碱性离子液体催化甘油合成1,2-甘油碳酸酯(英)

以离子液体为催化剂,在无溶剂体系中,考察了生物质平台化合物甘油转化1,2-甘油碳酸酯的反应.与酸性离子液体和常用无机碱性催化剂相比,碱性离子液体咪唑基1-丁基-3-甲基咪唑([Bmim]Im)、氢氧化1-丁基-3-甲基咪唑([Bmim]OH)、咪唑基1-烯丙基-3-甲基咪唑([Amim]Im)、氢氧化1-烯丙基-3-甲基咪唑([Amim]OH)在甘油与碳酸二甲酯的酯交换反应中表现出优异的活性.其中,以[Bmim]Im离子液体为催化剂时甘油转化率为98.4%和甘油碳酸酯选择性接近100%.另外,该离子液体可以回收重复利用3次后甘油转化率仍可达92%,甘油碳酸酯选择性可近100%.此碱性离子液体催化方法具有反应结果较好、产物分离简单、条件温和以及环境友好等特点.     

壳聚糖在4种咪唑型离子液体中溶解性的研究

研究、比较了壳聚糖在4种咪唑型离子液体氯化1-丁基-3-甲基咪唑([BMIM]Cl)、1-丁基-3-甲基咪唑醋酸盐([ BMIM] Ac)、1-乙基-3-甲基咪唑醋酸盐([EMIM] Ac)和氯化1-烯丙基-3-甲基咪唑([AMIM] Cl)中的溶解性,提出了可能的溶解机理,并利用红外光谱(FTIR)、热重分析(TGA...     

L-脯氨酸稳定的铱催化苯乙酮及其衍生物不对称加氢反应

以L-脯氨酸为稳定剂制备了负载型金属铱催化剂, 并用于苯乙酮及其衍生物不对称加氢反应. 考察了载体以及L-脯氨酸的量对催化剂性能的影响, 以透射电镜(TEM)和X射线光电子能谱(XPS)对催化剂进行了表征. 结果表明L-脯氨酸对金属铱粒子具有较好的分散和稳定作用. 通过考察反应条件发现: 碱金属离子对反应有较大影响; L-脯氨酸与手性修饰剂对催化活性和对映选择性存在一定的协同促进作用. 在手性二胺(1S,2S)-1,2- 二苯基乙二胺 ((1S,2S)-DPEN) 修饰下, 催化剂 5% (w, 质量分数)Ir/15( 脯氨酸与铱的摩尔比)(L-Proline)-γ-Al2O3催化苯乙酮不对称加氢获得了71.3%的对映选择性(ee), 2?-(三氟甲基)苯乙醇的对映选择性达到了79.8%. 该催化剂制备方法简单, 不需要膦配体做稳定剂, 催化剂性能稳定, 通过简单的离心分离可循环使用5次而无明显的活性和对映选择性降低.     

水/有机两相体系中钌膦配合物催化苯乙酮及其衍生物的不对称加氢反应

 将手性二胺(1S,2S)-1,2-二苯基乙二胺二磺酸钠((1S,2S)-DPENDS)修饰的钌膦配合物用于催化水/有机两相体系中苯乙酮的不对称加氢. 结果表明, (1S,2S)-DPENDS和KOH的浓度对反应有很大影响,二者的协同作用使配合物的催化活性和产物的对映选择性大大提高. 对温度、压力、底物/钌的摩尔比和膦配体/钌摩尔比等反应条件进行优化后,以［RuCl2-(TPPTS)2］2为催化剂前体催化苯乙酮不对称加氢时,产物的ee值可达66.4%, 催化剂经过简单的相分离即可循环使用.     

聚乙二醇-水介质中水溶性膦稳定的钌催化芳香酮的不对称加氢反应

在聚乙二醇-400-水介质中,以(1S,2S)-1,2-二苯基乙二胺的磺酸钠盐为手性修饰剂,考察了水溶性三(间-磺酸钠苯基)膦稳定的Ru催化苯乙酮及其衍生物的不对称加氢反应.结果表明,该催化剂体系具有良好的催化活性和对映选择性.在优化反应条件下,苯乙酮转化率和对映选择性分别为100％和84.9％.经正己烷萃取后,催化剂...     

聚乙二醇400-水介质中水溶性钌膦二胺催化苄叉丙酮的不对称加氢反应

在聚乙二醇400-水绿色可循环介质中,以手性二胺(S,S)-1,2-二苯基乙二胺二磺酸钠((S,S)-DPENDS)与非手性钌膦络合物([RuCl2(TPPTS)2]2)原位生成的水溶性钌膦二胺为催化剂,考察了苄叉丙酮的选择性不对称加氢反应.在优化的反应条件下,羰基加氢产物4-苯基-3-丁烯-2-醇的化学选择性和对映选择性分别为98.5%和74.3%.经正己烷萃取后,催化剂即可从产物中分离出来.循环使用5次后,4-苯基-3-丁烯-2-醇化学选择性和对映选择性没有明显下降.     

咪唑根碱性离子液体在水介质Knoevenagel反应中的催化作用

报道了咪唑根1-丁基-3-甲基咪唑([Bmim]Im)碱性离子液体的合成与表征,该离子液体具有强碱性和较好的热稳定性.碱性离子液体[Bmim]Im用于催化水介质中Knoevenagel反应,发挥了碱催化剂与相转移催化剂双重作用.此外,离子液体[Bmim]Im及其水溶液还具有良好的循环使用性能.水介质、低催化剂用量、室温...     

L-脯氨酸修饰的铱催化苯乙酮及其衍生物不对称加氢反应

在温和条件下制备了L-脯氨酸稳定并修饰的负载型金属铱催化剂,用于苯乙酮及其衍生物不对称催化加氢反应. 考察了L-脯氨酸的量、溶剂、碱以及碱的量和氢气压力对苯乙酮不对称催化加氢反应的影响. 结果显示,该催化剂催化苯乙酮不对称加氢反应获得了92.1%的转化率和32.9%的对映选择性(e.e.),催化2′-(三氟甲基)苯乙醇的对映选择性为39.3,这一结果高于目前报道的天然手性修饰剂修饰的负载型金属催化剂. 该催化循环使用5次, 对映选择性只有小幅度下降.     

膦功能化离子液稳定的纳米钯催化喹啉高选择性加氢

通过简单的还原方法在离子液体[BMMIM]PF_6(1-丁基-2,3-二甲基咪唑六氟磷酸盐)中,以膦功能化离子液体[BMMIM][tppm](1-丁基-2,3-二甲基咪唑间三苯基膦单磺酸盐)为稳定剂制备了纳米钯催化剂。采用透射电镜(TEM)、X-射线衍射(XRD)、X-射线光电子能谱(XPS)等方法对纳米钯催化剂进行了表征。结果表明:[BMMIM][tppm]稳定的纳米钯催化剂分散均匀,平均粒径约为3.9 nm,且Pd(Ⅱ)完全转化为Pd(0)。在喹啉加氢反应过程中,考察了稳定剂种类、稳定剂用量、溶剂、温度、压力等因素对喹啉选择性加氢的影响。在50℃和氢气压力为3.5MPa的温和条件下,纳米钯催化剂催化喹啉及其衍生物加氢显示出高活性和高化学选择性。在循环过程中,膦功能化离子液体稳定的纳米钯催化剂能保持良好的催化活性和化学选择性。     

水相中RuCl2(TPPTS)2-(S,S)-DPENDS催化苄叉丙酮的不对称加氢反应

 将水溶性手性二胺 (S,S)-1,2-二苯基乙二胺二磺酸钠 ((S,S)-DPENDS) 与钌膦配合物 ([RuCl2(TPPTS)2]2) 原位生成的催化剂用于催化水相中苄叉丙酮的不对称加氢反应. 在优化条件下, 羰基加氢产物 4-苯基-3-丁烯-2-醇的选择性可达 96.0%, 对映选择性可达 71.2%. 经正己烷简单萃取后即可实现催化剂与加氢产物的分离, 循环使用 5 次后, 目标产物 4-苯基-3-丁烯-2-醇选择性和对映选择性没有明显下降.     

Surface tension of binary mixtures of imidazolium and ammonium based ionic liquids with alcohols, or water: cation, anion effect

The surface tensions were measured at atmospheric pressure, with use of a ring tensiometer, of a series of alcoholic solutions of closely related ionic liquids: 1-methyl-3-methylimidazolium methylsulfate, [MMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium methylsulfate, [BMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium octylsulfate, [BMIM][OcSO4] in alcohol (methanol, or 1-butanol at 298.15 K) and of 1-hexyloxymethyl-3-methylimidazolium tetrafluoroborate, [C6H(13)OCH2MIM][BF4], 1,3-dihexyloxymethylimidazolium tetrafluoroborate, [(C6H13OCH2)2IM][BF4] in alcohol (methanol, or 1-butanol, or 1-hexanol at 308.15 and 318.5 K) and hexyl(2-hydroxyethyl)dimethylammonium bromide, C6Br in 1-octanol at 298.15 K. The set of ammonium ionic liquids of different cations and anions (C2Br, C2BF4, C2PF6, C2N(CN)2, C3Br, C4Br and C6Br) was chosen to show the influence of small amount of the ammonium ionic liquid on the surface tension of water at 298.15 K. The influence of the cation, or anion alkyl chain length on the properties under study (densities and surface tension) was tested.     

Photophysics and dynamics of a β-carboline analogue in room temperature ionic liquids

Room temperature ionic liquids are rapidly emerging as a new class of media that are ideally suited for various applications including carrying out chemical reactions. In the present article, we report the photophysics of a β-carboline analogue, namely, 3-acetyl-4-oxo-6,7-dihydro-12H indolo-[2,3-a] quinolizine (AODIQ), in three room temperature ionic liquids (RTILs), 1-butyl-3-methylimidazolium methyl sulfate ([BMIM][MeSO(4)]), 1-butyl-3-methylimidazolium octyl sulfate ([BMIM][C(8)SO(4)]) and 1-ethyl-3-methylimidazolium methyl sulfate ([EMIM][MeSO(4)]). Out of these, [BMIM][C(8)SO(4)] is a typical RTIL that forms micellar aggregates above a critical micellar concentration (CMC). Steady state absorption, steady state and time resolved fluorescence techniques are used to probe the properties of these systems. The investigation reveals that the photophysics of AODIQ is modified significantly in the micelle-forming RTIL as compared to that in the other two. A comparative study with the fluorophore in [BMIM][C(8)SO(4)] and a conventional anionic surfactant of a similar hydrophobic chain length from the sodium-n-alkyl sulfate series, viz., sodium octyl sulfate (S(8)S), reveals that the fluorophore experiences a more constrained environment in the RTIL micelle as compared to the conventional anionic micelle.     

Growth of sputter-deposited gold nanoparticles in ionic liquids

The growth of gold nanoparticles (NPs) synthesized by sputter deposition on an ionic liquid surface is studied in situ in the bulk phase of the ionic liquids (ILs) 1-butyl-3-methylimidazolium dicyanamide [C(1)C(4)Im][N(CN)(2)], 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)amide [C(1)C(4)Im][Tf(2)N], 1-butyl-3-methylimidazolium tetrafluoroborate [C(1)C(4)Im][BF(4)], 1-butyl-3-methylimidazolium hexafluorophosphate [C(1)C(4)Im][PF(6)] and 1-butyl-3-methylimidazolium triflate [C(1)C(4)Im][TfO]. It is found that primary nanoparticles with a diameter smaller than 2.5 nm are present in the sample immediately after sputtering. Growth of these primary particles proceeds after the end of the sputtering process and stops when the nanoparticles reach a certain size. Depending on the viscosity of the ionic liquid this growth process can proceed several hours to several days. The growth speed is fastest for the least viscous ionic liquid and follows the trend [C(1)C(4)Im][N(CN)(2)] > [C(1)C(4)Im][Tf(2)N] > [C(1)C(4)Im][TfO] > [C(1)C(4)Im][BF(4)] > [C(1)C(4)Im][PF(6)]. It is also found that a higher concentration of sputtered gold results in faster growth of the gold nanoparticles. A discussion on the growth mechanism of sputtered gold NPs is included.     

High-pressure infrared spectroscopy of ionic liquids mixed with Tween 80

In this study, the possibility of using Tween 80 to disturb the microstructures of 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIM]BF₄) and 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM]PF₆) was investigated under high pressures. The imidazolioum C H absorptions of pure ionic liquids (ILs) are significantly blue-shifted under high pressures. However, mild changes in imidazolioum C H stretching frequencies were observed for IL/Tween 80 mixtures. Tween 80 may hinder cations of ILs to form network structures with anions under high pressures via pressure-enhanced cation-Tween 80 interactions. Based on the experimental results, Tween 80-[BMIM]PF₆ interactions are more effective in disturbing the local structure of imidazolium C H than Tween 80-[BMIM]BF₄ interactions.     

The thermochemistry of solvation of imidazolium-based ionic liquids in benzene

ABSTRACT

The present work is devoted to the thermochemical study of solvation of ionic liquids (IL) in benzene. The solution enthalpies of 1-ethyl-3-methylimidazolium tricyanomethanide [EMIM][C(CN)₃], 1-butyl-3-methylimidazolium tetrafluoroborate [BMIM][BF₄], 1-hexyl-3-methylimidazolium hexafluorophosphate [HMIM][PF₆], 1-octyl-3-methylimidazolium tetrafluoroborate [OMIM][BF₄], 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [EMIM][NTf₂], 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide [BMIM][NTf₂] and 1-butyl-3-methylimidazolium trifluoromethanesulfonate [BMIM][TfO] in benzene were measured. The solvation enthalpies of imidazolium-based IL were calculated. Molar refractions of imidazolium-based IL form literature data on density and refractive indexes of IL were also calculated. The linear correlation between solvation enthalpy and molar refraction of IL was observed. This correlation can be used to calculate the vaporization enthalpy of imidazolium-based IL from solution calorimetry data.     

用[BMIM][Cu2Cl3]离子液体萃取脱除汽油中的硫化物

以不同的IL（ionic liquid）/油质量比，采用[BMIM][Cu2Cl3]（[BMIM]=1-butyl-3-methylimidazolium）对模型汽油和商品汽油进行单步和多步萃取脱硫实验；并合成几种具有不同阴离子和阳离子结构的离子液体，评价和比较了离子液体对商品汽油的萃取脱硫性能的影响。实验结果表明，具有较好的水稳定性和常温流动性的[BMIM] [Cu2Cl3]离子液体硫容较高，在IL/油质量比为1∶3时，经多步萃取后，油品中的硫质量分数降至20×10-6～30×10-6，累计脱硫率超过95%。汽油中其他组分对脱硫效果影响很小。[BMIM][Cu2Cl3]与汽油形成稳定的两相系统，分离方便。离子液体脱硫能力可以通过四氯化碳反萃取完全恢复。     

GC–MS study of thermochemical conversion of guaifenesin in the presence of 1-butyl-3-methylimidazolium-based ionic liquids

Research on Chemical Intermediates - Thermochemical conversion of guaifenesin was performed in the presence of 1-butyl-3-methylimidazolium tetrafluoroborate [BMIM][BF4] ionic liquid at...     

A new diastereoselective intramolecular electroreductive coupling of unsaturated β-ketoesters and β-ketoamides in ionic liquids at a tin cathode

The diastereoselective intramolecular electroreductive coupling of several β-ketoesters and β-ketoamides has been accomplished at a tin cathode in ionic liquids and isopropanol (9:1). The ionic liquids used are 1-butyl-3-methylimidazolium bromide [BMIM]Br, 1-butyl-3-methylimidazolium tetrafluoroborate [BMIM]BF₄, 1-methoxyethyl-3-methylimidazolium trifluoroacetate [MOEMIM]CF₃COO and 1-methoxyethyl-3-methylimidazolium mesylate [MOEMIM]Ms. This methodology offers a clean and green process for the synthesis of functionalized carbocycles in good yields with excellent stereochemical control at three stereogenic centres.     

A Bloembergen–Purcell–Pound <Superscript>13</Superscript>C NMR relaxation study of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate

The molecular structure and rotational motion of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM][PF6]) were studied over a wide temperature range using the Bloembergen–Purcell–Pound ¹³C NMR spin–lattice relaxation method and NOE factors. Examination of the spin–lattice relaxation times (T ₁) and the rates (R ₁=1/T ₁) of the 1-butyl-3-methylimidazolium cation reveals the relative motions of each carbon in the imidazolium cation. The rotational characteristics of the [BMIM] cation are supported by ab-initio molecular structures of [BMIM][PF6] using density functional theory (DFT) and Hartree–Fock (HF) methods. The ab-initio gas phase structures of [BMIM][PF6] indicate that the 1-butyl-3-methylimidazolium C2 hydrogen, the ring methyl group, and the butyl side-chain hydrogen atoms form hydrogen bonds with the hexafluorophosphate anion.     

Asymmetric hydrogenation of aromatic ketones catalyzed by achiral monophosphine TPPTS-stabilized Ru in ionic liquids

Achiral monophosphine TPPTS [TPPTS: P(m-C₆H₄SO₃Na)₃]-stabilized Ru was synthesized by reduction of RuCl₃·3H₂O with hydrogen in ethanol using TPPTS as the stabilizer. The catalytic asymmetric hydrogenation of aromatic ketones using TPPTS-stabilized Ru modified by a chiral diamine (1R,2R)-DPENDS [disodium salt of sulfonated (1R,2R)-1,2-diphenyl-1,2-ethylene-diamine] was investigated in hydrophilic ionic liquid [RMIM]Ts (1-alkyl-3-methylimidazolium p-methylphenylsulfonates, R = ethyl, butyl, octyl, dodecyl, hexadecyl). Hundred percent conversion and 85.1% ee were obtained for acetophenone under optimized conditions. The resulting products can be easily separated from the catalyst immobilized in ionic liquid by simple extraction with n-hexane, and the catalyst can be reused several times without a significant loss of ee value or conversion. In particular, the addition of water can improve the catalyst performance.