Melting behavior of ethylene oxide–propylene oxide (sym-PEP) block copolymers

Melting points and lamellar thicknesses have been measured for ethylene oxide–propylene oxide block copolymers (sym-PEP) with central poly(ethylene oxide) block lengths of 70–100 chain units and end poly(propylene oxide) block lengths of 0–30 chain units. Melting points of the block copolymers are lower than those of the corresponding poly(ethylene oxide) homopolymer by an amount (up to 15°C) which increases as the poly(propylene oxide) block length increases. Most samples have more than one melting transition, which can be assigned to variously folded chain crystals. End interfacial free energies σ_e for the various crystals have been estimated by use of Flory's theory of melting of block copolymers. For a given crystal type (e.g., once-folded-chain) σ_e is higher the longer the chain length of the end poly(propylene oxide) blocks. For a given copolymer σ_e is lower, the more highly folded the poly(ethylene oxide) chain.     

Copolymerization of Carbonyl Sulfide and Propylene Oxide via a Heterogeneous Prussian Blue Analogue Catalyst with High Productivity and Selectivity

This study demonstrates the superiority of a stable and well-defined heterogeneous cobalt hexacyanocobaltate (Co₃[Co(CN)₆]₂), a typical cobalt Prussian Blue Analogue (CoCo-PBA) that catalyzes the copolymerization of carbonyl sulfide (COS) and propylene oxide (PO) to produce poly(propylene monothiocarbonate)s (PPMTC). The number-average molecular weights of the PPMTC were 66.4 to 139.4 kg/mol, with a polydispersity of 2.0–3.9. The catalyst productivity reached 1040 g polymer/g catalyst (12.0 h). The oxygen-sulfur exchange reaction (O/S ER), which would generate random thiocarbonate and carbonate units, was effectively suppressed, and thus the selectivity of the monothiocarbonate over carbonate linkages was up to >99%. It was shown that no cyclic thiocarbonate byproduct was produced during the heterogeneous catalysis of COS/PO copolymerization using CoCo-PBA as the catalyst. The content of monothiocarbonate and ether units in the copolymer chain could be regulated by tuning the feeding amount of COS.     

A new thioether functionalized organic-inorganic mesoporous composite as a highly selective and capacious Hg2+ adsorbent

A new thioether functionalized organic-inorganic ordered mesoporous composite as a highly selective and capacious Hg2+ adsorbent was synthesized by one-step co-condensation of (1,4)-bis(triethoxysilyl)propane tetrasufide (BTESPTS, (CH3CH2O)3Si(CH2)3S-S-S-S(CH2)3Si(OCH2CH3)3) and tetraethoxysilane (TEOS), with tri-block copolymer poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) EO20PO70EO20 as template.     

Isotactic sequence lengths by ozonation of poly(propylene oxide)

Ozonation followed by lithium aluminum hydride reduction cleaved high molecular weight isotactic poly(propylene oxide) to crystalline polyglycols. From the melting point and molecular weight of the latter, the molar freezing point depression produced by end groups is found to be ca. 18°C./mole, as compared to that estimated for poly(ethylene glycols), K_f = 12°C./mole, from earlier data. By assuming syndiotactic placements (or other irregularities) would produce the same molar depression, the melting point of isotactic poly(propylene oxides) produced by various catalysts has been used to estimate the isotactic sequence lengths.     

Interaction between zero-charged catanionic vesicles and PEO–PPO–PEO triblock copolymers

We investigate the interaction between zero-charged catanionic vesicles and PEO–PPO–PEO (poly(ethylene oxide–poly(propylene oxide)–poly(ethylene oxide)) triblock copolymers. The 25-mg mL^?1 aqueous solution of tetradecyltrimethylammonium laurate (TTAL) contains closely packed uni- and multi-lamellar vesicles and shows viscoelastic properties with a dominant elastic modulus (G′) over a viscous modulus (G″). When a small amount of F127 ((EO)₉₇(PO)₆₉(EO)₉₇) or F68 ((EO)₇₆(PO)₂₉(EO)₇₆) was added, an improvement of the viscoelasticity was observed at suitable polymer concentrations. Freeze–fracture transmission electron microscopy (FF-TEM) observations on an F68-containing system revealed interesting aggregate transition from vesicles to flexible tubules and back to vesicles. The improvement of the viscoelasticity of the vesicular solution containing F68 or F127 can be explained by the formation of tubule and polymer–vesicle associates, while no such phenomenon was noticed for P123 ((EO)₁₉(PO)₆₉(EO)₁₉) which has the highest propylene oxide (PO) content and the strongest ability to self-associate in aqueous solution. In all the cases, vesicles will be destroyed and phase separation can be observed at high polymer contents (>5-mg mL^?1).     

Conductivity–modulus–Tg relationships in solvent-free,single lithium ion conducting network electrolytes

A model system of single-ion conducting network electrolytes with acrylic backbone, ethylene oxide (EO) side chains, tethered fluorinated anions, and mobile Li cations was designed and synthesized to investigate structure–property relationships. By systematically tuning four molecular variables, one at a time, we investigated how crosslinker length, mol% of crosslinker added, Li:EO ratio and side-chain length affect conductivity, T_g, and modulus. Ionic conductivity at 90 °C varied by two orders of magnitude (and by three orders of magnitude at room temperature) depending on the molecular details, while a 70 °C span in glass transition temperature (T_g) was observed. The range of crosslinking, which can be achieved without impacting conductivity was also elucidated, and the modulus of the electrolyte can be increased by a factor of 8, up to 2.4 MPa, without impacting ion transport. Changes in conductivity due to crosslink density and crosslinker length are fully explained in terms of T_g shifts, while comonomer length cannot be accounted for by such a shift. The best performing network exhibited 10⁻⁵ S/cm at high temperature, which is comparable to other single-ion conductors reported in the literature, while the modulus is higher due to crosslinking. Adding 10 wt% propylene carbonate further increased this value to 10⁻⁴ S/cm. This work provides insights into the structure–property relationships of solid-state polymer electrolytes, which retain conductivity but can potentially help suppress dendrites.     

Thermodynamic Behavior of Non-Ionic Tri-block Copolymers in Water at Three Temperatures

Apparent molar volumes (V _Φ) of aqueous solutions of some copolymers, based on ethylene oxide (EO) and propylene oxide (PO) units, were determined as functions of concentration at three temperatures. Viscosity measurements were also carried out on some of these systems. The effects studied include how the molecular architecture and the molecular weight affect the aggregation of the copolymer, keeping constant the EO/PO ratio. Modeling of the volumetric data yielded the partial molar volume of the copolymer in the standard (V°) and the aggregated (V _M) states, as well as the equilibrium constant for micellization and the aggregation number. Analysis of the viscosity data supported the insights obtained by modeling of the volumetric data. At a given temperature, both V° and V _M, normalized for the number of the EO and the PO units, are linearly related to the fraction of the EO in the copolymer, regardless of the copolymer nature. These correlations are powerful tools for predicting values of both V° and V _M for copolymers not yet investigated. For macromolecules having the same molecular architecture, the standard Gibbs free energies of micellization () are slightly negative within the errors of their determination, and are hardly affected by temperature changes. Also, their aggregation numbers are small. From the quantitative analysis of the viscosity data, insights were obtained that corroborated the thermodynamic findings. Finally, values of , normalized for the EO and the PO units, show that the same driving forces control the self-assembling processes for copolymers having different molecular weight but the same EO/PO ratio.     

Synthesis of bromine-functionalized polyolefins by scandium-catalyzed copolymerization of 10-bromo-1-decene with ethylene,propylene, and dienes

By use of a THF-containing trimethylsilylmethyl scandium catalyst system (C₅Me₄SiMe₃)Sc(CH₂SiMe₃)₂(THF)/[Ph₃C][B(C₆F₅)₄], the multi-component copolymerization of 10-bromo-1-decene (BrDC) with ethylene, propylene, and dienes has been achieved to afford a new family of bromine-functionalized polyolefins with controllable composition and high molecular weight. The copolymerization of BrDC with ethylene afforded the well-defined BrDC–ethylene copolymers with high BrDC incorporation (up to 12 mol%) and high molecular weight (M_w > 100 kg mol⁻¹). The terpolymerization of propylene, ethylene with BrDC afforded random ethylene–propylene–BrDC terpolymers with controllable bromine content (2 ~ 11 mol%), high molecular weight (M_w > 100 kg mol⁻¹) and low glass transition temperature (T_g = −51 °C ~ −67 °C). Moreover, the tetrapolymerization of ethylene, propylene, BrDC, and ethylidene norbornene or conjugated dienes such as isoprene and myrcene has been achieved for the first time to afford selectively the bromine-functionalized ethylene–propylene–diene rubbers containing various types of double bonds.     

Double metal cyanide catalyst prepared using H3Co(CN)6 for high carbonate fraction and molecular weight control in carbon dioxide/propylene oxide copolymerization

Simple mixing of H₃Co(CN)₆ and ZnCl₂ in methanol resulted in precipitates of [ZnCl]⁺₂[HCo(CN)₆]^2?, constituting a new type of double metal cyanide (DMC) catalyst exhibiting a high performance in carbon dioxide (CO₂)/propylene oxide (PO) copolymerization. High‐molecular‐weight poly(propylene carbonate‐co‐propylene oxide)s [poly(PC‐co‐PO)s] (M_n～40,000) were consistently obtained with high carbonate fractions (～60 mol %) and a high selectivity (>95%) with the new type of DMC catalyst. Conventional preparation of the DMC catalyst using K₃Co(CN)₆ and ZnCl₂ required removing KCl through thorough washing and resulted in lower carbonate fractions (10–40 mol %), which depended on the washing conditions. Feeding hydrophobic diols such as 1,10‐decanediol as chain transfer agent preserved the high carbonate fraction (～60%) and enabled precise control of the molecular weight, including preparation of a low‐molecular‐weight poly(PC‐co‐PO)‐diol (M_n ～2000), which was a flowing viscous liquid with a low T_g (?30 °C) suitable for polyurethane applications. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4811–4818     

Regio‐regular structure high molecular weight poly(propylene carbonate) by rare earth ternary catalyst and Lewis base cocatalyst

Lewis base modification strategy on rare earth ternary catalyst was disclosed to enhance nucleophilic ability of active center during copolymerization of carbon dioxide and propylene oxide (PO), poly(propylene carbonate) (PPC) with H‐T linkages over 83%, and number–average molecular weight (M_n) up to 100 kg/mol was synthesized at room temperature using Y(CCl₃OO)₃‐ZnEt₂‐glycerine catalyst and 1,10‐phenanthroline (PHEN) cocatalyst. Coordination of PHEN with active Zinc center enhanced the nucleophilic ability of the metal carbonate, which became more regio‐specific in attacking carbon in PO, leading to PPC with improved H‐T linkages. Moreover, the binding of PHEN to active Zinc center also raised the carbonate content of PPC to over 99%, whereas the PPC from common rare earth ternary catalyst was about 96%. Unlike the highly regio‐regular structure PPC but with relatively low molecular weight recently reported in the literature, our high molecular weight regio‐regular PPC did show significant improvement in thermal and mechanical performances. PPC with H‐T linkages up to 83.2% showed glass transition temperature (T_g) of 43.3 °C, while T_g of PPC with H‐T linkages of 69.7% was only 36.1 °C. When H‐T connectivity was raised from 69.7 to 83.2%, the modulus of PPC showed a 78% increase. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4451–4458, 2008     

Full separation of oligomers in block copolymers of ethylene oxide and propylene oxide

In this study di‐ and triblock copolymers of ethylene oxide (EO) and propylene oxide (PO) are analyzed by using CAP for one block and adsorption for the other block. This gives a complete picture of EO‐ and PO‐based block copolymer with respect to the oligomers of both blocks. A full resolution of the individual oligomers can be achieved for both blocks up to an average molecular weight of 1000–1500 of each block.     

Preparation,characterization, and thermal properties of alt‐copoly[1,9‐decaphenylpentasiloxanylene/1,3‐bis(ethylene)permethyloligosiloxanylene]s

alt‐Copoly[1,9‐decaphenylpentasiloxanylene/1,3‐bis(ethylene)tetramethyldisiloxanylene], alt‐copoly[1,9‐decaphenylpentasiloxanylene/1,5‐bis(ethylene)hexamethyltrisiloxanylene], alt‐copoly[1,9‐decaphenylpentasiloxanylene/1,7‐bis(ethylene)octamethyltetrasiloxanylene], and alt‐copoly[1,9‐decaphenylpentasiloxanylene/1,9‐bis(ethylene)decamethylpentasiloxanylene] were synthesized by Pt‐catalyzed hydrosilylation reactions of 1,9 divinyldecaphenylpentasiloxanes with a series of oligodimethylsiloxanes. The molecular weights of these copolymers were determined by gel permeation chromatography. Their glass‐transition temperatures (T_g's) were obtained by differential scanning calorimetry. The thermal stabilities of the copolymers were measured by thermogravimetric analysis. The structures of the copolymers were verified by ¹H, ¹³C, and ²⁹Si NMR as well as IR and UV spectroscopy. The copolymers displayed high thermal stabilities and a single T_g, indicating that phase separation between the two short blocks did not occur. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6146–6152, 2005     

Preparation,characterization, and properties of poly(thioether ether imide)s from isomeric bis(chlorophthalimide)s and 4,4′‐thiobisbenzenethiol

A series of isomeric poly(thioether ether imide)s (PTEIs) containing both thioether and ether linkages were prepared by nucleophilic substitution reaction of isomeric bis(chlorophthalimide)s with 4,4′‐thiobisbenzenethiol. The inherent viscosities of these polymers were in the range of 0.40–0.56 dL/g in m‐cresol at 30°C. The T_g values of PTEIs were 196–236°C; T_5% values reached up to 509–529°C in nitrogen and 508–534°C in air, which indicated this kind of polyimide possessed excellent thermal stability. The hydrolytic stability was arranged in the order: a > b > c > d > e, and improved with increasing the content of 3‐substituted phthalimide unit in the polymer backbone. Flexible films could be cast from the polymer solution with a solid content of 10%. The PTEI films exhibited good mechanical properties with tensile strengths of 90–104 MPa, elongations at break of 6.6–7.9%, and tensile moduli of 2.3–2.6 GPa. The minimum complex viscosity of PTEIs c was about 100 Pa·s at 310°C and the minimum melt viscosity of PTEIs (a–e) decreased with increasing the content of unsymmetrical 3,4′‐substituted phthalimide units. Copyright © 2014 John Wiley & Sons, Ltd.     

Copolymerization of 2‐isothiocyanatoethyl methacrylate and 2‐hydroxyethyl methacrylate or methacrylic acid based on a nucleophile‐tolerant property of the isothiocyanato group

Radical copolymerizations of 2‐isothiocyanatoethyl methacrylate (ITEMA) and 2‐hydroxyethyl methacrylate (HEMA) or methacrylic acid (MAA) were examined, and fundamental properties of the obtained copolymers were investigated. The copolymerizations of various ITEMA/HEMA or ITEMA/MAA compositions proceeded effectively in THF or DMF by using 2,2′‐azobisbutyronitrile (AIBN) as an initiator, keeping the isothiocyanato groups and hydroxyl or carboxyl groups unchanged. Glass transition temperatures (T_g)s of poly(ITEMA‐co‐HEMA)s ranged from 68 to 100 °C, and they were thermally stable up to 200 °C. Meanwhile, T_gs of poly(ITEMA‐co‐MAA)s (ITEMA/MAA = 91/9, 76/24) were determined to be 91 and 109 °C, respectively. However, poly(ITEMA‐co‐MAA)s were thermally unstable, and significant weight loss was observed around 180 °C, which may be due to an addition of carboxyl groups to isothiocyanato groups followed by an elimination of COS to form amide structure in the copolymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5221–5229     

Heptane-soluble homogeneous zirconocene catalyst: Synthesis of a single diastereomer,polymerization catalysis,and effect of silica supports

Bis(1-indenyl)-di[1′S, 2′R, 5′S)-methoxy]silane ( 1 ) was converted into a mixture of corresponding ansa-diastereomeric zirconocenes. Further purification afforded a single dia-stereomer, di[(1′S, 2′R, 5′S)-methoxy] silylene-bis[η⁵-1(R, R)-(+)-indenyl] dichlorozirconium ( 2 ), which is optically active and hydrocarbon soluble. Extremely rapid ethylene, propylene, and ethylene-hexene polymerizations were observed both in toluene and n-heptane solutions; for instance, at 50°C, activity for ethylene polymerization reaches ～ 1.5×10¹⁰ (g of PE/((mol of Zr) · [C₂H₄] · h). The “bare” zirconocenium ion generated from 2/TIBA/Ph₃CB(C₆F₅)₄ exhibits unusual polymerization behaviors; the polymerization activity increases monotonically with temperature of polymerization (T_p) up to a conventional polymerization condition (50–70°C), and the ¹³C NMR study shows that the isotactic poly-propylene obtained has fairly high [mmmm] methyl pentad distributions at high T_p (?25°C with [mmmm] ～ 0.93–0.75) and a perfect stereoregularity at low T_p (?0°C with [mmmm] > 0.99). The catalyst precursors 2 and Et(Ind)₂ZrCl₂ ( 3 ) supported on silica by different approaches produced poly(olefins) of different molecular weights and stereoregularities, and a methylaluminokane and Ph₃CB(C₆F₅)₄ free silica-supported zirconocene system was found to be activated by triisobutylaluminum. © 1995 John Wiley & Sons, Inc.     

Silolene-Bridged zirconocenium polymerization catalysts

A new silolene-bridged compound, racemic (1,4-butanediyl) silylene-bis (1-η⁵-in-denyl) dichlorozirconium ( 1 ) was synthesized by reacting ZrCl₄ with C₄H₈Si (IndLi)₂ in THF. 1 was reacted with trialkylaluminum and then with triphenylcarbenium tetrakis (penta-fluorophenyl) borate ( 2 ) to produce in situ the zirconocenium ion ( 1 ⁺). This “constraint geometry” catalyst is exceedingly stereoselective for propylene polymerization at low temperature (T_p = ?55°C), producing refluxing n-heptane insoluble isotactic poly(propylene) (i-PP) with a yield of 99.4%, T_m = 164.3°C, δH_f = 20.22 cal/g and M?_w = 350 000. It has catalytic activities of 10⁷?10⁸ g PP/(mol Zr · [C₃H₆] · h) in propylene polymerization at the T_p ranging from ?55°C to 70°C, and 10⁸ polymer/(mol Zr · [monomer] · h) in ethylene polymerization. The stereospecificity of 1 ⁺ decreases gradually as T_p approaches 20°C. At higher temperatures the catalytic species rapidly loses stereochemical control. Under all experimental conditions 1 ⁺ is more stereospecific than the analogous cation derived from rac-dimethylsilylenebis (1-η⁵-indenyl)dichlorozirconium ( 4 ). The variations of polymerization activities in ethylene and in propylene for T_p from ?55°C to +70°C indicates a Michaelis Mention kinetics. The zirconocenium-propylene π-complex has a larger insertion rate constant but lower thermal stability than the corresponding ethylene π-complex. This catalyst copolymerizes ethylene and propylene with reactivity ratios of comparable magnitude r_E ? 4r_p. Furthermore, r_E.r_p ? 0.5 indicating random copolymer formation. Both 1 and 4 activated with methylaluminoxane (MAO) exhibit much slower polymerization rates, and, under certain conditions, a lower stereo-selectivity than the corresponding 1 ⁺ or 4 ⁺ system. © 1994 John Wiley & Sons, Inc.     

Coatings with thermally switchable surface energy produced from poly(ethylene oxide)-poly(dimethylsiloxane) block copolymer films

This work explores coatings with thermally switchable wetting behavior, based on block copolymers that possess both hydrophilic and hydrophobic segments. The amphiphilic block copolymers were synthesized by coupling allyl-ended poly(ethylene oxide) (PEO) and hydride-ended poly(dimethylsiloxane) (PDMS) oligomers via a Pt catalyst. One near-symmetric diblock possessed an order-disorder transition temperature (T_ODT) of 64 °C. When cooled through T_ODT in ambient air, the PDMS domains wet the film's surface, producing a hydrophobic coating with a water contact angle (CA) = 90°. However, when cooled in humidified air, hydrophilic PEO domains form at the surface, yielding CA = 30–40°. The coatings can be reversibly switched between the two states by reheating above T_ODT, in the appropriate environment, and then cooling, rapidly generating the desired room-temperature surface wettability. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 135–140     

Random thermotropic elastomers. I. Effects of substitution and hard/soft segment lengths on properties

Syntheses of segmented copoly(ether-ester)s with (oxy-2-methyl-1,4-phenyleneoxycarbonyl-1,4-phenylene carbonyl)/(oxy-2-chloro-1,4-phenyleneoxycarbonyl-1,4-phenylene carbonyl) (methyl-/chloro-substituted) hard segments and poly(oxytetramethylene) soft segments, are reported. The methodology consisted of staged addition melt condensation of terephthaloyl chloride, poly(oxytetramethylene)glycol (POTMG; \[ \bar M_n \] = 250, 650, 1000, 2000) and methyl-/chloro-hydroquinone. Lengths of hard and soft segments were varied while the weight ratio of hard to soft segment was maintained constant. Copolymers were characterised for solubility behavior, and by infrared spectroscopy, x-ray diffraction, DSC, and polarizing microscopy. Thermal properties were found to be dependent on length of soft segment as well as on the type of substituent in the mesogenic core. In both methyl- as well as chloro-substituted copoly(ether-ester)s soft segment glass transition temperature (T_gs) was obtained between ?40 and ?50°C. All copoly(ether-ester)s are elastomeric at room temperature (25°C). These polymers exhibit thermotropic liquid crystalline behavior and were easily sheared and aligned in liquid crystalline state. © 1994 John Wiley & Sons, Inc.     

Multistimuli responsive grafted poly(ether tert‐amine) (gPEA): Synthesis,characterization and controlled morphology in aqueous solution

Multistimuli responsive grafted poly(ether tert‐amine) (gPEAs), which were comprised of poly(propylene oxide) (PPO) in backbone and poly(ethylene oxide) (PEO) as grafted chain, were successfully synthesized through nucleophilic addition/ring‐opening reaction of commercial poly(propylene glycol) diglycidyl ether and Jeffamine L100. These gPEAs exhibit very sharp response to temperature, pH and ionic strength with tunable cloud point (CP). The CP of gPEA aqueous solution increases with increasing the PEO content or decreasing pH value, varying from 27 to 77 °C. Compared with linear PEA101, gPEA110 of completely grafted structure in aqueous solution exhibits sharper response to temperature with ΔT around 1 °C. The results obtained from TEM and dynamic light scattering reveal that gPEAs are dispersed as uniform sized nano‐micelles in aqueous at room temperature, which can further aggregate into mesoglobules of complex structure at high temperature (>CP). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6353–6361, 2009