金纳米粒子-胱氨酸三维网状结构的形成及其光谱特性研究

用柠檬酸三钠还原法制备了水溶性金纳米粒子, 粒子的平均粒径为4.5 nm, 它与胱氨酸作用后, 胱氨酸利用双硫键在其表面成功地进行了自组装, 获得了金纳米粒子-胱氨酸的三维网状结构. 用紫外-可见光谱、光散射光谱、透射电子显微镜等手段对胱氨酸组装前后的金纳米粒子进行了表征. 结果显示, 粒子与粒子之间, 通过静电引力形成了离子键, 吸收光谱变化明显, 金纳米粒子特征吸收峰由组装前518 nm红移到670 nm, 溶液颜色也相应由酒红色变为蓝紫色, 求出了金纳米粒子-胱氨酸三维网状结构形成过程中胱氨酸的最佳量, 金与胱氨酸的物质的量比为1∶1. 对于4.5 nm的金纳米粒子, 只有14%左右的胱氨酸在金纳米粒子的表面进行了自组装, 而多余的86%的胱氨酸未与金纳米粒子作用; 其共振瑞利散射光谱具有潜在的应用价值. 该研究对以金纳米粒子为基础的新材料制备进行了有益的探索.     

电化学沉积法制备金（核）-铜（壳）纳米粒子阵列

以组装在有机分子自组装膜/金基底电极上的Au纳米粒子阵列为电化学沉积模板,制备了金(核)-铜 (壳)纳米粒子阵列.选用巯基十一胺（AUDT）和巯基癸烷（DT）混合自组装膜作为基底电极与Au纳米粒子的耦联层,可以在一定的电位下实现金属Cu在Au纳米粒子上的选择性沉积.将沉积电位控制在－0.03 V（vs SCE）时,沉积初期（t ≤ 15 s,沉积粒子粒径 ≤ 20 nm ）金(核)-铜 (壳)粒子具有良好的单分散性和近似球形,而且粒径实验值同计算值非常吻合.     

分形等离激元黑金的热电子催化性能

借鉴电镀工业中过电流“烧焦”现象, 在过电流沉积条件下一步制备出等离激元黑金. 扫描电子显微镜、 透射电子显微镜、 X射线衍射和紫外-可见-近红外吸收光谱等表征结果显示, 该黑金是具有三维分形结构的多晶纳米金, 可以在 400~1800 nm宽波段范围内吸收光. 电催化甲醇结果显示, 黑金在宽波长光照下可以将甲醇的电催化效率提高 15.2%, 其主要贡献来源于等离激元生成的热电子, 而一小部分来自环境热. 在不同的单色光照条件下, 黑金的催化效率差别不大, 表明其对光能的利用没有明显的波长选择性.     

金纳米粒子在氨基表面上的组装-pH值的影响

用原子力显微镜（AFM）和表面增强喇曼光谱（SERS）研究了pH值对金纳米粒子在Au／巯基苯胺自组装膜表面上组装效果的影响．AFM结果表明，金纳米粒子在表面上的覆盖度随pH值表现出规律性的变化，巯基苯胺自组装膜的SERS强度随pH值的变化也有类似的趋势．在磁性环境下，氨基未质子化，金粒子难以组装上，而在酸性条件下，氨基质子化带正电，金粒子与基底容易结合．我们认为金纳米粒子和氨基之间的作用属于静电力，pH值同时影响膜表面氨基的质子化程度和金纳米粒子表面的带电量．     

气-液界面Au纳米粒子网状结构薄膜的制备及SERS性能研究

本研究通过自组装法在气-液界面得到Au纳米粒子网状结构,并通过进一步生长得到连续的Au纳米粒子网状结构薄膜.该方法无需加入任何诱导剂,在室温条件下即可得到稳定性良好的纳米金薄膜.通过改变HAuCl_4和AgNO_3相对用量、陈化时间等条件对网状结构薄膜的形成机理进行了研究.结果发现,AgNO_3用量对Au纳米粒子薄膜的形成至关重要,通过调控AgNO_3用量可以促进纳米金粒子间的融合并形成纳米链、进一步演化为纳米链网状结构.在初步形成的Au纳米粒子网状结构表面通过抗坏血酸还原进一步生长纳米金粒子,有利于形成较大面积、较好稳定性的纳米Au粒子网状结构薄膜.以对氨基苯硫酚(4-ATP)作为探针分子,研究表明,与未发生组装的金纳米粒子相比,自组装形成的Au纳米粒子网状结构薄膜对4-ATP具有较强的表面增强拉曼效应.     

金纳米粒子表面自组装巯基十一烷醇单分子层体系的制备及其光散射特性研究

采用柠檬酸钠还原法制备了水相金纳米粒子, 通过巯基的自组装, 成功获得了巯基十一烷醇(MUN)单分子层保护的金纳米粒子. 用紫外可见光谱、透射电子显微镜、激光散射粒度分析、同步散射光谱和发射光谱等手段对组装前后的金纳米粒子的性质进行了研究. 结果表明: 制备的金纳米粒子最大吸收波长518 nm, 形状规则, 粒度均匀, 平均粒径为14.6 nm, 每个粒子含有约9.64×10⁴原子; 组装之后的金纳米粒子表面等离子体共振吸收峰红移17.0 nm, 平均粒径增大为20.2 nm, 组装层的平均厚度2.8 nm, 与MUN分子长度相当, 结合量实验证明每一个金纳米粒子可以结合约7.52×10³个MUN, 表面覆盖率为83.6%, 粒子分散均匀, 稳定性增强可长期保存; 同步散射光谱变化和发射光谱中分频、差频和倍频峰的存在证明, 金纳米粒子组装前后均具有非线性光学特性.     

金纳米粒子组装体系粒子密度与SERS强度的关系

利用纳米粒子组装技术制备出金基底／巯基苯胺自组装膜偶联层／金纳米粒子的“三明治”结构。实验结果显示,该结构对偶联层分子的喇曼光谱显示出很好的增强效应,增强因子可达１０＾５;在表面粒子密度（粒子覆盖度）较低时,表面增强喇曼散射（ＳＥＲＳ）强度与表面粒子密度近似呈线性关系;随着表面粒子密度的增加,这种线性关系出现负偏差并在表面粒子密度较高区域出现一个平台;在６０￣１１０ｎｍ范围内大粒径金粒子对喇曼光谱     

碳纳米粒子支撑的钯纳米催化剂在甲酸氧化中的电催化活性

采用化学还原法制备了碳纳米粒子支撑的钯纳米结构(Pd-CNP). 透射电镜表征显示在Pd-CNP纳米复合物中,金属Pd呈菜花状结构,粒径约20~30 nm。它们由许多更小的Pd纳米粒子（3~8 nm）组成. 电化学研究表明,虽然Pd-CNP的电化学活性面积比商业Pd黑低40%（可能原因是部分Pd表面被一层碳纳米粒子覆盖）,但其对甲酸氧化却表现出更好的电催化活性：质量比活性和面积比活性都比Pd黑高几倍. 催化活性增强的原因可能是碳纳米粒子支撑的Pd纳米结构具有特殊的层次化结构,可以形成更多的活性位,以及表面位更利于反应进行.     

金核银壳纳米粒子薄膜的制备及SERS活性研究

采用柠檬酸化学还原法制备金溶胶, 通过自组装技术在石英片表面制备金纳米粒子薄膜, 在银增强剂混合溶液中反应获得金核银壳纳米粒子薄膜. 用紫外-可见吸收光谱仪和原子力显微镜(AFM)研究了不同条件下制备的金核银壳纳米粒子薄膜的光谱特性和表面形貌, 并以结晶紫为探针分子测量了金核银壳纳米粒子薄膜的表面增强拉曼光谱(SERS). 结果表明, 金纳米粒子薄膜的分布、银增强剂反应时间的长短对金核银壳纳米粒子薄膜的形成均有重要影响. 制备过程中, 可以通过控制反应条件获得一定粒径的、具有良好表面增强拉曼散射活性的金核银壳纳米粒子薄膜.     

基于Kretschmann结构的金银合金薄膜的SERS效应

利用Kretschmann棱镜耦合结构和532 nm激光光源,测试了金银合金薄膜的表面增强拉曼散射(SERS)效应,并与纯金薄膜的测试结果进行了比较.结果显示,在激发光为p偏振态且入射角近似等于表面等离子体共振(SPR)角时,附着于金银合金薄膜表面的Nile Blue分子的SERS信号达到最强,比利用纯金薄膜测得的SERS信号高约2倍.实验结果还表明,在金银合金薄膜表面自组装金纳米粒子后,Nile Blue吸附层的SERS信号比自组装纳米金之前测得的信号增强了至少3倍,比利用纳米金修饰的纯金薄膜测得的信号高出2倍多.在棱镜底面沿薄膜法线收集的SERS信号是完全非偏振光,而从棱镜侧面收集的SERS信号是p偏振光,是拉曼光借助SPR效应产生的定向发射.     

SEC Characterization of Au Nanoparticles Prepared through Seed-Assisted Synthesis

In this paper we report the use of size-exclusion chromatography (SEC) for rapid determination of the sizes and size distributions of Au nanoparticles (NPs) prepared by seed-assisted synthesis. Analytical separation of Au NPs was performed in a polymer-based column of pore size 400 nm. We characterized the sizes and size distributions of the Au NPs by using 10 mM sodium dodecyl sulfate (SDS) as mobile phase and obtained a linear relationship (R ² = 0.986) between retention time and size of Au NPs within the range 9.8–79.1 nm; the relative standard deviations of these retention times were less than 0.3%. These separation conditions were used to characterize the sizes and size distributions of Au NPs prepared by seed-assisted synthesis. In addition to observing the elution times of the Au NPs we also simultaneously characterized their size-dependent optical properties by spectral measurement of the eluting peaks by use of an on-line diode-array detector (DAD), i.e., monitoring of the stability of the Au NP products. By using this approach we found the presence of SDS was beneficial in stabilizing the synthesized Au NPs. We also found that the volume of Au metal ions used affected the sizes of the final products. SEC seems an efficient tool for characterizing the sizes of NPs fabricated by seed-assisted synthesis.     

Self‐Assembled Au Nanoparticles as Substrates for Surface‐Enhanced Vibrational Spectroscopy: Optimization and Electrochemical Stability

Three‐dimensional nanostructured metallic substrates for enhanced vibrational spectroscopy are fabricated by self‐assembly. Nanostructures consisting of one to 20 depositions of 13 nm‐diameter Au nanoparticles (NPs) on Au films are prepared and characterized by means of AFM and UV/Vis reflection–absorption spectroscopy. Surface‐enhanced polarization modulation infrared reflection–absorption spectroscopy (PM‐IRRAS) is observed from Au NPs modified by the probe molecule 4‐hydroxythiophenol. The limitation of this kind of substrate for surface‐enhanced PM‐IRRAS is discussed. The surface‐enhanced Raman scattering (SERS) from the same probe molecule is also observed and the effect of the number of Au‐NP depositions on the SERS efficiency is studied. The SERS signal from the probe molecule maximizes after 11 Au‐NP depositions, and the absolute SERS intensities from different batches are reproducible within 20 %. In situ electrochemical SERS measurements show that these substrates are stable within the potential window between ?800 and +200 mV (vs. Ag/AgCl/sat. Cl^?).     

内部具有可移动金核的中空银纳米颗粒的制备、表征及其表面增强拉曼效应

采用振荡法和种子生长技术制备出核壳结构的Au@SiO2纳米颗粒及夹层结构的Au@SiO2@Ag纳米颗粒, 用HF将Au@SiO2@Ag NPs夹层的SiO2溶解, 得到内部带有粒径为30 nm的可移动金核、壳层厚度约为30 nm的中空银纳米颗粒(Au@air@Ag NPs). 用扫描电子显微镜和透射电子显微镜对所得到的纳米微球的形貌进行了表征, 并以罗丹明B为探针分子研究了Au@air@Ag 纳米颗粒的表面增强拉曼(SERS)效应, 发现Au@air@Ag 纳米颗粒是一种可应用于SERS的理想材料.     

Oxidation of highly unstable <4 nm diameter gold nanoparticles 850 mV negative of the bulk oxidation potential

Here we describe the oxidation of <4 nm diameter Au nanoparticles (NPs) attached to indium tin oxide-coated glass electrodes in Br(-) and Cl(-) solution. Borohydride reduction of AuCl(4)(-) in the presence of hexanethiol or trisodium citrate (15 min) led to Au NPs <4 nm in diameter. After electrochemical and ozone removal of the hexanthiolate ligands from the thiol-coated Au NPs, Au oxidation peaks appeared in the range 0-400 mV vs Ag/AgCl (1 M KCl), which is 850-450 mV negative of the bulk Au oxidation peak near 850 mV. The oxidation potential of citrate-coated Au NPs is in the 300-500 mV range and those of 4 and 12 nm diameter Au NPs in the 660-780 mV range. The large negative shift in potential agrees with theory for NPs in the 1-2 nm diameter range. The oxidation potential of Au in Cl(-) solution is positive of that in Br(-) solution, but the difference decreases dramatically as the NP size decreases, showing less dependence on the halide for smaller NPs.     

Au Nanowire–Au Nanoparticles Conjugated System which Provides Micrometer Size Molecular Sensors

We report a new type of molecular sensor using a Au nanowire (NW)–Au nanoparticles (NPs) conjugated system. The Au NW–NPs structure is fabricated by the self‐assembly of biotinylated Au NPs on a biotinylated Au NW through avidin; this creates hot spots between NW and NPs that strongly enhance the Raman signal. The number of the Au NPs attached to the NW is reproducibly proportional to the concentration of the avidin, and is also proportional to the measured surface‐enhanced Raman scattering (SERS) signals. Since this well‐defined NW–NPs conjugated sensor is only a few micrometer long, we expect that development of multiplex nanobiosensor of a few tens micrometer size would become feasible by combining individually modified multiple Au NWs together on one substrate.     

表面增强拉曼散射强度与金纳米粒子粒径关系

表面增强拉曼散射（SurfaceenhancedRamanscattering,简称SERS）的增强机理主要分为两类’‘－‘’：电磁增强和化学增强．通常SERS活性表面的获得需要粗糙化．MOSkovitS最先提出,可将粗糙化的SERS活性表面模型化为平整金属基底上排列的金属胶体粒子“’．这样的模型与实际体系比较符合,同时给理论处理提供了便利．在这一模型基础之上,人们提出了一系列SERS电磁增强的理论计算方法’‘－“．在这些理论计算中,大多包含有SERS强度与粒径关系的结果．粒径对SERS强度的影响体现在两方面：1）SERS与粗糙度有关,粒径可视为粗…     

The effects of Au aggregate morphology on surface-enhanced Raman scattering enhancement

We have identified empirically a relationship between the surface morphology of small individual aggregates (<100 Au nanoparticles) and surface-enhanced Raman scattering (SERS) enhancement. We have found that multilayer aggregates generated greater SERS enhancement than aggregates limited to two-dimensional (2D) or one-dimensional structures, independent of the number of particles. SERS intensity was measured using the 730 cm(-1) vibrational mode of the adsorbed adenine molecule on 75 nm Au particles, at an excitation wavelength of 632.8 nm. To gain insight into these relationships and its mechanism, we developed a qualitative model that considers the collections of interacting Au nanoparticles of an individual aggregate as a continuous single entity that retains its salient features. We found the dimensions of the modeled surface features to be comparable with those found in rough metal surfaces, known to sustain surface plasmon resonance and generate strong SERS enhancement. Among the aggregates that we have characterized, a three 75 nm nanoparticle system was the smallest to generate strong SERS enhancement. However, we also identified single individual Au nanoparticles as SERS active at the same wavelength, but with a diameter twice in size. For example, we observed a symmetric SERS-active particle of 180 nm in diameter. Such individual nanoparticles generated SERS enhancement on the same order of magnitude as the small monolayer Au aggregates, an intensity value significantly stronger than predicted in recent theoretical studies. We also found that an aspect of our model that relates the dimensions of its features to SERS enhancement is also applicable to single individual Au particles. We conclude that the size of the nanoparticle itself, or the size of a protrusion of an irregularly shaped single Au particle, will contribute to SERS enhancement provided that its dimensions satisfy the conditions for plasmon resonance. In addition, by considering the ratio of the generated intensities of typical 2D Au aggregates to the enhancement of individual SERS-active particles, a value of approximately 2 is determined. Its moderate value suggests that it is not the aggregation effect that is responsible for much of the observed SERS enhancement but the surface region associated with the SERS-active site.     

Using SEC for Analyzing the Sizes of Au/Pt Core/Shell Nanoparticles

This paper describes the use of size-exclusion chromatography (SEC) to characterize the sizes of fabricated Au/Pt core/shell nanoparticles (NPs), which were monitored using a polymer-based SEC column (pore size: ca. 400 nm) and a mobile phase of 10 mM sodium dodecyl sulfate (SDS). The plot of the retention time with respect to the logarithm of the size of the Au NPs was very linear (R ² = 0.999) for NP diameters falling in the range from 5.3 to 59.9 nm. The relative standard deviation (n = 5) of these retention times was less than 0.20%. When using SEC to analyze synthetic products, we found that the sizes of the fabricated Au/Pt core/shell NPs could be controlled via modification of the volumes of the seed, SDS, and sodium hydroxide solutions. A good correlation existed between the sizes determined through SEC and those determined using transmission electron microscopy. Thus, polymer-based SEC appears to be a useful technique for monitoring the sizes of NPs—and nanomaterials in general.     

Rapidly Characterizing the Growth of Au Nanoparticles by CE

In this paper, we describe a capillary electrophoresis (CE)-based method for the rapid characterization of Au nanoparticles (NPs) prepared through seed-assisted synthesis. We effected the CE separation of these Au NPs using a mixed buffer of sodium dodecyl sulfate (SDS; 70 mM) and 3-(cyclohexylamino)-1-propanesulfonic acid (CAPS; 10 mM) at pH 10.0 under an applied potential of 20 kV. A linear relationship (R ² = 0.985) existed between the electrophoretic mobilities and the sizes of the Au NPs within a range of diameters from 5.3 to 59.9 nm; the relative standard deviations of these electrophoretic mobilities were below 0.9%. When using these conditions to analyze the products of seed-assisted syntheses, we found that the rate of addition of the reducing agent affected the size distribution of the NPs dramatically. CE analysis also revealed that the presence of NaOH in the synthesis medium minimized the sizes of the Au NPs. When using these conditions to analyze the Au NPs produced through seed-assisted synthesis, a good correlation existed between the sizes obtained using CE and transmission electron microscopy (TEM). Based on these findings, CE appears to be an efficient tool for characterizing the sizes of NPs fabricated through seed-assisted synthesis.     

银/金纳米线阵列表面增强拉曼基底的制备及对孔雀石绿的高灵敏度检测

利用种子介导的软模板生长方法制备了金纳米线(Au NWs)阵列, 通过调节生长温度控制Au NWs阵列的形貌, 最后在经硼氢化钠(NaBH₄)清洗过的Au NWs阵列上化学沉积银纳米颗粒(Ag NPs), 制得银/金纳米线(Ag/Au NWs)阵列作为表面增强拉曼散射(SERS)基底. 选用罗丹明6G(R6G)作为拉曼探针分子测定了Ag/Au NWs阵列的SERS性能. 结果表明, Ag/Au NWs阵列作为SERS基底具有高灵敏度、 优异的信号均匀性和良好的稳定性. 使用Ag/Au NWs阵列对孔雀石绿(MG)检测的检出限可低至1×10^-8 mol/L, 线性范围为 1×10^-8~1×10^-4 mol/L. NaBH₄可以在不影响SERS性能的情况下去除Ag/Au NWs阵列上吸附的分子, 使得 SERS基底可以重复使用. 使用Ag/Au NWs阵列对湖水中的MG进行检测, 得到了可靠的回收率, 证明Ag/Au NWs 阵列在检测环境水体中的孔雀石绿上具有应用潜力.