不同形貌ZnO纳米结构的电子显微分析

控制实验合成条件,利用溶胶-凝胶法和化学溶液生长法制备出不同形貌的ZnO纳米结构。采用X射线衍射仪(XRD)、扫描电子显微镜( SEM) 以及透射电子显微镜(TEM)等多种测试手段对ZnO纳米结构的微观形态及晶相进行了分析。结果表明:3种ZnO纳米结构形貌虽不同,但均具有Z nO六方纤锌矿晶相结构。ZnO纳米棒和花状ZnO纳米结构为单晶,生长方向均沿(0001)方向。ZnO纳米球则为多晶。     

花球状异质结构复合材料ZnS/ZnO/ZnWO4多模式光降解与光解水制氢

通过微波辅助水热两步法制备了复合材料ZnS/ZnO/ZnWO_4,并采用X射线衍射(XRD)、紫外-可见漫反射吸收光谱(UVVis DRS)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、高分辨透射电子显微镜(HRTEM)以及N_2吸附-脱附等测试手段对其晶相结构、组成、形貌、表面物理化学性质及光吸收性能等进行了表征。结果显示,该复合材料呈现大小均匀的花球状结构,其花球是由立方晶相ZnS纳米颗粒、六方晶相ZnO与单斜晶相ZnWO_4纳米棒构成。微波的极化作用导致复合材料ZnO/ZnWO_4的晶粒尺寸、比表面积和孔体积较单体ZnWO_4明显变大。再次微波辐射复合ZnS后,复合材料ZnS/ZnO/ZnWO_4的晶粒尺寸进一步变大,同时二次微波作用导致其比表面积和孔体积由于花球内部的紧致而变小,但复合材料依旧保持花球状结构。以孔雀石绿为目标降解物,研究了花球状ZnS/ZnO/ZnWO_4增强的多模式光催化降解性能。而光解水制氢实验结果表明,ZnS/ZnO/ZnWO_4复合材料具有优异的产氢能力(376.9μmol·h~(-1)·g~(-1)),是市售P25的246.5倍,其增强的光解水制氢性能与复合材料优异的花球形貌、三元异质结构以及光催化反应中的多途径电子传递有关。     

形貌可控ZnO微纳米结构的水热合成及光催化性能

以乙醇胺为辅助溶剂,采用水热合成法,制备了花状、梭状和剑状的ZnO微纳米结构。采用扫描电镜(SEM)、X射线衍射(XRD)、光致发光光谱(PL)和拉曼光谱等测试手段对样品的形貌、结构、晶相等进行了表征。结果表明所有样品均为六方纤锌矿结构ZnO;其形貌和结晶度可通过改变物质的量的配比nZn2+/nOH-来调控。探讨了反应物配比对产物形貌结构的影响,乙醇胺对不同形貌ZnO的制备起到至关重要作用。以亚甲基蓝为目标降解物,采用紫外-可见吸收光谱(UV-Vis)并结合低温氮吸附-脱附比表面测试(BET),研究了花状、梭状和剑状ZnO的光催化活性。结果表明,与商用ZnO相比,制备的ZnO具有更好的光催化活性;样品催化活性与其比表面积不成正比,具有最小比表面积的花状ZnO拥有最好的光催化活性,这可能是由于其低的结晶度和特殊的花状形貌所致。     

Ag/ZnO/ZnSe三元异质结的合成及其可见光光催化性能

以Ag纳米线为模板,通过两步水浴法合成了Ag/ZnO/ZnSe三元异质结光催化材料。利用场发射扫描电子显微镜(FESEM)、X射线能谱仪(EDS)、X射线衍射仪(XRD)以及透射电子显微镜(FETEM)对样品的形貌和结构进行了表征。结果显示,Ag/ZnO/ZnSe三元异质结为蠕虫状的Ag/ZnO二元异质结外镶嵌着ZnSe小颗粒。在可见光下,对比纯Ag纳米线、纯ZnO纳米球、Ag/ZnO异质结对罗丹明B的可见光降解效率,结果发现Ag/ZnO/ZnSe异质结表现出了更高的光催化效率。其光催化性能的提高主要是由于Ag/ZnO/ZnSe异质结的作用促使电子空穴对的分离,降低了电子空穴对的复合机率,从而提高了材料的光催化效率。     

Y掺杂的ZnO纳米纤维材料的制备及其气敏传感器作用机理

采用静电纺丝法成功制备了Y掺杂的ZnO纳米纤维.并通过X射线衍射(XRD),扫描电子显微镜(SEM),能量色散X射线(EDX),透射电子显微镜(TEM)以及热重差热分析(TG-DTA)等手段对样品的结构和形貌进行了表征分析.同时用纯的ZnO和Y掺杂的ZnO纳米纤维制备了传感器,对浓度为(1-200)×10^-6 (体积分数)丙酮的气敏特性进行了测试分析.测试结果表明,可以通过简单控制纳米纤维中Y的含量,来微调该传感器的气敏特性.同时也发现通过Y掺杂, ZnO纳米纤维对丙酮的气敏特性有所改善,表现出很高的响应.纯ZnO和Y掺杂ZnO制成的传感器对几种潜在干扰气体表现出良好的选择性,比如氨气、苯、甲醛、甲苯以及甲醇.本文最后也讨论了该传感器的气敏作用机理.     

Sn掺杂ZnO纳米针的结构及其生长机制(英文)

利用包括磁控溅射和热氧化的两步法在Si(111)衬底上制备了Sn掺杂ZnO纳米针.首先用磁控溅射法在Si(111)衬底上制备Sn:Zn薄膜,然后在650℃的Ar气氛中对薄膜进行热氧化,制备出Sn掺杂ZnO纳米针.样品的结构、成分和光学性质采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、高分辨透射电子显微镜(HRTEM)、能量散射X射线(EDX)谱和光致发光(PL)光谱等技术手段进行分析.结果表明,制备的样品为具有六方纤锌矿结构的单晶Sn掺杂ZnO纳米针,Sn掺杂量为2.5%(x,原子比),底部和头部直径分别为200-500 nm和40 nm,长度为1-3μm,结晶质量较高.室温光致发光光谱显示紫外发光峰比纯ZnO的发光峰稍有蓝移,这可归因于能谱分析中探测到的Sn的影响.基于本实验的实际条件,简单探讨了Sn掺杂ZnO纳米针的生长机制.     

ZnO/ZnS大面积单晶异质结及其光电性能研究

ZnO和ZnS是重要的Ⅱ-Ⅵ族宽禁带半导体材料,二者之间形成的异质结具有Ⅱ型能带结构,可以促使受激载流子实现空间分离,延长受激载流子的寿命,从而提高材料的光催化和光电探测性能。本文利用物理气相沉积方法,首次在ZnO块状单晶衬底上生长了一层ZnS单晶薄膜,薄膜由厚约4nm、边长几百纳米,取向一致的等边三角形纳米片组成。X射线衍射和透射电子显微镜的表征结果显示,ZnS薄膜与ZnO衬底具有单一外延取向关系。阴极射线荧光光谱表明ZnS薄膜的制备显著提高了ZnO单晶片可见光荧光发光峰的强度。此外,对ZnO/ZnS异质结的紫外光电探测性能的研究结果显示,异质结对不同波长的紫外光均有响应,光响应的上升弛豫时间和下降弛豫时间分别为200ms和1050ms,展示了较好的光电应用潜力。     

原位水热合成SrTiO3/TiO2复合纳米纤维及光催化性能

以利用静电纺丝技术制备的TiO2纳米纤维为模板和反应物,原位水热合成了具有异质结构的SrTiO3/TiO2复合纳米纤维.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、能量散射光谱(EDS)、高分辨透射电子显微镜( HRTEM)和X射线光电子能谱(XPS)等测试手段对样品的结构和形貌进行了表征.用罗丹明B(RB)模...     

微米级花状结构铜/聚乙烯吡咯烷酮的制备及其抗菌性能

采用液相还原的方法,以聚乙烯吡咯烷酮(PVP)为修饰剂,氯化铜为前驱体,水合肼为还原剂,成功制备了微米级Cu/PVP花状结构.采用扫描电子显微镜和X射线粉末衍射仪分析了所得样品的形貌与结构;利用差热分析测定了样品的热稳定性,并采用肉汤稀释法测试了其抗菌性能.结果表明,所制备的样品具有由多个Cu/PVP圆片组装而成的直径为6μm的花状结构,其形貌依赖于反应条件.与此同时,花状结构的Cu/PVP对金黄色葡萄球菌和大肠杆菌具有明显的抗菌作用,相应的最小抑菌浓度(MIC)和最小杀菌浓度(MBC)分别为:41.25mg/L、82.5mg/L,以及20.63mg/L、82.5mg/L.与单一Cu纳米微粒相比,花状结构的Cu/PVP复合物的抗菌持久性明显较好.     

WO3/TiO2 复合纤维的制备及储能光催化性能

以钛酸正丁酯为前驱体, 采用静电纺丝技术制得了纯锐钛矿TiO2纤维, 并以其为基质, 通过水热法制备了具有异质结构的WO3/TiO2复合纤维. 利用X射线衍射仪(XRD)、 扫描电子显微镜(SEM)、 能量色散光谱仪(EDS)、 透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等对样品的结构和形貌进行了表征. 以罗丹明B的脱色降解为模型反应, 考察了样品的光催化性能和储能光催化性能. 结果表明, 花状WO3微球包裹在TiO2纤维上, 得到了具有异质结构的WO3/TiO2复合纤维光催化剂. WO3与TiO2复合有利于光生载流子的输运和分离, 增强了体系的量子效率, 提高了光催化活性. WO3/TiO2 复合纤维经光照处理后, 在黑暗条件下显示出储能光催化特性.     

Preparation of carbon nanotubes/BiOBr composites with higher visible light photocatalytic activity

A novel flower-like photocatalyst CNTs/BiOBr was successfully prepared by a facile hydrothermal method. The morphology and the physicochemical properties of the prepared samples were investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectrometry (EDX), and UV-visible diffuse reflectance spectroscopy (UV-vis DRS). The photocatalytic activity was evaluated by degradation of Rhodamin B (RhB) dye. It was demonstrated that CNTs/BiOBr photocatalyst could effectively photodegrade RhB under visible light (VL) irradiation.     

ZnO/CdS复合材料的合成与可见光催化性能

采用喷雾辅助气相沉积法在水热法合成的ZnO纳米线上沉积CdS纳米颗粒。采用X射线衍射仪（XRD）、激光拉曼仪（Raman）、扫描电镜（SEM）、透射电镜（TEM）、X射线光电子能谱分析谱（XPS）和紫外可见漫反射光谱等测试手段对复合光催化剂进行表征。结果表明,3~10 nm的CdS纳米粒子修饰在直径约为100 nm ZnO纳米线的表面。XPS和Raman表明复合材料中ZnO和CdS之间存在化学相互作用。可见光催化降解罗丹明B实验结果表明ZnO/CdS复合材料的催化性能优于单相CdS或ZnO,沉积时间为30 s合成的ZnO/CdS速率常数分别是CdS和ZnO的2.91和4.03倍,且具有较高的稳定性。ZnO/CdS复合材料光催化性能增强的可能原因为光吸收范围的拓展和光生载流子分离效率的提高。     

碳点修饰多孔ZnO纳米棒增强光催化性能

Porous ZnO nanorods that displayed excellent photocatalytic degradation of organic pollutants (RhB and phenol) were prepared via a solvent thermal method followed by surface modification with carbon dots (C-dots) using a deposition method. The photocatalysts were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and ultraviolet-visible (UV-Vis) spectroscopy. The degradation of the organic pollutants using the nanorods was tested under Xe-light illumination and was enhanced following C-dot modification. Nanorods that were modified by the C-dots at a mass fraction of 1.2% (CZn1.2) exhibited the highest photocatalytic activity for the degradation of RhB, which was 2.5 times of the pure porous ZnO nanorods. Additionally, the modified nanorods with strangely oxidation ability could catalyze the degradation of phenol by open-rings reaction under Xe-light illumination. The improved photocatalytic activity was attributed to the effective separation of the photogenerated electrons and holes, in which the C-dots served as the receptor of the photogenerated electrons.     

ZnO/graphene-oxide nanocomposite with remarkably enhanced visible-light-driven photocatalytic performance

In this work, a high-performance photocatalyst of ZnO/graphene-oxide (ZnO/GO) nanocomposite was synthesized via a facile chemical deposition route and used for the photodegradation of organic dye from water under visible light. The nanocomposite was characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller N(2) adsorption-desorption analysis, and UV-Vis diffusion reflectance spectroscopy. The ZnO/GO nanocomposite consisting of flower-like ZnO nanoparticles anchored on graphene-oxide sheets has a high surface area and hierarchical porosity, which is benefit to the adsorption and mass transfer of dye and oxygen species. For the photodegradation of organic dyes under visible light, ZnO/GO nanocomposite exhibited remarkably enhanced photocatalytic efficiency than graphene-oxide sheets and flower-like ZnO particles. Moreover, the photocatalytic efficiency of ZnO/GO nanocomposite could be further improved by annealing the product in N(2) atmosphere. The outstanding photocatalytic performance was ascribed to the efficient photosensitized electron injection and repressed charge carriers recombination in the composite with GO as electron collector and transporter, thus leading to continuous generation of reactive oxygen species for the degradation of methylene blue.     

Microwave-Assisted Hydrothermal Preparation, Characterization and Photocatalytic Properties of a Chrysanthemum-Shaped ZnWO4 Photocatalyst

A novel chrysanthemum-shaped monocline ZnWO₄ photocatalyst was synthesized by microwave-assisted hydrothermal method with Na₂WO₄·2H₂O and Zn(NO₃)₂·6H₂O as raw materials at different reaction temperatures. The prepared ZnWO₄ photocatalysts were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy, Photoluminescence spectrum (PL) and UV–Vis absorption spectrum (UV–Vis). The photocatalytic property of the prepared chrysanthemum-shaped monocline ZnWO₄ photocatalyst was evaluated by the degradation of Rhodamine B (RhB) in aqueous solution. The effects of reaction temperature on the photocatalytic degradation efficiency of RhB were investigated. The results indicated that the chrysanthemum-shaped monocline ZnWO₄ photocatalyst is prepared by foliated powders with the sizes of about 30 nm and 500 nm respectively at 160 and 220 °C. The PL relative intensity of prepared ZnWO₄ photocatalyst is apparently intensifying with increasing temperature. The photocatalytic property decreases with the increasing recombination probability of the excited electrons and holes. The chrysanthemum-shaped monocline ZnWO₄ photocatalyst prepared at 160 °C possesses the best photocatalytic property, and the degradation efficiency of RhB at 180 min UV-light irradiation is achieved 75 %. The ZnWO₄ has good reusability property on degradation of RhB and the degradation rate is still higher than 65 % after three cycles.     

A study on electrodeposited of ZnO/ZnS heterostructures

ZnO/ZnS heterostructures were synthesized by a two steps electrochemical deposition method. Firstly, ZnS layer was deposited from an aqueous solution containing Na₂S₂O₃ and ZnSO₄ onto indium-doped tin oxide (ITO) coating glass substrate at two deposition potentials. Then, ZnO nanostructures were deposited from an aqueous solution of Zn(NO₃) onto ZnS surface. The as-obtained samples were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), Raman and UV-visible analysis. The results indicate that the electrodeposition of ZnS layer at ?0.9 V give the best proprieties of ZnO/ZnS heterostructures. Homogeneous and uniform surface of ZnO/ZnS heterostructure was confirmed by AFM images. The XRD patterns indicates a high crystallinity of ZnO/ZnS. A high transmittance of 65% was also noted from UV-Visible spectra and band gap energy as large as 3.6?eV was found.     

ZnO/BiOI微球的合成及其光催化性能

通过一步溶剂热法合成ZnO/BiOI纳米复合材料,在Bi（NO₃）₃·6H₂O、KI、ZnO和乙二醇（EG）溶剂中,制备出的样品尺寸和形貌采用X射线粉末衍射（XRD）、场发射扫描电镜（FESEM）、高分辨透射电镜（HRTEM）、紫外-可见漫反射光谱（DRS）、X射线光电子能谱（XPS）、N₂吸附-脱附等,对实验所得产物的组成、结构及光学性质等进行表征。以染料罗丹明B（RhB）水溶液和气态乙醛作为降解对象,采用BiOI、ZnO/BiOI和ZnO微纳材料作为光催化剂,通过对BiOI、ZnO/BiOI和ZnO微纳材料在可见光下光催化降解染料罗丹明B（RhB）水溶液和气态乙醛,结果表明多孔微纳材料的ZnO/BiOI具有更高的降解效率,实验表明多孔微纳材料的ZnO/BiOI具有更高的氧空位浓度,因此使其催化活性增强,讨论了其可能的催化活性机理。     

球磨法制备复合光催化剂Bi12TiO20/ZnO及其光催化性能

本文用水作为分散介质,采用球磨法掺杂一定量的Bi₁₂TiO₂₀于ZnO中制备复合光催化剂Bi₁₂TiO₂₀/ZnO. 利用UV-Vis、XRD和SEM等仪器对样品进行了分析与表征. 通过对甲基橙的氧化来研究其光催化活性. 结果表明,光催化剂Bi₁₂TiO₂₀/ZnO对甲基橙氧化的催化活性高于氧化锌的催化活性.当Bi₁₂TiO₂₀的掺杂量为0.5%(质量分数),球磨时间为12 h,焙烧温度为300℃时,光照20 min后,复合光催化剂Bi₁₂TiO₂₀/ZnO对甲基橙的降解率可达到95.2%.     

ZnO/BiOI微球的合成及其光催化性能

通过一步溶剂热法合成ZnO/BiOI纳米复合材料,在Bi（NO₃）₃·6H₂O、KI、ZnO和乙二醇（EG）溶剂中,制备出的样品尺寸和形貌采用X射线粉末衍射（XRD）、场发射扫描电镜（FESEM）、高分辨透射电镜（HRTEM）、紫外-可见漫反射光谱（DRS）、X射线光电子能谱（XPS）、N₂吸附-脱附等,对实验所得产物的组成、结构及光学性质等进行表征。以染料罗丹明B（RhB）水溶液和气态乙醛作为降解对象,采用BiOI、ZnO/BiOI和ZnO微纳材料作为光催化剂,通过对BiOI、ZnO/BiOI和ZnO微纳材料在可见光下光催化降解染料罗丹明B（RhB）水溶液和气态乙醛,结果表明多孔微纳材料的ZnO/BiOI具有更高的降解效率,实验表明多孔微纳材料的ZnO/BiOI具有更高的氧空位浓度,因此使其催化活性增强,讨论了其可能的催化活性机理。     

Au纳米粒子负载的ZnO空心球复合材料的光生电荷转移行为及光催化活性

通过简单的两步法合成了不同负载量的Au/ZnO空心球。采用扫描电子显微镜(SEM),X射线衍射(XRD),X射线光电子能谱(XPS)及紫外-可见漫反射光谱(UV-Vis DRS)对样品的形貌、结构、组成和晶相等进行一系列的表征。以罗丹明B (RhB)为目标降解物,探究了Au/ZnO空心球的光催化活性。结果表明,适量Au修饰的ZnO光催化剂在混合光下20 min内对RhB的降解率达到73%。利用表面光电压谱(SPS)和瞬态光电压(TPV)技术,探讨了Au修饰后对ZnO光诱导电荷转移行为与光催化性能之间的关系。结果表明,混合光照下Au/ZnO空心球光降解性能的提高主要归因于作为电子受体的Au纳米粒子与ZnO之间形成的强的电子相互作用。适量Au纳米粒子的负载能够提高ZnO空心球中光生载流子的分离效率,相应地延长载流子的传输时间,增加光生电荷的寿命,从而促进其光催化活性的提高。