“LIVING”/CONTROLLED RADICAL POLYMERIZATION OF ETHYL METHYLACRYLATE WITH 2,2’-AZOBISISOBUTYRONITRILE/FERRIC CHLORIDE/TRIPHENYLPHOSPHINE INITIATION SYSTEM

"Living"/controlled radical polymerization of ethyl methacrylate (EMA) was carried out with a 2,2'-azobisisobutyronitrile (AIBN)/ferric chloride (FeCl_3)/triphenylphosphine (PPh_3) initiation system at 85℃. Thc numberaverage molecular weight (M_n) increases linearly with monomer conversion and the rate of polymerization is first order withrespect to monomer concentration. The M_w of PEMA ranges from 3900 to 17600 and the polydispersity indices are quitenarrow (1.09～1.22). The conversion can reach up to～100% and M_w of the polymers obtained is close to that designed. Thepolymerization mechanism belongs to the reverse atom transfer radical polymerization (ATRP). The polymer was end-functionalized by chlorine atom, which acts as a macroinitiator to proceed extension polymerization in the presence ofCuBr/bipy catalyst system via an ATRP process. The presence of ω-chlorine in the PEMA obtained was identified by ~1H-NMR spectrum.     

Living carbocationic copolymerization of isobutylene with styrene

The carbocationic copolymerization of isobutylene (IB) and styrene (St), initiated by 2‐chloro‐2,4,4‐trimethylpentane/TiCl₄ in 60/40 (v/v) methyl chloride/hexane at ?90 °C, was investigated. At a low total concentration (0.5 mol/L), slow initiation and rapid monomer conversion were observed. At a high total comonomer concentration (3 mol/L), living conditions (a linear semilogarithmic rate and M_n–conversion plots) were found, provided that the St concentration was above a critical value ([St]₀ ～ 0.6 mol/L). The breadth of the molecular weight distribution decreased with increasing IB concentration in the feed, reaching M_w/M_n ～ 1.1. St homopolymerization was also living at a high total concentration, yielding polystyrene with M_n = 82,000 g/mol, the highest molecular weight ever achieved in carbocationic St polymerization. An analysis of this system by both the traditional gravimetric–NMR copolymer composition method and FTIR demonstrated penultimate effects. IB enrichment was found in the copolymers at all feed compositions, with very little drift at a high total concentration and above the critical St concentration. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1778–1787, 2007     

Aqueous polymerization of methyl methacrylate initiated by the redox system Ce(IV)–isopropyl alcohol. Kinetics and molecular weight

Polymerization of methyl methacrylate was carried out in aqueous nitric acid in the temperature range 26–40°C, with the redox initiator system ceric ammonium nitrate–isopropyl alcohol. A short induction period was observed, as well as the attainment of a limiting conversion, and the total ceric ion consumption with reaction time. The reaction orders were 1/2 and 3/2 with respect to the IPA and monomer concentration, respectively, within the range (3–5) × 10^?3M of Ce(IV). But at lower Ce(IV) concentration (≤ 1 × 10^?3M), the order with respect to monomer and Ce(IV) changed to 1 and 1/2, respectively. The rate of ceric ion disappearance was first order with respect to Ce(IV) concentration and (R_Ce)^?1 was proportional to [IPA]^?1. Both the rate of polymerization and the rate of ceric ion consumption increase with rise in temperature. The average-molecular weight can be controlled by variations in IPA, Ce(IV), and monomer concentrations, and in temperature. A kinetic scheme involving oxidation of IPA by Ce(IV) via complex formation, whose decomposition gives rise to a primary radical, initiation, propagation, and termination of the polymeric radicals by bimolecular interaction is proposed. An oxidative termination of primary radicals by Ce(IV) is also included.     

Free Radical Copolymerization of N‐(4‐Carboxyphenyl)maleimide with Hydropropyl Methacrylate

Abstract

The free radical copolymerization of N‐(4‐carboxyphenyl)maleimide (CPMI) (M₁) with hydropropyl methacrylate (HPMA) (M₂) was carried out with 2,2′‐azobis(isobutyronitrile) (AIBN) as an initiator in ethyl acetate at 75°C. The composition of copolymer prepared at low conversion was determined by elemental analysis. The monomer reactivity ratios were found to be r ₁?=?0.31 and r ₂?=?1.11 as determined by the YBR equation. The number‐average molecular weight and polydispersity were determined by gel permeation chromatography (GPC). Furthermore, the solvent effect on this copolymerization system was also investigated. The resulting copolymer was characterized by FTIR and ¹H‐NMR spectroscopy. The thermal stability of copolymers was determined by thermogravimetric analysis (TGA). It was found that the copolymer shows step‐by‐step degradation, the initial decomposition temperature (T _i), and final decomposition temperature (T _f) increased with increasing the component of CPMI in copolymer.     

Propagation Mechanism of Radical Copolymerization of Sulfur Dioxide and Vinyl Chloride

Radical copolymerization of sulfur dioxide and vinyl chloride (VC) has been studied by the comparison of the composition of copolymers obtaining from different reaction conditions, i.e., reaction temperatures, feed compositions, and total monomer concentrations. The composition of VC in copolymer is independent of comonomer composition except at high concentration of VC in feed; it increases with increasing reaction temperature or decreasing total monomer concentration. At lower temperature, the composition of copolymer becomes independent of total monomer concentration. The overall rate of polymerization is proportional to [VC]^1,7 and [SO₂]^0.5. These results were compared with those obtained in our previous study on the SO₂-styrene copolymerization. A propagation mechanism for radical copolymerization of SO₂ and VC is also proposed.     

NOVEL COPOLYMERS OF TRISUBSTITUTED ETHYLENES WITH STYRENE. I. 2-HALOPHENYL-1,1-DICYANOETHYLENES

Electrophilic trisubstituted ethylene monomers, 2-halophenyl-1,1-dicyanoethylenes, RC₆H₄CH=C(CN)₂ (where R is o-Cl, m-Cl, p-Cl, p-Br, and p-F) were prepared and copolymerized with styrene. The monomers were synthesized by the piperidine catalyzed Knoevenagel condensation of ring-substituted benzaldehydes and malononitrile, and characterized by CHN elemental analysis, IR, ¹H and ¹³C-NMR. All the ethylenes were copolymerized with styrene (M₁) in solution with radical initiation (AIBN) at 70°C. The compositions of the copolymers were calculated from nitrogen analysis and the structures were analyzed by IR, ¹H and ¹³C-NMR. The order of relative reactivity (1/r ₁) for the monomers is p-Cl (14.8) >m-Cl (2.67)> o-Cl (1.82) > p-Br (1.52) > p-F (1.36). High T _g's of the copolymers (> 150°C) in comparison with that of polystyrene indicate a substantial decrease in the chain mobility of the copolymers due to the high dipolar character of the trisubstituted monomer unit. Gravimetric analysis indicated that the copolymers decompose in the range 300–400°C.     

RING OPENING COPOLYMERIZATION OF SUCCINIC ANHYDRIDE-ETHYLENE OXIDE BY Al(Ⅲ) ORGANOMETALLIC CATALYSTS

Ring opening copolymerization of succinic anhydride (SA) with ethylene oxide (EO)was successfully carried out by using a series of aluminum-based catalyst in 1,4-dioxane at62±2℃. The results showed that in-situ AlR_3-H_2O (R=ethyl, iso-butyl) catalysts gavehigher molecular weight (M_w～10~4), while Al(OR)_3 catalysts gave the higher alternatingcopolymer structure with slightly lower molecular weight. The in-situ AlR_3-H_2O systemshave been evaluated in more detail for the reaction which showed the optimum H_2O/Almolar ratio to be 0.5. The copolymers with different composition (F_(SA)/F_(EO)= 36/64to 45/55 mol/mol) were synthesized by using different monomer feed ratio. The melt-ing point (T_m), glass transition temperature (T_g) and enthalpy of fusion (ΔH_f) of thesecopolymers are depended on the copolymer composition and in the range of 87～102℃,-12～-18℃, and 37～66J/g, respectively. The second heating scan of DSC also in-dicated that the higher alternating copolymer was more easily recrystallized. The onsetdecomposition temperature was more than 300℃ under nitrogen and influenced by thecopolymer composition.     

Synthesis and Characterization of Poly(Diallyldimethylammonium Chloride-g-Acrylamide)

Graft copolymers of poly(diallyldimethylammonium chloride), (poly-DADMAC), with acrylamide were synthesized using a ceric salt/nitric acid initiation system. The effects of concentration of initiator, monomer, and substrates were studied. Copolymers were characterized by viscometry and size-exclusion chromatography. The highest molecular weight ( M _w ) of graft copolymer obtained was 1.70 × 10⁶. The compositions of copolymers are dependent upon the ratios of the concentration of monomer to the concentration of substrate. The highest content of DADMAC monomer unit in the copolymer was 33 wt%.     

Anionic Copolymerization of Carbonyl Sulfide with Epoxides via Alkali Metal Alkoxides

Carbonyl sulfide (COS), an analogue of carbon dioxide (CO₂), can be converted to CO₂ via the carbonic anhydride enzymes widely existing in nature. COS is an ideal monomer for making poly(monothiocarbonate)s, which are difficult to synthesize by traditional methods. Herein, for the first time, we describe an anionic copolymerization of COS with epoxides using alkali metal alkoxides as the catalysts (initiators), affording poly(monothiocarbonate)s with 100% alternating degree, >99% tail‐to‐head (T‐H) content, high number‐average molecular weights (M_ns, up to 90.3 kg/mol) with narrow molecular weight distributions (Đ=M_w/M_n, 1.05—1.31 for COS/propylene oxide copolymers) under solvent‐free and mild conditions. Oxygen‐sulfur exchange reaction (O/S ER), which can result in the production of contaminated dithiocarbonate and carbonate units in the main chain, was nearly completely depressed at 0 ^oC. In addition, in contrast to previously reported salen chromium (iron) complexes that required multiple synthetic steps, this work provides simple, low‐cost, and effective catalysts for making colorless sulfur‐containing polymers.     

Atom transfer radical polymerization of acrylates in an ionic liquid: Synthesis of block copolymers

Atom transfer radical polymerization (ATRP) of acrylates in ionic liquid, 1‐butyl‐3‐methylimidazolium hexaflurophospate, with the CuBr/CuBr₂/amine catalytic system was investigated. Sequential polymerization was performed by synthesizing AB block copolymers. Polymerization of butyl acrylate (monomer that is only partly soluble in an ionic liquid forming a two‐phase system) proceeded to practically quantitative conversion. If the second monomer (methyl acrylate) is added at this stage, polymerization proceeds, and block copolymer formed is essentially free of homopolymer according to size exclusion chromatographic analysis. The number‐average molecular weight of the copolymer is slightly higher than calculated, but the molecular weight distribution is low (M_w/M_n = 1.12). If, however, methyl acrylate (monomer that is soluble in an ionic liquid) is polymerized at the first stage, then butyl acrylate in the second‐stage situation is different. Block copolymer free of homopolymer of the first block (with M_w/M_n = 1.13) may be obtained only if the conversion of methyl acrylate at the stage when second monomer is added is not higher than 70%. Matrix‐assisted laser desorption/ionization time‐of‐flight analysis confirmed that irreversible deactivation of growing macromolecules is significant for methyl acrylate polymerization at a monomer conversion above 70%, whereas it is still not significant for butyl acrylate even at practically quantitative conversion. These results show that ATRP of butyl acrylate in ionic liquid followed by addition of a second acrylate monomer allows the clean synthesis of block copolymers by one‐pot sequential polymerization even if the first stage is carried out to complete conversion of butyl acrylate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2799–2809, 2002     

ATRP of methyl methacrylate initiated with a bifunctional initiator bearing bromomethyl functional groups: Synthesis of the block and graft copolymers

This article reports the synthesis of the block and graft copolymers using peroxygen‐containing poly(methyl methacrylate) (poly‐MMA) as a macroinitiator that was prepared from the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in the presence of bis(4,4′‐bromomethyl benzoyl peroxide) (BBP). The effects of reaction temperatures on the ATRP system were studied in detail. Kinetic studies were carried out to investigate controlled ATRP for BBP/CuBr/bpy initiating system with MMA at 40 °C and free radical polymerization of styrene (S) at 80 °C. The plots of ln ([M_o]/[M_t]) versus reaction time are linear, corresponding to first‐order kinetics. Poly‐MMA initiators were used in the bulk polymerization of S to obtain poly (MMA‐b‐S) block copolymers. Poly‐MMA initiators containing undecomposed peroygen groups were used for the graft copolymerization of polybutadiene (PBd) and natural rubber (RSS‐3) to obtain crosslinked poly (MMA‐g‐PBd) and poly(MMA‐g‐RSS‐3) graft copolymers. Swelling ratio values (q_v) of the graft copolymers in CHCl₃ were calculated. The characterizations of the polymers were achieved by Fourier‐transform infrared spectroscopy (FTIR), ¹H‐nuclear magnetic resonance (¹H NMR), gel‐permeation chromatography (GPC), differential scanning calorimetry (DSC), thermogravimetric analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), and the fractional precipitation (γ) techniques. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1364–1373, 2010     

Copolymers of p-Nitrobenzyl Acrylate with Methyl Acrylate: Synthesis,Characterization, and Monomer Reactivity Ratios

Abstract

Copolymers of p-nitrobenzyl acrylate and methyl acrylate with different feed ratios are synthesized in ethyl methyl ketone using benzoyl peroxide as a free radical initiator at 70 ± 1°C. The copolymers were characterized by IR and ¹H-NMR spectroscopic techniques. Copolymer compositions were determined by ¹H-NMR analysis of the polymers. The monomer reactivity ratios were determined by the application of conventional linearization methods such as Fineman–Ross and Kelen–Tüdös. Gel permeation chromatography was used for determining the molecular weights M _n and M _w, and the polydispersity index. The intrinsic viscosities and the thermal properties of the homo- and copolymers are also discussed.     

Segmented conjugated macromolecules containing silicon and boron: ADMET synthesis and luminescent properties

Boron‐ and silicon‐containing conjugated homo‐ and copolymers could be synthesized using acyclic diene metathesis (ADMET) condensation of bis‐styryl monomers. Both, tri‐and tetra‐coordinated boron monomers were successfully polymerized forming homopolymers, or random copolymers (if polymerized together with a silicon containing co‐monomer). Polymer molecular weights M_n were measured at ～6000 to 15,000 g/mol (NMR end group analysis) with molecular weight distributions M_w/M_n ～1.8 to 2.2. The polymers absorbed at λ_max ～317 to 406 nm and emitted at λ_max ～370 to 494 nm with fluorescent quantum efficiencies ～24 to 48%. The copolymer with tri‐coordinate boron showed highly efficient fluorescence quenching in the presence of fluoride ions at ratios boron/fluoride ～5/1, demonstrating its potential as anion sensor. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1707–1718     

Modeling the Effects of Primary Radicals in Free‐Radical Polymerization

The effects of non‐ideal initiator decomposition, i.e., decomposition into two primary radicals of different reactivity toward the monomer, and of primary radical termination, on the kinetics of steady‐state free‐radical polymerization are considered. Analytical expressions for the exponent n in the power‐law dependence of polymerization rate on initiation rate are derived for these two situations. Theory predicts that n should be below the classical value of 1/2. In the case of non‐ideal initiator decomposition, n decreases with the size of the dimensionless parameter α ≡ (k_tz /k_dz) √r_ink_t, where k_tz is the termination rate coefficient for the reaction of a non‐propagating primary radical with a macroradical, k_dz is the first‐order decomposition rate coefficient of non‐propagating (passive) radicals, r_in is initiation rate, and k_t is the termination rate coefficient of two active radicals. In the case of primary radical termination, n decreases with the size of the dimensionless parameter β ≡ k_t,s r_in^1/2/k_p,s M r_t,l^1/2, where k_t,s is the termination rate coefficients for the reaction of a primary (“short”) radical with a macroradical, k_t,l is the termination rate coefficients of two large radicals, k_p,s is the propagation rate coefficient of primary radicals and M is monomer concentration. As k_t is deduced from coupled parameters such as k_t /k_p, the dependence of k_p on chain length is also briefly discussed. This dependence is particularly pronounced at small chain lengths. Moreover, effects of chain transfer to monomer on n are discussed.     

AGET ATRP of water‐soluble PEGMA: Fast living radical polymerization mediated by iron catalyst

In this work, living radical polymerizations of a water‐soluble monomer poly(ethylene glycol) monomethyl ether methacylate (PEGMA) in bulk with low‐toxic iron catalyst system, including iron chloride hexahydrate and triphenylphosphine, were carried out successfully. Effect of reaction temperature and catalyst concentration on the polymerization of PEGMA was investigated. The polymerization kinetics showed the features of “living”/controlled radical polymerization. For example, M_n,GPC values of the resultant polymers increased linearly with monomer conversion. A faster polymerization of PEGMA could be obtained in the presence of a reducing agent Fe(0) wire or ascorbic acid. In the case of Fe(0) wire as the reducing agent, a monomer conversion of 80% was obtained in 80 min of reaction time at 90 °C, yielding a water‐soluble poly(PEGMA) with M_n = 65,500 g mol^?1 and M_w/M_n = 1.39. The features of “living”/controlled radical polymerization of PEGMA were verified by analysis of chain‐end and chain‐extension experiments. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermal and optical properties of highly fluorinated copolymers of methacrylates

Copolymers of pentafluorophenylhexafluoroisopropyl methacrylate (FPPMA) with trifluoroethyl methacrylate (TFEMA) were prepared in THF solution and in bulk using azobisisobutyronitrile as a free radical initiator. The monomer reactivity ratios of TFEMA (M₁) and FPPMA (M₂) were calculated as r₁ = 0.55 and r₂ = 0.07. The refractive indices of poly(TFEMA) and poly(FPPMA) are very similar as 1.435 and 1.430, respectively, at 532 nm, and the copolymer films were transparent. The glass transition temperatures (T_g) of the copolymers were in the range of 80–90°C and showed a negative deviation from the Gordon–Taylor equation. The thermal decomposition temperature (T_d) was increased with the content of FPPMA in copolymers. Low water absorption for 1:1 FPPMA/TFEMA copolymer was detected. Copolymers of FPPMA with hexafluoroisopropyl methacrylate (HFPMA) were also prepared. The monomer reactivity ratios of HFPMA (M₁) and FPPMA (M₂) were calculated as r₁ = 0.43 and r₂ = 0.10. The T_gs of the copolymers were in the range of 88–95°C and showed also a negative deviation from the Gordon–Taylor equation. T_g and T_d of the copolymers were increased with the content of FPPMA. The refractive index of poly(HFPMA) (1.384 at 532 nm) is much lower than that of FPPMA homopolymer, but copolymer films obtained were clear and transparent. Copyright © 2013 John Wiley & Sons, Ltd.     

Perfluorocyclobutyl-containing Amphiphilic Block Copolymers Synthesized by RAFT Polymerization

Amphiphilic block copolymers containing hydrophobic perfluorocyclobutyl‐based (PFCB) polyacrylate and hydrophilic poly(ethylene glycol) (PEG) segments were prepared via reversible addition‐fragmentation chain transfer (RAFT) polymerization. The PFCB‐containing acrylate monomer, p‐(2‐(p‐tolyloxy)perfluorocyclobutoxy)‐phenyl acrylate, was first synthesized from commercially available compounds in good yields, and this kind of acrylate monomer can be homopolymerized by free radical polymerization or RAFT polymerization. Kinetic study showed the 2,2′‐azobis(isobutyronitrile) (AIBN) initiated and cumyl dithiobenzoate (CDB) mediated RAFT polymerization was in a living fashion, as suggested by the fact that the number‐average molecular weights (M_n) increased linearly with the conversions of the monomer, while the polydispersity indices kept less than 1.10. The block polymers with narrow molecular weight distributions (M_w/M_n≦1.21) were prepared through RAFT polymerization using PEG monomethyl ether capped with 4‐cyanopentanoic acid dithiobenzoate end group as the macro chain transfer agent (mPEG‐CTA). The length of the hydrophobic segment can be tuned by the feed ratio of the PFCB‐based acrylate monomer and the extending of the polymerization time. The micellization behavior of the block copolymers in aqueous media was investigated by the fluorescence probe technique.     

Living cationic polymerization of 2‐adamantyl vinyl ether

Living cationic polymerization of 2‐adamantyl vinyl ether (2‐vinyloxytricyclo[3.3.1.1]^3,7decane; 2‐AdVE) was achieved with the CH₃CH(OiBu)OCOCH₃/ethylaluminum sesquichloride/ethyl acetate [CH₃CH(OiBu)OCOCH₃/Et_1.5AlCl_1.5/CH₃COOEt] initiating system in toluene at 0 °C. The number‐average molecular weights (M_n's) of the obtained poly(2‐AdVE)s increased in direct proportion to monomer conversion and produced the polymers with narrow molecular weight distributions (MWDs) (M_w/M_n = ～1.1). When a second monomer feed was added to the almost polymerized reaction mixture, the added monomer was completely consumed and the M_n's of the polymers showed a direct increase against conversion of the added monomer. Block and statistical copolymerization of 2‐AdVE with n‐butyl vinyl ether (CH₂?CH? O? CH₂ CH₂CH₂CH₃; NBVE) were possible via living process based on the same initiating system to give the corresponding copolymers with narrow MWDs. Grass transition temperature (T_g) and thermal decomposition temperature (T_d) of the poly(2‐AdVE) (e.g., M_n = 22,000, M_w/M_n = 1.17) were 178 and 323 °C, respectively. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1629–1637, 2008     

三嵌段共聚物PS-PHB-PS的原子转移自由基聚合

为了克服聚β-羟基丁酸酯(PHB)的弱点, 得到性能良好的新材料, 本文利用原子转移自由基聚合方法, 以Br-PHB-Br为大分子引发剂, 苯乙烯为单体, 在CuBr/N,N,N′,N″,N″-五甲基–二乙基三胺(PMDETA)催化体系作用下合成了一种新的三嵌段共聚物聚苯乙烯-聚β-羟基丁酸酯-聚苯乙烯(PS-PHB-PS). 共聚物的链结构利用¹H NMR和¹³C NMR进行了表征, 分子量特性和链段组成利用凝胶渗透色谱(SEC)方法进行了测定. 聚合物的分子量随单体转化率的增加而线性增加, 分子量分布指数相对较窄. 这些特征都满足原子转移自由基活性聚合的理想要求. 所得到的共聚物PS-PHB-PS具有较好的生物相容性, 与PHB相比具有良好的耐热性.     

Copolymers from Castor Oil Prepolymers (COP). 4. Copolymerization of Methyl Methacrylate with COP

The copolymerization of castor oil prepolymer (COP) with methyl methacrylate (MMA) has been accomplished at 75°C using a free radical initiator. The monomer reactivity ratios of MMA (r₁) and COP (r₂) were determined to be r₁ = 3.04 and r₂ = 0.605. With an increasing concentration of COP in the binary mixture, copolymers with decreasing molecular weight were obtained. The copolymers obtained were powdery substances soluble in many organic solvents.