四氢萘在Mo-Ni/USY双功能催化剂上加氢裂化反应动力学的研究

在活性趋于稳定的Mo-Ni／USY双功能催化剂上，利用连续流动微反－色谱装置，进行了四氢萘加氢裂化反应动力学的研究，在320－400℃、4．5－8．5MPa反应条件下，考察其反应产物分布，建立了四氢萘加氢裂化反应动力模型，计算了反应网络中各步的反应速率常数和活化能，并讨论了反应网络的主线和反应条件对主线的影响。结果表明，Mo-Ni／USY双功能催化剂具有较高的裂化和异构化活性，低温、高压有利于加氢、高温、低压有利于裂化和异构。     

供氢剂与分散型催化剂协同作用的研究

以辽河渣油为原料,四氢萘为供氢剂,二烷基二硫代氨基甲酸钼为油溶性催化剂在高压釜中进行裂化反应,比较了临氢裂化,临氢供氢裂化,催化加氢裂化以及供氢剂与分散型催化剂共同存在下的加氢裂化,在同样生焦量的情况下,渣油裂化转化率的顺序为：临氢催化供氢过程＞临氢催化过程＞临氢供氢过程＞临氢过程,同时发现供氢剂与分散型催化剂在渣油加氢裂化过程中具有协同作用,与单独使用分散型催化剂的改质反应相比,供氢剂的协同作用不但可以在低转化率下延迟生焦诱导期,提高渣油生焦前的最大转化率,而且在高转化率下对渣油的缩合反应有更大的抑制作用。由420－440℃四集总表观动力学模型计算出的动力学速率常数和活化能表明,供氢剂与分散型催化剂产生的协同作用提高了沥青质和焦生成的活化能,极大地抑制了沥青质和焦生成 速率,而对可溶质生成馏分油的裂化反应的抑制作用很小。     

稳定同位素方法研究模型化合物之间的氢转移反应

二十烷,菲作为模型化合物,以四氢萘为供氢剂,在临氮及临氢体系中应用氘代四氢萘考察供氢剂的氢转移反应,发现供氢剂抑制烷烃的裂化,其作用是通过脱氢湮灭自由基来抑制裂化反应。临氮及临氢条件下,与正二十烷与菲的二元体系相比,正二十烷,菲和四氢萘三元体系中四氢萘不仅能生成较多的菲的氢化芳烃产物,而且稳定同位素方法表明氘代四氢萘可以向菲和菲的氢化芳烃产物转移更多的氘,同时发现H12－四氢萘和D12－四氢萘的供氢（氘）率上存在着动力学同位素效应。     

HY／MCM-41／γ-A12O3负载的硫化态Ni-Mo-P催化剂上萘的加氢

采用水热法合成了不同SiO2／Al2O3比的MCM-41介孔分子筛．并分别以HY／MCM-41／γ-A1203，HY／γ-A12O3和γ-Al2O3为载体，用浸渍法制备了Mo-Ni-P催化剂．以萘为模型化合物，考察了硫化态Mo-Ni-P催化剂的加氢活性．结果表明，不同载体负载的催化剂催化活性均随着活性组分负载量的增大而提高，其中掺杂大比表面MCM-41的HY／MCM-41/γ-Al2O3所负载的催化剂催化活性提高幅度最大．由于MCM-41与HY分子筛在酸性和孔结构上存在互补性，因而催化剂对萘加氢存在协同作用．提出了萘加氢的反应机理，认为反应网络包括两个平行路径：-是萘加氢生成四氢萘后发生异构化或开环反应；二是萘加氢生成四氢萘后进-步加氢生成十氢萘，继而发生异构化或开环反应．     

HY/MCM-41/γ-Al2O3负载的硫化态Ni-Mo-P催化剂上萘的加氢

 采用水热法合成了不同SiO2/Al2O3比的MCM-41介孔分子筛. 并分别以HY/MCM-41/γ-Al2O3, HY/γ-Al2O3和γ-Al2O3为载体,用浸渍法制备了Mo-Ni-P催化剂. 以萘为模型化合物,考察了硫化态Mo-Ni-P催化剂的加氢活性. 结果表明,不同载体负载的催化剂催化活性均随着活性组分负载量的增大而提高,其中掺杂大比表面MCM-41的HY/MCM-41/γ-Al2O3所负载的催化剂催化活性提高幅度最大. 由于MCM-41与HY分子筛在酸性和孔结构上存在互补性,因而催化剂对萘加氢存在协同作用. 提出了萘加氢的反应机理,认为反应网络包括两个平行路径: 一是萘加氢生成四氢萘后发生异构化或开环反应; 二是萘加氢生成四氢萘后进一步加氢生成十氢萘,继而发生异构化或开环反应.     

稳定同位素方法研究正构烷烃与四氢萘二元体系的反应

以正构烷烃作为模型化合物的热反应、临氢反应、临氢催化反应中,添加供氢剂抑制正构烷烃所裂化;气相氢和供氢剂的供氢参与饱和烯烃,两者是性质不同的氢源,前者加速裂化,后者抑制裂化。供氢剂供氢行为依赖于反应体系自由基的多少和温度以及反应过程,反应体系较多的自由基和较高的反应温度有利于供氢行为。稳定同位素方法研究模型化合物的裂化反应表明,供氢剂的作用是通过脱氢湮灭自由基来抑制裂化反应,同时发现H12－四氢萘和D12－四氢萘的供氢（氘）率上存在着动力学同位素效应,在临氢及临氢催化体系中尤其是临氢催化体系中,动力学同位素效应变得不再明显。     

MCM-41负载钴催化H_2O_2氧化四氢萘合成α-四氢萘酮

比较了醋酸溶液中过渡金属(Fe、Co、Ni、Ce、Cu、La、Zr或Cr)掺杂MCM-41催化过氧化氢氧化四氢萘合成α-四氢萘酮的转化率和选择性,发现其中Co/MCM-41的催化活性最好。探讨了Co/MCM-41作催化剂时反应温度、反应时间、催化剂用量等对四氢萘氧化的转化率和形成四氢萘酮选择性的影响,确定了较优的反应条件:m(四氢萘)∶m(催化剂)=12.5∶1;反应温度T=383 K,反应时间8 h。四氢萘的转化率达94.7%,α-四氢萘酮的选择性达到70.3%。在反应体系中,Co/MCM-41是一种固体非均相催化剂。催化剂Co/MCM-41可回收重复使用3次,催化活性基本不变。     

正癸烷加氢裂化集总动力学研究

选用国产３８２５加氢裂化催化剂，对正癸烷加氢裂化动力学进行了研究。根据Ｗｅｅｋ－ｍａｎ集总原理，建立了正癸烷加氢裂化四集总动力学模型。利用Ｍａｒｑｕａｒｄｔ法估计了各反应速度常数，确定了完善的速度表达式。计算了两种压力（６．５和８．５ＭＰａ）下的表观活化能，预测了各反应产物分布，其计算结果与实验值吻合。同时，讨论了空速、温度、压力和反应活化能对产物分布的影响，为重油和渣油加氢裂化集总动力学研究提供     

贵金属铂对镍基催化剂上萘转化性能的影响

 在常压连续流动固定床反应器上，以萘作为生物质气化气中焦油的模型化合物，研究了Pt对Ni／Al2O3催化剂上萘的转化率、CO和H2的选择性及收率的影响，比较了Ni－Pt／Al2O3和Ni／Al2O3两种催化剂上萘的水蒸气转化所产生的积碳量和副产物的种类，并初步考察了Ni－Pt／Al2O3催化剂上萘的水蒸气转化反应的动力学．     

Co/Al_2O_3催化褐煤衍生模型化合物的加氢脱氧制单体烃类化合物

以钴铝类水滑石(CoAl-LDH)为前驱体,经焙烧和氢气还原制备了Co/Al_2O_3催化剂。采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线光电子能谱(XPS)等表征手段研究了前驱体及催化剂的理化性质。以2-萘基醚为褐煤模型化合物,考察了Co/Al_2O_3催化其加氢脱氧制单体烃的性能。结果表明,Co/Al_2O_3-700催化剂具有最高的加氢脱氧活性,在温度250℃和氢气压力2 MPa反应条件下,反应90 min时2-萘基醚完全转化为单体烃(十氢化萘和四氢化萘)。2-萘基醚先加氢生成6,6′-氧代二(1,2,3,4-四氢萘),然后断裂C-O键生成四氢化萘和5,6,7,8-四氢-2-萘酚是主要反应路径。此外,Co/Al_2O_3-700对褐煤衍生苄醚和苯醚模型化合物加氢脱氧同样具有很高的催化活性。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.