Au@SiO2核壳结构-表面增强拉曼光谱原位检测食品中的酸性橙Ⅱ

以具有核壳结构的Au@SiO2纳米颗粒为基底,建立了一种以表面增强拉曼(SERS)原位、快速检测食品中非法添加剂酸性橙Ⅱ的新方法.研究了活性硅加入量对所形成的Au@SiO2纳米颗粒的SERS活性的影响,制备了具有最佳SERS活性的Au@SiO2,并以此为SERS基底建立了酸性橙Ⅱ的分析方法,可实现0.17 mg/L酸性橙Ⅱ的SERS检测.将合成的Au@SiO2滴加到瓜子表面后,可以实现对瓜子表面酸性橙Ⅱ浓度为0.01 mg/g时的SERS检测,能够满足食品中酸性橙Ⅱ的测定要求,有望用于瓜子及其它可能被非法添加该物质的食品的现场、快速检测.     

水/甲苯界面制备均匀可循环SERS基底

采用在沸水浴中还原硅酸钠的方法制备壳层约4nm的Au@SiO2核壳纳米粒子,利用水/ 甲苯两相界面诱捕出其单粒子层膜并将这层膜转移到Si片上.作为对比,采用化学方法自组装Au@SiO2膜至ITO玻璃表面. 以1,4-对苯二硫作为探针分子考察了它们的SERS活性以及可循环使用性能. 研究结果表明,Au@SiO2核壳粒子可避免待测分子与基底直接接触,NaBH4溶液可作为基底循环的洗涤剂,经化学组装的基底的可循环性能较差,每次洗涤SERS效应均有一定程度降低,而两相界面形成的单粒子致密膜的SERS效应稳定性较好,其循环性能较高,即使洗涤10次后,SERS效应仍未明显降低,此膜可作为循环使用的SERS基底.     

Ag_核Au_壳金属复合纳米粒子的制备及表面增强拉曼光谱研究

在已制备好的Ag纳米粒子表面,通过化学还原的方法沉积生长Au包裹层,制备了粒子尺寸为50-70nm的Ag核Au壳复合纳米粒子.通过改变AuCl₄^-量,使Ag_100-xAu_x中Au的含量由x=0变为x=30.用UV-Vis吸收光谱和透射电子显微镜(TEM)对该结构纳米粒子进行了表征,并以对巯基苯胺(PATP)为探针分子进行表面增强拉曼光谱(SERS)研究.表面拉曼光谱表明,该结构的纳米粒子具有比Ag更强的SERS活性,随着Au:Ag比例的逐渐增加,其活性呈现先增大后减小的趋势,其最大增强约为Ag纳米粒子的10倍.     

碳纳米管@SiO_2@Ag纳米复合材料的制备及其表面增强拉曼效应

本文以SiO2为中间层,在多壁碳纳米管(MWCNTs)表面负载Ag纳米粒子,制备出CNTs@SiO2@Ag纳米复合材料,并采用TEM、XRD、UV-Vis、XPS等对纳米复合材料的结构、形貌和成分进行了表征,同时对该纳米复合材料的表面增强拉曼散射(Surface-enhanced Raman scattering,SERS)效应进行了研究。结果显示,Ag纳米颗粒有效提高了CNTs的SERS活性,纳米复合材料的拉曼峰强度是单纯CNTs拉曼峰强的近5倍。进一步研究了吸附罗丹明6G生物染料分子的SERS光谱,结果表明R6G分子的拉曼信号的质量与强度得到显著提高。因此,所制备的CNTs@SiO2@Ag纳米复合材料有望作为SERS的活性基底,应用于生物无损检测领域。     

不同Pt壳厚度Au_(core)@Pt_(shell)纳米粒子SERS效应

以Au粒子(55nm)为核,抗坏血酸为还原剂,将不同量的Pt沉积在Au核上,制得可控壳层厚度(0.3～6nm)的Pt包Au纳米粒子(Aucore@Ptshell).用紫外-可见吸收光谱、扫描电镜(SEM)、透射电镜(TEM)和电化学循环伏安法等观测Aucore@Ptshell纳米粒子的表面形貌、结构和性能.另以SCN-为探针,考察了Pt壳厚度对Aucore@Ptshell纳米粒子SERS信号的影响.结果表明,SCN-离子的SERS信号强度随Pt壳厚度的增加呈指数衰减,当Pt壳厚度为1.4nm时,Aucore@Ptshel纳米粒子表现出铂良好的电化学性能,又具有较强的SERS活性.     

铝纳米粒子表面引发聚合制备核壳纳米结构

利用硅烷偶联剂引发法制备核壳结构金属铝纳米粒子(Al NPs)@聚合物, 并研究了聚合反应时间和单体浓度对核壳结构尺寸的影响. 首先合成了硅烷偶联引发剂{2-溴-2-甲基-[3-(三甲氧基硅基)丙基]丙酰胺}, 并通过在甲苯中回流的方法, 将其锚定在金属铝纳米粒子表面. 然后, 在粒子表面引发甲基丙烯酸甲酯的原子转移自由基聚合, 形成聚甲基丙烯酸甲酯(PMMA)壳层. 通过核磁共振波谱仪(NMR)和傅里叶变换红外光谱仪 (FTIR)证明了引发剂和PMMA的成功接枝. 透射电子显微镜(TEM)图像表明, PMMA改性后的金属铝纳米粒子的尺寸和形貌基本不变, 且被厚度约为15 nm聚合物壳层完整均匀地包覆. 此外, 利用动态光散射(DLS)进一步揭示了聚合时间和单体浓度对核壳结构水合直径(D_h)的影响, 发现延长聚合时间或增加单体浓度均可显著提高核壳结构尺寸.     

无皂乳液聚合法制备聚甲基丙烯酸甲酯包覆厚度可控的纳米核-壳二氧化硅微球

用改进的Stöber法和无皂乳液聚合法制备窄分布的二氧化硅/PMMA核-壳纳米微球. 用改进的Stöber法将3-乙氧基甲基丙烯酸丙基硅烷(MPS)修饰在纳米的二氧化硅表面后, 用无皂乳液聚合法制备核-壳纳米微球. 该法简单有效且得到厚度均匀的聚合物包覆层. 随着单体MMA用量的增加, 用动态光散射法测量, PMMA壳层的厚度从6.4 nm增加到96.3 nm. 热重分析表明, PMMA的含量从22.25%增加到93.41%. 扫描电子显微镜和透射电子显微镜结果表明, 得到的是包覆良好、表面光滑的核-壳无机/聚合物纳米微球.     

碳纳米管@SiO2@Ag纳米复合材料的制备及其表面增强拉曼效应

本文以SiO₂为中间层,在多壁碳纳米管(MWCNTs)表面负载Ag纳米粒子,制备出CNTs@SiO₂@Ag纳米复合材料,并采用TEM、XRD、UV-Vis、XPS等对纳米复合材料的结构、形貌和成分进行了表征,同时对该纳米复合材料的表面增强拉曼散射(Surface-enhancedRamanscattering,SERS)效应进行了研究。结果显示,Ag纳米颗粒有效提高了CNTs的SERS活性,纳米复合材料的拉曼峰强度是单纯CNTs拉曼峰强的近5倍。进一步研究了吸附罗丹明6G生物染料分子的SERS光谱,结果表明R6G分子的拉曼信号的质量与强度得到显著提高。因此,所制备的CNTs@SiO₂@Ag纳米复合材料有望作为SERS的活性基底,应用于生物无损检测领域。     

Ni2P@CoP3核壳纳米球的制备、表征及其用于超级电容器性能

利用水热技术先后获得Ni纳米球和Ni@Co(OH)_2海胆状核壳纳米球前驱体,通过高温煅烧法获得NiO@CoO核壳纳米球,再以次磷酸钠为原料,通过高温磷化法最终获得Ni_2P@CoP_3核壳纳米球。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、高角度环形暗场像扫描透射电子显微镜(HAADF-STEM)、X射线粉末衍射仪(XRD)、能谱仪(EDS)及X射线光电子能谱(XPS)对产物的形貌、结构和组成进行表征。采用循环伏安(CV)、恒电流充放电(GCD)以及循环稳定性实验探索了电极材料的电化学性能。结果表明,Ni_2P@CoP_3核壳纳米球的直径约为400 nm,由六方系Ni_2P纳米核和立方相CoP_3纳米壳构成。相比单纯的Ni_2P或CoP_3纳米球,Ni_2P@CoP_3核壳纳米球发挥了复合结构的协同效应,更加有利于电解液的质子传递,促进了赝电容反应,表现出更高的比容量、稳定性和更长的循环寿命。     

光催化还原制备Au/Ag核壳结构纳米粒子及其修饰电极的电催化性能

以Keggin结构硅钨杂多酸H4SiW12O40(SiW12)为光催化还原剂,通过光化学还原法制备Au/Ag核壳结构纳米粒子. 透射电子显微镜分析显示,所得纳米粒子粒径为30～40 nm,呈均匀分散的球形颗粒,该制备方法的特点是可以较好的避免单金属纳米粒子的形成. 将Au/Ag核壳纳米粒子修饰到具有PVP膜的玻碳电极表面,得到SiW12-(Au/Ag)-PVP多层膜修饰电极. 该修饰电极在0.5 mol/L H2SO4介质中具有良好的电化学响应,在0～-0.75 V电位范围内,出现了3对归属于SiW12的氧化还原峰,且电极性能稳定,灵敏度高. 对H2O2的电催化还原性能明显优于单金属Ag纳米粒子修饰电极,说明Au核的存在可以很好的改善Ag的电催化性能,Au和Ag之间存在相互协同催化作用.     

Size-controllable synthesis of surface-enhanced Raman scattering-active gold nanoparticles coated on TiO2

As shown in the literature, gold nanoparticles (NPs) were popularly used in the fields of catalyst and surface-enhanced Raman scattering (SERS). In this work, size-controllable Au NPs coated on TiO(2) are synthesized by adjusting the pH of solutions based on sonoelectrochemical methods. The size-controlled Au NPs on TiO(2), ranging from 2 to 80 nm in diameter, can be obtained by varying the pH of solutions from 3 to 7 and placing the sample for 3 h before sonoelectrochemical reductions. The optimal particle sizes of Au NPs on TiO(2) to obtain the strongest SERS effects under an irradiation of 785 nm for probe molecules of adsorbed Rhodamine 6G (R6G) and deposited polypyrrole (PPy) are all ca. 60 nm.     

Imaging and SERS Study of the Au Nanoparticles Interaction with HPV and Carcinogenic Cervical Tissues

In this work, gold NPs were prepared by the Turkevich method, and their interaction with HPV and cancerous cervical tissues were studied by scanning electron microscopy, energy-dispersive x-ray spectroscopy, confocal and multiphoton microscopy and SERS. The SEM images confirmed the presence and localization of the gold NPs inside of the two kinds of tissues. The light absorption of the gold NPs was at 520 nm. However, it was possible to obtain two-photon imaging (red emission region) of the gold NPs inside of the tissue, exciting the samples at 900 nm, observing the morphology of the tissues. The infrared absorption was probably due to the aggregation of gold NPs inside the tissues. Therefore, through the interaction of gold nanoparticles with the HPV and cancerous cervical tissues, a surface enhanced Raman spectroscopy (SERS) was obtained. As preliminary studies, having an average of 1000 Raman spectra per tissue, SERS signals showed changes between the HPV-infected and the carcinogenic tissues; these spectral signatures occurred mainly in the DNA bands, potentially offering a tool for the rapid screening of cancer.     

AucoreCoshell纳米粒子的制备、表征及其表面增强拉曼光谱研究

在乙醇体系中和在制备好的Au纳米粒子表面, 用水合肼还原钴盐制备Co壳, 首次通过化学还原法制得核壳结构的Au-Co纳米粒子, 并通过控制钴盐的投料, 得到不同包裹层厚度的AucoreCoshell纳米粒子. 用扫描电子显微镜(SEM)和电化学循环伏安法(CV)等测试方法对其进行表征, 并用吡啶(Py)作为探针分子研究了其SERS效应.     

Preparation of Fe3O4@Ag SERS substrate and its application in environmental Cr(VI) analysis

A novel sensitive and recyclable SERS substrate which can actively concentrate chromate (Cr(VI)) in water and substantially enhance Raman signal was synthesized as uniform Fe(3)O(4)@Ag nanoparticles. The surface morphology, structure, and magnetic properties were characterized using transmission electron microscopy, atomic force microscopy, X-ray powder diffraction, X-ray photoelectron spectroscopy, and vibrating sample magnetometry analysis. The closely spaced Fe(3)O(4)@Ag substrate with a core-shell structure exhibited a 25 nm surface roughness. The high saturation magnetization at 48.35 emu g(-1) enabled the complete and rapid separation of the substrate from the solution. The sensitivity and reproducibility of the substrate were confirmed using a common SERS probe molecule, rhodamine 6G. SERS spectra of Cr(VI) in simulated and real contaminated water showed that the symmetric stretching vibrations of Cr-O occurred at 796 cm(-1). This SERS peak area exhibited a linear dependence (R(2)=0.9992) on the Cr(VI) concentration between 5 and 100 μg L(-1). Coexisting anions such as sulfate, nitrate, chloride, carbonate, and humic acid could decrease the sensitivity of the SERS analysis. However, the adverse effect of the competing ions may be eliminated by proper dilution of the raw sample. This study provides a reliable method for qualitative and quantitative analysis of Cr(VI).     

Internalization of PLGA nanoparticles coated with poloxamer 188 in glioma cells: A confocal laser scanning microscopy study

Internalization of poloxamer 188-coated PLGA nanoparticles (NPs) in GL261 murine glioma cells was studied using confocal laser scanning microscopy. For visualization, both poloxamer 188 (P188) and PLGA were labeled covalently with fluorescent dyes Rhodamine B and Cyanine5, respectively. The results indicated that the PLGA NPs coated with poloxamer 188 enter a cell as an integral core–shell structure, which can be helpful for gaining further insight into the in vivo performance of surfactant-coated polymeric NPs as core–shell delivery systems