PVC/ACR共混物微观结构与性能

本文研究了聚氯乙烯/丙烯酸酯类共聚物(PVC/ACR)共混物的应力-应变行为和冲击强度对ACR 用量的依赖关系。ACR对 PVC有良好的增韧作用,提高了PVC抗冲击性能。考察了三盐基性硫酸铅和硬脂酸钡-硬脂酸镉稳定剂对共混体系的影响,实验结果说明不同的热稳定体系对ACR改性PVC的效果有差别。动态力学性能测定结果表明PVC/ACR共混物存在两个玻璃化转变温度,证明PVC与ACR不相容性;而两个转变温度随共混物组成改变而变化,说明PVC与ACR之间存在着相互作用,PVC/ACR为部分相容体系。通过透射电子显微镜观察PVC/ACR共混物的微观结构形态表明:PVC与 ACR为两相体系,ACR呈粒状分布在PVC连续相中。但是,采用硬脂酸钡-硬脂酸镉稳定体系时,随着ACR用量增加,ACR的分散形态由粒状分散逐渐形成网络结构形态,与此相对应的共混物具有更好的抗冲击性能。     

聚氯乙烯／热塑性弹性体共混增韧的研究进展

聚氯乙烯（PVC）是一种性能优良,价格低廉的通用树脂,但其脆性大、热稳定性差、加工性能不佳等,需要进行改性。通过用热塑性弹性体（TPE）对PVC进行共混增韧改性,可得到高性能的PVC复合材料。共混改性为PVC增韧改性的最简单易行的有效方法。本文概述了聚氯乙烯／热塑性弹性体共混体系的种类和制备方法,同时对影响热塑性弹性体...     

刚性有机粒子对聚氯乙烯／氯化聚乙烯共混体系形态和增韧机理的研究

刚性有机粒子对聚氯乙烯／氯化聚乙烯共混体系形态和增韧机理的研究周丽玲，吴其晔，杨文君，刘士龙，张漫（青岛化工学院橡胶系青岛２６６０４２）关键词刚性有机填料，聚氯乙烯ＰＶＣ，氯化聚乙烯（ＣＰＥ）形态，增韧机理在共混改性中，弹性体增韧硬质聚氯乙烯（ｎｙＶ...     

纳米级CaCO_3粒子与弹性体CPE微粒同时增韧PVC的研究

研究了平均粒径为 30nm的超细级纳米CaCO3 与氯化聚乙烯 (CPE)对聚氯乙烯 (PVC)共混体系二元协同增韧效应及机制 .结果表明 ,当共混体系中有一定量的CPE时 ,纳米CaCO3 的加入可以明显地提高共混物的韧性 ,而不降低共混物的强度和刚性 .纳米CaCO3 在PVC基体中达到了纳米级的分散 .当纳米CaCO3 的用量为 8份 (质量 )时 ,PVC CPE 纳米CaCO3 共混物的冲击断面产生了大量的有规则的网丝状结构 ,共混物的缺口冲击强度达到 81 1kJ m2 ,比不加纳米CaCO3 的共混体系高 7 3倍 .CPE的加入对共混体系的加工流动性能无影响 ,纳米CaCO3 的加入使共混体系的加工流动性能变差     

超高分子量聚乙烯／聚丙烯共混体系流变行为及形态的研究

超高分子量聚乙烯／聚丙烯共混体系流变行为及形态的研究汪晓东,励杭泉,金日光（北京化工大学高分子系,北京,１０００２９）关键词共混合金,线性互穿网络,双连续相,网络增韧机理通常聚合物的增韧机理是在树脂中引人柔性链段［１］形成复合物（如橡塑共混物）,这些...     

橡胶增韧塑料机理的探讨

本实验采用透射电镜及新的ＲｕＯ_４染色方法，观察研究了ＰＣ／ＰＢＴ，ＰＣ／ＭＢＳ／ＰＳ共混体系和ＡＡＳ共聚共混物的银纹结构形态。结果表明：不同聚合物体系银纹产生的数量，银纹的发展、终止及支化各不相同。这时研究塑料增韧机理很有意义。     

共混方法对聚氯乙烯/聚丙撑碳酸酯相容性影响

本文分别用溶液法和熔融法制得聚氯乙烯（PVC）与聚丙撑碳酸酯（PPC）共混试样，用DSC证明PVC／PPC共混物不相容，但它们不相容的程度受分子量、共混比例等因素的影响，并根据玻璃化转变温度（Tg）计算出溶液共混试样PPC富相中PVC的重量百分含量。NBR／PPC弹性体作偶联剂对PVC／PPC共混体系具有较好的增容作用，共混物中PPC的用量及分子量对共混体系性能有一定的影响。     

弹性体偶联剂结构对PVC/PPC性能的影响

NBR－PPC弹性体偶联剂能促进PPC（聚丙撑碳酸酯）与PVC（聚氯乙烯）之间的相容性，改善共混物的力学性能，并在共混体系中产生轻度交联。偶联剂组成在NBR／PPC比例为70／30，NBR（丁腈橡胶）含腈量为34％，BPO过氧化苯甲酸用量为2．5份时，共混物的综合力学性能最佳，但偶联剂预先硫化时间不宜过长．     

高抗冲聚苯乙烯的增韧机理

概述了以高抗冲聚苯乙烯（ＨＩＰＳ）为中心的有关橡胶增韧机理的理论，并且总结了界面，性能、粒子尺寸、粒 距及缠结密度等因素对橡胶／高分子共混体系性能的影响。     

丁腈橡胶对聚甲醛树脂的增韧机理研究

研究了丁腈橡胶（ＮＢＲ） 对聚甲醛（ＰＯＭ） 树脂的增韧机理,并比较了ＰＯＭ／ＮＢＲ 体系和ＰＯＭ／ 热塑性聚氨酯（ＴＰＵ） 体系的异同．结果表明,高丙烯腈（ＡＮ） 含量的ＮＢＲ 有着和ＴＰＵ 相近的溶度积参数,且其分子上的氰（ＣＮ） 基或双键对ＰＯＭ 分解时产生的甲醛及大分子自由基的捕捉作用,有利于改善ＮＢＲ 和ＰＯＭ 之间相容性,因而可和ＰＯＭ 树脂形成良好的合金体系;当ＮＢＲ 含量达４０ｗｔ％ 时,ＰＯＭ／ＮＢＲ 体系出现脆 韧转变,从逾渗机制、剪切带机制、类互穿网络（ＩＰＮ） 作用机制等角度进行考察的结果证明,ＮＢＲ 对ＰＯＭ 树脂的增韧行为以及ＰＯＭ／ＮＢＲ 共混合金体系的脆 韧转变规律与ＰＯＭ／ＴＰＵ 体系相一致．     

High‐efficiency impact modifier prepared by coagulation emulsion polymerization through internal voiding toughening mechanism

This paper was an application of our previous study on particle coagulation mechanism (Colloid Polym Sci 291: 2385‐2398, 2013), and the effect of coagulation particle of acrylic impact modifiers (ACR) on polymer blend properties was investigated. The compatibility was relevant with the properties of shell phase rather than the structure of core phase. The rubber content was found to be the main influencing factor for toughening when rubber content less than 5%. However, when it reached to 7%, the dispersion of rubber became the primary parameter to dominate the toughness. The highest impact strength of poly(vinyl chloride) (PVC) toughened by coagulation particles was 1656 J/m, nearly 56 times than pure PVC, whereas only 45 times was reached when toughening by traditional ACR prepared by seeded emulsion polymerization; moreover, the brittle–ductile transition happened in advanced of 2 phr at ACR content. Scanning electron microscopy results showed that the shear yielding of the matrix and rubber cavitation were the major toughening mechanisms. Furthermore, the high performance of blend responsible for coagulation particles was discussed. Copyright © 2014 John Wiley & Sons, Ltd.     

Poly (vinyl chloride)/poly (α‐methylstyrene–acrylonitrile)/acrylic resin ternary blends with enhanced toughness and heat resistance

In this study, tough and high heat‐resistant poly (vinyl chloride) (PVC)/poly (α‐methylstyrene–acrylonitrile) (α‐MSAN) blends (70/30) containing acrylic resin (ACR) as a toughening modifier was prepared. With the addition of ACR, heat distortion temperature increased slightly, which corresponded with the increase in glass transition temperature measured by differential scanning calorimetry and dynamic mechanical thermal analysis. Thermogravimetric analysis showed that addition of ACR improved the thermal stability. With regard to mechanical properties, tough behavior was observed combined with the decrease in tensile strength and flexural strength. A brittle‐ductile transition (BDT) in impact strength was found when ACR content increased from 8 to 10 phr. The impact strength was increased by 34.8 times with the addition of 15 phr ACR. The morphology correlated well with BDT in impact strength. It was also suggested from the morphology that microvoids and shear yielding were the major toughening mechanisms for the ternary blends. Our present study offers insight on the modification of PVC, since combination of α‐MSAN and ACR improves the toughness and heat resistance of pure PVC simultaneously. Copyright © 2011 John Wiley & Sons, Ltd.     

Remarkably improved toughness and thermal stability of poly (vinyl chloride) (PVC)/poly (α-methylstyrene-acrylonitrile) (α-MSAN) blend with the assistance of two impact modifiers

The key drawback of impact modifier-toughened polymer is that the improved toughness is accompanied by loss in stiffness. Surprisingly, poly (vinyl chloride) (PVC)/poly (α-methylstyrene-acrylonitrile) (α-MSAN) blend was toughened without loss in stiffness by simply combining two impact modifiers-chlorinated polyethylene (CPE) and acrylic resin (ACR). The prepared blend's impact strength was 3.0 times higher than PVC/α-MSAN/CPE blend and 18.6 times higher than pure PVC/α-MSAN blend. An impressive thermal stabilizing effect was also achieved when CPE and ACR were combined. The improved toughness could be attributed to the overlap of the stress field between different impact modifiers, which help to form the continuum percolation of stress volume under impact loading.     

ACR-g-PVC复合粒子结构与对PVC的增韧效率

采用丙烯酸丁酯 (BA)和丙烯酸 2 乙基己酯 (EHA)交联共聚物为核 ,BA与EHA或甲基丙烯酸甲酯(MMA)与苯乙烯 (St)或MMA与丙烯酸乙酯 (EA)交联共聚物为壳 ,合成了 3种聚丙烯酸酯 (ACR) [P(BA EHA)、ACRⅠ、ACRⅡ ]胶乳 .以 3种ACR胶乳为种子 ,分别与氯乙烯 (VC)进行乳液接枝共聚 ,制备了相应 3种复合粒子 (ACR g PVC) .借助动态光散射法和透射电镜考察了ACR与复合乳胶粒的粒径与结构 ,表征了所研制材料的形态和冲击韧性 .研究结果表明 ,3种ACR g PVC材料的常温缺口冲击强度随ACR含量增加而显著提高 ,其突跃点的发生具有等橡胶量效应 ,其临界橡胶含量约为 4 % ,并采用脆 韧转变的临界粒子间距模型对其进行了解释 ;P(BA EHA)比核 壳ACRⅠ或ACRⅡ具有更高的增韧效率 ,依据复合粒子的两种理想结构模型对其增韧效率进行了分析 .     

纳米级SiO_2填充PVC/CPE复合材料研究

80年代以后发展起来的纳米材料被称为“2 1世纪最有前途的材料” ,已成为材料学中跨世纪的研究热点[1 ] 。纳米级无机粒子 /聚合物复合材料是纳米材料中的一种具有重要价值的新型材料 ,可广泛应用于橡胶、塑料、纤维三大合成材料之中[2 ] 。其中 ,纳米级ＳｉＯ2 是纳米材料中的重要一员 ,它被称作跨世纪的高科技材料[3] 。因此 ,本文就纳米级ＳｉＯ2 填充ＰＶＣ/ＣＰＥ复合材料进行探讨。1　实验部分自制 纳米级 (和普通超细 )ＳｉＯ2 ,平均粒径约为 5 0ｎｍ ,比表面积约为 30 0ｍ2 /ｇ ,经过特殊表面处理 ,再用偶联剂、分散剂处理 ,1 2 0…     

Synthesis and Structure Control of A New Kind of Inelastomer Impact Modifier with Core-shell Structure and Impact Modification to PVC/CPE

Introduction　　 As a structure material,a polymer has two important mechanical properties,i.e.,strength and toughing.Therefore,plastic toughening isalwaysa fundamental study on poly-mer materials.Traditionally,toughnessmodification isto make rubberasan elastomerimpactmodifier dispersed to plastic matrix which is hence toughened[1 ,2 ] .But as the toughness ofplastic is improved,the elastomerimpactmodifieralso reducesthe othermechanical propertiesof the material.Consequently,whether rigid par…     

插层型NBR/膨润土混杂材料及其对PVC增韧作用的研究

研究了胶乳插层法制备的丁腈橡胶 /有机改性膨润土 (NBR/OMB)混杂材料的力学性能和微观结构及其对聚氯乙烯 (PVC)的增韧作用。结果表明 :胶乳插层法制备的NBR/OMB混杂材料具有优异的力学性能 ;TEM和XRD结果表明 ,有部分NBR大分子嵌入到膨润土层间 ,形成较均匀、细致的分散。NBR/OMB混杂材料增韧PVC的效果明显优于NBR ,增韧后拉伸强度和弯曲强度的保持率明显提高     

PVC与核壳结构聚丙烯酸酯及环氧树脂的共混增韧

研究发现由分段乳液聚合丙烯酸丁酯、甲基丙烯酸甲酯、甲基丙烯酸缩水甘油酯制备的三层核壳结构共聚体和少量环氧树脂(含固化剂及促进剂)与PVC在适当配比下共混,可使改性PVC的抗冲击性能明显提高。考察了共混体系的组成与其冲击强度及断裂形态之间的关系。