分子模拟研究气体在室温离子液体中的溶解度

在作者先前建立的分子力场基础上, 采用Widom粒子插入法预测了CO₂、N₂、O₂、Ar及CH₄等5种气体在多种咪唑类离子液体中的溶解度, 包括2种侧链长度的阳离子和3种阴离子. 首先考察了256个离子对组成的体系中溶质分子插入次数对计算结果的影响, 在此基础上计算了不同温度下气体在1-丁基-3-甲基咪唑的四氟化硼盐([bmim][BF₄])和六氟化磷盐([bmim][PF₆])中的溶解度. 计算结果正确反映了CO₂气体溶解度的变化趋势, 在[bmim][BF₄]中溶解度的模拟结果与实验值符合很好, 且明显优于Pádua等的模拟结果；在[bmim][PF₆]中的溶解度较实验值偏高, 精度与文献模拟结果相当；并预测了较高温度下CO₂气体在[bmim][BF₄]和[bmim][PF₆]中的溶解度. 计算结果也正确地反映了5种气体在[bmim][PF₆]中溶解度实验值的相对大小. 另外考察了常温下几种气体在不同室温离子液体中的溶解度, 模拟结果表明气体在含有较长碳链和双-三氟甲基磺酰胺阴离子(Tf₂N^－)的离子液体中溶解度较大.     

室温离子液体[bmim][BF4]和水混合物的计算机模拟研究

针对室温离子液体[bmim][BF₄]和水的混合物, 用分子动力学模拟研究了溶液的微观组成与浓度的关系. 模拟结果表明：该混合物中各组分间的径向分布函数随[bmim][BF₄]摩尔分数的增加呈有规律的变化；在此基础上计算了溶液的局部组成以及组分间的缔合因子, 进一步考察了各组分间的相互作用情况；另外基于Kirkwood-Buff理论估算了混合物的偏摩尔体积、等温压缩因子以及活度系数对浓度的偏导数, 对于理解离子液体与水之间的交互作用具有一定的参考意义.     

烷基咪唑离子液体对脂肪酶催化酯水解反应活性的影响

考察了1-烷基-3-甲基咪唑类离子液体对柱状假丝酵母脂肪酶(CRL)催化橄榄油水解反应活性的影响,利用电导法确定了磷酸盐缓冲液中Br^-,Cl^-,[BF₄]^-系列咪唑离子液体的临界胶束浓度(CMC)和[PF₆]^-系列咪唑离子液体的溶解度.结果显示,离子液体的阴、阳离子对酶活性的影响规律与离子液体的Kosmotropicity性质无明显关联,但与离子液体在体系中的含量密切相关,在最适离子液体含量时,酶活性达到最高;阳离子[C_nMIM]⁺中的n越大,可促进酶活性的离子液体适宜含量越低;Br^-,[BF₄]^-系列离子液体的浓度超过CMC时则抑制酶活;阴离子对酶活性的最大促进作用顺序为Br^->Cl^->[BF₄]^->[PF₆]^-.离子液体对酶活性的影响随体系pH和温度的不同而改变,在最适离子液体浓度时的最适pH均为7.000.在pH 7.000,30 ^oC以及[C₈MIM]Br离子液体浓度为47.6 mmol/L的最佳条件下,最高相对酶活力和比活力分别达到1734%和54.4 U/mg protein.     

离子液体1-烷基-3-甲基咪唑四氟硼酸盐在水溶液中的聚集行为

采用等温滴定量热法、静态荧光猝灭法和电导法系统研究了典型离子液体1-烷基-3-甲基咪唑四氟硼酸盐([Cnmim][BF₄])在水溶液中的聚集行为, 获得了胶束形成的临界胶束浓度(cmc), 摩尔焓变(ΔH_mic), 摩尔吉布斯自由能变(ΔG_mic), 摩尔熵变(ΔS_mic)以及不同浓度时[Cnmim][BF₄]胶束的平均聚集数等基本参数. 发现这类离子液体的聚集为熵驱动, 阳离子的烷基链越长, ΔG_mic越负, 聚集更容易发生. 此外, 结合[C_nmim]X (X=Cl^-, Br^-)的相关研究发现, 阳离子相同时, 体积越大和疏水性越强的阴离子与头基的结合能力越强, 能有效地降低头基之间的静电排斥, 降低cmc, 利于胶束的形成. 对于[C₁₂mim][BF₄], 添加剂β-环糊精(β-CD)的加入可使cmc增大, ΔH_mic和ΔS_mic减小, 而KBF₄则可使cmc和ΔH_mic减小, ΔS_mic增大.     

在离子液体中一步法合成吡唑[5,4-b]-γ-吡喃衍生物

芳醛、丙二腈与4,5-二氢-3-甲基-5-氧代-1-苯基吡唑在离子液体[bmim][BF₄]中反应, 合成了2-氨基-4-芳基-3-氰基-5-甲基-7-苯基吡唑[5,4-b]-γ-吡喃衍生物, 该法快速、高效, 是一种洁净的合成方法. 产物的结构通过红外光谱、核磁共振氢谱和元素分析进行表征.     

离子液体/水混合溶剂促进芳醛与罗丹宁的缩合反应

在室温条件下, 离子液体1-正丁基-3-甲基咪唑四氟硼酸盐([bmim]BF₄)与水组成的混合溶剂能有效催化一系列芳醛与罗丹宁反应, 以80%～93%的产率生成相应的5-芳亚甲基-2,4-噻唑二酮. 离子液体[bmim]BF₄催化活性高, 反应在10～120 min内完成. 实验结果表明该法反应条件温和、产率高、反应时间短、后处理简单、离子液体可重复使用.     

在ITO导电衬底上室温电沉积高取向的CuBr薄膜

室温下,通过简单的电沉积过程还原CuBr₂水溶液可在ITO导电衬底上生长出高取向的CuBr晶体。用X-射线衍射仪(XRD)、扫描电镜(SEM)对样品进行了表征。结果表明：CuBr晶体生长沿着<111>晶轴方向具有优先取向。通过烷基咪唑四氟硼酸盐[Bmim][BF₄]离子液体来调控电沉积CuBr的晶体形貌,添加[Bmim][BF₄]后,CuBr晶体生长 (111)面优先取向大大削弱。对离子液体调控CuBr晶体形貌的机理进行了初步探讨。     

离子液体[BMIM]Br与[BMIM][BF4]配比浓度对Br-离子电荷转移的调节

利用X射线吸收精细结构光谱(XAFS)及紫外吸收光谱两种方法, 分析了离子液体1-丁基-3-甲基咪唑溴盐([BMIM]Br)中逐渐掺入1-丁基-3-甲基咪唑四氟硼酸盐([BMIM][BF₄])时, Br^-阴离子与咪唑阳离子之间氢键作用及电荷偏移量的改变. 随着[BMIM][BF₄]加入量增多, Br 元素XAFS近边(XANES)显示吸收峰降低, 吸收边位置向低能端位移0.9 eV; 扩展边(EXAFS)算出径向结构显示Br 与近邻原子间平均配位数降低、平均键长增长; 紫外光谱也有明显蓝移减色效应. 这些结果都表明Br₄^-的掺入改变了Br^-与阳离子间的电荷偏移量, 负电荷更多地转移到Br^-上, 量化计算的数据同样支持该结论.     

在离子液体[BMIm][BF4]中电沉积光亮金镀层

在离子液体1-丁基-3-甲基咪唑四氟硼酸盐（[BMIm][BF₄]）中以HAuCl₄·3H₂O为主盐、通过添加5,5-二甲基乙内酰脲（DMH）和胞嘧啶可得到色泽光亮、厚度达1.5 μm的金镀层,沉积过程中阴极电流效率可达到100%。SEM和XRD测试结果表明,DMH和胞嘧啶具有细化晶粒、平整镀层的作用。电化学测试结果表明,DMH可分别与Au³⁺、Au⁺形成配合物Au（DMH）₄^-、Au（DMH）₂^-,抑制了还原过程的表面转化步骤,从而增加了阴极极化,起到光亮镀层、细化晶粒的作用;胞嘧啶可在金核表面吸附,从而可以进一步光亮镀层、细化晶粒,与DMH有协同作用。循环伏安测试研究了镀液的电化学行为,研究表明在此体系中Au³⁺的还原为两步还原过程,分别为Au³⁺→ Au⁺和Au⁺→ Au。此外DMH和胞嘧啶的添加不会带来副反应。     

在离子液体[BMIm][BF4]中电沉积光亮金镀层

在离子液体1-丁基-3-甲基咪唑四氟硼酸盐（[BMIm][BF₄]）中以HAuCl₄·3H₂O为主盐、通过添加5,5-二甲基乙内酰脲（DMH）和胞嘧啶可得到色泽光亮、厚度达1.5 μm的金镀层,沉积过程中阴极电流效率可达到100%。SEM和XRD测试结果表明,DMH和胞嘧啶具有细化晶粒、平整镀层的作用。电化学测试结果表明,DMH可分别与Au³⁺、Au⁺形成配合物[Au（DMH）₄]^-、[Au（DMH）₂]^-,抑制了还原过程的表面转化步骤,从而增加了阴极极化,起到光亮镀层、细化晶粒的作用;胞嘧啶可在金核表面吸附,从而可以进一步光亮镀层、细化晶粒,与DMH有协同作用。循环伏安测试研究了镀液的电化学行为,研究表明在此体系中Au³⁺的还原为两步还原过程,分别为Au³⁺→ Au⁺和Au⁺→ Au。此外DMH和胞嘧啶的添加不会带来副反应。     

Ionic liquid induced changes in the properties of aqueous zwitterionic surfactant solution

Modifying properties of aqueous surfactant solutions by addition of external additives is an important area of research. Unusual properties of ionic liquids (ILs) make them ideal candidates for this purpose. Changes in important physicochemical properties of aqueous zwitterionic N-dodecyl- N, N-dimethyl-3-ammonio-1-propanesulfonate (SB-12) surfactant solution upon addition of hydrophilic IL 1-butyl-3-methylimidazolium tetrafluoroborate, [bmim][BF 4], are reported. Dynamic light scattering results indicate a dramatic reduction in the average micellar size in the presence of [bmim][BF 4]; micellar (or micelle-like) aggregation in the presence of as high as 30 wt % [bmim][BF 4] is confirmed. Responses from fluorescence probes are used to obtain critical micelle concentration (cmc), aggregation number ( N agg), and dipolarity and microfluidity of the micellar pseudophase of aqueous SB-12 in the presence of [bmim][BF 4]. In general, increasing the amount of [bmim][BF 4] to 30 wt % results in decrease in N agg and increase in cmc. Increase in the dipolarity and the microfluidity of the probe cybotactic region within the micellar pseudophase is observed on increasing [bmim][BF 4] concentration in the solution. It is attributed to increased water penetration into the micellar pseudophase as [bmim][BF 4] is added to aqueous SB-12. It is proposed that IL [bmim][BF 4] behaves similar to an electrolyte and/or a cosurfactant when present at low concentrations and as a polar cosolvent when present at high concentrations. Electrostatic attraction between cation of IL and anion of zwitterion, and anion of IL and cation of zwitterion at low concentrations of [bmim][BF 4] is evoked to explain the observed changes. Presence of IL as cosolvent appears to reduce the efficiency of micellization process by reducing the hydrophobic effect.     

Concentration-dependent dual behavior of hydrophilic ionic liquid in changing properties of aqueous sodium dodecyl sulfate

Modifying physicochemical properties of aqueous surfactant solutions in favorable fashion by addition of environmentally benign room-temperature ionic liquids (ILs) has enormous future potential. Due to its unusual properties, an IL may demonstrate a unique role in altering the properties of aqueous surfactant solutions. Changes in the properties of aqueous sodium dodecyl sulfate (SDS), an anionic surfactant, upon addition of a common and popular "hydrophilic" ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate [bmim][BF4] are presented. Addition of low concentrations of [bmim][BF4] (i.e., 相似文献   

Unique role of hydrophilic ionic liquid in modifying properties of aqueous Triton X-100

Modification of important physicochemical properties of aqueous surfactant solutions can be achieved by addition of environmentally benign room temperature ionic liquids (ILs). While low aqueous solubility of "hydrophobic" ILs limits the amount of IL that may be added to achieve desired changes in the physicochemical properties, hydrophilic ILs do not have such restrictions associated to them. Alterations in the key physicochemical properties of aqueous solutions of a common nonionic surfactant Triton X-100 (TX100) on addition of up to 30 wt % hydrophilic IL 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4]) are reported. The presence of micellar aggregates in as high as 30 wt % [bmim][BF4]-added aqueous TX100 solutions is established by dynamic light scattering and fluorescence probe behavior. Increasing the concentration of [bmim][BF4] results in decrease in average micellar size and aggregation number and increase in critical micelle concentration, indicating an overall unfavorable aggregation process. Increase in the dipolarity and the microfluidity of the probe cybotactic region within the palisade layer of the micellar phase upon [bmim][BF4] addition implies increased water penetration and the possibility of TX100-[bmim][BF4] interactions. While the changes in some of the physicochemical properties indicate the role of [bmim][BF4] to be similar to a cosurfactant, the IL acts like a cosolvent as far as changes in other properties are concerned. Effectiveness of IL [bmim][BF4] in modifying physicochemical properties of aqueous TX100 is demonstrated.     

添加中低浓度离子液体[bmim][BF4]对吐温-20临界胶束浓度和胶束结构的影响

添加离子液体会对表面活性剂在水溶液中的聚集行为产生重要影响。本文研究了吐温-20在中低浓度离子液体四氟硼酸1-丁基-3-甲基咪唑鎓([bmim][BF_4])中的胶束化行为。随着[bmim][BF_4]浓度(cIL)从0增加到0.2mol·L~(-1),吐温-20的临界胶束浓度逐渐增大。相比cIL0.05mol·L~(-1),在cIL0.05mol·L~(-1)时加入[bmim][BF_4]使吐温-20临界胶束浓度增大得更加显著。吐温-20胶束聚集数随着离子液体浓度的增加而逐渐减小,这一结果也说明加入离子液体会对吐温-20胶束的生成有抑制作用。吐温-20胶束化热力学研究表明,吐温-20在不同浓度离子液体中的胶束化是熵、焓共同驱动,并具有熵-焓补偿性。随着离子液体浓度的增加,吐温-20胶束平均粒径和胶束微粘性均表现出先增大后减小的变化,在cIL=0.05mol·L~(-1)时达到最大值。     

1-丁基-3-甲基咪唑四氟硼酸盐的热稳定性、平衡蒸汽压和标准蒸发焓

利用非等温、等温热重分析(TG)法,研究了高纯氮气气氛下1-丁基-3-甲基咪唑四氟硼酸盐([bmim][BF4])离子液体的热稳定性、平衡蒸汽压和标准蒸发焓.非等温热重(TG)曲线表明[bmim][BF4]的初始分解温度(Tonset)和最大分解速率对应的温度(Tm)分别为697和734K.然而长期等温TGA研究表明,[bmim][BF4]的最高可使用温度约为513K.另外,利用基于TG的蒸发技术研究了[bmim][BF4]的平衡蒸汽压(pe)与温度的关系并计算了标准蒸发焓.在503-543K温度范围内,离子液体[bmim][BF4]的pe和温度的关系是:lgpe=(16±1)+(-6.85±0.25)×103/T.[bmim][BF4]的标准蒸发焓为(131±5)kJ·mol-1.     

Nucleophilicity in ionic liquids. 3. Anion effects on halide nucleophilicity in a series of 1-butyl-3-methylimidazolium ionic liquids

We have continued the study of halide nucleophilicity in ionic liquids, concentrating on the effect of changing the anion ([BF(4)](-), [PF(6)](-), [SbF(6)](-), [OTf](-), and [N(Tf)(2)](-)) when the cation is [bmim](+) (where bmim = 1-butyl-3-methylimidazolium). It was found that the nucleophilicities of all the halides were lower in all of the ionic liquids than in dichloromethane. Changing the anion affected the order of halide nucleophilicity, e.g., in [bmim][BF(4)] the order of nucleophilicity was Cl(-)>Br(-)>I(-) while in [bmim][N(Tf)(2)] the order was Cl(-)相似文献   

Dynamics of solvent and rotational relaxation of coumarin-153 in room-temperature ionic liquid 1-butyl-3-methyl imidazolium tetrafluoroborate confined in poly(oxyethylene glycol) ethers containing micelles

We have investigated solvent and rotational relaxation of coumarin 153 (C-153) in room-temperature ionic liquid (RTILs) 1-butyl-3-methyl-imidazolium tetrafluoroborate ([bmim][BF(4)]) and the ionic liquid confined in alkyl poly(oxyethylene glycol) ethers containing micelles. We have used octaethylene glycol monotetradecyl ether (C(14)E(8)) and octaethylene glycol monododecyl ether (C(12)E(8)) as surfactants. In the [bmim][BF(4)]-C(14)E(8) micelle, we have observed only a 22% increase in solvation time compared to neat [bmim][BF(4)], whereas in the [bmim][BF(4)]-C(12)E(8) system, we have observed approximately 57% increase in average solvation time due to micelle formation. However, the slowing down in solvation time on going from neat RTIL to RTIL-confined micelles is much smaller compared to that on going from water to water confined micellar aggregates. The 22-57% increase in solvation time is attributed to the slowing down of collective motions of cations and anions in micelles. The rotational relaxation times become faster in both the micelles compare to neat [bmim][BF(4)].     

Thermodynamic modeling of the phase behavior of binary systems of ionic liquids and carbon dioxide with the group contribution equation of state

The group contribution equation of state (GC-EOS) was applied to predict the phase behavior of binary systems of ionic liquids of the homologous families 1-alkyl-3-methylimidazolium hexafluorophosphate and tetrafluoroborate with CO2. Pure group parameters for the new ionic liquid functional groups [-mim][PF6] and [-mim][BF4] and interaction parameters between these groups and the paraffin (CH3, CH2) and CO2 groups were estimated. The GC-EOS extended with the new parameters was applied to predict high-pressure phase equilibria in binary mixtures of the ionic liquids [emim][PF6], [bmim][PF6], [hmim][PF6], [bmim][BF4], [hmim][BF4], and [omim][BF4] with CO2. The agreement between experimental and predicted bubble point data for the ionic liquids was excellent for pressures up to 20 MPa, and even for pressures up to about 100 MPa, the agreement was good. The results show the capability of the GC-EOS to describe phase equilibria of systems consisting of ionic liquids.     

Cu(I)(bpp)]BF4: the first extended coordination network prepared solvothermally in an ionic liquid solvent

Use of an ionic liquid [bmim][BF4] (bmim = 1-butyl-3-methylimidazolium) as solvent has resulted in the first extended coordination structure, the two-dimensional network [Cu(bpp)]BF4 [bpp = 1,3-bis(4-pyridyl)propane], produced via a solvothermal route.     

Molecular dynamics simulation of room-temperature ionic liquid mixture of [bmim][BF4] and acetonitrile by a refined force field

1-Butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF4]) is one of the promising room-temperature ionic liquids. To test the refined force field for [bmim][BF4] proposed in our previously work (J. Phys. Chem. B, 2004, 108, 12978-12989), thermodynamic properties of mixtures of [bmim][BF4](1)+ acetonitrile (2) are presented by using molecular dynamics over the whole concentration range. The calculated densities are in good agreement with the experimental data with deviations less than 2%, indicating the force field is applicable to the mixtures. In addition, the diffusion constants, viscosities, heats of vaporization, cohesive energy densities and excess properties of the mixtures are reported. The microscopic structures are discussed in detail, corresponding to the thermodynamic properties.