基于固定化电子媒介体的漆酶电极的制备与应用

采用一种新方法引入媒介体,即将媒介体2,2-连氮-双(3-乙基苯并噻唑啉-6-磺酸)(ABTS)固定在多壁碳纳米管(MWCNTs)上,将壳聚糖与漆酶共同修饰在玻碳电极表面,制备了漆酶电极。实验发现,ABTS能够被牢固地吸附在多壁碳纳米管上,且吸附了ABTS的多壁碳纳米管在水中的分散性能大为改善。由于ABTS的存在,该漆酶电极能够更加有效地催化氧气还原,使氧气的还原电位从-0.1 V升至0.6 V。研究了修饰在多壁碳纳米管上的ABTS的电化学行为,并讨论了碳纳米管修饰量、pH值及温度对漆酶电极催化性能的影响。该方法简单,制备的漆酶电极对氧气还原的催化效率高,有望应用于植入型生物燃料电池。     

壳聚糖-g-N-羧甲基-二（2-苯并咪唑）-1,2-乙二醇和纳米金溶胶复合物固定漆酶修饰玻碳电极的直接电化学

制备了壳聚糖-g-N-羧甲基-二（2-苯并咪唑）-1,2-乙二醇（CTS-g-N-CBBIE）,将其与纯化的纳米金溶胶（NGS）共混得到CTS-g-N-CBBIE-NGS复合物。 以此复合物作为固酶载体固定云芝漆酶,固酶量大（31.10 mg/g）,固酶比活力高（1.43 U/mg）;此固酶复合物修饰的玻碳电极在无氧磷酸盐-柠檬酸盐缓冲溶液（pH=5.0）中可以实现无中介酶-电极直接电子迁移（一对准可逆氧化还原峰式电位576 mV(vs.Ag/AgCl)对应于漆酶活性中心T1位的氧化还原）,电子迁移速率常数为228.3 s-1。 当氧气浓度较小时,这种固酶修饰电极对氧气还原具有一定的生物电催化性能（空气饱和缓冲溶液中氧还原峰电位约为320 mV(vs.Ag/AgCl)）。 当氧气浓度增高后,氧还原反应受到抑制;但这种漆酶修饰电极对pH较为敏感,且稳定性和重复使用性欠佳。     

介孔碳掺杂氮材料-壳聚糖固定漆酶电极的直接电化学行为及化学传感性能

以壳聚糖和介孔碳氮材料共混所得复合物为固定漆酶的载体,将固酶复合物滴涂在裸玻碳电极表面并干燥后,得到固定漆酶基阴极.考察了此电极在不含底物的电解质溶液中的直接电化学行为,同时还研究了其对氧气还原反应的催化性能和电极的长期使用性、重现性和力学稳定性.在此基础上还考察了此电极作为氧气电化学传感器的性能.研究结果表明,介孔碳氮材料-壳聚糖固定漆酶修饰电极能在无任何电子中介体条件下,实现漆酶活性中心T1与电极之间的直接电子转移,而且能在较高的电位下实现氧气的电还原.此电极催化氧还原的起始电位约为860 mV,氧还原的半波电流密度约为78×10-6 A/cm2.这种漆酶基电极的重现性良好且具有优异的长期稳定性,但力学稳定性较差.此电极对氧的传感性能良好:检测限低达0.4 μmol/L,灵敏度高达(67.9×10-6A·L/mmol),具有良好的对氧亲和力(KM =764.0 μmol/L).     

L-半胱氨酸/漆酶修饰的纳米金阴极对氧还原的电催化

以四氯金酸和L-半胱氨酸为原料,合成了L-半胱氨酸功能化纳米金粒子,将此纳米粒子修饰在金盘电极表面并共价偶联漆酶分子。 以循环伏安法研究了此固定漆酶电极在无氧磷酸盐缓冲液中电化学行为和催化氧还原能力,并进一步评估了其作为氧传感器使用的性能：以计时电流法测定其对氧气的检测限,与氧气的亲和力（以米氏常数表征）,研究了传感器的长期使用性、热稳定性和pH-催化电流关系。 结果表明,此固定漆酶电极可以实现漆酶活性中心T2与导电纳米粒子间的直接电子迁移而无需任何外加电子中介体（氧化还原峰的式电位为192.5 mV vs AgCl/Ag）,并在接近漆酶活性中心T3氧化还原式电位（780 mV vs NHE）附近发生氧还原;测得的固酶电极与氧气的亲和力较高（米氏常数为216.4 μmol/L）且检测限低达0.22 μmol/L,在4 ℃下保存60 d后活力仍然保持初始活力的大约78%。 但这种电极的热稳定性较差,受pH值影响较明显,在pH值近于生理条件时几乎完全丧失活力。     

金电极表面聚赖氨酸固定微过氧化物酶-11的电化学研究

通过聚赖氨酸修饰将微过氧化物酶-11(MP-11)固定在金电极表面,制备成MP-11修饰电极.修饰在电极表面上的MP-11的血红素活性中心与电极之间可进行直接的电子传递反应,其氧化还原式电位为-0.39V.该修饰电极对氧的还原具有电催化活性.当MP-11与咪唑发生轴向配位反应时,其氧化还原式电位发生负移,此时对氧的还原不再具有电催化活性.     

高分子聚合物-多壁碳纳米管复合物固定漆酶及其在玻碳电极上的直接电子迁移

采用不同结构的高分子聚合物与纯化的多壁碳纳米管(MWCNTs)共混的方法,制备得到聚合物非共价功能化多壁碳管复合物,测定了这些载体对漆酶(lac)的担载量、固定漆酶的比活力及稳定性.以固定漆酶的复合物修饰玻碳(GC)电极后,采用循环伏安法研究这些电极在无氧磷酸盐缓冲液(PBS)中的直接电化学行为及催化氧还原活力,粗略地测定了固定漆酶与电极间电子转移的速率常数.实验结果表明,当聚合物中含亲漆酶基团或能与漆酶活性中心发生相互作用的官能团时利于直接电子转移,而且复合物固定漆酶保持了游离漆酶的天然构象.这些电极中,lac/NIPAM-co-BPCP-M WCNTs/GC(NIPAM-co-BPCP:N-烯丙基-1-苯甲酰基-3-苯基-4,5-2H-4-甲酰胺基吡唑-co-N-异丙基丙烯酰胺)在无氧PBS中发生直接电子转移的式电位(605mV)更接近漆酶活性中心的式电位(580mV),具有较快的异相电子转移速率(0.726s-1),较高的漆酶担载量(103.5mg/g)和固定漆酶比活力(1.68U/mg),较高的催化氧还原能力(氧还原起始电位820mV,在650mV时的催化峰电流为85.5μA)以及良好的重复使用性和长期使用性.     

乳过氧化物酶与伴刀豆球蛋白A共修饰电极的电化学活性研究

用乳过氧化物酶(LPO)和伴刀豆球蛋白A(Con A)共修饰金电极,首次得到了乳过氧化物酶的直接电化学响应,在此基础上研究了乳过氧化物酶对过氧化氢(H2O2)的电催化活性,并研究了一氧化氮(NO)对LPO电催化活性的影响.在Con A的作用下,乳过氧化物酶在循环伏安图中显示1对准可逆的氧化还原峰,表现出薄层电化学行为.在pH 7.4的磷酸缓冲溶液中的表观氧化还原电位为 -190 mV.该共修饰电极对H2O2表现出电催化还原活性,由此构建的传感器对H2O2的检测范围是2.0×10-5 ～4.0×10-3 mol/L.实验发现,微摩尔量级的NO会抑制乳过氧化物酶对H2O2的催化活性.     

固定漆酶聚苯胺-CoC2O4纳米复合物修饰电极的直接电化学

采用循环伏安法、微分脉冲伏安法、交流阻抗谱以及计时电流法等电化学方法,结合红外光谱、紫外-可见分光光度法、原子力显微镜、透射电子显微镜以及原子吸收光谱等辅助手段,表征了固定漆酶的聚苯胺-草酸钴纳米复合物的化学组成、结构和形貌,测试了纳米复合物固酶前后的导电性能的变化,研究了纳米复合物修饰电极上固定漆酶的直接电化学行为,评估了该电极的催化氧还原效能以及作为电化学传感器检测氧分子的性能。实验结果表明该电极在不含电子介体的溶液中以酶活性中心T2作为首要电子受体,将得到电子传递给化学吸附的氧气使其被电还原,其表观电子迁移速率为0.017 s~(-1),且具有良好的催化氧还原性能(氧还原起始电位:460 m V vs NHE,转化氧分子为水的表观速率常数为2.6×10-4 s~(-1)),酶电催化氧还原为水分子步骤为反应的速控步。该电极作为电化学传感器对氧具有极低检测限(0.20μmol·L~(-1)),宽线性响应范围(0.4~7.5μmol·L~(-1))以及对底物高亲和力(KM=122.4μmol·L~(-1))等优势。     

一氧化氮在肌红蛋白修饰电极上的电催化还原

本文研究了醋酸盐缓冲体系中NO_2~-歧化产物NO在肌红蛋白修饰玻碳电极上的电催化还原反应,其还原峰电位为-0.68V(vs.SCE).文中考察了溶液酸度、亚硝酸根离子浓度等对修饰电极的电化学行为的影响,并对一氧化氮在肌红蛋白修饰电极上的电催化还原机理进行了探讨.     

水系体系中CO2在稀土(Nd)(Ⅲ)双酞菁修饰电极上的电催化还原研究

探讨了CO_2在稀土(Nd)(Ⅲ)双酞菁修饰电极上的电催还原行为。通过滴涂法将稀土(Nd)(Ⅲ)双酞菁担载在玻碳电极上制备成它的修饰电极,在水溶液中利用循环伏安、红外光谱法等方法研究制备的修饰电极对CO_2的电催化还原性能。结果表明,所制备的稀土(Nd)(Ⅲ)双酞菁修饰电极对CO_2的电催化还原有较高的活性,还原电流随修饰量增加而变大,修饰电极的还原电流与溶液的pH值有关,随着pH值变大,还原峰向负方向移动。实验结果表明,稀土(Nd)(Ⅲ)双酞菁修饰电极对二氧化碳电化学还原具有很好的电催化活性,在该修饰电极上,CO_2可在较正的电位下被还原。     

The Direct Electron Transfer of Iron‐Containing Superoxide Dismutase (Fe‐SOD) and its Catalysis for the Oxygen Reduction Reaction (ORR) in Room Temperature Ionic Liquids (RTILs) on a Gold Electrode

In this work, for the first time, the direct electron transfer of iron‐containing superoxide dismutase (Fe‐SOD) was observed by cyclic voltammetry on a gold (Au) electrode in three RTILs, i.e., 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIBF₄), 1‐n‐propyl‐3‐methylimidazolium tetrafluoroborate (PMIBF₄) and 1‐n‐butyl‐3‐methylimidazolium tetrafluoroborate (BMIBF₄). And the results demonstrate that when the scan rate was as low as 1 mV/s, a pair of well‐defined quasi‐reversible peaks of Fe‐SOD was presented, while as the potential scan rate was above 10 mV/s, the reduction peak of Fe‐SOD disappeared though its oxidation peak could be clearly observed even as the potential scan rate was up to 400 mV/s, strongly indicating that these CVs we observed were attributable to Fe‐SOD rather than the impurities in RTILs. Its catalysis for oxygen reduction reaction (ORR) was directly verified by the shifting of formal potential, E⁰′, of ORR, to the positive direction though the value of standard rate constant, κ⁰, corresponding to ORR, was not much enhanced. In PMIBF₄, for the multi‐walled carbon nanotubes (MWCNTs)‐modified gold electrode, both the reduction peak current and oxidation peak current for oxygen redox reaction were all dramatically enhanced compared to the case of a bare gold electrode, and the value of κ⁰ was also increased from 3.1 × 10^?3 cm s^?1 for the bare gold electrode, to 17.5 × 10^?3 cm s^?1. Hence, in the presence of Fe‐SOD in RTILs, MWCNTs, showing catalysis for the electron transfer process of ORR, coupled with Fe‐SOD, leading to the shifting of formal potential corresponding to ORR to the positive direction, presented us a satisfactory catalysis for ORR in RTILs. Some reasons available for this catalysis behavior stemming from Fe‐SOD, and MWCNTs as well, for ORR are discussed based on the previously developed proposition.     

高耐甲醇性和稳定性的纳米复合阴极催化剂

报导了一种由酞菁氧钛、铂金属纳米簇和氮杂化碳纳米角结构基元组装而成的新型纳米复合电化学催化剂(TiOPc-Pt/NSWCNH)的制备、表征及电催化性能. 在TiOPc-Pt/NSWCNH催化剂中, 氮杂化碳纳米角堆积形成多孔导电网络, 铂纳粒子均匀地分散于上述多孔导电网络中, 部分铂纳粒子与TiOPc微晶直接接触. 在甲醇存在的条件下, TiOPc-Pt/NSWCNH对氧还原反应表现出高催化活性和优良的选择性与稳定性. 在甲醇浓度为0.5 mol·L^-1的高氯酸水溶液中, TiOPc-Pt/NSWCNH催化氧还原反应的起始电位比商购Pt/C-JM催化剂提高了260 mV, 其质量活性和比活性(0.85 V (参比电极为可逆氢电极(RHE)))分别为83.5 A·g^-1和0.294 mA·cm^-2, 远高于Pt/C-JM催化剂. 在含氧气氛下, 于甲醇高氯酸水溶液中, 对TiOPc-Pt/NSWCNH和TiOPc-Pt/C催化剂进行了循环伏安法加速老化实验研究(0.6-1.0 V, 15000个循环), 结果表明TiOPc-Pt/NSWCNH具有更高的稳定性. TiOPc-Pt/NCNH催化剂的高耐醇性可能得益于由TiOPc微晶向Pt纳米粒子的电子转移, 其高稳定性主要得益于氮杂化碳纳米角的高石墨化程度及纳米角堆积而成网络结构.     

聚苯并咪唑-漆酶复合物修饰电极无电子传递媒介体催化氧还原性能

采用循环伏安法将聚苯并咪唑和漆酶的复合物共沉积在玻碳电极表面。 制备的漆酶基电极在O2气饱和的磷酸盐缓冲液中可以观察到明显的催化还原电流,实现了无媒介体的酶-电极间直接电子迁移,电极静止时氧还原起始电位为645 mV,近于漆酶活性位T1的式电位580 mV,而极限扩散催化电流密度可达318.5×10-6 A/cm2。 但由于O2气在致密的固酶导电聚合物修饰层中扩散不够快(扩散系数只有在溶液中的1.25％),导致电极以较高速度旋转时极限扩散催化电流密度仅仅增加到1×10-3 A/cm2。 根据静态时极限催化电流密度求算得到的固定漆酶催化氧还原平均转化率为21.7/s。 这种漆酶基电极具有良好的重现性和长期使用性(储存10 d后催化活力仍然保持了初始值的80％以上),在人体生理温度和弱酸性条件下具有最佳催化活力。 这种漆酶基电极作为氧传感器具有良好的传感性能：检测限低(0.5 μmol/L),灵敏度高(71.1 μA·L/mmol),且对O2具有良好的亲和力(KM=89.9 μmol/L)。     

吡啶掺杂碳载钴酞菁催化氧还原的电化学性能及在燃料电池中的应用

以碳黑(Vulcan XC-72R)为载体, 吡啶(Py)和钴酞菁(CoPc)为催化剂前驱体, 经溶剂分散法制备了Py掺杂碳负载纳米钴酞菁复合催化剂(Py-CoPc/C). 通过扫描电镜-能谱分析(SEM-EDS)、X射线光电子能谱(XPS)分析和X射线衍射(XRD)分析技术对催化剂的组成和微观结构进行了表征, 并运用线性扫描循环伏安法(LSV)和旋转圆盘电极(RDE)技术考察了不同Py掺杂含量对碳载钴酞菁(CoPc/C)催化氧还原反应(ORR)活性的影响及稳定性. 结果显示: Py掺杂可以明显改善CoPc/C 对ORR的电催化性能, 其中掺杂20%Py下所制备的20%Py-20%CoPc/C 催化剂对ORR表现出最佳的催化活性, 以其制备的气体扩散电极在O₂气氛饱和的0.1 mol·L^-1 KOH 电解质溶液中, 0.2 V (相对于标准氢电极)即可产生明显的氧还原电流, 半波电位为-0.03 V. 相比于40%Py/C 和未掺杂的40%CoPc/C, 20%Py-20%CoPc/C催化剂的半波电位分别正移了160 和15 mV. 进一步运用RDE理论研究表明, 在Py-CoPc/C 电极上ORR的电子转移总数为2.38, 高于CoPc/C电极上的电子转移总数1.96, 从而使ORR的选择性明显提高. SEM-EDS和XRD分析表明Py掺杂提高了CoPc/C催化剂的分散性和N含量, 更利于O₂的吸附. XPS分析表明: 吡啶结构的N与石墨结构的N均存在于Py-CoPc/C 催化剂中,与催化剂表面的Co离子配位可能是促使ORR活性提高的原因. 最后以20%Py-20%CoPc/C制备了膜电极组装(MEA)电极, 应用于H₂/O₂ 燃料电池单电池发电, 室温下获得最大发电功率密度为21 mW·cm^-2, 相对于CoPc/C提高至2.4倍.     

Direct electron transfer of cytochrome C and its electrocatalytic properties on multiwalled carbon nanotubes/ciprofloxacin films

In this study, stable and homogenous thin films of multiwalled carbon nanotubes (MWCNTs) were obtained on conducting surface using ciprofloxacin (CF, fluoroquinolone antibiotic) as an effective-dispersing agent. Further, MWCNTs/CF film modified electrodes (glassy carbon and indium tin oxide-coated glass electrode) are used successfully to study the direct electrochemistry of proteins. Here, cytochrome C (Cyt-C) was used as a model protein for investigation. A MWCNTs/CF film modified electrode was used as a biocompatible material for immobilization of Cyt-C from a neutral buffer solution (pH 7.2) using cyclic voltammetry (CV). Interestingly, Cyt-C retained its native state on the MWCNTs/CF film. The Cyt-C adsorbed MWCNTs/CF film was characterized by scanning electron microscopy (SEM), UV–visible spectrophotometry (UV-vis) and CV. SEM images showed the evidence for the adsorption of Cyt-C on the MWCNTs/CF film, and UV–vis spectrum confirmed that Cyt-C was in its native state on MWCNTs/CF film. Using CV, it was found that the electrochemical signal of Cyt-C was highly stable in the neutral buffer solution and its redox peak potential was pH dependent. The formal potential (−0.27 V) and electron transfer rate constant (13 ± 1 s⁻¹) were calculated for Cyt-C on MWCNTs/CF film modified electrode. A potential application of the Cyt-C/MWCNTs/CF electrode as a biosensor to monitor H₂O₂ has been investigated. The steady-state current response increases linearly with H₂O₂ concentration from 2 × 10⁻⁶ to 7.8 × 10⁻⁵ M. The detection limit for determination of H₂O₂ has been found to be 1.0 × 10⁻⁶ M (S/N = 3). Thus, Cyt-C/MWCNTs/CF film modified electrode can be used as a biosensing material for sensor applications.     

Evaluation of graphene oxide and reduced graphene oxide in the immobilization of laccase enzyme and its application in the determination of dopamine

Bioelectrodes were developed based on a simple deposition of graphene oxide (GO) or reduced graphed oxide (rGO) and laccase (Lac) on a glassy carbon (GC) electrode surface. The morphology and electrochemical behavior of the biosensors were characterized by scanning electron microscopy and cyclic voltammetry. These results demonstrated that only rGO was successfully applied for the immobilization of the laccase enzyme, improving the analytical signal for the determination of dopamine. The GC/rGO/Lac biosensor was applied to the detection of dopamine in synthetic urine and plasmatic serum samples, achieving a detection limit of 91.0 nmol L^?1.     

Study on Glucose Biofuel Cells Using an Electrochemical Noise Device

An electrochemical noise (ECN) device was utilized for the first time to study and characterize a glucose/O₂ membraneless biofuel cell (BFC) and a monopolar glucose BFC. In the glucose/O₂ membraneless BFC, ferrocene (Fc) and glucose oxidase (GOD) were immobilized on a multiwalled carbon nanotubes (MWCNTs)/Au electrode with a gelatin film at the anode; and laccase (Lac) and an electron mediator, 2,2′‐azinobis (3‐ethylbenzothiazoline‐6‐sulfonate) diammonium salt (ABTS), were immobilized on a MWCNTs/Au electrode with polypyrrole at the cathode. This BFC was performed in a stirred acetate buffer solution (pH 5.0) containing 40 mmol/L glucose in air, with a maximum power density of 8 μW/cm², an open‐circuit cell voltage of 0.29 V, and a short‐circuit current density of 85 μA/cm², respectively. The cell current at the load of 100 kΩ retained 78.9% of the initial value after continuous discharging for 15 h in a stirred acetate buffer solution (pH 5.0) containing 40 mmol/L glucose in air. The performance decrease of the BFC resulted mainly from the leakage of the ABTS mediator immobilized at the cathode, as revealed by the two‐channel quartz crystal microbalance technique. In addition, a monopolar glucose BFC was performed with the same anode as that in the glucose/O₂ membraneless BFC in a stirred phosphate buffer solution (pH 7.0) containing 40 mmol/L glucose, and a carbon cathode in Nafion‐membrane‐isolated acidic KMnO₄, with a maximum power density of 115 μW/cm², an open‐circuit cell voltage of 1.24 V, and a short‐circuit current density of 202 μA/cm², respectively, which are superior to those of the glucose/O₂ membraneless BFC. A modification of the anode with MWCNTs for the monopolar glucose BFC increased the maximum power density by a factor of 1.8. The ECN device is highly recommended as a convenient, real‐time and sensitive technique for BFC studies.     

Preparation and characterization of MnO<Subscript>2</Subscript>/MWCNTs-modified graphite electrode and its catalysis for oxygen reduction reaction (ORR)

Manganese dioxides were prepared onto multi-walled carbon nanotubes (MWCNTs) by cyclic voltammetry (CV). The obtained manganese oxide-MWCNTs (MnO₂/MWCNTs) samples were characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), fourier transform infrared spectrometry (FTIR) and thermogravimetry (TG), respectively. The MnO₂/MWCNTs-modified graphite electrode was utilized in the electrochemical oxygen reduction reaction (ORR) and the enhanced oxygen reduction peak current strongly suggested that MnO₂/MWCNTs has catalysis for ORR when compared to the pure MnO₂ or MWCNTs. The catalysis mechanism of MnO₂/MWCNTs for ORR was also-discussed.     

Enhanced Four-Electron Selective Oxygen Reduction Reaction at Carbon-Nanotube-Supported Sulfonic-Acid-Functionalized Copper Phthalocyanine

In the present work, the oxygen reduction reaction (ORR) is explored in an acidic medium with two different catalytic supports (multi-walled carbon nanotubes (MWCNTs) and nitrogen-doped multi-walled carbon nanotubes (NMWCNTs)) and two different catalysts (copper phthalocyanine (CuPc) and sulfonic acid functionalized CuPc (CuPc-SO₃⁻)). The composite, NMWCNTs-CuPc-SO₃⁻ exhibits high ORR activity (assessed based on the onset potential (0.57 V vs. reversible hydrogen electrode) and Tafel slope) in comparison to the other composites. Rotating ring disc electrode (RRDE) studies demonstrate a highly selective four-electron ORR (less than 2.5 % H₂O₂ formation) at the NMWCNTs-CuPc-SO₃⁻. The synergistic effect of the catalyst support (NMWCNTs) and sulfonic acid functionalization of the catalyst (in CuPc-SO₃⁻) increase the efficiency and selectivity of the ORR at the NMWCNTs-CuPc-SO₃⁻. The catalyst activity of NMWCNTs-CuPc-SO₃⁻ has been compared with many reported materials and found to be better than several catalysts. NMWCNTs-CuPc-SO₃⁻ shows high tolerance for methanol and very small deviation in the onset potential (10 mV) between the linear sweep voltammetry responses recorded before and after 3000 cyclic voltammetry cycles, demonstrating exceptional durability. The high durability is attributed to the stabilization of CuPc-SO₃⁻ by the additional coordination with nitrogen (Cu-N_x) present on the surface of NMWCNTs.     

氮化钨-钨/掺氮有序介孔碳复合材料的制备及其氧还原性能

采用软模板法制备了氮化钨-钨/掺氮有序介孔碳复合材料(WN-W/NOMC),作为一种高比表面积且价格低廉的阴极氧还原反应催化剂。通过适量添加尿素来改变复合材料中的氮含量,在掺氮量为7%(w/w)时,实验发现材料能够保持完整有序介孔结构,测试其比表面积高达835 m~2·g~(-1),透射电子显微镜(TEM)测试结果显示其催化颗粒均匀地分散在氮掺杂有序介孔碳载体上。在O_2饱和的0.1 mol·L~(-1 )KOH溶液中测试了材料的氧还原催化性能(ORR),显示其起始电位为0.87 V(vs RHE),极限电流密度为4.49 mA·cm~(-2),氧还原反应的转移电子数为3.4,接近于20%(w/w)商业Pt/C的3.8,说明该材料表现出近似4电子的氧还原反应途径。研究结果表明,WN-W/NOMC的催化性能虽然稍弱于商业铂碳(0.99 V,5.1 mA·cm~(-2)),但其具有远超铂碳的循环稳定性和耐甲醇毒化能力。