L-半胱氨酸/漆酶修饰的纳米金阴极对氧还原的电催化

以四氯金酸和L-半胱氨酸为原料,合成了L-半胱氨酸功能化纳米金粒子,将此纳米粒子修饰在金盘电极表面并共价偶联漆酶分子。 以循环伏安法研究了此固定漆酶电极在无氧磷酸盐缓冲液中电化学行为和催化氧还原能力,并进一步评估了其作为氧传感器使用的性能：以计时电流法测定其对氧气的检测限,与氧气的亲和力（以米氏常数表征）,研究了传感器的长期使用性、热稳定性和pH-催化电流关系。 结果表明,此固定漆酶电极可以实现漆酶活性中心T2与导电纳米粒子间的直接电子迁移而无需任何外加电子中介体（氧化还原峰的式电位为192.5 mV vs AgCl/Ag）,并在接近漆酶活性中心T3氧化还原式电位（780 mV vs NHE）附近发生氧还原;测得的固酶电极与氧气的亲和力较高（米氏常数为216.4 μmol/L）且检测限低达0.22 μmol/L,在4 ℃下保存60 d后活力仍然保持初始活力的大约78%。 但这种电极的热稳定性较差,受pH值影响较明显,在pH值近于生理条件时几乎完全丧失活力。     

聚芳酰胺-多壁碳纳米管混合物固定漆酶电极的电化学行为

以聚芳酰胺-多壁碳纳米管混合物为载体,利用漆酶表面氨基与聚芳酰胺主链端羧基的共价偶联以及碳纳米管与漆酶间的疏水作用,构筑了具有较高稳定性和电催化活性的漆酶修饰电极.并对该固酶修饰电极的固酶量、酶活力、电化学行为及其电催化氧还原的性能进行了表征.对漆酶分子具有亲和力的聚芳酰胺芳环结构及聚芳酰胺端羧基与漆酶表面氨基的共价偶联避免了漆酶的脱落和变性.而碳纳米管与聚芳酰胺的混合使得该三维修饰电极具有良好的电子导电性,并成功地实现了漆酶的氧化还原活性位与电极之间的直接电荷转移,这一点可由在0.73和0.38V附近观察到漆酶的T1和T2(漆酶的T1,T2铜活性位的形式电位分别为0.78和0.39V(vsNHE))铜活性位的两对氧化还原峰确认.漆酶的担载量为56.0mg·g-1,具有电化学活性的漆酶占总担载漆酶量的68%.在pH=4.4磷酸盐缓冲溶液中,该修饰电极上氧气还原的起始电位为0.55V,其对氧气的米氏常数KM为55.8μmo·lL-1,对氧气的检测限为0.57μmo·lL-1.在4℃下保存两个月后能实现直接电荷转移的漆酶量仅下降了14%左右而氧还原超电势提高了约50mV.结果表明该修饰电极有望用作酶基生物燃料电池的阴极和电流型氧气传感器.     

高分子聚合物-多壁碳纳米管复合物固定漆酶及其在玻碳电极上的直接电子迁移

采用不同结构的高分子聚合物与纯化的多壁碳纳米管(MWCNTs)共混的方法,制备得到聚合物非共价功能化多壁碳管复合物,测定了这些载体对漆酶(lac)的担载量、固定漆酶的比活力及稳定性.以固定漆酶的复合物修饰玻碳(GC)电极后,采用循环伏安法研究这些电极在无氧磷酸盐缓冲液(PBS)中的直接电化学行为及催化氧还原活力,粗略地测定了固定漆酶与电极间电子转移的速率常数.实验结果表明,当聚合物中含亲漆酶基团或能与漆酶活性中心发生相互作用的官能团时利于直接电子转移,而且复合物固定漆酶保持了游离漆酶的天然构象.这些电极中,lac/NIPAM-co-BPCP-M WCNTs/GC(NIPAM-co-BPCP:N-烯丙基-1-苯甲酰基-3-苯基-4,5-2H-4-甲酰胺基吡唑-co-N-异丙基丙烯酰胺)在无氧PBS中发生直接电子转移的式电位(605mV)更接近漆酶活性中心的式电位(580mV),具有较快的异相电子转移速率(0.726s-1),较高的漆酶担载量(103.5mg/g)和固定漆酶比活力(1.68U/mg),较高的催化氧还原能力(氧还原起始电位820mV,在650mV时的催化峰电流为85.5μA)以及良好的重复使用性和长期使用性.     

咖啡酸玻碳修饰电极对烟酰胺腺嘌呤二核苷酸的电催化氧化

研究了咖啡酸修饰电极的制备、性质及对NADH的电催化作用。修饰电极在0．1mol/L PBS缓冲溶液中(pH7．0)于0．0～ 050V(vs.Ag／AgCl)电位范围内呈现一对氧化还原峰，式量电位(E^0‘‘)为 0．250V(vs．Ag／AgCl)。E^0‘‘随pH增加而朝负方向移动，pH在5．0～8．0范围内，其线性回归方程为E^0‘‘=0．6233-0．05996pH，R=0．9969。表观电极反应速率常数(Kb)为12．3s^-1。电极反应的电子数为2且有2个质子参与。该修饰电极对NADH的氧化具有很好的电催化作用。NADH浓度在0．1—6．0mmol／L．范围内与峰电流呈现良好的线性关系。文中对电催化过程进行了探讨。     

肉豆蔻酸-双层类脂膜修饰玻碳电极研究氯化血红素的电化学行为

报道了氯化血红素在肉豆蔻酸-双层类脂膜修饰玻碳电极上的电化学行为。在0.1~-0.7 V(vs.Ag/AgCl)电位范围内,扫描速率为40 mV/s时,氯化血红素在-0.4 V处产生很灵敏的还原峰电流。于pH7.50.01 mol/L KH2PO4-Na2HPO4底液中,该氧化峰电流与氯化血红素浓度在7.32×10-9~1.57×10-6mol/L范围内呈良好线性关系。该电极可作为检测氯化血红素的新型的高灵敏度电化学生物传感器。     

介孔碳掺杂氮材料-壳聚糖固定漆酶电极的直接电化学行为及化学传感性能

以壳聚糖和介孔碳氮材料共混所得复合物为固定漆酶的载体,将固酶复合物滴涂在裸玻碳电极表面并干燥后,得到固定漆酶基阴极.考察了此电极在不含底物的电解质溶液中的直接电化学行为,同时还研究了其对氧气还原反应的催化性能和电极的长期使用性、重现性和力学稳定性.在此基础上还考察了此电极作为氧气电化学传感器的性能.研究结果表明,介孔碳氮材料-壳聚糖固定漆酶修饰电极能在无任何电子中介体条件下,实现漆酶活性中心T1与电极之间的直接电子转移,而且能在较高的电位下实现氧气的电还原.此电极催化氧还原的起始电位约为860 mV,氧还原的半波电流密度约为78×10-6 A/cm2.这种漆酶基电极的重现性良好且具有优异的长期稳定性,但力学稳定性较差.此电极对氧的传感性能良好:检测限低达0.4 μmol/L,灵敏度高达(67.9×10-6A·L/mmol),具有良好的对氧亲和力(KM =764.0 μmol/L).     

阿魏酸聚合修饰玻碳电极的制备及其对NADH的催化氧化

研究了阿魏酸修饰电极的制备、性质及对NADH的电催化作用.该电极在0.1mol/L磷酸缓冲溶液(pH=6.60)中,于-0.1～+0.50V(vs.Ag/AgCl)电位范围内呈现一对氧化还原峰,其式量电位E₀为+0.188V(vs.Ag/AgCl),且E₀随pH增加而负向移动.电子转移系数为0.496,表观电极反应速率常数(ks)为6.6s^-1.电极反应的电子数为1且有1个质子参与.该修饰电极对NADH氧化具有很好的催化作用.在NADH存在下,电极过程由扩散控制,扩散系数为1.76×10^-6cm²/s.NADH浓度在0.01～5.0mmol/L范围内与峰电流呈现良好的线性关系.通过计时安培法测得催化速率常数为6.82×10³mol^-1·L·s^-1.     

固定漆酶聚苯胺-CoC2O4纳米复合物修饰电极的直接电化学

采用循环伏安法、微分脉冲伏安法、交流阻抗谱以及计时电流法等电化学方法,结合红外光谱、紫外-可见分光光度法、原子力显微镜、透射电子显微镜以及原子吸收光谱等辅助手段,表征了固定漆酶的聚苯胺-草酸钴纳米复合物的化学组成、结构和形貌,测试了纳米复合物固酶前后的导电性能的变化,研究了纳米复合物修饰电极上固定漆酶的直接电化学行为,评估了该电极的催化氧还原效能以及作为电化学传感器检测氧分子的性能。实验结果表明该电极在不含电子介体的溶液中以酶活性中心T2作为首要电子受体,将得到电子传递给化学吸附的氧气使其被电还原,其表观电子迁移速率为0.017 s^-1,且具有良好的催化氧还原性能（氧还原起始电位：460 mV vs NHE,转化氧分子为水的表观速率常数为2.6×10^-4 s^-1）,酶电催化氧还原为水分子步骤为反应的速控步。该电极作为电化学传感器对氧具有极低检测限（0.20 μmol·L^-1）,宽线性响应范围（0.4~7.5 μmol·L^-1）以及对底物高亲和力（K_M=122.4 μmol·L^-1）等优势。     

银掺杂聚L-酪氨酸修饰电极同时测定多巴胺、肾上腺素和抗坏血酸

用循环伏安法制备银掺杂聚L-酪氨酸修饰玻碳电极,研究了多巴胺、肾上腺素和抗坏血酸在其电极上的电化学行为,建立了同时测定多巴胺、肾上腺素和抗坏血酸的新方法。当3种组分共存时,在磷酸盐缓冲溶液(pH6.0)中,扫描速率为140mV/s,多巴胺和肾上腺素在修饰电极上分别产生还原峰,峰电位分别为0.198和-0.205V,多巴胺和肾上腺素氧化峰重叠,峰电位为0.313V(vs.Ag/AgCl);抗坏血酸产生一个氧化峰,峰电位0.108V(vs.Ag/AgCl)。多巴胺和肾上腺素的ΔEpc=0.403V,抗坏血酸的氧化峰与多巴胺和肾上腺素的ΔEpa=0.205V,用还原峰和氧化峰可同时测定多巴胺、肾上腺素和抗坏血酸,3种组分同时测定的线性范围分别为5.0×10-6～1.0×10-4mol/L,8.0×10-6～1.0×10-4mol/L和3.0×10-5～1.0×10-3mol/L;检出限分别为5.0×10-7,8.0×10-7和5.0×10-6mol/L。本方法用于人尿液中多巴胺、肾上腺素和抗坏血酸的同时测定,结果满意。     

碳糊电极上无机膜固载血红蛋白的直接电化学

报道了用硅溶胶-凝胶(Sol-gel)膜将血红蛋白(Hb)固载于碳糊电极上的直接电化学行为.研究结果表明,Hb-Sol-gel修饰的碳糊电极在pH=7.0的缓冲溶液中于-0.275V(vs.Ag/AgCl)处有一对可逆的循环伏安氧化-还原峰,为Hb血红素辅基Fe(Ⅲ)/Fe(Ⅱ)电对的特征峰.HbFe(Ⅲ)/Fe(Ⅱ)电对的式量电位在pH5.0～11.0范围内与溶液pH值呈线性关系,表明Hb的电化学还原很可能是一个质子伴随着一个电子的电极过程.FTIR光谱证实,Sol-gel膜对Hb的固载没有破坏其天然结构.Hb-Sol-gel修饰的碳糊电极能够催化还原H₂O₂,可望将其用于制作第三代生物传感器.     

Sol–gel synthesis of calcium hydroxyapatite thin films on quartz substrate using dip-coating and spin-coating techniques

Sol–gel synthesis route was suggested to prepare calcium hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂, CHA) thin films on quartz substrates. CHA thin films were obtained using dip-coating and spin-coating techniques by coating the substrates 1, 5, 15 and 30 times. In the sol–gel process, the ethylenediaminetetraacetic acid and 1,2-ethandiol as complexing agents were used. Moreover, triethanolamine and polyvinyl alcohol were used as gel network forming materials. After each coating procedure the films were annealed at 1,000 °C. The results obtained from dip-coating and spin-coating techniques were compared in this study. It was demonstrated, that the formation of calcium hydroxyapatite depends on dipping (or spinning) time and annealing duration.     

New approach to the quaternization of chitosan and its amphiphilic derivatives

Regioselective quaternization of chitosan and its amphiphilic derivatives has been carried out by means of reaction with betaine in the presence of the coupling reagent 2-ethoxy-1-ethoxycarbonyl-1,2-dihydroquinoline (EEDQ) in aqueous media at pH 5.5 ± 0.5. This reaction results in preparation of N-/(trimethylammonio)acetyl/chitosan chloride and its amphiphilic derivatives. The degree of quaternization increases with increasing EEDQ/chitosan ratio and is partly accompanied by N-ethoxycarbonylation. That side-product formation can be minimized by increasing betaine/EEDQ ratio.     

Preparation of benzoheterocycles containing a chlorofluoromethyl group using the ‘Yarovenko reagent’

ortho-Bifunctional benzenes such as 2-aminophenol o-phenylenediamine, 2-aminothiophenol, 2-aminobenzamide and catechol reacted very easily with 2-chloro-1,1,2-trifluoroethyldiethlylamine, the ‘Yarovenko reagent,’ affording 2-(chlorofluoromethyl)benzoxazole, -benzoimidazole, -benzothiazole, 2-(chlorofluoromethyl)-4-quinazolone and 2-diethylamino-2-(chlorofluoromethyl)dioxole respectively.     

New seven membered palladacycles: C-Br bond activation of 2-bromo-pyridine derivative by Pd(II)

C-Br bond activation followed by a C-C coupling reaction of the 2-bromo-pyridyl unit of [1-phenyl-2-(6-bromopyridin-2-yl)-benzoimidazole] was performed by Pd(CH(2)CMe(2)-o-C(6)H(4))(η(4)-COD). Two new seven membered palladacycles were obtained. A combined experimental and theoretical DFT study elucidates the mechanism for this reaction.     

甲壳素类液晶高分子的研究Ⅵ.邻苯二甲酰化壳聚糖中酰胺酸取代度对液晶性的影响

通过控制不同反应时间和邻苯二甲酸酐 壳聚糖的摩尔比制备不同取代度的邻苯二甲酰化壳聚糖(PHCS) .用FTIR研究了反应机理和产物结构 ,观察到PHCS含两类取代即酰胺酸取代和酰亚胺取代 .反应时间较短时主要为前者 ,取代度表示为DS1 ;反应时间较长时主要为后者 ,取代度表示为DS2 .对PHCS在二氯乙酸 (DCA)中的液晶行为观察 ,结果表明 ,PHCS的临界浓度随DS1 的增加而显著增加 .DS1 对PHCS临界浓度的影响明显大于DS2 的影响 .基本上为酰胺酸取代的PHCS的临界浓度高于溶解度 ,以至于观察不到     

Adsorption behavior of uranium(VI) and other ionic species on cross-linked chitosan resins modified with chelating moieties

Cross-linked chitosan resins with catechol (catechol-type chitosan, type 1 and type 2), iminodiacetic acid (IDA-type chitosan), iminodimetylphosphonic acid (IDP-type chitosan), phenylarsonic acid (phenylarsonic acid-type chitosan), or serine (serine-type chitosan) were prepared for the collection and concentration of uranium(VI). The adsorption behavior of U(VI) and other ionic species, such as metal ions and oxo-acid ions, on the cross-linked chitosan (base material) and chitosan resins modified with chelating moieties was examined using a column procedure. Especially, the catechol-type chitosan (type 2) adsorbed U(VI) at pH 2-7, and selectively collected U(VI) at acidic pH regions by forming a stable chelate with hydroxyl groups of catechol moiety introduced to the chitosan. Also, the adsorption properties of cationic and anionic species present in aquatic media were elucidated. The adsorption ability for U(VI) was in the order: catechol-type chitosan (type 2) > serine-type chitosan > phenylarsonic acid-type chitosan > the others. The catechol-type chitosan (type 2) was useful for the collection and concentration of uranium(VI).     

Layer by layer surface engineering of poly (lactide-co-glycolide) nanoparticles: A versatile tool for nanoparticle engineering for targeted drug delivery

Recent work regarding the Layer by Layer (LbL) engineering of poly(lactide-co-glycolide) nanoparticles (PLGA NPs) is reviewed here.The LbL engineering of PLGA NPs is applied as a means of generating advanced drug delivery devices with tailored recognition,protection,cargo and release properties.LbL in combination with covalent chemistry is used to attach PEG and folic acid to control cell uptake and direct it towards cancer cells.LbL coatings composed of chitosan and alginate show low protein interactions and can be used as an alternative to Pegylation.The assembly on top of LbL coatings of lipid layers composed of variable percentages of 1,2-dioleoyl-sn-glycero-3-choline (DOPC) and 1,2-dioleoyl-sn-glycero-3-phosphoL-serine (DOPS) increases NP uptake and directs the NPs towards the endoplasmic reticulum.The antibody anti-TNF-α is encapsulated forming a complex with alginate that is assembled LbL on top of PLGA NPs.The antibody is released in cell culture following first order kinetics.The release kinetics of encapsulated molecules inside PLGA NPs are studied when the PLGA NPs are coated via LbL with different polyelectrolytes.The intracellular release of encapsulated Doxorubicin is studied in the HepG2 cell line by means of Fluorescence Lifetime Imaging.     

On the Modification of Chitosan Through Grafting

Abstract

The feasibility of grafting poly(methyl acrylate) and poly[1-(methoxycarbonyl) ethylene] onto chitosan, poly-β(1←-4)-2-amino-2-deoxy-d-glucose, was investigated. The grafting reaction was carried out in aqueous solution by using ferrous ammonium sulfate (FAS) in combination with H₂O₂ as redox initiator. The effects of such reaction variables as chitosan, monomer and initiator concentrations, reaction time, and reaction temperature were determined. Through this study the grafting reaction could be optimized. The grafting yield reached its maximum value of 332% when 0.3 g chitosan was copolymerized with 3 mL monomer at 70°C for 120 minutes with [FAS] = 6 × 10^?5 M, [H₂O₂] = 6 × 10^?3 M, and 8 mL water. The grafted chitosan was found to be insoluble in solvents for chitosan and solvents for poly(methyl acrylate), but did show swelling in dilute acetic acid, methanol, acetone, and in an ethanol/2% acetic acid 1:1 mixture. The thermal stability of chitosan and grafted chitosan were studied by dynamic thermogravimetric analysis. The results show that the graft copolymer is thermally more stable than pure chitosan. The overall activation energy for graft copolymerization was estimated to be 32.8 kcal/mol.     

Über Chalkogenolate. 160. Umsetzung von 1,2-Ethandithiolaten mit Kohlenstoffdisulfid 2. 1,2-Ethan-bis(trithiokohlensäure) und Alkylester der Säure

On Chalcogenolates. 160. Reaction of 1,2-Ethanedithiolates with Carbon Disulfide. 2. 1,2-Ethane-bis(trithiocarbonic acid) and Alkyl Esters of This Acid The reaction of potassium 1,2-ethane-bis(trithiocarbonate) with hydrochloric acid at 0°C gives unstable, deep yellow coloured 1,2-ethane-bis(trithiocarbonic acid) The 1,2-ethane-bis(alkyl trithiocarbonates) RS? CS? SCH₂CH₂S? CS? SR, where R = CH₃ and C₂H₅, have been formed by reaction of potassium 1,2-ethane-bis(trithiocarbonate) with the corresponding alkyl iodide. The called compounds have been characterized by means of diverse spectroscopic methods.     

Characterization of sol-gel processing of calcium phosphate thin films on silicon substrate by FTIR spectroscopy

Calcium hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂, CHAp) films were obtained on silicon substrates by a sol-gel method using a spin-coating technique. In the sol-gel process, ethylendiamintetraacetic acid and 1,2-ethandiol, triethanolamine and polyvinyl alcohol were used as complexing agents and gel network forming agents, respectively. The samples were annealed at 1000 °C for 5 h in air after each spinning procedure. Spin-coating and annealing procedures were repeated 5, 8 and 10 times. The coatings were characterized using X-ray diffraction (XRD), scanning electron microscopy- energy dispersive X-ray spectroscopy (SEM-EDX) and Fourier Transform infrared spectroscopy (FTIR). FTIR-spectroscopy allowed us to predict the formation of oxyhydroxyapatite Ca₁₀(PO₄)₆(OH)_2-2xO_x on the Si substrate. Moreover, according to the FTIR results, the side phase β-Ca₃(PO₄)₂ has been formed instead of α-Ca₃(PO₄)₂. In addition, the anhydrous dicalcium, phosphate phase CaHPO₄ was also detected spectroscopically.