P(MMA-M12-BPMA)乳液的合成及紫外吸收性能

以甲基丙烯酸甲酯(MMA)、可聚合乳化剂马来酸酐衍生物磺酸钠(M12)和可聚合紫外线吸收剂2-羟基-4-(3-甲基丙烯酰氧基-2-羟基丙氧基)苯甲酮(BPMA)为原料,采用乳液聚合方法制备了P(MMA-M12-BP-MA)共聚物乳液。通过转化率、红外光谱、以及紫外吸收光谱测定,分别研究了M12含量对聚合反应速率的影响、所得共聚产物的结构、以及共聚物乳液和共聚物紫外吸收特性。结果表明,随M12含量增大,聚合反应速率增加;BPMA含量增大有利于提高共聚物乳液和共聚物紫外吸收性能。     

PDA/PVDF紫外线屏蔽复合膜的制备及性能表征

利用多巴胺在溶液中自聚得到聚多巴胺(PDA)颗粒, 然后将其作为填料加入聚偏氟乙烯(PVDF)中, 采用溶液成膜法制备具有紫外线屏蔽功能的PDA/PVDF复合膜. 通过傅里叶变换红外光谱(FTIR)、 扫描电子显微镜(SEM)和紫外可见分光光度计(UV-Vis)对制备的PDA颗粒的结构、 形貌以及吸光度进行表征, 并且进一步利用X 射线衍射仪(XRD)、 差示扫描量热仪(DSC)、 热失重分析仪(TGA)、 接触角测量仪(CA)以及紫外老化箱等对PDA/PVDF复合膜的结构、 热性能、 润湿性能与紫外线屏蔽性能进行测试. 结果表明, 制备的PDA颗粒的粒径约为160 nm; 掺杂PDA之后的PVDF膜的结晶度以及接触角均减小; 并且PDA质量分数为5%时得到的PDA/PVDF复合膜在200400 nm范围内的透过率均低于1%, 能够吸收所有的紫外线, 表现出优异的紫外线屏蔽功能.     

1,2-环氧丙醚基芳香酮紫外线吸收剂的微波合成和表征

以2,4-二羟基二苯甲酮、4-羟基苯乙酮(HAP)为原料分别和环氧氯丙烷反应,经微波辐照合成了两种反应性紫外线吸收剂2-羟基-4-缩水甘油醚基二苯甲酮(HEPBP)和4-缩水甘油醚基苯乙酮(EPAP)。结构采用红外光谱、核磁和质谱表征。最佳合成条件为:n(羟基芳香酮)∶n(环氧氯丙烷)=1∶3,微波功率400W,于90℃反应15min,收率分别是52.6%和58.3%。与常规合成方法比较,微波合成法能降低反应温度、大大地缩短反应时间。产物中环氧丙烷基团的引入能明显改善芳香酮类紫外线吸收剂的紫外吸收性能。     

5-苯甲酰基-2,4-二羟基苯甲醛的合成、晶体结构及紫外吸收性能研究

以2,4-二羟基二苯甲酮为原料,经过醚化、Vilsmeier-Haack反应和脱甲基化三步反应制备5-苯甲酰基-2,4-二羟基苯甲醛,反应总收率达到74.1%。通过~1H NMR、~(13)C NMR、IR、MS和X-ray单晶衍射对目标产物进行结构表征,晶体结构显示两个苯环并不共平面,分子内和分子间的氢键连接分子形成三维网状结构。考查该化合物的紫外吸收性能,在293 nm和324 nm有很好的紫外吸收,兼具长波紫外线UVA和中波紫外线UVB的吸收性能。     

新型有机/无机复合紫外吸收剂的制备及其在PVC中的应用

将全波段紫外吸收剂聚苯并咪唑(PBI)与纳米SiO_2复配制备了有机/无机复合紫外吸收剂,用于改善聚氯乙烯(PVC)的紫外老化性能。为了增强纳米SiO_2与PBI之间的相互作用,先用硅烷偶联剂γ-氨丙基三乙氧基硅烷对纳米SiO_2改性,产物命名为MSiO_2,然后将PBI涂覆到MSiO_2表面得到复合填料PBI@MSiO_2,最后将填料与PVC通过溶体共混制备复合材料。使用紫外-可见分光光度计和万能拉伸试验机等对复合材料的紫外吸收性能和力学性能等进行了表征和对比分析。结果表明,PBI@MSiO_2粒子显著改善了复合材料的紫外吸收性能,375nm处的紫外吸收率可达99%;并改善了复合材料的力学性能和屈服强度,当PBI@MSiO_2质量分数为6%时,复合材料屈服强度可达63.3MPa。     

静电纺聚偏氟乙烯@硅藻土锂离子电池隔膜的制备及性能

以聚偏氟乙烯(PVDF)和硅藻土为原料,通过静电纺丝法制备PVDF@硅藻土复合纤维膜,用于锂离子电池隔膜。 研究了隔膜的吸液率、热稳定性和电化学性能等。 添加硅藻土可有效提高复合膜的电解液吸收率和电化学性能,其中吸液率可达623.6%,相比于PVDF膜和聚丙烯(PP)膜具有优异的循环性能和倍率性能。     

Dawson磷钼钒酸的合成、脱硫与微波辅助空气再生

采用乙醚萃取法制备了Dawson结构磷钼钒酸H6+n[P2Mo18-nVnO62](n=1～4),考察了不同钒原子取代数目、吸收温度、H2S气体浓度、杂多酸吸收剂浓度等条件下,4种杂多酸水溶液对H2S的吸收效率,发现其中H7[P2Mo17VO62]吸收剂具有最佳脱硫性能。采用微波辅助空气再生的方法对脱硫后的H7[P2Mo17VO62]吸收剂强化再生,通过红外、X射线能谱着重对吸收前、微波再生前后的H7[P2Mo17VO62]吸收剂进行了表征,并通过测定氧化还原电位、化学需氧量(COD)分析了再生前后吸收剂的氧化还原情况,结果表明,H2S还原V(Ⅴ)之后又进一步还原了Mo(Ⅵ),微波能够活化氧气从而促进脱硫后吸收剂的再生,是优于单纯空气再生的一种新的再生方法。     

自组装金纳米粒子涂层对环境水样中紫外线吸收剂的固相微萃取

以刻蚀不锈钢丝为基体,采用化学沉积法在表面沉积金纳米粒子(AuNPs),修饰一层1,8-辛二硫醇分子后,再自组装一层AuNPs,制备了高强度AuNPs涂层固相微萃取(SPME)纤维,并与HPLC联用,以常用紫外线吸收剂为例,评价了AuNPs-SPME纤维的萃取分离性能。当萃取时间为30 min、温度为55℃、搅拌速率为800 r/min,pH=7时,萃取效果最好。在优化的萃取条件下,所建立的Au NPs-SPME-HPLC法测定4种紫外吸收剂(2-羟基-4-甲氧基二苯甲酮、2-乙基己基-4-(N,N-二甲氨基)苯甲酸酯、2-乙基己基-4-甲氧基肉桂酸酯和2-乙基己基水杨酸)的线性范围为0.004~200μg/L,检出限为0.43~570 ng/L(S/N=3),相对标准偏差(RSD)在1.9%~4.2%(n=5)之间。河水、废水处理厂的废水以及雨水样品中紫外线吸收剂的加标回收率在77.9%~108%之间,RSD为3.1%~8.0%(n=5)。     

TiO_2/PVDF复合中空纤维膜的制备和表征

采用相转化法制备了二氧化钛 (TiO2 ) 聚偏氟乙烯 (PVDF)复合中空纤维膜 .应用牛血清白蛋白截留实验、扫描电子显微镜、热重分析、X射线衍射分别对复合膜的分离性能、微观结构、热稳定性和晶相组成进行了分析 .结果表明复合膜的性能与纯PVDF膜的相比有显著的改善 ,其中对牛血清白蛋白的截留率从 3 2 7%提高到 86 6 7% ,单根纤维的断裂应力从 3 35MPa提高到 4 70MPa ,提高了 4 0 3% .氮气吸附实验测定的孔径分布进一步表明复合膜的孔径分布变窄 ,孔径变小 .     

热处理工艺对静电纺丝制备PVDF/PMMA复合膜的力学性能的影响

利用热处理工艺对静电纺丝制备复合膜聚偏氟乙烯/聚甲基丙烯酸甲酯(PVDF/PMMA)进行改性,研究不同温度与不同压力对复合膜力学性能的影响,并与商用膜Celgard 2400在力学性能、离子电导率、循环性能方面进行对比。结果表明:在温度145℃,压强0.05 MPa时,PVDF/PMMA复合膜的拉伸强度为19.0 MPa,是未加压处理时其拉伸强度的10倍;PVDF/PMMA复合膜室温下的离子电导率为1.180mS/cm,比商用膜室温下的离子电导率高出187%;由PVDF/PMMA复合膜组装的纽扣电池在0.2C倍率下的放电比容量为140 (mA·h)/g,在1C倍率下的放电比容量为130(mA·h)/g,与商用膜同倍率下的放电比容量相同;在5C倍率下PVDF/PMMA复合膜的循环性能更优。     

Synthesis and characterization of a polymerizable benzophenone derivative and its application in styrenic polymers as UV-stabilizer

In this paper, a polymerizable UV-stabilizer 2-hydroxy-4-(3-methacryloxy-2-hydroxylpropoxy) benzophenone (BPMA) was synthesized by the reaction of 2,4-dihydroxybenzophenone (UV-0) and glycidyl methacrylate (GMA), and characterized by ultraviolet-visible absorption spectroscopy (UV-Vis), Fourier transform infrared spectroscopy (FTIR) and proton nuclear magnetic resonance (¹H NMR). The results show that BPMA, with high UV-absorbing performance, has been synthesized successfully. Poly(St-co-BPMA) was prepared by emulsion copolymerization of styrene (St) and BPMA, and tested by ¹H NMR, UV-Vis, gel permeation chromatography (GPC) and differential scanning calorimeter (DSC). The results reveal that BPMA had been added to the polymer chain as copolymer and the UV-resistant performance of poly(St-co-BPMA) was enhanced significantly by the incorporation of BPMA onto the polymer chains. Poly(St-co-BPMA) was irradiated under UV light and insoluble substance, reduced viscosity, weight loss and UV-Vis absorption spectra were used to determine the degradation of poly(St-co-BPMA). The results show that BPMA is an effective UV-stabilizer in protecting poly(St-co-BPMA) from UV destroys. We also take water extraction test on poly(St-co-BPMA), PSt/UV-0 blends, and the results show that migration problem can be resolved by anchoring the UV-stabilizer onto the polymer chain.     

Preparation and characterization of poly(MMA-M12-BPMA)/TiO2 composite particles

In this paper, poly(MMA-M12-BPMA)/TiO₂ composite particles were prepared by the copolymerization of a reactive surfactant sodium sulfopropyl-laurylmaleate (M12) and a reactive UV-stabilizer 2-hydroxy-4-(3-methacryloxy-2-hydroxylpropoxy) benzophenone (BPMA) with methyl methacrylate (MMA) in the presence of TiO₂. The structure and performance of composite particles were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy, gel permeation chromatography, ultraviolet–visible absorption spectroscopy, differential scanning calorimeter, and scanning electron microscope.The measurement results indicate that the percentage of grafting and the grafting efficiency can reach 336.87% and 36.38%, respectively, and the glass transition temperature of poly(MMA-M12-BPMA)/TiO₂ composite particles is higher than that of poly(MMA-M12-BPMA); the size of the composite particles is about 130–200 nm. The poly(MMA-M12-BPMA) grafted from the surface of TiO₂ keeps the excellent characteristic of BPMA that possesses high absorbance of ultraviolet light, which is very important for improving UV-resistant performance of the polymethyl methacrylate. These research results are very useful for preparing polymethyl methacrylate with resistance to UV light.     

Studies on UV‐stability of poly(MMA‐co‐M12‐co‐BPMA)/TiO2composite particles prepared by ultrasonically initiated emulsion polymerization

In this paper, poly(methyl methacrylate‐co‐sodium sulfopropyl lauryl maleate‐co‐2‐hydroxy‐4‐(3‐methacryloxy‐2‐hydroxylpropoxy) benzophenone)/TiO₂ (i.e., poly(MMA‐co‐M12‐co‐BPMA)/TiO₂) composite particles were prepared by ultrasonically initiated emulsion polymerization. To study the dispersion and UV‐stability of the composite particles, laser diffraction particle size analyzer (LDPSA), ultraviolet‐visible absorption spectroscopy (UV‐vis), UV‐vis diffuse reflectance spectroscopy (DRS), differential scanning calorimeter (DSC), and the weight loss measurement were used. The results indicate that the dispersion of the poly(MMA‐co‐M12‐co‐BPMA)/TiO₂ composite particles prepared by ultrasonically initiated emulsion polymerization is good. And the composite particles can absorb UV light; the ultraviolet absorption strength of poly(MMA‐co‐M12‐co‐BPMA) grafted onto the surface of TiO₂ has not changed after UV irradiation while that of PMMA changed significantly. The UV absorption strength, weight loss, and Tg changes are in the order PMMA> poly(MMA‐co‐M12‐co‐BPMA) >PMMA grafted onto TiO₂> poly(MMA‐co‐M12‐co‐BPMA) grafted onto TiO₂. These results show that the ultrasonically initiated emulsion polymerization will enhance the UV stability of composite particles, and the UV‐stability of PMMA can be enhanced by the introduction of the organic UV‐stabilizer BPMA and the inorganic UV‐stabilizer titanium dioxide into the PMMA chains by covalent bond, and the effect of the BPMA and the TiO₂ used together is better than that used, respectively. Copyright © 2009 John Wiley & Sons, Ltd.     

Improvement in the blood compatibility of polyvinylidene fluoride membranes via in situ cross‐linking polymerization

In this study, we have provided a highly efficient, convenient, and universal protocol for preparing polyvinylidene fluoride (PVDF) membranes with low blood contact activation via in situ cross‐linking copolymerization of 2‐hydroxyethl methacrylate (HEMA) and acrylic acid (AA) in a solution of PVDF. The modified membranes were prepared from PVDF solution by phase inversion technology. The composition and morphology of the modified membranes were confirmed by attenuated total reflectance‐Fourier transform infrared (ATR‐FTIR) spectroscopy, thermogravimetric (TG) analysis, and scanning electron microscopy (SEM). Protein adsorption, clotting time, and contact activation on the modified PVDF membranes were systematically studied, the results indicating that after the incorporation of AA and HEMA, the modified PVDF membranes possessed anticoagulant properties in addition to low contact activation of blood components when in contact with blood. Therefore, fluorinated PVDF membranes with surfaces enriched with carboxyl and hydroxyl groups possessed the potential for use in long‐term blood‐contacting devices.     

Functional and surface-active membranes from poly(vinylidene fluoride)-graft-poly(acrylic acid) prepared via RAFT-mediated graft copolymerization

Poly (vinylidene fluoride) (PVDF) with "living" poly (acrylic acid) (PAAc) side chains (PVDF-g-PAAc) was prepared by reversible addition-fragmentation chain transfer (RAFT)-mediated graft copolymerization of acrylic acid (AAc) with the ozone-pretreated PVDF. The chemical composition and structure of the copolymers were characterized by elemental analysis, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The copolymer could be readily cast into pH-sensitive microfiltration (MF) membranes with enriched living PAAc graft chains on the surface (including the pore surfaces) by phase inversion in an aqueous medium. The surface composition of the membranes was determined by X-ray photoelectron spectroscopy. The morphology of the membranes was characterized by scanning electron microscopy. The pore size distribution of the membranes was found to be much more uniform than that of the corresponding membranes cast from PVDF-g-PAAc prepared by the "conventional" free-radical graft copolymerization process. Most important of all, the MF membranes with surface-tethered PAAc macro chain transfer agents, or the living membrane surfaces, could be further functionalized via surface-initiated block copolymerization with N-isopropylacrylamide (NIPAAM) to obtain the PVDF-g-PAAc-b-PNIPAAM MF membranes, which exhibited both pH- and temperature-dependent permeability to aqueous media.     

Synthesis of a novel water-soluble polymeric UV-absorber for cotton

A water-soluble polymeric UV-absorber with polyvinylamine as backbone and benzotriazole type UV absorber as anti-UV functional group was synthesized by grafting brominated(2’-acetoxy-5’-methylphenyl)-2H-benzotriazole onto polyvinylamine. The intermediates and synthesized polymeric UV absorber were characterized by ~1H NMR,MS,IR and UV spectroscopy.The finishing properties of the polymeric UV absorber on cotton were investigated to show good UV protection property and wash fastness.     

改性聚偏氟乙烯接枝共混聚苯乙烯磺酸膜的制备与性能

将苯乙烯添加到溶有原硅酸钠改性的聚偏氟乙烯(PVDF)N-甲基吡咯烷酮溶液中, 以过氧化苯甲酰(BPO)作引发剂, 苯乙烯直接接枝到原硅酸钠改性的PVDF链上, 成膜后磺化制备了聚偏氟乙烯接枝苯乙烯(PVDF-g-PSSA)膜. 采用傅立叶变换红外光谱(FT-IR)、扫描电镜(SEM)、能量扩散X射线(EDX)和多功能材料实验机表征了膜的结构、形貌及硫和硅的分布、机械强度、溶胀度, 使用阻抗分析和气相色谱仪研究了苯乙烯含量(w)对PVDF-g-PSSA膜的质子导电性能和阻醇性能的影响. 结果表明, 苯乙烯加入后, 原硅酸钠改性的PVDF与苯乙烯进行接枝共聚反应, 苯乙烯磺化反应不只是在膜表面进行, 同时渗入到膜中进行, 机械性能得到了改善. 质子电导率(σ)随苯乙烯质量分数的提高而升高. Na4SiO4为8%和苯乙烯为20%的PVDF-g-PSSA膜, 在25 ℃时溶胀度仅为20.4%, 甲醇透过系数在10-7 cm2·s-1数量级上, 比Nafion115膜的低一个数量级. 该膜具有较高的选择性, 在直接甲醇燃料电池中具有良好的应用前景.