 nm for solid spheres and 200-500 nm for hollow spheres. The average pore sizes and BET surface areas of the mesoporous TiO(2) solid and hollow spheres are 6.8, 7.0 nm and 162, 90 m(2)/g, respectively. Optical adsorption investigation shows that TiO(2) solid and hollow spheres possess a direct band gap structure with the optical band gap of 3.68 and 3.75 eV, respectively. A possible formation mechanism for TiO(2) solid and hollow spheres is discussed.     

TiO2/SnO2复合空心球在染料敏化太阳能电池中的应用

采用模板辅助法制备了SnO2/TiO2复合空心球,样品直径为1.5~4.0μm,比表面积达到了92.9 m^2·g^-1,复合空心球表现出优越的光散射性能.以这种复合空心球作为染料敏化太阳能电池的光阳极,电池的光电转换效率可达到7.72%,高于SnO2微米球(2.70%)和TiO2微米球(6.26%).此外,以锐钛矿型TiO2纳米晶作为底层,SnO2/TiO2复合空心球作为光散射层制备的双层结构光阳极,电池光电转换效率进一步提升至8.43%.     

中空TiO_2微球的制备及对聚丙烯酸酯薄膜性能的影响

采用阳离子聚苯乙烯微球作为模板,钛酸四丁酯为钛源,氨水为催化剂,制备了中空TiO_2微球.采用X射线衍射、扫描电镜及比表面测定仪对其形貌和结构进行了表征,并考察了模板粒径、钛源用量以及催化剂用量对中空TiO_2微球形貌的影响.通过物理共混法将其引入至聚丙烯酸酯乳液中并成膜,研究了复合薄膜的保温性能、抗紫外性能及力学性能.结果表明,锐钛矿相中空TiO_2微球模板粒径、钛源用量以及催化剂用量影响中空TiO_2微球的空心尺寸、壁厚及壳层致密性.中空TiO_2微球可显著提升聚丙烯酸酯薄膜的保温性能、抗紫外性能和力学性能.采用不同粒径的模板制备的中空TiO_2微球对复合薄膜的各项性能均有影响,其中模板粒径为140 nm时复合薄膜性能最优,光反射率提升63%,导热系数降低27%,且在波长小于360 nm范围内,紫外透过率几乎为0,抗张强度增加100%,断裂伸长率提升62%.     

Single-crystalline rutile TiO2 hollow spheres: room-temperature synthesis, tailored visible-light-extinction, and effective scattering layer for quantum dot-sensitized solar cells

A general synthesis of inorganic single-crystalline hollow spheres has been achieved through a mechanism analogous to the Kirkendall effect, based on a simple one-step laser process performed at room temperature. Taking TiO(2) as an example, we describe the laser process by investigating the influence of experimental parameters, for example, laser wavelength, laser fluence/irradiation time, liquid medium, and concentration of starting materials, on the formation of hollow spheres. It was found that the size-tailored TiO(2) hollow spheres demonstrate tunable light scattering over a wide visible-light range. Inspired by the effect of light scattering, we introduced the TiO(2) hollow sphere's scattering layer in quantum dot-sensitized solar cells and achieved a current notable 10% improvement of solar-to-electric conversion efficiency, indicating that TiO(2) hollow spheres are potential candidates in optical and optoelectronic devices.     

Synthesis, characterization, and optical properties of well-defined N-doped, hollow silica/titania hybrid microspheres

Well-defined nitrogen-doped, hollow SiO2/TiO2 hybrid spheres were successfully prepared through a two-step sol-gel synthesis combined calcination process using triethylamine as the nitrogen source. In this approach, polystyrene (PS)/silica microspheres were first synthesized. Subsequently, the amine-treated PS/SiO2/TiO2 hybrid spheres were obtained by sol-gel method. Finally, the elimination of the PS core, nitrogen-doping process, and crystallization of amorphous TiO2 were simultaneously conducted in the calcination process to acquire the final products. The as-prepared hybrid spheres were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared (FTIR) spectroscopy. The results of XRD, FTIR, and XPS spectra indicated that nitrogen was really doped into the anatase TiO2 shell and confirmed that most nitrogen dopants might be present in the chemical environments of N-Ti-O and Ti-N-O. It was found that the absorption shoulder of nitrogen-doped hollow SiO2/TiO2 hybrid spheres vastly shifted to the visible region up to around 530 nm. The photoluminescence (PL) bands showed spectral lines at about 421, 472, and 529 nm, which were attributed to the self-trapped excitons, F and F+ centers. Moreover, the intensity of the PL spectra band of hollow SiO2/TiO2 hybrid spheres increased with as the amount of titanium tetrabutoxide (TBOT) precursor increased. However, the doping of nitrogen into hollow SiO2/TiO2 hybrid spheres led to the drastic quenching of photoluminescence because of the increase in the separation efficiency of the photoinduced electron and hole pairs.     

Effect of disorder on the optically amplified photocatalytic efficiency of titania inverse opals

Optically amplified photochemistry with slow photons has been realized in our previous work when a photoactive material such as TiO(2) was molded into a photonic crystal and the corresponding energy of photonic bands overlapped with the electronic excitation. While numerous applications of photonic crystals have been proposed, the real practicality depends on the extent of structural imperfection that can be tolerated before significant deterioration in the optical response deems it unrealistic to use. As a result, it is important to evaluate the amount of structural disorder that can be tolerated in inverse TiO(2) opals if they are to be used as amplified photocatalysts for photolytic degradation of organics in environmental remediation and water purification. We present a systematic study on the effect of disorder with relation to the photocatalytic efficiency of oxidizing methylene blue dye adsorbed on inverse TiO(2) opals by introducing different fractions and sizes of guest spheres into the opal template. Our results show that half of the enhancement originally achieved by the inverse opal made from monodispersed 150-nm spheres is conserved when the domain size of the host spheres remains above a critical threshold. The substitution fraction can be as high as 0.4 when the guest spheres are 1.2 times larger than the host spheres. Such a high tolerance to structural disorder provides strong support for the potential use of inverse TiO(2) opals in environmental cleanup and water treatment applications.     

Preparation, photocatalytic activities, and dye-sensitized solar-cell performance of submicron-scale TiO2 hollow spheres

We prepared submicron-scale spherical hollow particles of anatase TiO2 by using a polystyrene-bead template. The obtained particles were very uniform in size, with a diameter of 490 nm and a shell thickness of 30 nm. The Brunauer-Emmett-Teller surface area measurements revealed a large value of 70 m2/g. The photocatalytic property was investigated by the complete decomposition of gaseous isopropyl alcohol under UV irradiation. It was indicated that the activity of the hollow spheres was 1.8 times higher than that of the conventional P25 TiO2 nanoparticles with a diameter of 30 nm. Furthermore, we fabricated a dye-sensitized solar cell (DSC) using an electrode of the TiO2 hollow spheres, and examined the photovoltaic performance under simulated sunlight. Although the per-area efficiency was rather low (1.26%) because of a low area density of TiO2 on the electrode, the per-weight efficiency was 2.5 times higher than those of the conventional DSCs of TiO2.     

Standing wave enhancement of red absorbance and photocurrent in dye-sensitized titanium dioxide photoelectrodes coupled to photonic crystals

The light harvesting efficiency of dye-sensitized photoelectrodes was enhanced by coupling a TiO(2) photonic crystal layer to a conventional film of TiO(2) nanoparticles. In addition to acting as a dielectric mirror, the inverse opal photonic crystal caused a significant change in dye absorbance which depended on the position of the stop band. Absorbance was suppressed at wavelengths shorter than the stop band maximum and was enhanced at longer wavelengths. This effect arises from the slow group velocity of light in the vicinity of the stop band, and the consequent localization of light intensity in the voids (to the blue) or in the dye-sensitized TiO(2) (to the red) portions of the photonic crystal. By coupling a photonic crystal to a film of TiO(2) nanoparticles, the short circuit photocurrent efficiency across the visible spectrum (400-750 nm) could be increased by about 26%, relative to an ordinary dye-sensitized nanocrystalline TiO(2) photoelectrode.     

Ternary inverse opal system for convenient and reversible photonic bandgap tuning

A ternary system, consisting of air, an air-core/dense-silica-shell core-shell particle, and liquids has been used to fabricate an inverse opal structure with low fill factor, high refractive index contrast, and reversible tuning capabilities of the bandgap spectral position. The original close-packed opal structure is a ternary self-assembled photonic crystal from monodisperse and spherical polystyrene-core/silica-shell colloidal particles with air as the void material. Calcination removed the polystyrene and converted the core-shell particles to hollow spheres with a dense shell. In a final step, liquid is infiltrated only in the voids between the hollow spheres, but does not penetrate in the shell. This allows facile and reversible tuning of the bandgap properties in an inverse opal structure.     

TiO2 and SnO2@TiO2 hollow spheres assembled from anatase TiO2 nanosheets with enhanced lithium storage properties

TiO(2) and SnO(2)@TiO(2) hollow spheres assembled from anatase TiO(2) nanosheets with exposed (001) high-energy facets are constructed via a templating approach, and the as-prepared samples exhibit enhanced lithium storage properties.     

Nanoparticle self-assembled hollow TiO(2) spheres with well matching visible light scattering for high performance dye-sensitized solar cells

Submicrometer-sized hollow TiO(2) spheres are directly self-assembled from TiO(2) nanoparticles without using any template or surfactant as a scattering layer for dye-sensitized solar cells, showing good visible light scattering match to significantly improve the photoconversion efficiency.     

Opal and inverse opal photonic crystals: Fabrication and characterization

Three-dimensional photonic crystals made of close-packed polymethylmethacrylate (PMMA) spheres or air spheres in silica, titania and ceria matrices have been fabricated and characterized using SEM, XRD, Raman spectroscopy and UV–Vis transmittance measurements. The PMMA colloidal crystals (opals) were grown by self-assembly from aqueous suspensions of monodisperse PMMA spheres with diameters between 280 and 415 nm. SEM confirmed the PMMA spheres crystallized uniformly in a face-centred cubic (fcc) array, and UV–Vis measurements show that the colloidal crystals possess pseudo photonic band gaps in the visible and near-IR regions. Inverse opals were prepared by depositing silica (SiO₂), titania (TiO₂) or ceria (CeO₂) in the voids of the PMMA colloidal crystals using sol-gel procedures, then calcining the resulting structure at 550 °C to remove the polymer template. The resulting macroporous materials showed fcc ordering of air spheres separated by thin frameworks of amorphous silica, nanocrystalline titania or nanocrystalline ceria particles, respectively. Optical measurements confirmed the photonic nature of the inverse opal arrays. UV–Vis data collected for the opals and inverse opals obeyed a modified Bragg’s law expression that considers both diffraction and refraction of light by the photonic crystal architectures. The versatility of the colloidal crystal template approach for the fabrication of macroporous oxide structures is demonstrated.     

Fluorine ions-mediated morphology control of anatase TiO2 with enhanced photocatalytic activity

This review briefly summarizes recent advances in fluorine ions-mediated morphology control of anatase TiO(2) in the forms of nanotube arrays, nanosheets with high-energy facets, and hollow spheres. The correlations between the enhanced photocatalytic activity and structural and morphological modifications of anatase TiO(2) by fluorine ions are addressed.     

Increasing the conversion efficiency of dye-sensitized TiO2 photoelectrochemical cells by coupling to photonic crystals

The mechanism of enhancing the light harvesting efficiency of dye-sensitized TiO(2) solar cells by coupling TiO(2) inverse opals or disordered scattering layers to conventional nanocrystalline TiO(2) films has been investigated. Monochromatic incident photon-to-current conversion efficiency (IPCE) at dye-sensitized TiO(2) inverse opals of varying stop band wavelengths and at disordered titania films was compared to the IPCE at bilayers of these structures coupled to nanocrystalline TiO(2) films and to the IPCE at nanocrystalline TiO(2) electrodes. The results showed that the bilayer architecture, rather than enhanced light harvesting within the inverse opal structures, is responsible for the bulk of the gain in IPCE. Several mechanisms of light interaction in these structures, including localization of heavy photons near the edges of a photonic gap, Bragg diffraction in the periodic lattice, and multiple scattering events at disordered regions in the photonic crystal or at disordered films, lead ultimately to enhanced backscattering. This largely accounts for the enhanced light conversion efficiency in the red spectral range (600-750 nm), where the sensitizer is a poor absorber.     

In2O3/ZrO2-TiO2空心球复合材料的制备与光解水制氢性能

以聚苯乙烯(PS)胶球为模板, 通过一步法结合煅烧后处理制备了空心球复合材料In₂O₃/ZrO₂-TiO₂. 采用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 扫描电子显微镜(SEM)、 紫外-可见漫反射吸收光谱(UV-Vis DRS)和氮气吸附-脱附等测试手段对复合材料的结构、 组成和形貌进行了表征. 结果表明, In₂O₃/ZrO₂-TiO₂复合材料的晶型结构以锐钛矿型TiO₂为主, 同时存在少量含有Ti—O—Zr键的混合氧化物. 该复合材料经聚苯乙烯模板处理后呈现空心球状结构, 球壁由纳米粒子堆积而成. In₂O₃/ZrO₂-TiO₂空心球复合材料的比表面积较大(66.92 m²/g), 且In₂O₃与ZrO₂-TiO₂复合后光吸收发生了红移. 对该复合材料光解水制氢性能的研究结果表明, 空心球状In₂O₃/ZrO₂-TiO₂具有较好的产氢效果(56.7 μmol/g, 8 h), 明显高于P25、 ZrO₂、 空心球状ZrO₂-TiO₂及粉末状In₂O₃/ZrO₂-TiO₂.     

分级微纳结构TiO2空心球的制备及其在DSSC中的应用

以钛酸四丁酯为钛源,无水乙醇为溶剂,通过碳球模板法制备出直径为200nm、壳厚20～25nm的TiO2空心球（HS）.通过X射线衍射（XRD）、透射电子显微镜（TEM）、扫描电子显微镜（SEM）和N2吸附脱附等对产物的形貌、晶相组成、孔结构和紫外-可见光谱性质进行了表征,结果显示所制备的锐钛矿相TiO2空心微球是由初级结构纳米级TiO2晶粒构成的.将这种TiO2空心球应用于染料敏化太阳电池（DSSC）领域可以提高光阳极对光的散射.通过制备P25/HS-TiO2双层膜电极,相比单纯的P25纳米晶电极（Jsc=13.5mAcm？2,Voc=0.653V,FF=0.53,η=4.95%）可以得到更高的光电转化效率（Jsc=15.79mAcm？2,Voc=0.653V,FF=0.55,η=6.66%）.     

Large-scale fabrication of TiO2 hierarchical hollow spheres

In this Communication, we report the fabrication of well-crystallized rutile-phase TiO2 hollow spheres using potassium titanium oxalate as the precursor. The spheres exhibited unique three-dimensional hierarchical architectures and demonstrated a significantly improved photocatalytic performance. The synthetic strategy used in this process represents a general approach and therefore may contribute to the formation mechanisms of hollow nanostructures.     

Biomolecule-assisted route to prepare titania mesoporous hollow structures

Amino acids, as a particularly important type of biomolecules, have been used as multifunctional templates to intelligently construct mesoporous TiO(2) hollow structures through a simple solvothermal reaction. The structure-directing behaviors of various amino acids were systematically investigated, and it was found that these biomolecules possess the general capability to assist mesoporous TiO(2) hollow-sphere formation. At the same time, the nanostructures of the obtained TiO(2) are highly dependent on the isoelectric points (pI) of amino acids. Their molecular-structure variations can lead to pI differences and significantly influence the final TiO(2) morphologies. Higher-pI amino acids (e.g., L-lysine and L-arginine) have better structure-directing abilities to generate nanosheet-assembled hollow spheres and yolk/shell structures. The specific morphologies and mesopore size of these novel hollow structures can also be tuned by adjusting the titanium precursor concentration. Heat treatment in air and vacuum was further conducted to transform the as-prepared structures to porous nanoparticle-assembled hollow TiO(2) and TiO(2)/carbon nanocomposites, which may be potentially applied in the fields of photocatalysts, dye-sensitized solar cells, and Li batteries. This study provides some enlightenment on the design of novel templates by taking advantage of biomolecules.     

Synthesis and utilization of monodisperse hollow polymeric particles in photonic crystals

We developed a process to fabricate 150-700 nm monodisperse polymer particles with 100-500 nm hollow cores. These hollow particles were fabricated via dispersion polymerization to synthesize a polymer shell around monodisperse SiO(2) particles. The SiO(2) cores were then removed by HF etching to produce monodisperse hollow polymeric particle shells. The hollow core size and the polymer shell thickness, can be easily varied over significant size ranges. These hollow polymeric particles are sufficiently monodisperse that upon centrifugation from ethanol they form well-ordered close-packed colloidal crystals that diffract light. After the surfaces are functionalized with sulfonates, these particles self-assemble into crystalline colloidal arrays in deionized water. This synthetic method can also be used to create monodisperse particles with complex and unusual morphologies. For example, we synthesized hollow particles containing two concentric-independent, spherical polymer shells, and hollow silica particles which contain a central spherical silica core. In addition, these hollow spheres can be used as template microreactors. For example, we were able to fabricate monodisperse polymer spheres containing high concentrations of magnetic nanospheres formed by direct precipitation within the hollow cores.