价电子平均能级连接性指数及其应用

定义价电子平均能级（δi）为：δi=(ni-1)(ni+ΣEij)0.5/(1+mi)。由δi建构分子连接性指数（mQ）,其中,0Q=Σ(δi)-0.5、1Q=Σ(δiδj)-0.5。0Q与无机物总键能ΔE、0Q2与过渡元素卤化物的ΔfHmθ、1Q0.5与碱金属卤化物晶格能U、0Q及1Q与无机氢化物pKa的相关系数分别为0.9734、0.9769、0.9906、0.9945,均优于文献方法。mQ是一种结构选择性、性质相关性俱佳的拓扑指数。     

荧光法研究盐酸多赛平与牛血清白蛋白的相互作用

应用荧光共振能量转移(FRET)技术研究了生理条件下,盐酸多赛平(DH)和牛血清白蛋白(BSA)的相互作用.结果表明DH经非辐射能量转移猝灭BSA的荧光.分析荧光猝灭光谱数据,由Stern-Volmer方程、double-reciprocal方程和热力学公式,求得20℃时该反应的标准焓变、标准熵变、标准吉布斯自由能变分别为-15.16kJ.mol-1,37.20J.mol-1.K-1,-26.06kJ.mol-1.结合反应的结合常数为4.42×104,DH在BSA分子上色氨酸残基所在区域的结合位点数为1.75,其作用距离为3.70nm.并从同步荧光光谱考察了DH对BSA构象的影响.     

La-H化合物对LaMg2Ni合金中Mg2Ni相吸氢过程的影响

采用感应熔炼技术在Ar气氛保护下制备得到LaMg2Ni与Mg2Ni合金。X射线衍射(XRD)图表明LaMg2Ni合金在吸氢过程中分解为LaH3相和Mg2NiH4相,放氢过程中LaH3相转化为La3H7相。与Mg2Ni合金相比,LaMg2Ni合金显示出优良的吸氢动力学性能,这是由于镧氢化合物的存在及其在吸氢过程中所发生的相转变所造成的。LaMg2Ni合金280 s内吸氢即可达到最大储氢量的90%以上,而Mg2Ni合金则需要1200 s才能达到,且在相同温度下LaMg2Ni合金的吸氢反应速率常数大于Mg2Ni合金速率常数。镧氢化合物不仅有利于改善动力学性能,而且可以提高热力学性能。LaMg2Ni合金中的Mg2Ni相氢化反应焓与熵分别为-53.02 kJ.mol-1和84.96 J.K-1.mol-1(H2),这一数值小于单相Mg2Ni氢化反应焓与熵(-64.50 kJ.mol-1,-123.10 J.K-1.mol-1(H2))。压力-组成-温度(P-C-T)测试结果表明在603 K至523 K温度范围内,LaMg2Ni合金储氢容量保持稳定为1.95wt%左右,然而Mg2Ni合金的储氢容量则由4.09wt%衰减为3.13wt%,Mg2Ni合金的储氢容量在523K低温下仅为603 K时的76.5%,表明镧氢化合物能够改善Mg2Ni合金低温下的吸放氢性能。     

氨基膦酸树脂对溶液中锌的吸附研究

研究了Zn2+在氨基膦酸树脂上的吸附行为。结果表明,静态饱和吸附容量为209.2mg.g-1树脂,用2.0 mol.L-1的HCl溶液洗脱,洗脱率为98%以上;测得吸附热力学参数分别为:ΔH=8.14 kJ.mol-1,ΔG=-3.06 kJ.mol-1,ΔS=37.6 J.mol-1.K-1。等温吸附服从Freundlich吸附等温式;表观活化能Ea=14.7 kJ.mol-1,表观速率常数k298=4.26×10-5s-1;树脂功能基与Zn2+的配位比约为1∶1;并用化学和红外光谱的方法探讨了树脂对Zn2+的吸附机理。     

高效液相色谱法测定金属配合物｛Fe［3-(2-吡啶基)-5,6-二苯基-1,2,4-三嗪］3｝2+两种几何异构体的动力学转变

通过高效液相色谱法研究了3-(2-吡啶基)-5,6-二苯基-1,2,4-三嗪(PDT)和Fe(Ⅱ)的配合物［Fe(PDT)3］2+的面式和经式两种几何异构体之间的动力学平衡过程。结果表明:不同温度(30,35,40,45 ℃)下,两种几何异构体含量(x)之间的相互转变均符合动力学一级反应,其xeln［(xe-x0)/(xe-x)］值和反应时间t(min)之间的关系分别为:xeln［(xe-x0)/(xe-x)］=0.082t+0.729 (r2=0.9911,T=45 ℃),xeln［(xe-x0)/(xe-x)］=0.049t+0.598 (r2=0.9987,T=40 ℃),xeln［(xe-x0)/(xe-x)］=0.022t+0.586 (r2=0.9987,T=35 ℃),xeln［(xe-x0)/(xe-x)］=0.012t+0.591(r2=0.9988,T=30 ℃)。两种异构体之间的动力学相互转变过程中的活化焓(ΔH)、活化熵(ΔS)和活化能(ΔEa)分别为:ΔH=103.84 kJ·mol-1,ΔS=271.93 J·mol-1·K-1,ΔEa=86.74 kJ·mol-1 (面式异构体向经式异构体转变);ΔH=106.47 kJ·mol-1,ΔS=257.65 J·mol-1·K-1,ΔEa=94.43 kJ·mol-1 (经式异构体向面式异构体转变)。     

复合金属氧化物SrCoO3-δ氧非化学计量研究

通过NH4NO3共熔法合成了SrCoO3-δ,利用XRD和差热分析对其进行了结构表征,采用精密气体测量方法研究了SrCoO-在温度672-918K区间,氧气分压0.7-59.3kPa区间内氧的非化学计量及其与外界氧分压、温度的定量关系,在提出氧缺陷形成模型的基础之上,首次给出了描写SrCoO3-δ-O2体系相平衡的数学公式.并以SrFeO3-δ为例评价了该缺陷模型的普适性.测定了SrCoO3-δ-O2体系溶氧过程的焓变和熵变分别为(75.3±1.2)kJ·mol-1,(96.7±1.5)J·mol-1·K-1     

用配分函数预测固体化合物中阳离子标准熵

根据独立共同可别粒子体系的熵与配分函数的关系,建立了70种固体化合物中阳离子标准熵(Sθm,J·mol-1·K-1)与其相对原子质量(Ar,i)、基态原子的简并度(geo,j)的数学模型为:Sθm=-0.25+6.22(lnAr,i)1.4-0.02(lngeo,i)2,R=0.9995。其计算值与实验值非常吻合。     

多元电解质溶液表面张力的新型预测方程

将半理想溶液理论和Butler方程相结合建立了预测多元电解质溶液表面张力的新型线性预测方程.新方程可由二元系数据预测多元系的表面张力数据,而不涉及任何多元交互作用参数.利用不同温度下24个混合电解质溶液的表面张力数据对新方程进行了系统检验.结果表明新方程可利用298.15K时二元系的渗透压系数和不同温度下二元系的表面张力数据预测不同温度下高浓度的多元系的表面张力数据,且预测结果与实验数据符合得很好,并且预测结果普遍优于基于Pitzer方程的表面张力模型.     

La-Fe基NaZn13型化合物的磁场诱导熵变研究

围绕具有一级磁性相变的La-Fe基NaZn13型化合物的磁场诱导熵变研究,从室温磁制冷目的出发讨论了材料研究和熵变机制。La-Fe-Si在190K附近5T磁场下的熵变值可达29J.kg-1.K-1。用少量Co替代Fe,可以获得室温附近5T磁场下熵变为15J.kg-1.K-1的大熵变材料。这类材料中的熵变主要由磁有序熵变和晶格熵变组成。分析了一级磁性相变体系中磁有序熵变和晶格熵变对总熵变的贡献,并发现大的熵变来源于被晶格贡献抵消后的磁有序熵变。     

溴百里酚蓝与牛血清白蛋白的相互作用研究

在模拟动物体生理条件和不同温度下,用荧光光谱和紫外-可见吸收光谱法研究了溴百里酚蓝(BTB)与牛血清白蛋白(BSA)结合反应的光谱行为。用Stern-Volmer和Lineweaver-Burk方程分别处理试验数据,发现BSA与BTB发生反应生成了新的复合物,属于静态荧光猝灭。求出了反应时复合物的形成常数KLB(2.792×105L.mol-1)、热力学参数(ΔHθ=(20.24 kJ.mol-1,ΔSθ=37.22J.K-1,ΔGθ=(31.25kJ.mol-1)与结合位点数(1.1578)。根据F rster偶极-偶极非辐射能量转移理论计算出结合位置距离212位色氨酸残基2.60nm,证明二者主要靠静电作用力结合。同时用同步荧光光谱和三维荧光光谱法探讨了BTB对BSA构象的影响,表明BTB使色氨酸残基所处微环境的极性减弱、疏水作用增强,为阐明BTB的染色机理、毒理效应和生物学效应提供重要信息。     

原子配分参数、配分连接性指数及其应用

结构决定性质，性质反映结构，这是化学、生物学等学科的一条基本规律。因此，分子的微观结构与性质之间存在着密切关系。物质的理化性质、生物活性等数据的获取，迄今主要来自于实验。如能建立结构与性能之间的数量关系用以估算与预测分子的性质，这无疑是一项十分有意义的工作。拓扑指数法以其计算简单、准确性高、应用范围广而在上述领域中发挥重要作用犤１～４犦。拓扑指数是对分子结构进行的定量描述，使分子之间的结构差异定量化。自Wiener提出第一个拓扑指数（W）犤５犦以来，迄今已有２００余种拓扑指数问世。其中一部分能够有效地…     

Quantitative Structure Property Relations （QSPR） for Predicting Molar Diamagnetic Susceptibilities,xm, of Inorganic Compounds

For predicting the molar diamagnetic susceptibilities of inorganic compounds, a novel connectivity index ^mG based on adjacency matrix of molecular graphs and ionic parameter gi was proposed. The gi is defined as gi=（ni^0.5-0.91）^4·xi^0.5｜Zi^0.5, where Zi, ni, xi are the valence, the outer electronic shell primary quantum number, and the electronegativity of atom i respectively. The good QSPR models for the molar diamagnetic susceptibilities can be constructed from ^0G and ^1G by using multivariate linear regression （MLR） method and artificial neural network （NN） method. The correlation coefficient r, standard error, and average absolute deviation of the MLR model and NN model are 0.9868, 5.47 cgs, 4.33 cgs, 0.9885, 5.09 cgs and 4.06 cgs, respectively, for the 144 inorganic compounds. The cross-validation by using the leave-one-out method demonstrates that the MLR model is highly reliable from the point of view of statistics. The average absolute deviations of predicted values of the molar diamagnetic susceptibility of other 62 inorganic compounds （test set） are 4.72 cgs and 4.06 cgs for the MLR model and NN model. The results show that the current method is more effective than literature methods for estimating the molar diamagnetic susceptibility of an inorganic compound. Both MLR and NN methods can provide acceptable models for the prediction of the molar diamagnetic susceptibilities. The NN model for the molar diamagnetic susceptibilities appears more reliable than the MLR model.     

4-硝基苯甲醇的低温热容和标准摩尔生成焓

用精密自动绝热量热计测定了4-硝基苯甲醇（4-NBA）在78 ~ 396 K温区的摩尔热容。其熔化温度、摩尔熔化焓及摩尔熔化熵分别为:(336.426 ± 0.088) K, (20.97 ± 0.13) kJ×mol-1 和 (57.24 ± 0.36) J×K-1×mol-1.根据热力学函数关系式,从热容值计算出了该物质在80 ~ 400 K温区的热力学函数值 [HT - H298.15 K] 和[ST - S298.15 K]. 用精密氧弹燃烧量热计测定了该物质在T＝298.15 K的恒容燃烧能和标准摩尔燃烧焓分别为 (C7H7NO3, s)＝- ( 3549.11 ± 1.47 ) kJ×mol-1 和 (C7H7NO3, s)＝- ( 3548.49 ± 1.47 ) kJ×mol-1. 利用标准摩尔燃烧焓和其他辅助热力学数据通过盖斯热化学循环, 计算出了该物质标准摩尔生成焓 (C7H7NO3, s)＝- (206.49 ± 2.52) kJ×mol-1 .     

2-氯-N,N-二甲基尼古丁酰胺的热容和热力学性质研究

Low-temperature heat capacities of 2-chloro-N,N-dimethylnicotinamide were precisely measured with a high-precision automated adiabatic calorimeter over the temperature range from 82 K to 380 K. The compound was observed to melt at （342.15±0.04） K. The molar enthalpy AfusionHm, and entropy of fusion, △fusionSm, as well as the chemical purity of the compound were determined to be （21387±7） J·mol^-1, （62.51±0.01） J·mol^-1·K^-1, （0.9946±0.0005） mass fraction, respectively. The extrapolated melting temperature for the pure compound obtained from fractional melting experiments was （342.25±0.024） K. The thermodynamic function data relative to the reference temperature 298.15 K were calculated based on the heat capacity measurements in the temperature range from 82 to 325 K. The thermal behavior of the compound was also investigated by different scanning calorimetry.     

Thermal Behavior of N,N＇Bis[N-（2,2,2-trinitroethyl）-N-nitro]ethylenediamine

The thermal behavior and kinetic parameters of the exothermic decomposition reaction of N‐N‐bis[N‐(2,2,2‐tri‐nitroethyl)‐N‐nitro]ethylenediamine in a temperature‐programmed mode have been investigated by means of differential scanning calorimetry (DSC). The results show that kinetic model function in differential form, apparent activation energy E_a and pre‐exponential factor A of this reaction are 3(1 ‐α)^2/3, 203.67 kJ·mol^?1 and 10^20.61s^?1, respectively. The critical temperature of thermal explosion of the compound is 182.2 °C. The values of ΔS^≠ ΔH^≠ and ΔG^≠ of this reaction are 143.3 J·mol^?1·K^?1, 199.5 kJ·mol^?1 and 135.5 kJ·mol^?1, respectively.     

Kinetic Studies on the Reaction of Sodium Hexacyanoferrate（ll） Complex with Peroxydisulfate Anion

The oxidation of Na₄Fe(CN)₆ complex by S₂O anion was found to follow an outer‐sphere electron transfer mechanism. We firstly carried out the reaction at pH=1. The specific rate constants of the reaction, k_ox, are (8.1±0.07)×10^?2 and (4.3±0.1)×10^?2 mol^?1·L·s^?1 at μ=1.0 mol·L^?1 NaClO₄, T=298 K for pH=1 (0.1 mol·L^?1 HCl0₄) and 8, respectively. The activation parameters, obtained by measuring the rate constants of oxidation 283–303 K, were ΔH^≠=(69.0±5.6) kJ·mol^?1, ΔS^≠=(?0.34±0.041)×10² J·mol^?1·K^?1 at pH=l and ΔH^≠=(41.3±5.5) kJ·mol^?1, ΔS^≠=(?1.27±0.33)×10² J·mol^?1·K^?1 at pH=8, respectively. The cyclic voltammetry of Fe(CN) shows that the oxidation is a one‐electron reversible redox process with E_1/2 values of 0.55 and 0.46 V vs. normal hydrogen electrode at μ=1.0 mol·L^?1 LiClO₄, for pH=1 and pH=8 (Tris). respectively. The kinetic results were discussed on the basis of Marcus theory.     

Crystal Structure, Phase Transition, and Thermodynamic Properties of Bis-dodecylammonium Tetrachlorozincate (C12H25NH3)2ZnCl4(s)

The crystal structure and composition of (C₁₂H₂₅NH₃)₂ZnCl₄(s) were characterized by chemical and elemental analysis, X‐ray powder diffraction technique and X‐ray crystallography. The lattice energy of the title compound was calculated to be U_POT=888.82 kJ·mol^?1. Low temperature heat capacities of the title compound have been measured by a precision automated adiabatic calorimeter over the temperature range from 80 to 403 K. An obvious solid to solid phase transition occurred in the heat capacity curve, and the peak temperature, molar enthalpy and molar entropy of the phase transition of the compound were determined to be T_trs= (364.02±0.03) K, (_trsH_m= (77.567±0.341) kJ·mol^?1, and (_trsS_m= (213.77±1.17) J·K^?1·mol^?1, respectively. Experimental molar heat capacities before and after the phase transition were respectively fitted to two polynomial equations. The smoothed molar heat capacities and fundamental thermodynamic functions of the sample relative to the standard reference temperature 298.15 K were calculated and tabulated at an interval of 5 K.     

氢过碘酸）合银（III）配离子氧化L-脯氨酸的反应动力学及机理

L-脯氨酸独有的亚胺基使其在生物医药领域具有许多独特的功能,并广泛用作不对称有机化合物合成的有效催化剂。本文在碱性介质中研究了二（氢过碘酸）合银（III）配离子氧化 L-脯氨酸的反应。经质谱鉴定,脯氨酸氧化后的产物为脯氨酸脱羧生成的 γ-氨基丁酸盐;氧化反应对脯氨酸及Ag(III) 均为一级;二级速率常数 k′ 随 [IO₄^-] 浓度增加而减小,而与 [OHˉ] 的浓度几乎无关;推测反应机理应包括 [Ag(HIO₆)₂]^5-与 [Ag(HIO₆)(H₂O)(OH)]^2-之间的前期平衡,两种Ag（III）配离子均作为反应的活性组分,在速控步被完全去质子化的脯氨酸平行地还原,两速控步对应的活化参数为： k₁ (25 ^oC)＝1.87±0.04（mol·L^-1)^-1s^-1,∆ H₁^≠＝45±4 kJ · mol^-1, ∆ S₁^≠＝-90±13 J· K^-1·mol^-1 and k₂ (25 ^oC) ＝3.2±0.5（mol·L^-1)^-1s^-1, ∆ H₂^≠＝34±2 kJ · mol^-1, ∆ S₂^≠＝-122 ±10 J· K^-1·mol^-1。本文第一次发现 [Ag(HIO₆)₂]^5-配离子也具有氧化反应活性。     

Studies on Thermodynamics Features of the Interaction between Imidacloprid and Bovine Serum Albumin

At different temperatures, the interactions between imidacloprid （IMI） and bovine serum albumin （BSA） were investigated with a fluorescence quenching spectrum, a synchronous fluorescence spectrum, a three-dimensional fluorescence spectrum and an ultraviolet-visible spectrum. The average values of bonding constants （KLB： 3.424 × 10^4 L,mol^-1）, thermodynamic parameters （△H： 5.188 kJ,mol^-1, △G^（○—）：-26.36 kJ,mol^-1, △S： 103.9 J,K^-1,mol^-1） and the numbers of bonding sites （n： 1.156） could be obtained through Stern-Volmer, Lineweaver-Burk and ther- modynamic equations. It was shown that the fluorescence of BSA could be quenched for its reactions with IMI to form a certain kind of new compound. The quenching belonged to a static fluorescence quenching, with a non-radiation energy transfer happening within a single molecule. The thermodynamic parameters agree with △H〉 0, △S〉0 and△G^（○-）〈0, suggesting that the binding power between IMI and BSA should be mainly a hydrophobic interaction.     

水合烟酸铜Cu(Nic)2•H2O(s)(Nic＝烟酸)的合成、表征及热力学性质

近几十年来,烟酸盐类化合物或配合物由于优越的吸收率高和无毒副作用等特点使其在化妆品、药品和食品等领域作为营养添加剂具有重要应用前景。然而,这类化合物的基础热力学数据极其缺乏,从而限制了这类化合物的理论研究和应用开发的深入开展。为此,本论文利用室温固相合成方法和球磨技术合成了一种新化合物Cu(Nic)2•H2O(s),利用化学分析、元素分析、FTIR和X-射线粉末衍射技术表征了它的结构和组成,利用精密自动绝热热量计准确地测量了它在78-400 K温区的摩尔热容。在热容曲线的T ＝ 326-346 K温区观察到一个明显的固-液相变过程。利用相变温区三次重复实验热容的测量结果确定了此相变过程的峰温、相变焓和相变熵分别为：Tfus＝(341.290 ±0.873) K, DfusHm＝(13.582±0.012) kJ×mol-1, DfusSm＝(39.797±0.067) J×K-1×mol-1。通过最小二乘法将相变前和相变后的热容实验值分别拟合成了热容对温度的两个多项式方程。通过热容多项式方程的数值积分,得到了这个化合物的舒平热容值和相对于298.15 K的各种热力学函数值,并且将每隔5 K的热力学函数值列成了表格。