MAS-NMR studies of lithium aluminum silicate (LAS) glasses and glass-ceramics having different Li2O/Al2O3 ratio

Emergence of phases in lithium aluminum silicate (LAS) glasses of composition (wt%) xLi₂O-71.7SiO₂-(17.7−x)Al₂O₃-4.9K₂O-3.2B₂O₃-2.5P₂O₅ (5.1≤x≤12.6) upon heat treatment were studied. ²⁹Si, ²⁷Al, ³¹P and ¹¹B MAS-NMR were employed for structural characterization of both LAS glasses and glass-ceramics. In glass samples, Al is found in tetrahedral coordination, while P exists mainly in the form of orthophosphate units. B exists as BO₃ and BO₄ units. ²⁷Al NMR spectra show no change with crystallization, ruling out the presence of any Al containing phase. Contrary to X-ray diffraction studies carried out, ¹¹B (high field 18.8 T) and ²⁹Si NMR spectra clearly indicate the unexpected crystallization of a borosilicate phase (Li,K)BSi₂O₆, whose structure is similar to the aluminosilicate virgilite. Also, lithium disilicate (Li₂Si₂O₅), lithium metasilicate (Li₂SiO₃) and quartz (SiO₂) were identified in the ²⁹Si NMR spectra of the glass-ceramics. ³¹P NMR spectra of the glass-ceramics revealed the presence of Li₃PO₄ and a mixed phase (Li,K)₃PO₄ at low alkali concentrations.     

Crystal-chemistry of mullite-type aluminoborates Al18B4O33 and Al5BO9: A stoichiometry puzzle

Orthorhombic Al₂O₃-rich aluminoborate is an important ceramic material for which two slightly different compositions have been assumed: Al₅BO₉ (5Al₂O₃:B₂O₃) and Al₁₈B₄O₃₃ (9Al₂O₃:2B₂O₃). The formula Al₁₈B₄O₃₃ (=Al_4.91B_1.09O₉) was derived from results of chemical analyses when crystal structure data were not yet available. Subsequent structural investigations indicated Al₅BO₉ composition. Nevertheless, Al₁₈B₄O₃₃ was still accepted as the correct stoichiometry assuming that additional B replaces 9% Al.Powder samples of both compositions and ones with excess boron were prepared by solid state reactions between α-Al₂O₃ and B₂O₃/H₃BO₃ at temperatures above 1100 °C and single-crystals were grown from flux at 1100 and 1550 °C. Products were investigated by single-crystal and powder XRD, ¹¹B and ²⁷Al solid-state MAS-NMR, Raman and FTIR spectroscopy as well as Laser-ablation ICP-MS. No indication of the predicted 9% B→Al substitution was found. LA ICP-MS indicated 12.36(27) wt% B₂O₃ corresponding to Al_4.97B_1.03O₉. Hence, the suggested Al₁₈B₄O₃₃ stoichiometry can be excluded for all synthesized samples. A very low amount of Al vacancies at a five-fold coordinated site are likely, charge balanced by an additional nearby three-fold coordinated B site. All evidences indicate that the title compound should be reported as Al_5−xB_1+xO₉ with x<0.038(6), which is close to Al₅BO₉.     

系列硅铝比纳米薄层ZSM-5分子筛的合成和表征

以自制不对称双子季铵盐表面活性剂为模板, 在水热合成体系中控制合成系列硅铝比纳米薄层ZSM-5分子筛.采用X射线衍射(XRD)、N₂吸附-脱附、X射线荧光光谱(XRF)、扫描电镜(SEM)和²⁷Al魔角旋转核磁共振(²⁷Al MAS-NMR)对合成的样品进行了表征. 详细研究了晶化温度、晶化时间、结构导向剂(SDA)用量、碱度等对合成的影响和纳米薄层ZSM-5分子筛的形成过程. 结果表明: 分子筛硅铝比越高, 结构导向剂用量越大, 所需的晶化时间越短; 晶化温度越高, 晶化时间越短; 且不同硅铝比纳米薄层ZSM-5分子筛的形貌规整度、比表面积和介孔/微孔孔容比例随着硅铝比而变化.     

Kinetic analysis of the thermal stability of lithium silicates (Li4SiO4 and Li2SiO3)

The kinetics describing the thermal decomposition of Li₄SiO₄ and Li₂SiO₃ have been analysed. While Li₄SiO₄ decomposed on Li₂SiO₃ by lithium sublimation, Li₂SiO₃ was highly stable at the temperatures studied. Li₄SiO₄ began to decompose between 900 and 1000 °C. However, at 1100 °C or higher temperatures, Li₄SiO₄ melted, and the kinetic data of its decomposition varied. The activation energy of both processes was estimated according to the Arrhenius kinetic theory. The energy values obtained were −408 and −250 kJ mol⁻¹ for the solid and liquid phases, respectively. At the same time, the Li₄SiO₄ decomposition process was described mathematically as a function of a diffusion-controlled reaction into a spherical system. The activation energy for this process was estimated to be −331 kJ mol⁻¹. On the other hand, Li₂SiO₃ was not decomposed at high temperatures, but it presented a very high preferential orientation after the heat treatments.     

MAS-NMR study of lithium zinc silicate glasses and glass-ceramics with various ZnO content

Lithium zinc silicate glasses of composition (mol%): 17.5Li₂O-(72−x)SiO₂-xZnO−5.1Na₂O−1.3P₂O₅−4.1B₂O₃, 5.5?x?17.7, were prepared by conventional melt-quenched technique and converted to glass-ceramic by controlled crystallization process. ²⁹Si and ³¹P MAS-NMR was used to characterize the structure of both glass and glass-ceramic samples. Despite the complex glass composition, Q², Q³ and Q⁴ sites are identified from ²⁹Si MAS-NMR, which relative intensities are found to vary with the ZnO content, indicating a network depolymerization by ZnO. Moreover, well separated Q³ and Q⁴ resonances for low ZnO content indicates the occurrence of phase separation. From ³¹P MAS-NMR, it is seen that phosphorus is mainly present in the form of ortho-(Q⁰) and pyro-phosphate (Q¹) structural units and variation of ZnO content did not have much effect on these resonances, which provides an additional evidence for phase separation in the glass. On conversion to glass-ceramics, lithium disilicate (Li₂Si₂O₅), lithium zinc ortho-silicate (Li₃Zn_0.5SiO₄), tridymite (SiO₂) and cristobalite (SiO₂) were identified as major silicate crystalline phases. Using ²⁹Si MAS-NMR, quantification of these silicate crystalline phases is carried out and correlated with the ZnO content in the glass-ceramics samples. In addition, ³¹P spectra unambiguously revealed the presence of crystalline Li₃PO₄ and (Na,Li)₃PO₄ in the glass-ceramics.     

Synthesis and nonlinear optical properties of BaTi(BO3)2 and Ba3Ti3O6(BO3)2 crystals in glasses with high TiO2 contents

The ternary BaO-TiO₂-B₂O₃ glasses containing a large amount of TiO₂ (20-40 mol%) are prepared, and their optical basicities (Λ), the formation, structural features and second-order optical nonlinearities of BaTi(BO₃)₂ and Ba₃Ti₃O₆(BO₃)₂ crystals are examined to develop new nonlinear optical materials. It is found that the glasses with high TiO₂ contents of 30-40 mol% show large optical basicities of Λ=0.81-0.87, suggesting the high polarizabity of TiO_n polyhedra (n=4-6) in the glasses. BaTi(BO₃)₂ and Ba₃Ti₃O₆(BO₃)₂ crystals are found to be formed as main crystalline phases in the glasses. It is found that BaTi(BO₃)₂ crystals tend to orient at the surface of crystallized glasses. The new XRD pattern for the Ba₃Ti₃O₆(BO₃)₂ phase is proposed through Rietvelt analysis. The second harmonic intensities of crystallized glasses were found to be 0.8 times as large as α-quartz powders, i.e., I^2ω(sample)/I^2ω(α-quartz)=0.8, for the sample with BaTi(BO₃)₂ crystals and to be I^2ω(sample)/I^2ω(α-quartz)=68 for the sample with Ba₃Ti₃O₆(BO₃)₂ crystals. The Raman scattering spectra for these two crystalline phases are measured for the first time and their structural features are discussed.     

Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

A neutron diffraction study of the d and d lithium garnets Li3Nd3W2O12 and Li5La3Sb2O12

The garnets Li₃Nd₃W₂O₁₂ and Li₅La₃Sb₂O₁₂ have been prepared by heating the component oxides and hydroxides in air at temperatures up to 950 °C. Neutron powder diffraction has been used to examine the lithium distribution in these phases. Both compounds crystallise in the space group with lattice parameters a=12.46869(9) Å (Li₃Nd₃W₂O₁₂) and a=12.8518(3) Å (Li₅La₃Sb₂O₁₂). Li₃Nd₃W₂O₁₂ contains lithium on a filled, tetrahedrally coordinated 24d site that is occupied in the conventional garnet structure. Li₅La₃Sb₂O₁₂ contains partial occupation of lithium over two crystallographic sites. The conventional tetrahedrally coordinated 24d site is 79.3(8)% occupied. The remaining lithium is found in oxide octahedra which are linked via a shared face to the tetrahedron. This lithium shows positional disorder and is split over two positions within the octahedron and occupies 43.6(4)% of the octahedra. Comparison of these compounds with related d⁰ and d¹⁰ phases shows that replacement of a d⁰ cation with d¹⁰ cation of the same charge leads to an increase in the lattice parameter due to polarisation effects.     

La7O6(BO3)(PO4)2:Eu3+/Tb3+荧光材料的制备及其光致发光性能

采用优化的高温固相方法制备了稀土离子Eu³⁺和Tb³⁺掺杂的La₇O₆（BO₃）（PO₄）₂系荧光材料,并对其物相行为、晶体结构、光致发光性能和热稳定性进行了详细研究。结果表明,La₇O₆（BO₃）（PO₄）₂：Eu³⁺材料在紫外光激发下能够发射出红光,发射光谱中最强发射峰位于616 nm处,为⁵D₀→⁷F₂特征能级跃迁,Eu³⁺的最优掺杂浓度为0.08,对应的CIE坐标为（0.610 2,0.382 3）;La₇O₆（BO₃）（PO₄）₂：Tb³⁺材料在紫外光激发下能够发射出绿光,发射光谱中最强发射峰位于544 nm处,对应Tb³⁺的⁵D₄→⁷F₅能级跃迁,Tb³⁺离子的最优掺杂浓度为0.15,对应的CIE坐标为（0.317 7,0.535 2）。此外,对2种材料的变温光谱分析发现Eu³⁺和Tb³⁺掺杂的La₇O₆（BO₃）（PO₄）₂荧光材料均具有良好的热稳定性。     

Effect of sintering on the ionic conductivity of garnet-related structure Li5La3Nb2O12 and In- and K-doped Li5La3Nb2O12

Garnet-structure related metal oxides with the nominal chemical composition of Li₅La₃Nb₂O₁₂, In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ and K-substituted Li_5.5La_2.75K_0.25Nb₂O₁₂ were prepared by solid-state reactions at 900, 950, and 1000 °C using appropriate amounts of corresponding metal oxides, nitrates and carbonates. The powder XRD data reveal that the In- and K-doped compounds are isostructural with the parent compound Li₅La₃Nb₂O₁₂. The variation in the cubic lattice parameter was found to change with the size of the dopant ions, for example, substitution of larger In³⁺(r_CN6: 0.79 Å) for smaller Nb⁵⁺ (r_CN6: 0.64 Å) shows an increase in the lattice parameter from 12.8005(9) to 12.826(1) Å at 1000 °C. Samples prepared at higher temperatures (950, 1000 °C) show mainly bulk lithium ion conductivity in contrast to those synthesized at lower temperatures (900 °C). The activation energies for the ionic conductivities are comparable for all samples. Partial substitution of K⁺ for La³⁺ and In³⁺ for Nb⁵⁺ in Li₅La₃Nb₂O₁₂ exhibits slightly higher ionic conductivity than that of the parent compound over the investigated temperature regime 25-300 °C. Among the compounds investigated, the In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ exhibits the highest bulk lithium ion conductivity of 1.8×10⁻⁴ S/cm at 50 °C with an activation energy of 0.51 eV. The diffusivity (“component diffusion coefficient”) obtained from the AC conductivity and powder XRD data falls in the range 10⁻¹⁰-10⁻⁷ cm²/s over the temperature regime 50-200 °C, which is extraordinarily high and comparable with liquids. Substitution of Al, Co, and Ni for Nb in Li₅La₃Nb₂O₁₂ was found to be unsuccessful under the investigated conditions.     

Structural studies in the BaO-B2O3-TiO2 system by XAS and B-NMR

The structure of barium-titanium-metaborate xBaO-xB₂O₃-yTiO₂ (y=0%, 4%, 8%, 16% and x=50-y/2) amorphous and crystallized powders, obtained using a polymeric precursor method, was investigated by Ti and B K-edge X-ray absorption spectroscopy (XAS) and ¹¹B-NMR high-resolution techniques. XANES study of amorphous samples shows that Ti⁴⁺ ions exist as ^[4]Ti species associated to ^[6]Ti and ^[5]Ti species in a practically equivalent amount. After crystallization, titanium environment is predominately composed by ^[6]Ti species. According to XANES results obtained at the B K-edge, the fraction of boron in tetrahedral sites (^[4]B) reduces as the amount of TiO₂ is increased from x=0% to 4%, with a consequent increase of boron in trigonal sites (^[3]B). By a combination of ¹¹B-NMR spin-echo and triple quantum magic angle spinning (3Q-MAS) techniques, the detailed borate speciation was determined as consisting in ^[4]B and two kind of trigonal sites, ^[3]B_A and ^[3]B_B, corresponding, respectively, to borates sharing three and two O atoms with other boron units. NMR results reveal not only the reduction in boron coordination also seen by XANES but also the simultaneous reduction in the condensation degree of trigonal units, when the Ti content is increased in the glass. In crystallized samples, β-BaB₂O₄ and BaTi(BO₃)₂ phases were identified and quantified by ¹¹B-NMR.     

ZrO4/SiO2-Al2O3催化肉桂醛MPV转移加氢性能

以九水合硝酸铝（Al（NO₃）₃·9H₂O）与正硅酸乙酯（TEOS）为前驱盐,采用溶胶-凝胶法制备一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,并通过浸渍硝酸氧锆引入ZrO₂,制备ZrO₂/SiO₂-Al₂O₃复合氧化物催化剂,考察催化剂在肉桂醛（CAL）MPV转移加氢中的催化性能,并结合N₂物理吸附、X射线粉末衍射（XRD）、傅里叶变换红外光谱（FTIR）、NH₃-程度升温脱附（NH₃-TPD）、Py-原位红外（Py-IR）等技术,研究催化剂结构、织构以及表面性质与其催化性能间的构效关系.研究表明,所制备的催化剂均以L酸为主,并含有少量B酸中心,这使得加氢产物以肉桂醇（COL）为主,并含有少量1-苯丙烯-2-丙基醚（CPE）.Al₂O₃含量不仅影响催化剂表面的酸中心数量,而且对催化剂的织构参数有较大影响.随Al₂O₃含量的增加,催化剂表面L酸与B酸中心均有所增加,而孔径则持续变小,这使得催化反应呈现CAL转化率先增加后减少、目标产物COL选择性先稍有减小后有所增加的趋势.在Si/Al比为2时,催化剂具有最优的催化性能,优化反应条件下,CAL转化率达96%,目标产物COL选择性达90%.     

Comparative computational investigation of N and F substituted polyoxoanionic compounds: The case of Li2FeSiO4 electrode material

First principles calculations are used to anticipate the electrochemistry of polyoxoanionic materials consisting of XO_{4 − y}A_y (A = F, N) groups. As an illustrative case, this work focuses on the effect of either N or F for O substitution upon the electrochemical properties of Li₂FeSiO₄. Within the Pmn2₁–Li₂FeSiO₄ structure, virtual models of Li₂Fe₂^2.5+SiO_3.5N_0.5 and Li_1.5Fe²⁺SiO_3.5F_0.5 have been analyzed. We predict that the lithium deinsertion voltage associated to the Fe^3+/Fe⁴⁺ redox couple is decreased by both substituents. The high theoretical specific capacity of Li₂FeSiO₄ (330 mAh/g) could be retained in N-substituted silicates thanks to the oxidation of N³⁻ anions, whilst Li_1.5Fe²⁺SiO_3.5F_0.5 has a lower specific capacity inherent to the F substitution. Substitution of N/F for O will respectively improve/worsen the electrode characteristics of Li₂FeSiO₄.     

La_7O_6(BO_3)(PO_4)_2∶Eu~(3+)/Tb~(3+)荧光材料的制备及其光致发光性能

采用优化的高温固相方法制备了稀土离子Eu~(3+)和Tb~(3+)掺杂的La_7O_6(BO_3)(PO_4)_2系荧光材料,并对其物相行为、晶体结构、光致发光性能和热稳定性进行了详细研究。结果表明,La_7O_6(BO_3)(PO_4)_2∶Eu~(3+)材料在紫外光激发下能够发射出红光,发射光谱中最强发射峰位于616 nm处,为5D0→7F2特征能级跃迁,Eu~(3+)的最优掺杂浓度为0.08,对应的CIE坐标为(0.610 2,0.382 3);La_7O_6(BO_3)(PO_4)_2∶Tb~(3+)材料在紫外光激发下能够发射出绿光,发射光谱中最强发射峰位于544 nm处,对应Tb~(3+)的5D4→7F5能级跃迁,Tb~(3+)离子的最优掺杂浓度为0.15,对应的CIE坐标为(0.317 7,0.535 2)。此外,对2种材料的变温光谱分析发现Eu~(3+)和Tb~(3+)掺杂的La_7O_6(BO_3)(PO_4)_2荧光材料均具有良好的热稳定性。     

Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al_2O_3-SiO_2系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho~(3+)/Yb~(3+)共掺以ZnAl_2O_4为主晶相的ZnO-Al_2O_3-GeO_2-SiO_2系玻璃陶瓷。因[GeO_4]四面体和[SiO_4]四面体都是玻璃网络形成体,讨论了GeO_2取代SiO_2对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO_2的取代量为10.55%(w/w)时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色(546 nm)和弱的红色(650 nm)上转换发光,并研究了不同Ho~(3+)/Yb~(3+)掺杂比对样品上转换发光的影响,最终结果表明当Ho~(3+)/Yb~(3+)掺杂比为1∶11(n/n)时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

共沉淀法和模板法制备均匀负载CeO2/ SiO2的研究

CeO2是三效催化剂(简称TWC)中被广泛应用的涂层材料[1],其优良的储放氧能力(OSC)可以扩大TWC的工作窗口,并可以在与γ-Al2O3的相互作用中提高Al2O3的高温稳定性[2]。在高温下,CeO2会因晶粒迅速长大而失去储放氧能力。为了提高CeO2的高温抗烧结能力,以及进一步提高其氧化还原能力,大部分研究者选择了在CeO2晶格中掺入其他离子的方法,如:Zr4 、Pr3 、La3 等[3￣5],这些离子在CeO2晶格中引入了晶格缺陷,不但稳定了结构,而且提高了氧传输能力。SiO2具有很高的化学稳定性、高比表面及高热稳定性,是载体的理想选择。研究表明,CeO2负载…     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

High-pressure transitions in MgAl2O4 and a new high-pressure phase of Mg2Al2O5

Phase transitions in MgAl₂O₄ were examined at 21-27 GPa and 1400-2500 °C using a multianvil apparatus. A mixture of MgO and Al₂O₃ corundum that are high-pressure dissociation products of MgAl₂O₄ spinel combines into calcium-ferrite type MgAl₂O₄ at 26-27 GPa and 1400-2000 °C. At temperature above 2000 °C at pressure below 25.5 GPa, a mixture of Al₂O₃ corundum and a new phase with Mg₂Al₂O₅ composition is stable. The transition boundary between the two fields has a strongly negative pressure-temperature slope. Structure analysis and Rietveld refinement on the basis of the powder X-ray diffraction profile of the Mg₂Al₂O₅ phase indicated that the phase represented a new structure type with orthorhombic symmetry (Pbam), and the lattice parameters were determined as a=9.3710(6) Å, b=12.1952(6) Å, c=2.7916(2) Å, V=319.03(3) Å³, Z=4. The structure consists of edge-sharing and corner-sharing (Mg, Al)O₆ octahedra, and contains chains of edge-sharing octahedra running along the c-axis. A part of Mg atoms are accommodated in six-coordinated trigonal prism sites in tunnels surrounded by the chains of edge-sharing (Mg, Al)O₆ octahedra. The structure is related with that of ludwigite (Mg, Fe²⁺)₂(Fe³⁺, Al)(BO₃)O₂. The molar volume of the Mg₂Al₂O₅ phase is smaller by 0.18% than sum of molar volumes of 2MgO and Al₂O₃ corundum. High-pressure dissociation to the mixture of corundum-type phase and the phase with ludwigite-related structure has been found only in MgAl₂O₄ among various A²⁺B³⁺₂O₄ compounds.     

Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al₂O₃-SiO₂系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho³⁺/Yb³⁺共掺以ZnAl₂O₄为主晶相的ZnO-Al₂O₃-GeO₂-SiO₂系玻璃陶瓷。因[GeO₄]四面体和[SiO₄]四面体都是玻璃网络形成体,讨论了GeO₂取代SiO₂对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO₂的取代量为10.55%（w/w）时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色（546 nm）和弱的红色（650 nm）上转换发光,并研究了不同Ho³⁺/Yb³⁺掺杂比对样品上转换发光的影响,最终结果表明当Ho³⁺/Yb³⁺掺杂比为1：11（n/n）时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

Electronic polarizability and crystallization of K2O-TiO2-GeO2 glasses with high TiO2 contents

Some K₂O-TiO₂-GeO₂ glasses with a large amount of TiO₂ contents (15-25 mol%) such as 25K₂O-25TiO₂-50GeO₂ have been prepared, and their electronic polarizability, Raman scattering spectra, and crystallization behavior are examined to clarify thermal properties and structure of the glasses and to develop new nonlinear optical crystallized glasses. It is proposed that the glasses consist of the network of TiO₆ and GeO₄ polyhedra. The glasses show large optical basicities of Λ=0.88-0.92, indicating the high polarizabity of TiO_n (n=4-6) polyhedra in the glasses. K₂TiGe₃O₉ crystals are formed through crystallization in all glasses prepared in the present study. In particular, 20K₂O-20TiO₂-60GeO₂ glass shows bulk crystallization and 18K₂O-18TiO₂-64GeO₂ glass exhibits surface crystallization giving the c-axis orientation. The crystallized glasses show second harmonic generations (SHGs), and it is suggested that the distortion of TiO₆ octahedra in K₂TiGe₃O₉ crystals induces SHGs.